Page 1
E Series
DHD675-E/DWU675-E/DHD775-E/DWU775-E
USER MANUAL
020-000515-01
Page 2
Addendum
The CD included with this printed manual contains an electronic copy in English. Please read all instructions before
using or servicing this product.
㓚␛₼▔⚺䤓⏘䥧᧨サ㦘䧏₼㠖䤓䟄⓾㦻᧨∎䞷㒥冃≽㦻ℶ❐ⓜ᧨庆Ⅳ兕㩴梔㓏㦘䤓㖖䯉ᇭ
Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les
instructions avant d'utiliser ou de réparer ce produit.
Il CD fornito con il manuale stampato contiene una copia elettronica in lingua italiano. Si prega di leggere tutte le
istruzioni prima di utilizzare o riparare questo prodotto.
Ʌɠᤅɇɾɑ˃ʰˊʇːɝҨዸɇɾɘȼɼɰɋ "# ɝɡơෙཙౘəɠ᭴ᠦႚȾᮭɕɘȼɼɰɋƢɅɠ༎
үʄẖᄭȴɽȶɡጞࣟዟɇɾɽၿɝơɆᤈጷṫɇȶƢ
ꎙ鰩꽱隱뼝颍붡뼝鷍꽩넽鱉&' 꾅鱉뼑鞵ꈑ鷑놹녅ꩡꚭ냹붡뼝뼍隕넽걪鱽鲙 ꚭ뇑븽냹ꩡ끞뿮냵
ꟹ걙뼍韥놹꾅ꑝ麕덵렝ꩡ뼢麙냹넲꽩ꚩ겑韥ꗉꅂ鱽鲙
&'
El DC incluido con este manual impreso contiene una copia electrónica en español. Por favor, lea todas las
instrucciones antes de usar o dar servicio a este producto.
Page 3
NOTICES
, .
COPYRIGHT AND TRADEMARKS
© 2013 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of
their respective holders.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the product is operated in a commercial environment. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of the product in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at the user’s own expense.
WARNING! Changes or modications not expressly approved by Christie could void the user’s
authority to operate the product.
FOR COMMERCIAL USE ONLY - POUR USAGE COMMERCIAL UNIQUEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING 2 CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
CET APPAREIL NUMÉRIQUE DE CLASSE A EST CONFORME AUX NORMES DÉFINIES
DANS LES RÉGLEMENTATIONS CANADIENNES SUR LES APPAREILS CAUSANT
DES INTERFÉRENCES RADIO (CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS, ICES-003, CLASS A).
Page 4
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products
or availability could occur which may not be reected in this document. Christie reserves the right
to make changes to specications at any time without notice. Performance specications are
typical, but may vary depending on conditions beyond Christie's control such as maintenance of
the product in proper working conditions. Performance specications are based on information
available at the time of printing. Christie makes no warranty of any kind with regard to this material,
including, but not limited to, implied warranties of tness for a particular purpose. Christie will not
be liable for errors contained herein or for incidental or consequential damages in connection with
the performance or use of this material.
The product is designed and manufactured with high-quality materials and components that can
be recycled and reused. This symbol
means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from regular waste. Please dispose of the product
appropriately and according to local regulations. In the European Union, there are separate
collection systems for used electrical and electronic products. Please help us to conserve the
environment we live in!
Canadian manufacturing facility is ISO 9001 and 14001 certied.
GENERAL WARRANTY STATEMENTS
For complete information about Christie’s limited warranty, please contact your Christie dealer. In
addition to the other limitations that may be specied in Christie’s limited warranty, the warranty
does not cover:
Damage occurring during shipment, in either direction.a.
Projector lamps (See Christie’s separate lamp program policy).b.
Damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp c.
supplied by a supplier other than Christie.
Problems caused by combination of the product with non-Christie equipment, such as distribution d.
systems, cameras, video tape recorders, etc., or use of the product with any non-Christie interface
device.
Damage caused by misuse, improper power source, accident, re, ood, lightening, earthquake or e.
other natural disaster.
Damage caused by improper installation/alignment, or by product modication, if by other than a f.
Christie authorized repair service provider.
For LCD projectors, the warranty period specied applies only where the LCD projector is in “normal g.
use.” “Normal use” means the LCD projector is not used more than 8 hours a day, 5 days a week.
For any LCD projector where “normal use” is exceeded, warranty coverage under this warranty
terminates after 6000 hours of operation.
Failure due to normal wear and tear.h.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your
product. Please see the Maintenance section for specic maintenance items as they relate to your
product. Failure to perform maintenance as required, and in accordance with the maintenance
schedule specied by Christie, will void the warranty.
Page 5
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Table of Contents
1. SAFETY
2. INTRODUCTION
2.1 Projector Components ..................................................................................................2-1
2.2 Built-in Keypad .............................................................................................................2-3
2.3 Input/Output (I/O) Panel ...............................................................................................2-4
2.4 Remote Control ............................................................................................................2-5
2.5 LED Status Indicators ...................................................................................................2-7
3. INSTALLATION
3.1 Connect to Computer ...................................................................................................3-1
3.2 Connect to Video Equipment ........................................................................................3-2
3.3 Turn the Projector On ................................................................................................... 3-3
3.4 Turn the Projector Off ................................................................................................... 3-3
3.5 Adjust the Projector Position ........................................................................................3-4
3.6 Calculate Lens Offset ...................................................................................................3-5
3.7 Removing and Installing the Lens ................................................................................3-9
3.8 Ceiling Mount Installation .............................................................................................3-10
3.9 Stacking Installation ......................................................................................................3-11
3.9.1 Adapter Plate Installation .....................................................................................3-11
3.9.2 Stacking ...............................................................................................................3-11
3.9.3 Stacking Multiple Projectors ................................................................................3-12
3.9.4 Stacking Alignment ..............................................................................................3-13
4. OPERATION
4.1 Size and Position Menu ................................................................................................4-2
4.2 Image Settings Menu ....................................................................................................4-7
4.3 Conguration Menu ......................................................................................................4-10
4.4 Lamp Menu ...................................................................................................................4-16
4.5 Status Menu .................................................................................................................4-18
4.6 Input Switching & PIP Menu ......................................................................................... 4-19
4.7 Language Menu ............................................................................................................4-21
4.8 Test Pattern Menu ........................................................................................................ 4-21
4.9 Web User Interface .......................................................................................................4-22
4.9.1 Logging On .......................................................................................................... 4-22
4.9.2 Main Tabbed Page – General .............................................................................4-22
4.9.3 Main Tabbed Page – Status ................................................................................ 4-23
4.9.4 Main Tabbed Page – Lens ..................................................................................4-23
4.9.5 Network ...............................................................................................................4-24
4.9.6 Tools ....................................................................................................................4-26
4.9.7 Administrator Page .............................................................................................. 4-27
4.9.8 About Page ..........................................................................................................4-27
4.10 Christie Presenter ......................................................................................................... 4-28
4.10.1 Connect to the Projector and Download Christie Presenter Software ...............4-28
4.10.2 Install Christie Presenter software .....................................................................4-30
4.10.3 Use Christie Presenter ......................................................................................4-31
4.11 Card Reader Operation ................................................................................................4-36
4.12 Install the Lamp ............................................................................................................4-40
i
Page 6
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Table of Contents
5. TROUBLESHOOTING
6. SPECIFICATIONS
6.1 Inputs ............................................................................................................................6-1
6.2 PIP/PBP Compatibility .................................................................................................. 6-2
6.3 Key Features ................................................................................................................6-3
6.4 List of Components .......................................................................................................6-4
6.5 Optional Accessories ....................................................................................................6-4
6.6 REGULATORY .............................................................................................................6-5
6.7 Declaration of Conformity for EU Countries .................................................................6-7
6.8 Federal Communications Commission (FCC) Warning ................................................ 6-7
6.9 MENU TREE.................................................................................................................6-8
ii
Page 7
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
1. SAFETY
Read through this document in its entirety and understand all warnings and
precautions before attempting to operate the projector.
WARNING
Do not look into the projector lens when the lamp is on. The bright light
y
may result in permanent eye damage.
To reduce the risk of re or electric shock, do not expose this projector to
y
rain or moisture.
Do not open or disassemble the projector as this may cause electric shock.
y
When replacing the lamp, allow the projector to cool, and follow all
y
replacement instructions.
When you turn the projector off, wait 90 seconds for the projector to cool
y
down before you disconnect the projector from power.
Cooling the lamp during the ignition phase may lead to ignition failures.
y
After a successful lamp ignition, keep the lamp burning for at least 15
minutes to maintain lamp life.
When the lamp is approaching the end of its life, the message “Lamp is
y
approaching the end of its useful life in full power operation” appears on
the screen. Change the lamp when the warning message appears.
All installation and maintenance procedures must be performed by a
y
Christie accredited service technician.
Keep all combustible material away from the concentrated light beam of
y
the projector.
Position all cables where they cannot contact hot surfaces or be pulled or
y
tripped over.
Section 1: Safety
1-1
Page 8
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 1: Safety
Always power down the projector and disconnect all power sources before
y
servicing or cleaning.
Use a soft cloth moistened with a mild detergent to clean the display
y
housing.
Disconnect the power plug from the AC outlet if the product is not being
y
used for an extended period of time.
Operate the projector under the following conditions:
y
-
Operating temperature range: 5°C to 35°C
-
Storage temperature range: -10°C to 60°C
-
Humidity range: 5% to 80 % RH (Max.), non condensing
-
Operating altitude: 10,000 ft. maximum
Use only the AC power cord supplied. Do not attempt operation if the AC
y
supply and cord are not within the specied voltage and power range for
your region.
Remove the lens plug from the lens opening in the projector before
y
installing the lens. Retain the lens plug to protect the optical components
from dust and debris during transport.
Do not block the ventilation slots and openings on the projector.
y
Do not use abrasive cleaners, waxes or solvents to clean the projector.
y
Do not allow anything to rest on the power cord.
y
1-2
Page 9
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
2. INTRODUCTION
The product specied in this document is a high brightness, high-resolution
video/graphics 1-chip mercury lamp based projector. The projector is available
in HD and WUXGA resolutions. The projector utilizes Digital Light Processing
(DLP®) technology from Texas Instruments. It is primarily designed for xed
installation markets.
