Page 1
G Series
DWX600-G/DHD600-G/DWU600-G
USER MANUAL
020-000648-01
Page 2
Addendum
The CD included with this printed manual contains an electronic copy in English. Please read all instructions before
using or servicing this product.
Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les
instructions avant d'utiliser ou de réparer ce produit.
Die mit dieser gedruckten Anleitung gelieferte CD enthält eine elektronische Kopie in Deutsch. Bitte lesen Sie alle
Anweisungen, bevor Sie dieses Produkt verwenden oder warten.
Il CD fornito con il manuale stampato contiene una copia elettronica in lingua italiano. Si prega di leggere tutte le
istruzioni prima di utilizzare o riparare questo prodotto.
El DC incluido con este manual impreso contiene una copia electrónica en español. Por favor, lea todas las
instrucciones antes de usar o dar servicio a este producto.
Page 3
NOTICES
COPYRIGHT AND TRADEMARKS
© 2014 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of
their respective holders.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the product is operated in a commercial environment. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of the product in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at the user’s own expense.
WARNING! Changes or modications not expressly approved by Christie could void the user’s
authority to operate the product.
FOR COMMERCIAL USE ONLY - POUR USAGE COMMERCIAL UNIQUEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING 2 CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
CET APPAREIL NUMÉRIQUE DE CLASSE A EST CONFORME AUX NORMES DÉFINIES
DANS LES RÉGLEMENTATIONS CANADIENNES SUR LES APPAREILS CAUSANT
DES INTERFÉRENCES RADIO (CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS, ICES-003, CLASS A).
, .
Page 4
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products
or availability could occur which may not be reected in this document. Christie reserves the right
to make changes to specications at any time without notice. Performance specications are
typical, but may vary depending on conditions beyond Christie's control such as maintenance of
the product in proper working conditions. Performance specications are based on information
available at the time of printing. Christie makes no warranty of any kind with regard to this material,
including, but not limited to, implied warranties of tness for a particular purpose. Christie will not
be liable for errors contained herein or for incidental or consequential damages in connection with
the performance or use of this material.
The product is designed and manufactured with high-quality materials and components that can
be recycled and reused. This symbol
means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from regular waste. Please dispose of the product
appropriately and according to local regulations. In the European Union, there are separate
collection systems for used electrical and electronic products. Please help us to conserve the
environment we live in!
Canadian manufacturing facility is ISO 9001 and 14001 certied.
GENERAL WARRANTY STATEMENTS
For complete information about Christie’s limited warranty, please contact your Christie dealer. In
addition to the other limitations that may be specied in Christie’s limited warranty, the warranty
does not cover:
a. Damage occurring during shipment, in either direction.
b. Projector lamps (See Christie’s separate lamp program policy).
c. Damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp
supplied by a supplier other than Christie.
d. Problems caused by combination of the product with non-Christie equipment, such as distribution
systems, cameras, video tape recorders, etc., or use of the product with any non-Christie interface
device.
e. Damage caused by misuse, improper power source, accident, re, ood, lightening, earthquake or
other natural disaster.
f. Damage caused by improper installation/alignment, or by product modication, if by other than a
Christie authorized repair service provider.
g. For LCD projectors, the warranty period specied applies only where the LCD projector is in “normal
use.” “Normal use” means the LCD projector is not used more than 8 hours a day, 5 days a week.
For any LCD projector where “normal use” is exceeded, warranty coverage under this warranty
terminates after 6000 hours of operation.
h. Failure due to normal wear and tear.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your
product. Please see the Maintenance section for specic maintenance items as they relate to your
product. Failure to perform maintenance as required, and in accordance with the maintenance
schedule specied by Christie, will void the warranty.