2.1 Projector Components
Section 2: Introduction
Vista frontal
Vista posterior
1
2
3
4
5
6
7
8
9
10
2-1
Page 10
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 2: Introduction
2-2
Ind. Part Name Description
1 Lens door Use the lens door to access the lens module.
2 Front IR Sensor
3 Projection Lens
4 Cooling Air Vents
5 Adjustable Feet Raise or lower the feet to level the projector.
6 LED Status Indicators
7 Rear IR Sensor
Receives signals from the IR remote. Keep the signal
path to the sensor unobstructed for uninterrupted
communication with the projector.
Allows automated lens control and adjustment: vertical
and horizontal offsets, zoom and focus.
Keep these vents unobstructed to prevent the projector
from overheating.
Displays the status of the projector. They are (from left
to right): LAMP 1, LAMP 2, STATUS and PIC MUTE.
Receives signals from the IR remote. Keep the signal
path to the sensor unobstructed for uninterrupted
communication with the projector.
8 Lamp Door (Screws) Use the lamp to access to the lamp module.
9 Built-in Keypad Controls the projector.
Input/Output (I/O)
10
Panel
Connects the projector to external devices.
Page 11
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 2: Introduction
2-3
2.2 Built-in Keypad
1
2
3
4
5 10
Ind. Key Name Description
1 Power Turn the projector on or off.
2 Menu Display menus
3 Auto Automatically optimize image
4 Lens Adjust the lens vertical or horizontal offset setting
5 Focus Adjust focus
6 Exit Return to previous level or exit menus if at top level
Adjust a setting UP or DOWN
7 Arrow Keys
8 Input Select an input for the main or PIP/PBP image
y
Navigate within a menu
y
6
7
8
9
9 Picture Mute Display or blank the video image
10 Zoom Adjust zoom
Page 12
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 2: Introduction
2-4
2.3 Input/Output (I/O) Panel
1 2 3 4 5 6 7 8 9
10 11 12 13 14 1615 17 1918 20
Ind. Connector Name Ind. Connector Name Ind. Connector Name
1 S-Video 2 CVBS 3 Red/Pr
4 Blue/Pb 5 Green/Y 6 RS232 IN
7 Mini USB 8 USB 9 Ethernet
10 Remote 11 Display Port 12 VGA-OUT
13 VGA-IN 14 HDMI-1 15 HDMI-2
16 R 17 G 18 B
19 H/C 20 V
Page 13
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 2: Introduction
2-5
2.4 Remote Control
1
2
3
4
5
6
7
8
9
10
16
17
18
19
20
21
22
23
24
11
12
13
14
15
25
26
27
28
29
Page 14
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 2: Introduction
2-6
Ind. Key Name Description
1 Picture Mute Display or blank the video image
2 Power on Turn projector ON
3 Gamma Adjust mid-range levels
4 Bright Adjust amount of light in the image
5 PIP/PBP Turn PIP/PBP ON/OFF
6 Size Adjust the PIP/PBP size
7 Number Keys Enter a number, such as a channel, value, etc
8 Help Display context-sensitive help
9 Menu Display menus
10 Arrow Keys
11 Test Display a test pattern
12 Auto Automatically optimize image
13 OSD Use to hide or show menus
14 Keystone H Adjust the horizontal keystone
15 Keystone V Adjust the vertical keystone
16 Standby Turn projector OFF
17 Contrast Adjust difference between dark and light
18 Hot-key Select your preset keys quickly
19 Swap Swap the main and PIP/PBP images
20 Layout Adjust the PIP/PBP layout
21 Focus Adjust focus to improve image clarity as desired
22 Zoom Adjust zoom to achieve a desired image size
23 Proj Key
24 Exit Return to previous level or exit menus if at top level
25 Enter
26 Input Select an input for the main or PIP/PBP image
27 Info Display source image information
28 Lens H
29 Lens V
Adjust a setting UP or DOWN
y
Navigate within a menu
y
Change the remote ID. Press Proj Key then a number
between 1 and 9 to assign an ID. Press PROJ then
number 0 to return to the universal remote ID.
Select a highlighted menu item
y
Change or accept a value
y
Horizontal Lens Shift - Adjust the position of the image
horizontally
Vertical Lens Shift - Adjust the position of the image
vertically
Page 15
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 2: Introduction
2-7
2.5 LED Status Indicators
The LED status indicators are located on the rear of the projector.
LAMP 1 LED
y
LED Status Projector State
Failed to strike lamp after 5 attempts (strike attempts will
Red (short blink)
stop).
Lamp has unexpectedly shut down (system goes into
cool down state).
Yellow (no blink)
Green (no blink) Lamp 1 turn ON ok
Green (short blink)
Off Lamp is off
LAMP 2 LED
y
LED Status Projector State
Red (short blink)
Yellow (no blink)
Green (no blink) Lamp 2 turn ON ok
Green (short blink)
Off Lamp is off
Lamp time has expired and lamp should be replaced.
(projector also begins to display the replace lamp On
Screen Display message at startup).
Projector is switching to Lamp 1 (Lamp 2 is off)
(selected by OSD menu “Current Lamp”: 1/ 2/ Both )
Failed to strike lamp after 5 attempts (strike attempts will
stop).
Lamp has unexpectedly shut down (system goes into
cool down state).
Lamp time has expired and lamp should be replaced.
(projector also begins to display the replace lamp OSD
message at startup).
Projector is switching to Lamp 2 (Lamp 1 is off)
(selected by OSD menu “Current Lamp”: 1/ 2/ Both )
Page 16
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 2: Introduction
STATUS LED
y
LED Status Projector State
Off Projector is in OFF state (without AC plug in)
Yellow (no blink) Projector is in standby mode (AC plug in)
Yellow long blink Projector is in startup state
Yellow long blink Projector is in cool down state
Flashing Green/
Yellow
Flashing Red Fan failure
Red (no blink) Over-temperature
Green (blink very
quickly)
Green (no blink) Projector is powered up and operating normally
PICTURE MUTE LED
y
LED Status Projector State
Green Picture mute is off – image is displayed
Yellow (no blink) Picture mute is on – image is black
Projector is in ash update state
Projector communications (Read/Write EEPROM)
2-8
Page 17
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
3. INSTALLATION
mo lex
MOLEX
3.1 Connect to Computer
Desktop Laptop
Section 3: Installation
Ind. Connector Name Ind. Connector Name Ind. Connector Name
1 VGA out Cable 2 VGA in Cable 3 RS232 Cable
Mini USB to USB A Type
4
Cable
7 HDMI to DVI Cable 8 Power Cord 9 Displayport Cable
NOTE:
The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
4 69
71 82 3
5
WiFi USB Dongle or thumb
5
drive
6 Network Cable
3-1
Page 18
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-2
3.2 Connect to Video Equipment
Component video output equipmentDVD player Video cassette recorder
4
1
2 9
3
6
8
4
7
5
Ind. Connector Name Ind. Connector Name Ind. Connector Name
1
S-Video Cable
3 RCA Component
4
Cable
7
VGA in Cable
NOTE:
The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
2
Composite Video Cable
15-Pin to 3 RCA Component/
5
HDTV Adaptor
8
RCA-BNC Cable
3
HDMI Cable
6
VGA to RGB SCART
9
Power Cord
Page 19
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-3
3.3 Turn the Projector On
1 2 3 4 5 6 7 8 9
10
10
10
10
10
1 2 3 4 5 6 7 8 9
10
10
Ensure that the power cord and signal cable are securely connected. The 1.
Power button on the built in keypad is illuminated.
Turn on the lamp by pressing 2.
the built-in keypad.
with a long blink.
The startup screen displays in approximately 10 seconds.
Turn on the source. Select Input Key on the remote control to select 3.
an input source (VGA, BNC, HDMI1, HDMI2, Component, S-Video or
Composite Video).
The projector detects the source you selected and displays the image.4.
NOTE:
The rst time the projector is used, the preferred language may be selected from the main menu after the startup screen is
displayed.
Status LED
The STATUS LED is yellow and LAMP LED is green
“ ”
on the remote control or press
“ ”
Power on
on
3.4 Turn the Projector Off
Power on
“ ”
Press 1.
on the built-in keypad or on the remote control to turn off the
Input Key
projector. A warning message will appear on the displayed image.
“ ”
Press 2.
again to conrm your selection. If you do not press
“ ”
again,
the warning message will disappear after 10 seconds.
Page 20
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-4
20°
20°
360°
3.5 Adjust the Projector Position
When you select a position for the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Follow these general guidelines:
Position the projector on a at surface at a right angle to the screen. The
y
projector (with the standard lens) must be at least 3 feet (0.9m) from the
projection screen.
Position the projector to the desired distance from the screen. The
y
distance from the lens of the projector to the screen, the zoom setting, and
the video format determine the size of the projected image.
For the xed short lens, the image exits at a default angle. However, the
y
lens shift feature makes the image offset variable.
Lens throw ratio:
y
-
Lens 0.8:1 Fixed Short (Zero offset)
-
Lens 1.2-1.5:1 Fixed Short
-
Lens 1.5-2.0:1 Zoom
-
Lens 2.0-4.0:1 Zoom
-
Lens 4.0-7.0:1 Long Zoom
Do not roll the projector more than 20 degrees from side to side.
y
Do not put the projector on either side to project an image.
y
360 degree operation (alone the widest axis)
y
Page 21
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-5
3.6 Calculate Lens Offset
The vertical image offset (shift) ranges for the projector are +120%/-40%
y
(WUXGA) and +134%/-40% (HD). Offset is +720 pixels for both WUXGA
and HD. The horizontal image offset is +/-20% (+/- 192 pixels).
NOTE:
The 0.8:1 lens is the only exception and must be used on axis.
The method for calculating lens offset complies with Industry standards.
y
Example for Vertical lens offset:
-
At 0% offset (or on axis), the center of the image is on the lens center,
so that half of the image appears above and half appears below the
lens center.
-
At +100% offset, all (or 100%) of the image will appear above the lens
center.
-
The % offset is calculated as the ratio of the number of pixels shifted
up/down to half the image size. Examples for WUXGA:
Shifting up 600 pixels gives offset of 600/600 * 100% = 100%
`
Shifting down 600 pixels gives offset of -600/600 * 100% = -100%
`
Shifting up 720 pixels gives offset of 720/600 * 100% = 120%
`
Shifting up 240 pixels gives offset of 240/600 * 100% = 40%
`
WUXGA Projectors:
Vertical Image Offset: 0% Offset (WUXGA)
600 pixels
above lens
center.
600 pixels
below lens
center.
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
Lens center
Page 22
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-6
Vertical Image Offset: 120% Offset (WUXGA)
720 pixels
of shift
above lens
center.
Vertical Image Offset: -40% Offset (WUXGA)
Lens center
Image has been offset 720 pixels above lens
center, so the center of the image is now 720
pixels above where the center of the image
was at 0% offset (or lens center).
The offset is
+720/600 * 100% = +120%.
Image has been offset 240 pixels below lens
center, so the image has an offset of
-240/600 * 100% = -40%
240 pixels
of shift
below lens
center.
Total of
840 pixels
(600+240)
of display
are below
lens center.
Lens center
Page 23
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-7
HD Projectors:
Vertical Image Offset: 0% Offset (HD)
540 pixels
above lens
center.
540 pixels
below lens
center.
Lens center
Vertical Image Offset: 134% Offset (HD)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
720 pixels
of shift
above lens
center.
Image has been offset 720 pixels above lens
center, so the center of the image is now 720
pixels above where the center of the image
was at 0% offset (or lens center).
The offset is
+720/540 * 100% = +134%.
Lens center
Page 24
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-8
Vertical Image Offset: -40% Offset (HD)
Image has been offset 216 pixels below lens
center, so the image has an offset of
-216/540 * 100% = -40%
216 pixels
of shift
below lens
center.
Total of
756 pixels
(540+216)
of display
are below
lens center.
Lens center
Horizontal Image Offset: +/-20% Offset
-192 pixels +192 pixels1920 pixels
Lens center
Image has been offset 192 pixels
left or right of lens center.
The image has an offset of
+192/960 * 100% = +20%, or
-192/960 * 100% = -20%
Page 25
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-9
3.7 Removing and Installing the Lens
When handling the projector after lens installation, make sure the front lens cap is
placed on the lens to protect the lens surface from potential damage. When carrying
or moving the projector, do not handle by the lens. This may damage the lens, the
chassis or other mechanical parts within the projector.
Center the lens:1. Ensure that the lens is at or near its center position. Attempting to
remove the lens when at a large offset may cause damage to the lens assembly. Center
the lens while the projector is switched on by pressing the lens horizontal or vertical
button and then pressing Enter.
Turn Off the projector:2. Turn the projector OFF and disconnect the power cord.
Allow the projector to cool down to Standby mode before replacing the lens.3.
Remove the lens:4. Push and open the lens door located on the top-front of the projector.
Push the release lever up to release the lock. Remove the lens through the front of the 5.
projector.
Remove the rear lens cap from the lens. Keep the front lens cap on the lens to protect it 6.
during installation.
Install the new lens:7. Align the lens interface plate with the lens mount. Fully insert the
assembly straight into the lens mount without turning.
Push the release lever down to lock the lens in place.
Lower the Lens Door and slide back into the secured position. 8.
Page 26
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-10
3.8 Ceiling Mount Installation
The projector can be inverted and suspended from the ceiling using a specially
designed ceiling mount xture. For more information, contact your dealer.
Use only the Christie approved ceiling mount kit (133-106108-02) designed
y
for your projector.
When not mounted properly, the projector may fall, causing hazards or
y
injury. The warranty on this projector does not cover any damage caused
by the use of any non-recommended ceiling mount kit or installation of the
ceiling mount kit in an improper location.
Refer to the installation instructions and safety guidelines provided in the
y
kit.
Page 27
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-11
3.9 Stacking Installation
3.9.1 Adapter Plate Installation
When stacking E Series projectors, an adapter plate is required to install the E
Series unit into the stacking frame.
Turn the projector OFF and disconnect the AC power cord after the cooling 1.
fans have stopped.
Place the projector top-side down on a clean and at surface.2.
Line up the mounting holes of the adapter plate (133-107109-02) with the 3.
mounting holes on the baseplate of the projector.
Secure the adapter plate with 4 M6x25 athead screws. Torque to 41 in-lb.4.
Adapter Plate Attachments
3.9.2 Stacking
The E Series projectors can be stacked up to a maximum of 3 projectors high
using the Christie stacking frame (118-100107-01).
Bottom View
Mounting
All attachment
points to be
secured
Description
1) Base Plate
2) Locking pin
3) Cable Tie-off Frame
4) Stacjing Leg
5) Locking Nut
6) Knob
+/- Roll
+/- Pitch
Frame Weight = 50 Ibs (22.68 kg)
Adapter Plate Weight = 3.26 Ibs (1.48 kg)
Projector Weight = 43 Ibs (19.50 kg)
Lens Weight (up to) = 5.43 Ibs (2.46 kg)
Up to = 101.69 Ibs (46.12 kg)
(per projector and frame)
+/- Yaw
Page 28
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-12
Install the adapter plate on the E Series projector (described in 3.9.1) before
mounting to the stacking frame.
Make sure the pitch is to its maximum, prior to placing the projector from 1.
the front.
Place the projector into the stacking frame.2.
NOTE: There are two ways of placing the projector into the stacking frame: from the top or from the
front.
Make sure the bottom base plate of the frame is aligned with the projector.3.
Use a 6 mm Allen key to tighten the (6) M8 bolts securing the base plate to 4.
the bottom of the stacker adapter plate.
3.9.3 Stacking Multiple Projectors
NOTE: The projectors can be stacked and hoisted in either an upright or inverted positions.
With one person positioned on each side of 1.
the stacking frame, lift the top stacking frame
onto the bottom stacking frame, aligning all
four stacking legs between the frames.
NOTE: Remove the locking pin from each stacking leg prior to alignment
and ensure the four stacking legs are fully seated on the lower stacking
frame.
DANGER
Step 2 is a critical safety procedure
that MUST be observed. Failure to
engage the locking pin may cause
the projectors to separate, resulting in
possible injury or death.
Stacking Frame Attachments
1450.50 mm
980.00 mm
Page 29
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 3: Installation
3-13
Insert the locking pin through the holes in the stacking legs. Make sure 2.
each pin is fully inserted.
NOTE: The steel ball on the end of the pin keeps the pin from releasing inadvertently.
Steel Ball
Hole
Pin
Inserted
Pin
Stacking
Leg
Press botton to
remove or install
the pin
When required, repeat steps 1 and 2 for the third projector in the stack.3.
3.9.4 Stacking Alignment
Stacked projectors must be correctly aligned to one another so the resulting
display is optimized. If hoisting the stack, do so rst and then align. To align
the image, use pitch, yaw, or roll. Prior to aligning the image, turn the locking
nut to unlock then use the knob to adjust the image.
NOTE: Ensure to lock the locking nut to maintain the image adjustment.
Pitch
Adjustment moves the
+/- Roll
+/- Pitch
Note: If the projector is parallel to the screen, some keystone will
be introduced with pitch and yaw adjustment.
+/- Yaw
image up and down
Roll
Rotates the image clockwise
and counter-clockwise
Pitch
Adjustment moves the
image left and right
KNOB
LOCKING
NUT
Page 30
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
4. OPERATION
The projector has multilingual On-Screen Display (OSD) menus that allow you
to make image adjustments and change a variety of settings.
Most of the projector controls are accessed from within the projector menu •
system. There are several groups of related functions, with each group
selectable from the Main menu as shown below. Press the MENU button on
the remote control or on the built-in keypad on the rear of the projector to
display the main menu.
Use the arrow keys to navigate within the menu and adjust a setting up or •
down.
Press ENTER to select a highlighted menu item or use it to change or •
accept a value.
Select the next item that you want to adjust in the menu and adjust it as •
described above.
Press EXIT to return to the previous menu or exit menus if at top level.•
Section 4: Operation
4-1
Page 31
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-2
4.1 Size and Position Menu
Size Presets
Display an image with the detected size, or resize the image by maximizing
either the height, width or both, or resize to the maximum size possible while
keeping the original aspect ratio.
Auto:
y
y
y
y
y
y
y
Overscan
Remove noise around the image. The ZOOM range can be from 50% to 400%
Pixel Track
Analog RGB signals only. Steady ickering or several soft vertical stripes
or bands across the entire image indicates poor pixel tracking. Proper pixel
tracking ensures that the image quality is consistent across the screen, the
aspect ratio is maintained, and that the pixel phase can be optimized.
Display with the detected size.
Native: Display in its native resolution.
4:3: Retain 4:3 aspect ratio.
Letterbox: Display with the black borders on the top and bottom.
Full Size: Fill the screen (regardless of the source).
Full Width: Fill display width and keep aspect ratio.
Full Height: Fill display height and keep aspect ratio.
Page 32
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-3
Pixel Phase
Analog RGB signals only. Adjust pixel phase when the image still shows
shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the
phase of the pixel-sampling clock relative to the incoming signal.
Horz Position
Move the image right or left within the area of available pixels.
Vert Position
Move the image up or down within the area of available pixels.
Digital Horz Zoom
Change the size of projector's display area horizontally. If the display area
has been resized by this setting, it can be moved by changing the Digital Horz
Shift and Digital Vert Shift settings.
Digital Vert Zoom
Change the size of projector's display area vertically. If the display area has
been resized by this setting, it can be moved by changing the Digital Horz
Shift and Digital Vert Shift settings.
Digital Horz Shift
Move the display area horizontally if its size has been changed by the Digital
Zoom setting.
Digital Vert Shift
Move the display area vertically if its size has been changed by the Digital
Zoom setting.
Geometry Correction
The "Geometry Correction" can be controlled with the options in the dropdown list: "Off/Basic" when optional Dual Processor Warp Module is not
installed, and "Off/Basic/Curve/Rotate" when optional Dual Processor Warp
Module is installed.
Geometry Correction Feature Compatibility
Warp Function 4-Corner
4-Corner --
Curved
Surface(2x2)
Keystone
Pincushion
and Barrel
Rotation
P
P
P
P
Curved
Surface(2x2)
Keystone
P P P P
-- X X X
X --
X
X X X --
P
Pincushion
and Barrel
P
-- X
Rotation
X
Page 33
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-4
Off: No Geometric correction is applied to the image.
y
Horz Keystone: Adjust the keystone horizontally and make a more square
y
image. Horizontal keystone is used to correct a keystoned image shape
in which the left and right borders of the image are unequal in length, and
the top and bottom are slanted to one of the sides. This is intended for use
with horizontally on-axis applications. For horizontally offset applications,
you must use 4 Corner correction using the optional Dual Processor Warp
Module.
9%
9%
17%
Vert Keystone: Adjust the keystone vertically and make a more square
y
17%
image. Vertical keystone is used to correct a keystoned image shape in
which the left and right borders of the image are unequal in length, and
the top and bottom are slanted to one of the sides. This is intended for use
with horizontally on-axis applications. For horizontally offset applications,
you must use 4 Corner correction using the optional Dual Processor Warp
Module.