Page 5
Table of Contents
1. SAFETY
2. INTRODUCTION
2.1 Projector Components ..................................................................................................2-1
2.2 Built-in Keypad .............................................................................................................2-4
2.3 Input/Output (I/O) Panel ...............................................................................................2-5
2.4 Remote Control ............................................................................................................2-6
2.5 LED Status Indicators ...................................................................................................2-8
3. INSTALLATION
3.1 Connect to Computer ...................................................................................................3-1
3.2 Connect to Video Equipment ........................................................................................3-2
3.3 Turn the Projector On ...................................................................................................3-3
3.4 Turn the Projector Off ...................................................................................................3-3
3.5 Adjust the Projector Position ........................................................................................3-4
3.6 Calculate Lens Offset ...................................................................................................3-5
3.7 Removing and Installing the Lens ................................................................................3-11
3.8 Cable Cover Installation ...............................................................................................3-12
4. OPERATION
4.1 Size and Position Menu ................................................................................................4-2
4.2 Image Settings Menu ....................................................................................................4-7
4.3 Conguration Menu ......................................................................................................4-10
4.4 Lamp Menu ...................................................................................................................4-15
4.5 Status Menu .................................................................................................................4-16
4.6 Input Switching & PIP Menu .........................................................................................4-19
4.7 Language Menu ............................................................................................................4-21
4.8 Test Pattern Menu ........................................................................................................4-21
4.9 Web User Interface .......................................................................................................4-22
4.9.1 Logging On ..........................................................................................................4-22
4.9.2 Main Tabbed Page – General .............................................................................4-22
4.9.3 Main Tabbed Page – Status ................................................................................4-23
4.9.4 Main Tabbed Page – Lens ..................................................................................4-24
4.9.5 Network ...............................................................................................................4-24
4.9.6 Tools ....................................................................................................................4-27
4.9.8 About Page ..........................................................................................................4-28
4.10 Christie Presenter .........................................................................................................4-29
4.10.1 Connect to the Projector ....................................................................................4-29
4.10.2 Install Christie Presenter software .....................................................................4-30
4.10.3 Use Christie Presenter ......................................................................................4-31
4.11 Card Reader Operation ................................................................................................4-37
4.12 Install the Lamp ............................................................................................................4-41
5. TROUBLESHOOTING
6. SPECIFICATIONS
6.1 Inputs ............................................................................................................................6-1
6.2 PIP/PBP Compatibility ..................................................................................................6-6
6.3 Key Features ................................................................................................................6-7
6.4 List of Components .......................................................................................................6-8
6.5 Optional Accessories ....................................................................................................6-8
6.6 REGULATORY .............................................................................................................6-9
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
i
Page 6
Table of Contents
6.7 Federal Communications Commission (FCC) Warning ................................................6-10
6.8 OSD Tree .....................................................................................................................6-11
6.9 Preset Mode tables .......................................................................................................6-19
ii
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 7
1. SAFETY
Read through this document in its entirety and understand all warnings and
precautions before attempting to operate the projector.
WARNING
yDo not look into the projector lens when the lamp is on. The bright light
may result in permanent eye damage.
To reduce the risk of re or electric shock, do not expose this projector to
y
rain or moisture.
yDo not open or disassemble the projector as this may cause electric shock.
yWhen replacing the lamp, allow the projector to cool, and follow all
replacement instructions.
When you turn the projector off, wait 180 seconds for the projector to cool
y
down before you disconnect the projector from power.
yCooling the lamp during the ignition phase may lead to ignition failures.
After a successful lamp ignition, keep the lamp burning for at least 5
minutes to maintain lamp life.
When the lamp is approaching the end of its life, the message “Lamp is
y
approaching the end of its useful life in full power operation” appears on
the screen. Change the lamp when the warning message appears.
yAll installation and maintenance procedures must be performed by a
Christie accredited service technician.
yKeep all combustible material away from the concentrated light beam of
the projector.
yPosition all cables where they cannot contact hot surfaces or be pulled or
tripped over.