5%
3%
Horz Pincushion: Adjust the pincushion horizontally and make a more
y
5%
3%
square image.
11%
Vert Pincushion:
y
Adjust the pincushion vertically and make a more square
6%
image.
8% 8%
Page 34
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-5
Pincushion/Barrel: Allow for correction for slight curved distortion from the
y
lens or projection surface.
8%
9%
4%
4-Corner: Allow the image to be squeezed to t an area dened by moving
y
9%
each of the four corners’ x and y position.
1 2
8% 8%
8
7%
7%
7
8% 8%
6 5
Curve: Allow for symmetrical correction of a constant radius horizontal
y
Ind. Description
1 Top Left Horz adjust.
3
2 Top Right Horz adjust.
7%
7%
3 Top Right Vert adjust.
4 Bottom Right Vert adjust.
5 Bottom Right Horz adjust.
4
6 Bottom Left Horz adjust.
7 Bottom Left Vert adjust.
8 Top Left Vert adjust.
or vertical curve by modifying the top and bottom of the image only.
Compound curves are not supported. Projector must be mounted
perpendicular to the chord of the curve within the offset limitation of the
lens used (ideally on axis). No tilt correction.
11% 11%
8% 8%
Page 35
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-6
Rotation: Allow an image to be rotated – most commonly to level the
y
image. While the image is rotated, the software can crop any content that
begins to fall off the panel. The function will not automatically scale the
image down to prevent cropping. If scaling is required, the digital zoom
function can be used, independently of the rotation function.
Auto Image
Force the projector to reacquire and lock to the input signal. This is useful
when signal quality is marginal. “Normal mode” can support all of the 4:3 input
sources.
“Wide mode” can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (example
1400 x 1050), perform Auto Image using “normal mode”.
±8°
Page 36
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-7
4.2 Image Settings Menu
Brightness
Adjust the intensity of the image.
Contrast
Adjust the degree of difference between the lightest and darkest parts of the
picture and change the amount of black and white in the image.
Color Space
Select a color space that has been specically tuned for the input signal.
Useful only for analog signals and certain digital sources.
Detail
Select the edge clarity of the image.
Video Options
This function is used with video sources only.
Color: Adjust a video image from black and white to fully saturated color.
y
The color setting applies to video sources only.
Tint: Adjust the red-green color balance in the image of NTSC video
y
images. The tint setting applies to NTSC video sources only.
Noise Reduction: Reduce temporal or spatial noise in the image.
y
Flesh Tone Correction: Control the amount of esh tone correction applied
y
to the image.
Page 37
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-8
Video Black Level: Analyze the current input image and calculate an offset
y
value which is then added to the analog to digital converter black level
value. This ensures optimum black level for each analog source.
Detect Film: Control lm mode detection and determine whether the
y
original source of the input video was lm or video.
Closed Captions: Control closed caption display while audio is not muted.
y
If this setting is not off, audio is not muted, the source is NTSC and
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
Input Levels
VGA / Component signals only.
Adjust the gain of the red, green, or blue channel of the image. It will affect
y
the white.
Adjust the offset of the red, green, or blue channel of the image. It will
y
affect the black and white.
Sync Threshold: (progressive signals only) If a hardware device, such as a
y
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Picture Settings
Optimize the projector for displaying images under certain conditions, such
as presentation, video, bright, whiteboard, blackboard, beige wall and user-
denable preset. It will affect Gamma, Sharpness,White Peaking, Overscan,
Brightness, Contrast, Color, Tint, Red Gain, Green Gain, Blue Gain, Red
Offset, Green Offset, Blue Offset.
Save to User
Adjust the image settings and select Save to User as a picture setting. You
can recall these settings in the future by selecting the User in the Picture
Settings menu. The setting of Brightness, Contrast, Color, Tint, Red Gain,
Green Gain, Blue Gain, Red Offset, Green Offset, Blue Offset, Color Temp,
Gamma, Detail, BrilliantColor , White Peaking and Overscan will be saved.
DynamicBlack™
Select the check box to constantly adjust the aperture based on the amount of
black in the current scene.
Image Freeze
Pause the screen image.
Advanced Image Settings
Gamma: Select the appropriate gamma from Video, Film, Bright, and CRT.
y
BrilliantColor™: Produce an expanded on-screen color spectrum that
y
delivers enhanced color saturation for bright, true-to-life images.
Page 38
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-9
White Peaking: (video source only) Increase the brightness of whites that
y
are near 100%.
Color Temperature: Change the intensity of the colors. Select a listed
y
relative warmth value.
Edge Enhancement: Apply the edge enhancement process.
y
Page 39
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-10
4.3 Conguration Menu
Language
Allows you to select an available language for the OSD display, from English,
French, German, Italian, Spanish, Chinese(simplied), Japanese, Korean, and
Russian.
Lens Settings
Focus and Zoom: Adjust the focus and zoom the image in or out.
y
Lens Shift: Shift the lens up and down or left and right.
y
Lock Lens Motors: Select this function to prevent all lens motors from
y
moving. It will disable the Zoom, Focus, Horizontal and Vertical Position
settings, effectively locking out any changes and overriding all other lens
features. This is particularly useful to prevent accidental lens position
changes in multi-projector installations.
Lens Calibration: Calibrate the lens center
y
Ceiling Mount
Turn the image upside down for ceiling-mounted projection.
Rear Projection
Reverse the image so you can project from behind a translucent screen.
Page 40
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-11
Menu Preferences
Menu Horz Position: Change the horizontal position of the OSD.
y
Menu Vert Position: Change the vertical position of the OSD.
y
Show Messages: Display status messages on the screen.
y
Menu Transparency: Change OSD menu background to be transparent.
y
NOTE:
As the value increases, more of the image behind the menu is visible.
Splash Screen: Choose which splash screen is to be used.
y
PIN Protect: The PIN (personal identication number) feature allows you
y
to password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image.
Change PIN: Allows you to change the PIN.
y
Power Management
Standby Mode: The projector is in standby mode when connected to AC
y
power. (<0.5W)
AC Power On: The projector automatically turns on when electrical power
y
is connected.
Auto Shutdown: Automatically turns the projector off after no signals are
y
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
Sleep Timer: Allows the projector to automatically power off after it has
y
been on for a specied amount of time.
High Altitude
Set high altitude mode ON/OFF. When ON, the fan will operate at high speed
to ensure sufcient air ow for high altitudes.
Communications
Network: Allow you to setup network settings.
y
DHCP: Turn the DHCP ON/OFF. IP Address: Assign Network IP Address. Subnet Mask: Assign Network Subnet Mask. Default Gateway: Assign Network Default Gateway. Host Name: Display the host name. MAC Address: Displays network MAC Address value. Show Network Messages: Turn network messages ON/OFF. Restart Network: Restart the network. Network Factory Reset: Perform factory reset on the network settings. -
The Projector Name, LAN IP, WLAN IP, and SNMP settings will be
reset.
Page 41
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-12
P
r
o
j.
1
,1
P
r
o
j.
1
,
2
P
r
o
j. 2
,1
P
r
o
j. 2
,
2
Proj. 1,1 Proj. 1,2
Proj. 2,1 Proj. 2,2
Baud Rate: Select the serial port and baud rate.
y
Serial Port Echo: Control whether the serial port echoes characters.
y
Projector Address: Set the projector address (0-9). The projector will
y
respond to IR remotes set either at the same address as the projector or to
IR remotes set to address 0.
Image Blending
Adjust blend widths and settings to left, right, top and/or bottom sides to create
a seamless multi-projector stitched image. (Available only when optional Dual
Processor Warp Module is installed.)
What is a Blend?
In simple terms, a blend appears as a gradient strip along an edge of a
projected image. It is darkest along the extreme edge of the image, and
lightens nearer to the rest of the image(see below).
How are Blends used?
In multiple-projector wall, complementary blends between neighboring images
can compensate for the extra “brightness” or intensity where these edges
overlap. By controlling blend width and other properties, you can achieve
uniformity across the group of images. Visible overlaps will disappear, as
shown below
Overlap
With edge blending:
Blend
Overlap
Image
Image
Blending regions can be dened on all sides – left, right, top and bottom. The
same gamma curve is used for all blending regions.
Blend
Page 42
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-13
Color Matching
You may require a unique color gamut (range) for a single projector or
application, or you may need to precisely match colors across multiple
adjacent displays. Use Color Matching by Meter Adjustment or by Manual
Adjustment to dene the precise hue of each primary color component (red,
green, blue and white).
The x/y coordinates for each color dene its location on the standard CIE
chromaticity graph. Changing either or both of these numbers will change
the hue of the color, and modify the range of possible colors. For example,
changing the x/y coordinates for red may move the color closer to orange
or closer to violet, which will in turn affect all displayed colors having a red
component. Adjust the slide bars or enter new specic coordinates as desired
to dene or change the color gamuts needed for your environment and
applications.
Enable the selected method (Meter or Manual Adjustment)– this will
automatically disable the other method. For both methods, if Auto Test Pattern
is enabled, the solid colored test pattern will be displayed according to the
menu item on which you are positioned.
Meter Adjustment
y
Using a color meter, enter the current x and y co-ordinates of Red, 1.
Green, Blue and White for the projector image into the Measured Data
menu. This is the reference point for the projector. The default values
in the menu are based on the average for all projectors.
After measuring the values for all the projectors to be matched, 2.
calculate the target values.
Enter the target values for x, y and gain for each color into the Target 3.
Data menu.
Page 43
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-14
Green
Red
Blue
Manual Adjustment
y
Measured Data
Target Data
Adjust color slide bars and judge image color by eye or meter. A user-1.
dened color “adjustment” can be applied.
Use this submenu if you do not have specic color coordinates in 2.
mind and will judge color performance by eye or meter. As for Meter
Adjustment, each color control actually denes new x/y coordinates for
that color and changes its hue. The main colors (red part of red, green
part of green and blue part of blue) adjust the intensity of that color
component, while the modifying colors (e.g. green part of red and blue
part of red) modify the x and y value and change the hue of that color.
At the same time the main colors also are used to control the color of
the white point.
Hot-Key Settings
Assign a different function to the hot-key on the remote control by highlighting
the function in the list and pressing ENTER. Choose a function that does
not already have a dedicated button, and assign the hot-key to that function,
allowing you to quickly and easily use the chosen function.
Service
Projector Info: Display current projector settings (read-only).
y
Factory Reset: Restore all settings to their default value. It will not reset
y
network but it will reset RS232.