Section 1: Safety
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
1-1
Page 8
Section 1: Safety
yAlways power down the projector and disconnect all power sources before
servicing or cleaning.
yUse a soft cloth moistened with a mild detergent to clean the display
housing.
yDisconnect the power plug from the AC outlet if the product is not being
used for an extended period of time.
yOperate the projector under the following conditions:
-Operating temperature range: 5°C to 35°C
-Storage temperature range: -10°C to 60°C
-
Humidity range: 5% to 80 % RH (Max.), non condensing
-Operating altitude: 10,000 ft. maximum
yUse only the AC power cord supplied. Do not attempt operation if the AC
supply and cord are not within the specied voltage and power range for
your region.
yRemove the lens plug from the lens opening in the projector before
installing the lens. Retain the lens plug to protect the optical components
from dust and debris during transport.
yDo not block the ventilation slots and openings on the projector.
yDo not use abrasive cleaners, waxes or solvents to clean the projector.
yDo not allow anything to rest on the power cord.
1-2
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 9
2. INTRODUCTION
The product specied in this document is a high brightness, high-resolution
video/graphics 1-chip mercury lamp based projector. The projector is available
in WXGA, HD and WUXGA resolutions. The projector utilizes Digital Light
Processing (DLP
for xed installation markets.
2.1 Projector Components
Front View
®
) technology from Texas Instruments. It is primarily designed
Section 2: Introduction
1
2
3
4
Ind. Part Name Description
1 Front IR Sensor
2 Projection Lens
3 Lens Ring
4 Adjustable Feet Raise or lower the feet to level the projector.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Receives signals from the IR remote. Keep the signal
path to the sensor unobstructed for uninterrupted
communication with the projector.
Allows automated lens control and adjustment: vertical
and horizontal offsets, zoom and focus.
Protects the lens motors and mechanism. Remove in
order to insert or remove the lens.
2-1
Page 10
Section 2: Introduction
Rear View
Ind. Part Name Description
1 Rear IR Sensor
Input/Output (I/O)
2
Panel
Cooling Air Vents
3
(Exhaust)
4 AC Input Connect to the supplied power adapter.
Receives signals from the IR remote. Keep the signal
path unobstructed for uninterrupted communication
with the projector.
Connects the projector to external devices.
Keep these vents unobstructed to prevent the projector
from overheating.
1
2
3
4
5
6
2-2
5 Power Button Switch the power button to turn on the power source.
6 Kensington Lock Use to secure the projector to countertops, tables, etc.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 11
Left View
Section 2: Introduction
LAMP
Right View
Ind. Part Name Description
1 Lamp Door Use the lamp door to access the lamp module.
2 LED Status Indicators
Displays the status of the projector. They are (from left
to right): LAMP, STATUS, and PIC MUTE.
1
2
3
4
3 Built-in Keypad Controls the projector.
Cooling Air Vents
4
(Intake)
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Keep these vents unobstructed to prevent the projector
from overheating.