Test Pattern: Choose the desired internal test pattern to display, or select
y
OFF to turn off a test pattern.
Color wheel Index (2x): Set Color wheel index to Speed 2X. This setting
y
only needs to be used when the Main Board is changed, and should be
Page 44
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-15
adjusted to optimize picture quality.
Color wheel Index (3x): Set Color wheel index to Speed 3X. This setting
y
only needs to be used when the Main Board is changed, and should be
adjusted to optimize picture quality.
Error log: Show the projector error log for debug.
y
Mode Adjustment: Fine tune the H and V start position for a signal in the
y
EDID timing table and record the values in the system to override the
timing table. The settings must be “Saved to Record” before exiting the
menu, or they will be lost. To revert to original timing table settings, each
setting must be manually cleared. Factory Defaults will not clear these
override settings.
Page 45
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-16
4.4 Lamp Menu
Lamp Mode
Select Constant Power or Constant Intensity mode.
Constant Power
Set the value of the lamp power (in Watts).
Constant Intensity
Set the value for the Constant Intensity to maintain constant brightness. A light
sensor is used to monitor the light level and will apply more power as the lamp
brightness decays naturally over time until it reaches maximum power. The
light sensor needs to be calibrated when you replace a lamp or "Reset Lamp
Hours".
Current Lamp
Select which lamp(s) is in use.
NOTE:
A 120 second timed lockout is applied after changing modes before you can change it again.
Eco Mode
Set Eco mode ON, OFF, Auto or assign a lamp to Eco mode. When Eco Mode
is enabled, the projector will switch to single lamp mode, adjust to the lowest
fan speed and switch the lamp power to the minimum setting.
Lamp Auto Switch
Control when the projector switches lamps. Options include: on failure only, at
Page 46
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-17
power-up, or after a set number of hours.
Lamp Auto Switch Time
Set the number of hours for Lamp Auto Switch.
For example:
Lamp conditions: lamp 1 = 50 hours, lamp 2 = 60 hours.1.
Set the current lamp to lamp 1 - the lamp with the lower lamp hour 2.
usage.
Set the Lamp Auto Switch to After (N) hours and the Lamp Auto 3.
Switch Time to 100 hours.
When lamp 1 reaches 150 hours, projector will auto switch to lamp 2.4.
When lamp 2 reaches 160 hours, projector will auto switch to lamp 1.5.
Lamp Info
Display current lamp(s) settings (read-only).
Lamp Life Settings
Set the number of hours for the lamp life warning. At every startup, the lamp
hours are checked. If they exceed this value, a lamp replace message will
appear.
Reset Lamp Hours
Reset the lamp used hours counter to zero. Do this after changing the lamp.
Light Sensor
Calibrate the Light Sensor for use with the Constant Intensity lamp mode,
which allows the projector to be set for constant brightness. If the Light Sensor
has not been calibrated, Constant Intensity mode will be disabled. Light
Sensor calibration should be repeated when new lamps are installed.
Page 47
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-18
4.5 Status Menu
The read-only Status menu lists a variety of details about the standard and
optional components currently detected in the projector.
Page 48
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-19
4.6 Input Switching & PIP Menu
NOTE:
Reference the compatibility table found in Section 6.2.
Main Input
From the list of active inputs, select one to be used as the main image.
PIP/PBP Input
From the list of active inputs, select one to be used as the PIP/PBP.
PIP/PBP Enable
Toggle between displaying two sources at once (Main and PIP/PBP images)
or one source only. The check box turns the PIP/PBP source ON and OFF.
Swap
Change the main image to PIP/PBP, and the PIP/PBP to main image.
Swapping is available only when PIP/PBP is enabled.
Size
Select the PIP/PBP size to small, medium or large.
Layout
Set the location of the PIP/PBP image on the screen.
Page 49
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-20
P
P
P
P
P
P
P
P
P
P
P
P
PPP
PPP
P
P
P
PPP
NOTE:
PIP/PBP layout and size table as described below.
P : indicates primary source region (lighter color).
* : Both source regions are the same size.
PIP/PBP Layout
PIP/PBP Size
Small Medium Large
PBP, Main left
PBP, Main Top
PBP, Main Right
PBP, Main Bottom
*
*
*
*
PIP-Bottom Right
PIP-Bottom Left
PIP-Top Left
PIP-Top Right
Timing Detection
Select timing detection mode to wide or normal. It is used to support additional
PC timings. When the projected picture is not completed, this function is used
to adjust the picture. “Normal mode” can support all of the 4:3 input sources.
“Wide mode” can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (example
1400 x 1050), perform Auto Image using “normal mode”.
Source Info
Display current source settings (read-only).
Enable Source Hot-Key
Toggle the check box to enable or disable the main source hot-key.
Source Hot-Key
Allows you to assign a different source to the hot-key. Highlight an input and
press ENTER to choose a different one.
Page 50
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-21
Input Key
Use it to list all of the sources or change the sources.
4.7 Language Menu
Allows you to select an available language for the OSD display.
4.8 Test Pattern Menu
Choose the desired internal test pattern to display, or select OFF to turn off a
test pattern.
OFF
y
Black
y
White
y
Checkerboard
y
Grid
y
Color Bars
y
Page 51
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-22
4.9 Web User Interface
4.9.1 Logging On
Open your web browser and type the IP address (in the address bar) assigned
to your projector.
1 Select the log in level from the Access type drop-down list
2 Enter the Password in the Password eld
3 Select the appropriate language from the Language drop-down list.
4 Click the Press login button. The Main window appears.
4.9.2 Main Tabbed Page – General
Control Panel
y
Select main source / PIP source, enable/disable PIP/POP, change the
layout / PIP size, swap, and change the test pattern.
Page 52
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-23
Projector Information Panel
y
Check the projector information for power status, Pic mute status, OSD
status, IP address and Mac address.
Switch Panel
Switch the on/off status of power, Pic mute, and OSD.
4.9.3 Main Tabbed Page – Status
Display the current status of lamp info, cooling (fans), version numbers and
signal (source) information
4.9.4 Main Tabbed Page – Lens
Control the focus, lens shift and zoom adjustments for the lens.
Page 53
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-24
4.9.5 Network
SettingsPage
Restart Network
y
Execute a network restart. This will not change any of the network settings.
Network Factory Reset
y
Execute a network factory reset. Network settings will be reset to the
following default values:
Projector Name = Christie@ + Serial Number Show Network Messages = ON LAN Settings: -
Manual IP Address = 192.168.0.100 Subnet Mask = 255.255.255.0 Default Gateway = 192.168.0.100 -
WLAN Settings: -
Enabled -
Page 54
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-25
Start IP = 192.168.1.100 End IP = 192.168.1.120 -
Subnet Mask = 255.255.255.0 Default Gateway = 192.168.1.100 -
SNMP Settings: -
SNMP Read Communication = private Trap IP Address = 0.0.0.0 SMTP IP Address = 0.0.0.0 All other settings are cleared/blanked -
Trap Conguration: -
All items = SNMP Trap + Email -
LAN Panel
y
Enter the IP address, subnet mask, default gateway for the LAN setting
Select if the projector must obtain an automatically assigned IP address through DHCP or if the user will set the address manually.
Enter the IP address, netmask, default gateway and DNS server address for the TCP/IP setting
WLAN Panel
y
Select if Enable or Disable the WLAN function. Enter Start IP, End IP, Subnet Mask, Default Gateway for the WLAN -
setting.
SNMP Panel
y
The E Series SNMP (Simple Network Management Protocol) interface provides network administrators with a common way to manage their
network devices from a single remote location. SNMP allows an
administrator to query a number of devices to see their current status/
conguration. It also allows operators to change conguration values
and congure trap or Email notications to be sent when certain events
occur.(eg. Loss of signal, power state change, etc)
Emails are sent to the mail server congured in the projector
`
settings. Up to 2 user email accounts can be selected. Any
important information regarding the event will be located in the body
content of the email.
SNMP Traps are notications that are sent from the projector. They
`
are only received by a trap receiver (MIB Browser) in the computer.
SNMP Read Community (default setting: private) – this is a plain- text password. This must also be entered in the MIB browser. This
password allows the various settings in the projector to be queried.
Page 55
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-26
SNMP Location (default setting: blank) – This eld can be used as a description to where a projector is located in a building.
SNMP emails sent will specify this location.
Trap IP Address (default setting: 0.0.0.0) – This eld must be lled in to receive Traps from the projector. The Trap IP Address
should be lled in with the IP Address of the computer on which
you would like to view received traps.
Trap Email 1/2 (default setting: Blank) – The Trap Email 1 and 2 -
must be set to an email address that is congured under the mail
server that you will enter in the “SMTP Server IP Address” eld.
Email from Address (default setting: blank) – the “Email from -
Address” that will appear as the source of the SNMP emails.
SMTP Server IP Address (default setting: 0.0.0.0) – Enter your -
mail server’s IP address.
Trap Conguration Panel
y
Set the SNMP actions for the system events. The dropdown options
are: SNMP Trap + Email, Email, SNMP Trap, and Disabled.
4.9.6 Tools
Use the Tools tabbed pages to control “Size & Position”, “Image
Settings”, “Conguration”, “Lamp”, “Input Switching & PIP” and “Test
Pattern”.
Page 56
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-27
4.9.7 Administrator Page
Add or delete a user or change password
4.9.8 About Page
Version Tab
y
View the main rmware version, network rmware version, projector model
name, and projector serial number.
License Tab
y
The license information of the computer program is displayed.
Page 57
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-28
4.10 Christie Presenter
The Christie Presenter application allows a remote desktop from a host PC
to be displayed on the network display through Ethernet, USB, or wireless
transports. It can adapt to different network settings (DHCP, xed IP, and
direct link by USB/Ethernet cable).
Christie Presenter can be downloaded from the Christie website or from the
web page of the projector.
4.10.1 Connect to the Projector and Download Christie Presenter
Software
Connect to the projector using WiFi or Ethernet1.
Ethernet connection: -
Determine the projector’s IP address from the menu Main Menu >
`
Conguration > Communications > LAN
Congure your PC IP address to be on the same network as the
`
projector.
The projector and computer must be connected directly or over the
`
network via Ethernet.
WiFi Wireless connection: -
Insert the WiFi USB dongle (1DWUSB-BGN) into the USB port on
`
the projector input panel.
Insert the WiFi USB dongle
Page 58
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-29
Power on the Projector.
`
Obtain the WiFi Password from the OSD menu Main Menu >
`
Conguration > Communications > WLAN
Connect your PC device to the wireless SSID for the selected
`
projector . Example: “Christie@0112000123”.
Enter the password obtained from the OSD WLAN menu.
`
Page 59
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-30
4.10.2 Install Christie Presenter software
Use a web browser to connect to the projector’s network address (Default 1.
address 192.168.1.100)
Download and install the Christie Presenter Software2.
Congure the Christie Presenter Software. The name entered is used to 3.
identify all computers connected to the projector via the Christie Presenter
software via either wired or wireless connections. The Network Display
Management -> Device Management tab will show all current connections.
Page 60
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-31
4.10.3 Use Christie Presenter
Press the autorun icon in the system tray to pause or play the USB display.1.
After starting the Christie Presenter application, the main window can been 2.
seen (shown below).
Icon Description
Connect and search network display
Stop/start displaying desktop contents to
connected network display
Select display region
Congure Christie Presenter
Manage all connected network displays
Disconnect all connections
Page 61
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-32
Connect and search network display
Click the button 1.
to enter into the connection menu section.
If the IP address of the projector is known, enter the IP address and 2.
click the "Connect" button. If the IP address is not known, click the
"Search" button to search for the projector on the network and select
the projector to which you want to connect. Select the option "Directly"
in order to proceed to the log in interface.
Input “User type” and “Password” in the log-in interface. Select the 3.
display port (the default is full screen).
Page 62
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-33
Select display region
Once the connection is set up, click the button
to select the size of
the projection region: FullScreen, FixedSize, or Alterable.
FullScreen: The default capture mode turns to Full screen when the
y
program is launched. At that time, if screen capture starts, the image of the
whole screen is transferred to a remote network display.
FixedSize: FixedSize mode allows the users to place a frame on the
y
desktop. Only the image enclosed inside the frame is transferred to remote
network display.
Alterable: In Alterable mode the only region captured is the one enclosed
y
by the frame. The region can be enlarged or downsized by dragging the
eight small black squares scattered on eight edges of the frame.
Page 63
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-34
Congure Christie Presenter
Click the button
to congure Christie Presenter for Basic Setting
and Advanced Setting.
Basic Setting: Select language, change the region size of xed size
y
capture mode, and select if notication message popup is allowed.
Advanced Setting: Select the quality of JPEG image, YUV sample format
y
and network port setting. (The "Fixed" port is Port 5900)
Page 64
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-35
Manage all connected network displays
Click the button
to control all the users and all the projectors
connector to the same projector.
Icon Description
Administrator log in.
Normal user log in.
Device is connected.
Device is not connected.
The icon shows the current status and
display position of the local screen on the
network display. Click on the icon to change
the display position. A dialog box will appear.
Click this unlock icon to change the
password. (Password change to target
network display. Only an Administrator user
can change the password.)
No response is expected when this icon is
clicked. If the user is logged in as "Admin",
the key icon can be seen and the Presenter
password can be changed. If the user is
logged in as "Normal", the lock icon can be
seen and the Presenter password can't be
changed.
Disconnect from target network display.
Link for connecting to a target network
display via a webpage.
Page 65
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-36
4.11 Card Reader Operation
There are four operation modes in the Card Reader application:
USB Flash Devices Detection Screen Thumbnail Display Mode Images Display Mode Images Slide Show Mode -
4.11.1 USB Flash Device Detection Screen:
In this mode, the Card Reader application detects any USB ash devices
hot-plug events and displays the ash device icon. When the ash device
is removed from USB, the icon disappears. It is suggested that USB ash
devices should be removed only when the Card Reader is changed to the
USB Flash Devices Detection Screen state.
4.11.2 Thumbnail Display Mode:
Press the Enter key to enter the Thumbnail Display Mode. Different photos
in different folders can be chosen. Press the Menu key to bring up the
Card Reader operation UI.
Page 66
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-37
The user interface is designed to operate the card reader application with
a few keys (Enter/Left/Right/Up/Down).
The following buttons are supported in the user interface:
Previous: Move the selected item left. (Go to previous page when this is
y
the leftmost item)
Next: Move the selected item right. (Go to next page when this is the
y
rightmost item.)
Display: Display the selected image or display the selected folder.
y
Thumbnail: Enter the Thumbnail Display Mode.
y
SlideShow: Enter the Slide Show Mode.
y
NameOrder: Sort les/folders in name order.
y
ExtendOrder: Sort les/folders in extended order.
y
SizeOrder: Sort les/folders in size order.
y
TimeOrder: Sort les/folders in time order.
y
EXIF ON/OFF: Enable/Disable auto image rotate accordingly to EXIF
y
information.
FileName ON/OFF: Enable/Disable lename display in Thumbnail Display
y
Mode.
4.11.3 Image Display Mode:
Press the ENTER key in the Thumbnail Display Mode to enter the Image
Display Mode. Press the SlideShow key to enter the Slide Show Mode.
The Left/Right key is used to display the last/next image in the Image
Display Mode. In the Image Display Mode, press the ENTER key to quit
from the Image Display Mode and enter the Thumbnail Display Mode.
In the Slide Show Mode, press the ENTER key to enter the Image Display
Mode.
The alternative way to display image in the Image Display Mode or Slide
Show Mode is using the operation UI.
The following operations are supported in the operation UI.
Display: Enter the Image Display Mode.
y
Page 67
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-38
Thumbnail: Enter the Thumbnail Display Mode.
y
SlideShow: Enter the Slide Show Mode.
y
Actual Size: Display in actual size of the image.
y
Best Fit: Display the image in best t to the screen.
y
EXIFDisp OFF/On: Enable/Disable EXIF information display.
y
+90deg: Rotate 90 degree.
y
-90deg: Rotate -90 degree.
y
4.11.4 Image Slide Show Mode:
The following operations are supported in the Slide Show Mode operation
UI.
Stop: Stop Slide Show Mode.
y
Next: Display next image.
y
Previous: Display previous image.
y
Delay 3/4/5: Slide Show delay in seconds.
y
Slide Effect: Following modes are supported.
y
o Slide Right o Blocks o RightDown o XLines o Slide Up o Ylines o Repeat ON/OFF: Enable/Disable Slide Show Repeat Mode. -
Page 68
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4-39
When the image cannot be displayed due to memory limitation or cannot
support image format, the specic image is displayed on the center of the
screen.
Page 69
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 4: Operation
4.12 Install the Lamp
The projector automatically detects the lamp life. When the lamp life is
nearing the end of use, you will receive a warning message. When you see
this message, please change the lamp as soon as possible. Make sure the
projector has been cooled down for at least 30 minutes before changing the
lamp.
Note the number of the lamp that needs to be replaced on the 1. “Current Lamp” menu.
Turn off the lamps:2. Turn the projector OFF and disconnect the power cord.
Allow the projector to cool down for at least 30 minutes.3.
Open the lamp door:4. Unscrew the two screws on the lamp door.
Open the lamp door located on the top-rear of the projector.5.
Remove the lamp:6. Loosen the two captive screws securing the lamp.
Lift up the lamp by grasping handle and remove the lamp module slowly and carefully. 7.
4-40
Install the new lamp:8. Replace the lamp with a new one and tighten two screws. Make
sure the lamp is set properly and secure.
Close the lamp door:9. Put the Lamp Door back on and tighten two screws.
Reset the projector:10. Turn the projector ON and use “Reset Lamp Hours” after the lamp
module is replaced.
Recommend calibrating light sensor if using Constant Intensity for lamp mode.11.
Page 70
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
5. TROUBLESHOOTING
If you are unable to resolve an issue using the information provided in this
section, contact your reseller or service center.
Problem Solution
No image appears
y
on-screen
-
Make sure all the cables and power connections are
correctly and securely connected See “Installation”.
-
Check if the lamp is securely installed.
-
Make sure you have removed the lens cap and the
projector is switched ON.
Section 5: Troubleshooting
Partial, scrolling
y
or incorrectly
displayed image
-
Press “AUTO” on control panel or on remote control.
-
If you are using a PC (for Windows 95, 98, 2000, XP,
Windows 7):
1.
2.
3.
4.
Click the
“
My Computer
double - click
“
Select the
Settings” tab.
“
Display”.
” > “
Control Panel” and then
Verify that your display resolution setting is lower
than or equal to WUXGA (1920 × 1200).
“
Click on the
Advanced Properties” button. If the
projector is still not projecting the whole image,
change the monitor display:
4.1 Verify the resolution setting is lower than or equal
to WUXGA (1920 × 1200).
4.2 Select the
“
Change” button under the “Monitor”
tab.
4.3 Click on
“
Show all devices”. Next, select “Standard
monitor types” under the SP box; choose the
resolution mode you need under the “Models”
box.
4.4 Verify that the resolution setting of the monitor
display is lower than or equal to WUXGA (1920 ×
1200).
5-1
Page 71
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 5: Troubleshooting
5-2
Problem Solution
Partial, scrolling
y
or incorrectly
displayed image
-
If you are using a Notebook:
Adjust resolution of the computer.
1.
Press the keys listed below for your notebook
2.
manufacturer to send signal out from notebook to
projector. Example: [Fn]+[F4]
Notebook Brand Function Keys
Acer [Fn]+[F5]
Asus [Fn]+[F8]
Dell [Fn]+[F8]
Gateway [Fn]+[F4]
IBM/Lenovo [Fn]+[F7]
HP/Compaq [Fn]+[F4]
NEC [Fn]+[F3]
Toshiba [Fn]+[F5]
The screen of
y
the Notebook
or PowerBook
computer is not
displaying your
presentation
Image is unstable
y
or ickering
Image has vertical
y
ickering bar
System Preference Display
Arrangement Mirror display
-
Mac Apple
If you experience difculty changing resolutions or your
monitor freezes, restart all equipment including the
projector.
-
If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens
when a second display device is in use. Each of them has
a different method of reactivation. Please refer to your
computer manual for detailed information.
-
Use “Pixel Track” and “Pixel Phase” to correct it.
-
Change the monitor color setting on your computer.
-
Use “Auto Image” to make an adjustment.
-
Check and recongure the display mode of your graphic
card to make it compatible with the projector.
Page 72
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 5: Troubleshooting
5-3
Problem Solution
Image is out of
y
focus
-
Make sure both lens caps (front and back) are removed.
-
Adjust lens focus to t.
-
Make sure the projection screen is between the required
distance.
The image is
y
stretched when
displaying 16:9
DVD title
Image is too small
y
or too large
Lamp burns out or
y
makes a popping
sound
-
When you play anamorphic DVD or 16:9 DVD, the
projector will show the best image when the projector
display mode is set to 16:9 in the OSD.