2-3
Page 12
Section 2: Introduction
2.2 Built-in Keypad
1
2
3
4
5
6 11
Ind. Key Name Description
1 Power Turn the projector on or off
2 Menu Display menus
3 Enter Conrm a selection
4 Auto Automatically optimize image
5 Lens Adjust the lens vertical or horizontal offset setting
6 Focus Adjust focus
7 Exit Return to previous level or exit menus if at top level
8 Arrow Keys
9 Input Select an input for the main or PIP/PBP image
yAdjust a setting UP or DOWN
yNavigate within a menu
7
8
9
10
2-4
10 Picture Mute Display or blank the video image.
11 Zoom Adjust zoom
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 13
2.3 Input/Output (I/O) Panel
Section 2: Introduction
1 2 3 4 5
7 8 9
Ind. Connector Name Ind. Connector Name
1 Remote IN 8 Mini USB
2 Remote OUT 9 USB Type A
3 Component IN 10 DisplayPort
4 CVBS 11 HDMI
5 S-Video 12 VGA-IN
6 RS232 13 VGA OUT
7 Ethernet 14 DVI
10 11 12 13 14
6
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
2-5
Page 14
Section 2: Introduction
2.4 Remote Control
1
2
3
4
5
6
7
8
9
10
16
17
18
19
20
21
22
23
24
2-6
11
12
13
14
15
25
26
27
28
29
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 15
Section 2: Introduction
Ind. Key Name Description
1 Picture Mute Display or blank the video image.
2 Power on Turn projector ON.
3 Gamma Adjust mid-range levels.
4 Bright Adjust amount of light in the image.
5 PIP/PBP Turn PIP/PBP ON/OFF.
6 Size Adjust the PIP/PBP size
7 Number Keys Enter a number, such as a channel, value, etc.
8 Help Display context-sensitive help.
9 Menu Display menus.
10 Arrow Keys
11 Test Display a test pattern.
12 Auto Automatically optimize image.
13 OSD Use to hide or show menus.
14 Keystone H Adjust the horizontal keystone.
15 Keystone V Adjust the vertical keystone.
16 Standby Turn projector OFF.
17 Contrast Adjust difference between dark and light.
18 Hot-key Select your preset keys quickly.
19 Swap Swap the main and PIP/PBP images.
20 Layout Adjust the PIP/PBP layout.
21 Focus Adjust focus to improve image clarity as desired.
22 Zoom Adjust zoom to achieve a desired image size.
23 Proj Key
24 Exit Return to previous level or exit menus if at top level.
25 Enter
26 Input Select an input for the main or PIP/PBP image.
27 Info Display source image information.
28 Lens H
29 Lens V
yAdjust a setting UP or DOWN.
yNavigate within a menu.
Change the remote ID. Press Proj Key then a number
between 1 and 9 to assign an ID. Press PROJ then
number 0 to return to the universal remote ID.
ySelect a highlighted menu item.
yChange or accept a value.
Horizontal Lens Shift - Adjust the position of the image
horizontally.
Vertical Lens Shift - Adjust the position of the image
vertically.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
2-7
Page 16
Section 2: Introduction
2.5 LED Status Indicators
The LED status indicators are located on the right side of the projector. Each
LED is dened below.
yLAMP LED
LED Status Projector State
Failed to strike lamp after 5 attempts (strike attempts will
Red (short blink)
stop).
Lamp has unexpectedly shut down (system goes into cool
down state).
Yellow (no blink)
Green (no blink) Lamp is ON and operating correctly
Green (short blink) Projector lamp is switching on
Off Lamp is off
Lamp time has expired and lamp should be replaced.
(projector also begins to display the replace lamp OSD
message at startup).
ySTATUS LED
LED Status Projector State
Off Projector is in OFF state (without AC plug in)
Off, but keypad LED
is on
Green (no blink) Projector is powered up and operating normally
Flashing Yellow Projector is in cool down mode or startup mode
Flashing Green/
Yellow
Red (short blink) Fan failure
Red (no blink) Over-temperature
Green (blink very
quickly)
Projector is in standby mode (AC plug in)
Projector is in ash update state
Projector communications (Read/Write EEPROM)
2-8
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 17
Section 2: Introduction
yPICTURE MUTE LED
LED Status Projector State
Green Picture mute is off – image is displayed
Yellow Picture mute is on – image is black
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
2-9
Page 18
3. INSTALLATION
3.1 Connect to Computer
Desktop Laptop
Section 3: Installation
9
51 62 3 4
7 8
Ind. Connector Name Ind. Connector Name Ind. Connector Name
USB Type B Mini
1
Cable
4 HDMI Cable 7 RS232 Cable
2 USB Type A Cable 5 VGA in Cable 8 DVI Cable
3 DisplayPort Cable 6 VGA out Cable 9 Power Cord
NOTE:
The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
3-1
Page 19
Section 3: Installation
3.2 Connect to Video Equipment
Component video output equipment DVD player Video cassette recorder
5
2 3
41
7
6
8
Ind. Connector Name Ind. Connector Name Ind. Connector Name
1 HDMI Cable 4 S-Video Cable 7
Component (YPbPr)
2
Cable
5 VGA to RBG SCART
3 CVBS Cable 6 VGA in Cable
3 RCA Component
Cable
15-pin to 3 RCA
8
Component/HDTV
Adapter
3-2
NOTE:
The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 20
3.3 Turn the Projector On
2 3 4 5 6 7 8 9
10
3 4 5 6 7 8 9
10
4 5 6 7 8 9
10
4 5 6 7 8 9
10
3 4 5 6 7 8 9
10
2 3 4 5 6 7 8 9
10
3 4 5 6 7 8 9
10
1. Ensure that the power cord and signal cable are securely connected. The
Power button on the built in keypad is illuminated.
2. Turn on the lamp by pressing
the built-in keypad. The Status LED is yellow with a long blink.
The startup screen displays in approximately 10 seconds.
3. Turn on the source. Select Input Key on the remote control to select an
input source (VGA, BNC, HDMI, Component, S-Video or Composite
Video).
4. The projector detects the source you selected and displays the image.
NOTE:
The rst time the projector is used, the preferred language may be selected from the main menu after the startup screen is
displayed.
3
1
“ ”
Status LED
Section 3: Installation
1
on the remote control or press
2
“ ”
2
Power on
on
3.4 Turn the Projector Off
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
2
Power on
1. Press
“ ”
on the built-in keypad or on the remote control to turn off the
projector. A warning message will appear on the displayed image.
“ ”
2. Press
again to conrm your selection. If you do not press
the warning message will disappear after 10 seconds.
3
Input Key
“ ”
again,
3-3
Page 21
Section 3: Installation
3.5 Adjust the Projector Position
When you select a position for the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Follow these general guidelines:
Position the projector on a at surface at a right angle to the screen. The
y
projector (with the standard lens) must be at least 3 feet (0.9m) from the
projection screen.
yPosition the projector to the desired distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting, and
the video format determine the size of the projected image.
For the xed short lens, the image exits at a default angle. However, the
y
lens shift feature makes the image offset variable.
yLens throw ratio:
-Lens 1.22~1.53 (WU/HD)
-Lens 0.95~1.22 (WU/HD)
-Lens 1.52~2.92 (WU/HD)
-
Lens 1.28-1.61 (WX)
-
Lens 1.0-1.28 (WX)
-Lens 1.6-3.07 (WX)
yDo not roll the projector more than 20 degrees from side to side.
yDo not put the projector on either side to project an image.
3-4
20°
20°
y360 degree operation (alone the widest axis)
360°
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 22
3.6 Calculate Lens Offset
yThe vertical image offset (shift) ranges for the projector are +/-100%
(WXGA/WUXGA) and +/-120% (HD). The horizontal image offset (shift)
range for the projector are +/-20% (WXGA/HD/WUXGA).
yThe method for calculating lens offset complies with Industry standards.
Example for Vertical lens offset:
-At 0% offset (or on axis), the center of the image is on the lens center,
so that half of the image appears above and half appears below the
lens center.
-At +100% offset, all (or 100%) of the image will appear above the lens
center.
-The % offset is calculated as the ratio of the number of pixels shifted
up/down to half the image size. Examples for WUXGA:
Shifting up 600 pixels gives offset of 600/600 * 100% = 100%
`
Shifting down 600 pixels gives offset of -600/600 * 100% = -100%
`
Shifting up 720 pixels gives offset of 720/600 * 100% = 120%
`
Shifting up 240 pixels gives offset of 240/600 * 100% = 40%
`
WUXGA Projectors:
Section 3: Installation
Vertical Image Offset: 0% Offset (WUXGA)
600 pixels
above lens
center.
600 pixels
below lens
center.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
Lens center
LAMP
3-5
Page 23
Section 3: Installation
Vertical Image Offset: 100% Offset (WUXGA)
600 pixels
of shift
above lens
center.
Vertical Image Offset: -100% Offset (WUXGA)
Image has been offset 600 pixels above lens
center, so the center of the image is now 600
pixels above where the center of the image
was at 0% offset (or lens center).
The offset is
+600/600 * 100% = +100%.
Lens center
Image has been offset 600 pixels below lens
center, so the image has an offset of
-600/600 * 100% = -100%
LAMP
3-6
600 pixels
of shift
below lens
center.
Total of
1200 pixels
(600+600)
of display
are below
lens center.
Lens center
LAM
P
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 24
HD Projectors:
Vertical Image Offset: 0% Offset (HD)
540 pixels
above lens
center.
540 pixels
below lens
center.