-
If you play 4:3 format DVD titles, please change the format
to 4:3 in the projector OSD.
-
If the image is still stretched, you will also need to adjust
the aspect ratio by setting the display format as 16:9 (wide)
aspect ratio type on your DVD player.
-
Adjust lens zoom to t.
-
If it does not ll the screen properly, verify that the correct
lens is in use or change the position of the projector.
-
If the lamp burns out, try power cycling the projector. If
the lamp doesn't re or if you hear it make a loud pop, the
projector will not turn on until the lamp module has been
replaced.
Page 73
Page 74
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
6. SPECIFICATIONS
6.1 Inputs
Signal
Resolution
Type
640x480 60 ● ● ● ● ●
640x480 75 ● ● ● ● ●
640x480 85 ● ● ● ● ●
800x600 60 ● ● ● ● ●
800x600 75 ● ● ● ● ●
800x600 85 ● ● ● ● ●
1024x768 60 ● ● ● ● ●
1024x768 75 ● ● ● ● ●
1024x768 85 ● ● ● ● ●
1280x768 60 ● ● ● ● ●
PC
1280x800 50 ● ● ● ● ●
1280x800 60 ● ● ● ● ●
1280x1024 60 ● ● ● ● ●
Frame Rate
(Hz)
HDMI 1 HDMI 2 VGA
Section 6: Specications
Display-
Port
BNC
Compo-
nent
S- video CVBS
1280x1024 75 ● ● ● ● ●
1280x1024 85 ● ● ● ● ●
1400x1050 60 ● ● ● ● ●
1600x1200 60 ● ● ● ● ●
1680x1050 60 ● ● ●
1920x1200RB* 60 ● ● ● ● ●
1920x1200RB* 50 ● ● ● ● ●
NTSC
PAL
NOTE:
NTSC
(M, 4.43)
PAL (B,G,H,I) 50 ● ●
PAL (N) 50 ● ●
PAL (M) 60 ● ●
"RB" means "reduced blanking".
60 ● ●
6-1
Page 75
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
6-2
Signal
Resolution
Type
SECAM SECAM (M) 50 ● ●
Frame Rate
(Hz)
HDMI 1 HDMI 2 VGA
Display-
Port
BNC
Compo-
nent
S- video CVBS
EDTV
HDTV
480p 60 ● ● ● ● ● ●
576p 50 ● ● ● ● ● ●
1080i 60 ● ● ● ● ● ●
720p 50 ● ● ● ● ● ●
720p 60 ● ● ● ● ● ●
1080p 24 ● ● ● ● ● ●
1080p 25 ● ● ● ● ● ●
1080p 30 ● ● ● ● ● ●
1080p 50 ● ● ● ● ● ●
1080p 60 ● ● ● ● ● ●
6.2 PIP/PBP Compatibility
Main
PIP/PBP
HDMI 1 ● - - ● - ● ● ● ● ●
HDMI 2 ● ● ● ●
DisplayPort - ● - - ● - ● ● ● ● ●
VGA - ● - - ● - ● ● ● ● ●
BNC ● - ● ● - ● - - - - -
HDMI 1 HDMI 2
Display-
Port
VGA BNC
Compo-
nent
S-video
Composite
RJ45
USB type
B (mini)
USB
type A
Component - ● - - ● - ● ● ● ● ●
S-video ● - ● ● - ● - - - - -
Composite ● - ● ● - ● - - - - -
RJ45 ● - ● ● - ● - - - - -
USB type B
(mini)
USB type A ● - ● ● - ● - - - - -
● : PIP/PBP combinations are enabled
- : PIP/PBP combinations are disabled
● - ● ● - ● - - - - -
Page 76
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 6: Specications
6-3
6.3 Key Features
HD 0.65
y
Projection lens compatibility:
y
-
-
-
NOTE:
Dynamic aperture enabled (full white to full dark contrast ratio): 5000:1
y
(Nominal)
Dual Processor Warp Module for edge blending and geometric correction.
y
(Optional)
Wireless desktop display using wireless dongle (optional)
y
SNMP traps and e-mail notications
y
Dual mercury lamp illumination with 330W (DWU/DHD675-E) & 350W
y
(DWU/DHD775-E)
10-bit image processor electronics with modular design
y
All video formats can be resized to full screen either horizontally or
y
vertically while maintaining aspect ratio
The projector can be operated using any of the following:
y
-
-
Weight:
y
-
-
Built-In keypad
y
”
1920 × 1080 resolution or WUXGA 0.67” 1920 × 1200 resolution
Horizontal offset ranges: +/-20%
Vertical offset ranges: +120%/-40% (WUXGA) and +134%/-40% (HD)
Exception: 0.8:1 lens must be used on axis.
Measurements are based on industry standards where offset is calculated as a ratio of the number of pixels shifted
up/down to half the image size.
The built-in keypad, an infrared (IR) remote control, a wired remote
control, a PC/device using serial communications (Ethernet or RS232)
A Web page via Ethernet or from a PC/device via a wireless USB
dongle. (Optional)
Maximum product weight (with lens removed): 19.5kg (43lb.)
Maximum shipping weight (includes packaging): 28kg (62lb.)
Page 77
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
6-4
6.4 List of Components
This projector comes with all the items shown below. Check to make sure your
package is complete. Contact your dealer if anything is missing.
IR remote control (133-114117-01)
y
Power cord x 4
y
-
UK/Korea/Russia
-
North America
-
Europe
-
Japan
DVI to HDMI dongle
y
User manual (CD)
y
NOTE:
Due to the difference in applications for each country, some regions may have different accessories.
6.5 Optional Accessories
Ceiling mount (optional accessory) (133-106108-XX)
y
Ceiling mount extension rod (104-101001-XX)
y
Fixed Lens (optional accessory):
y
-
Lens 0.8:1 Fixed Short (Zero offset) (133-100102-XX)
Zoom Lenses x 4 (optional accessory):
y
-
Lens 1.2-1.5:1 Fixed Short (133-101103-XX)
-
Lens 1.5-2.0:1 Zoom (133-102104-XX)
-
Lens 2.0-4.0:1 Zoom (133-103105-XX)
-
Lens 4.0-7.0:1 Long Zoom (133-104106-XX)
1DWUSB-BGN / Wireless dongle (optional accessory) (133-113106-XX)
y
Dual Processor Warp Module (optional accessory) (133-111104-XX)
y
Adapter Plate Stacker (optional accessory)(133-107109-02)
y
Stacking Frame (optional accessory)(118-100107-01)
y
E Series Color Wheel (Color) (optional accessory)(003-003411-01)
y
Page 78
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 6: Specications
6-5
6.6 REGULATORY
Safety
y
-
CAN/CSA C22.2 No. 60950-1
-
UL 60950-1
-
IEC 60950-1
-
EN60950
Electro-Magnetic Compatibility
y
Emissions
-
FCC CFR47, Part 15, Subpart B/ICES-003/ANSI C63.4, Class A –
Unintentional Radiators
-
AS/NZS CISPR 22/EN55022 Class A - Information Technology
Equipment
-
EN 61000-3-2
-
EN 61000-3-3
Immunity
-
EN55024 EMC Requirements - Information Technology Equipment
-
IEC 61000-4-2
-
IEC 61000-4-3
-
IEC 61000-4-4,
-
IEC 61000-4-5
-
IEC 61000-4-6
-
IEC 61000-4-8
-
IEC 61000-4-11
Environmental
y
-
The product conforms to:
-
EU Directive (2002/95/EC) on the restriction of the use of certain
hazardous substances (RoHS) in electrical and electronic equipment
and the applicable ofcial amendment(s).
-
EU Regulation (EC) No. 1907/2006 on the registration, evaluation,
authorization and restriction of chemicals (REACH) and the applicable
ofcial amendment(s).
-
EU Directive (2002/96/EC) on waste and electrical and electronic
equipment (WEEE) and the applicable ofcial amendment(s).
-
China Ministry of Information Industry Order No.39 (02/2006) on the
control of pollution caused by electronic information products, the
hazardous substances concentration limits (SJ/T11363-2006), and the
applicable product marking requirement (SJ/T11364-2006).
Page 79
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
6-6
Marking
y
-
This product shall conform to all relevant Canadian, US, and European
directives, standards, safety, health and environmental concerns and
bear the following markings at product launch:
UL
`
CE
`
RoHS
`
WEEE
`
-
Future product markings to include International Certications: CCC,
KC, PSE, c-tick, Gost-R, South Africa
-
International packaging recycling mark requirements:
EU Directive (2002/96/EC) on waste and electrical and electronic
`
equipment (WEEE);
EU Directive (94/62/EC) on packaging and packaging waste;
`
China packaging recycling mark standard (GB18455-2001).
`
Page 80
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 6: Specications
6-7
6.7 Declaration of Conformity for EU Countries
EMC Directive 2004/108/EC (including amendments)
y
Low Voltage Directive 2006/95/EC
y
Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
y
6.8 Federal Communications Commission (FCC) Warning
WARNING
A shielded-type power cord is required in order to meet FCC emission
y
limits and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used.
Use only shielded signal cables to connect I/O devices to this equipment.
y
Page 81
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
6-8
6.9 MENU TREE
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
Auto
Native
4:3
Letterbox
Full Size
Full Width
Full Height
Off
Zoom
Crop
Pixel Track 0 - 100 50
Pixel Phase 0 - 100 50
Horz Position 0 - 100 50
Vert Position 0 - 100 50
Digital Horz Zoom 50%~400% 100
Digital Vert Zoom 50%~400% 100
Digital Horz Shift 0 - 100 50
Digital Vert Shift 0 - 100 50
Off (see Note 1) Off
Horz Keystone 0 - 100 (0-20 for GEO model) 50 (10 for GEO model)
Vert Keystone 0 - 100 (0-20 for GEO model) 50 (10 for GEO model)
Horz Pincushion 0 - 100 50
Vert Pincushion 0 - 100 50
Pincushion/Barrel 0-20 10
Top Left Horz adjust. 0-160 0
Top Left Vert adjust. 0-80 0
Top Right Horz adjust. 0-160 0
Top Right Vert adjust. 0-80 0
Bottom Left Horz adjust. 0-160 0
Bottom Left Vert adjust. 0-80 0
Bottom Right Horz adjust. 0-160 0
Bottom Right Vert adjust. 0-80 0
Top Arc 0-400 200
Bottom Arc 0-400 200
Left Arc 0-400 200
Right Arc 0-400 200
Top Left Horz adjust. 0-160 0
Top Left Vert adjust. 0-80 0
Top Right Horz adjust. 0-160 0
Top Right Vert adjust. 0-80 0
Bottom Left Horz adjust. 0-160 0
Bottom Left Vert adjust. 0-80 0
Bottom Right Horz adjust. 0-160 0
Bottom Right Vert adjust. 0-80 0
Rotation 0-16 8
Top Left Horz adjust. 0-160 0
Top Left Vert adjust. 0-80 0
Top Right Horz adjust. 0-160 0
Top Right Vert adjust. 0-80 0
Bottom Left Horz adjust. 0-160 0
Bottom Left Vert adjust. 0-80 0
Bottom Right Horz adjust. 0-160 0
Bottom Right Vert adjust. 0-80 0
Auto Image command
Brightness 0 - 100 50
Contrast 0 - 100 By source set
RGB
REC709
REC601
RGB Video
Auto
Maximum
High
Normal
Low
Minimum
Color 0 - 100 50
Tint 0 - 100 50
Noise Reduction 0 - 100 0
Flesh Tone Correction 0 - 100 0
Video Black Level
Detect Film Off/On Off
Off
cc1
cc2
Red Gain 0 - 100 50
Green Gain 0 - 100 50
Blue Gain 0 - 100 50
Red Offset 0 - 100 50
Green Offset 0 - 100 50
Blue Offset 0 - 100 50
Sync Threshold 0 - 100 50
Reset RGB Gain/Offset command
Presentation
Video
Bright
Whiteboard
Blackboard
Beige Wall
User
Save to User command
DynamicBlack Off / On Off
Image settings
Size & Position
Size Presets Auto
Overscan By source set
Geometry Correction
Basic
4-Corner
Curve
Curve
4-Corner
Rotate
4-Corner
Color Space Auto
Detail By source set
Video Options
Closed captions Off
Input Levels
Picture Settings By source set
Page 82
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 6: Specications
6-9
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
Image Freeze Off / On Off
Video
Film
Bright
CRT
Normal Look
Bright Look
White Peaking 0 - 100 By source set
Warmest
Warm
Cool
Bright
Off
Normal
Maximum
2X
3X
Off
CE 1
CE 2
Language SPEC define English
Focus command
Zoom command
Lens Shift command
Allow
Locked
Lens center calibration command
Ceiling Mount Off/On/Auto Auto
Rear Projection Off/On Off
Menu Horz Offset 0 - 100 0
Menu Vert Offset 0 - 100 0
Show Messages off/on on
Menu Transparency 0 - 90 0
Factory Logo
Blue
Black
White
PIN Protect command
Change PIN command
0.5 W mode
Communication mode
AC Power On off/on off
Never
5 Mins
10 Mins
15 Mins
20 Mins
25 Mins
30 Mins
Off
2 Hrs
4 Hrs
6 Hrs
High Altitude Off/On Off
DHCP
IP Address
Subnet Mask
Default Gateway
MAC Address
Enable
Start IP
End IP
Subnet Mask
Default Gateway
MAC Address
SSID
Password
Projector Name
Show Network Messages
Restart Network…
Network Factory Reset…
2400
4800
9600
14400
19200
38400
57600
115200
1200
Serial Port Echo Off/On Off
Projector Address 0 - 9 0
Blending On/Off Off
Marker On/Off Off
Grid Off/White/Red/Green/Blue Off
Solid Color Off/White/Red/Green/Blue Off
Top 0… ½ Output Height(Pixel) 0
Bottom 0… ½ Output Height 0
Left 0… ½ Output Width 0
Right 0… ½ Output Width 0
Blending Area offset 0-2000 1000
non-Blending Area Offset 0-2000 1000
Configuration
Image Blending
Image settings
Advanced Image Settings
Gamma By source set
BrilliantColor
TM
Bright
Color Temperature By source set
Edge Enhancement Off
Color Wheel Speed 2X
Color Enhancement CE1
Lens settings
Lock all Lens Motors Allow
Menu Preferences
Splash Screen Setup Factory Logo
Power Management
Standby Mode Communication mode
Auto shutdown Never
Sleep Timer Off
Communications
LAN by set
WLAN by set
Network by set
Serial Port Baud Rate 115200
Overlap
Bright Adj.
Page 83
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
6-10
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
Drop Off Curve 70-300 100
Image Gamma 1.8/2.0/2.2/2.4/2.6 2.2
Enable On/Off Off
Auto Test Pattern On/Off On
Intensity of Red 100 - 10000 453
x of Red 0.300 - 0.700 0.633
y of Red 0.300 - 0.500 0.356
Intensity of Green 100 - 10000 2137
x of Green 0.300 - 0.400 0.352
y of Green 0.400 - 0.700 0.572
Intensity of Blue 100-10000 239
x of Blue 0.100 - 0.300 0.140
y of Blue 0.030 - 0.400 0.093
Intensity of White 100-10000 9219
x of White 0.200 - 0.400 0.331
y of White 0.200 - 0.400 0.380
Reset to Default Yes/No
Gain of Red 0.200 - 1.000 1.000
x of Red 0.300 - 0.700 0.643
y of Red 0.300 - 0.500 0.344
Gain of Green 0.200 - 1.000 1.000
x of Green 0.300 - 0.400 0.329
y of Green 0.400 - 0.700 0.544
Gain of Blue 0.200 - 1.000 1.000
x of Blue 0.100 - 0.300 0.141
y of Blue 0.030 - 0.400 0.094
Gain of White 0.200 - 1.000 1.000
x of White 0.200 - 0.400 0.334
y of White 0.200 - 0.400 0.371
Reset to Default Yes/No
Enable On/Off Off
Auto Test Pattern On/Off On
Red Part of Red 0 - 1000 1000
Green Part of Red 0 - 1000 0
Blue Part of Red 0 - 1000 0
Green Part of Green 0 - 1000 1000
Red Part of Green 0 - 1000 0
Blue Part of Green 0 - 1000 0
Blue Part of Blue 0 - 1000 1000
Red Part of Blue 0 - 1000 0
Green Part of Blue 0 - 1000 0
Red Part of White 0 - 1000 1000
Green Part of White 0 - 1000 1000
Blue Part of White 0 - 1000 1000
Reset to Default Yes/No
Blank Screen
Aspect Ratio
Freeze Screen
Projector Info
Overscan
Closed Captions
Model Name
Serial Number
Native Resolution
Firmware
Configuration
Boot Code
Standby Mode
Lens Lock Settings
Color wheel Index
FactoryReset… command
Off
Grid
White
Black
Checkerboard
Color Bars
Red
Green
Blue
Yellow
Magenta
Cyan
Color wheel Index (2x) TBD
Color wheel Index (3x) TBD
Show log
Clear log
Mode Adjustment
Lamp mode
Constant Power/Constant
Intensity
Constant Power
Constant Power
280 - 330
(280 - 350 for SONICIII)
330
(350 for SONICIII)
Constant Intensity
(see Note 5)
0 - 10 7
Lamp 1
Lamp 2
Both
Off
Lamp 1
Lamp 2
Auto
Lamp Auto Switch On Failure Only On Failure Only
Configuration
Image Blending
Lamp
Color Matching
Meter Adjustment
Measured Data
Target Data
Manual Adjustment
Hot-Key settings
Service
Projector Info
Test pattern
Error log
Current Lamp Both
Eco Mode Off
Page 84
E Series User Manual
020-000515-01 Rev. 2 (03-2013)
Section 6: Specications
6-11
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
At Power-Up
After (N) Hours
Lamp Auto Switch Time (Hours) 5 - 3000 100
Lamp 1 Hours
Lamp 2 Hours
Total Hours All Lamps
Lamp 1 Reset
Lamp 2 Reset
Lamp Life Setting xxxxx 1500 hrs
Reset Lamp Hours… command
Light Sensor Calibration command
Calibrated? (display Yes/No)
Model Name
Serial Number
Native Resolution
Firmware
˩ʿʳ˔ʿʳ˕
Main Input
Main Signal Format
Main Pixel Clock
Main Sync Type
Main Horz Refresh
Main Vert Refresh
PIP/PBP Input
PIP/PBP Signal Format
PIP/PBP Pixel Clock
PIP/PBP Sync Type
PIP/PBP Horz Refresh
PIP/PBP Vert Refresh
Lamp Power Settings
Current Lamp
Lamp 1 Hours
Lamp 2 Hours
Standby Mode
Lens Lock Settings
IP Address
DHCP
System Temperature
Main Input SPEC define
PIP/POP Input SPEC define
OFF
ON
Swap
Size (Small/Medium/Large)
Main Layout
(PBP, Main Left /PBP, Main
Top / PBP, Main Right / PBP,
Main Bottom / PIP-Bottom
Right / PIP-Bottom Left /
PIP-Top Left / PIP-Top Right)
Normal
Wide
Active Source
Signal Format
Aspect Ratio
Resolution
Vert Refresh
Horz Refresh
Pixel Clock
Sync Type
Color Space
PIP/POP (When PIP/POP active)
<PIP/POP source lines> (When PIP/POP active)
ON
OFF
VGA Key number 1
BNC Key number 2
HDMI 1 Key number 3
HDMI 2 Key number 4
Display Port Key number 5
Component Key number 6
S-Video Key number 7
Composite Key number 8
Christie Presenter Key number 9
Card Reader Key number 0
Mini USB Off
Change Sources
List all Sources
Auto Source
Language SPEC define English
Off
Grid
White
Black
Checkerboard
Color Bars
On Failure OnlyLamp Auto Switch
Lamp
Lamp Info
Light Sensor
(see Note 6).
Status
Input
Switching &
PIP
PIP/POP Enable OFF
Timing Detection Mode Wide
Test pattern
Source Info
Enable source Hot-Key ON
Source Hot-Key
Input key Auto Source
Page 85
Page 86
Japan
ph: 81-3-3599-7481
South Korea
ph: +82 2 702 1601
United Kingdom
ph: +44 118 977 8000
France
ph: +33 (0) 1 41 21 00 36
Germany
ph: +49 2161 664540
Eastern Europe
ph: +36 (0) 1 47 48 100
Middle East
ph: +971 (0) 4 299 7575
Spain
ph: + 34 91 633 9990
Singapore
ph: +65 6877-8737
Beijing
ph: +86 10 6561 0240
Shanghai
ph: +86 21 6278 7708
*36.8HP05G001-B*
P/N
36.8HP05G001-B
Loading...