Lens center
Vertical Image Offset: 120% Offset (HD)
Section 3: Installation
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
LAMP
648 pixels
of shift
above lens
center.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Lens center
Image has been offset 648 pixels above lens
center, so the center of the image is now 648
pixels above where the center of the image
was at 0% offset (or lens center).
The offset is
+648/540 * 100% = +120%.
LAMP
3-7
Page 25
Section 3: Installation
Vertical Image Offset: -120% Offset (HD)
648 pixels
of shift
below lens
center.
Total of
1296 pixels
(648+648)
of display
are below
lens center.
Horizontal Image Offset: +/-20% Offset
Image has been offset 648 pixels below lens
center, so the image has an offset of
-648/540 * 100% = -120%
Lens center
-192 pixels +192 pixels1920 pixels
LAM
P
3-8
Image has been offset 192 pixels
left or right of lens center.
The image has an offset of
+192/960 * 100% = +20%, or
-192/960 * 100% = -20%
Lens center
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 26
WXGA Projectors:
Vertical Image Offset: 0% Offset (WXGA)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
400 pixels
above lens
center.
400 pixels
below lens
center.
Lens center
Vertical Image Offset: 100% Offset (WXGA)
Section 3: Installation
LAMP
400 pixels of shift
above lens center.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Image has been offset 400 pixels above lens
center, so the center of the image is now 400
pixels above where the center of the image
was at 0% offset (or lens center).
The offset is
+400/400 * 100% = +100%.
Lens center
LAMP
3-9
Page 27
Section 3: Installation
Vertical Image Offset: -100% Offset (WXGA)
400 pixels of shift
below lens center.
Total of 800 pixels
(400+400) of
display are below
lens center.
Horizontal Image Offset: +/-20% Offset
Image has been offset 400 pixels below lens
center, so the image has an offset of
-400/400 * 100% = -100%
Lens center
-128 pixels +128 pixels1280 pixels
LAM
P
3-10
Image has been offset 128 pixels
left or right of lens center.
The image has an offset of
+128/640 * 100% = +20%, or
+128/640 * 100% = -20%
Lens center
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 28
3.7 Removing and Installing the Lens
When handling the projector after lens installation, make sure the front lens cap is
placed on the lens to protect the lens surface from potential damage. When carrying
or moving the projector, do not handle by the lens. This may damage the lens, the
chassis or other mechanical parts within the projector.
Installation Steps:
1. Center the lens: Ensure that the lens is at or near its center position. Attempting to
remove the lens when at a large offset may cause damage to the lens assembly. Center
the lens while the projector is switched on by pressing the lens horizontal or vertical
button and then pressing Enter.
2. Turn Off the projector: Turn the projector OFF.
3. Wait for projector to cool down: Allow the projector to cool down into standby mode
before replacing the lens. Remove power cord after the projector has cooled down and
prior to replacing the lens.
4. Remove the lens: Remove the lens ring cover.
Rotate the lens counter-clockwise by a quarter to release the lock. Remove the lens
through the front of the projector.
Section 3: Installation
5. Install the new lens: Fully insert the lens assembly straight into the lens mount without
turning. Rotate the lens cap clockwise to lock the lens in place.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
3-11
Page 29
Section 3: Installation
3.8 Cable Cover Installation
1. Rotate the cable cover and insert the two guide pins into the guide holes.
2. Press and hold both lower corners of the cable cover while inserting the sheet clips into
the projector casing.
Guide Pin
Guide Hole
Hold and Press Here
3-12
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 30
4. OPERATION
The projector has multilingual On-Screen Display (OSD) menus that allow you
to make image adjustments and change a variety of settings.
• Most of the projector controls are accessed from within the projector menu
system. There are several groups of related functions, with each group
selectable from the Main menu as shown below. Press the MENU button on
the remote control or on the built-in keypad on the rear of the projector to
display the main menu.
• Use the arrow keys to navigate within the menu and adjust a setting up or
down.
• Press ENTER to select a highlighted menu item or use it to change or
accept a value.
• Select the next item that you want to adjust in the menu and adjust it as
described above.
• Press EXIT to return to the previous menu or exit menus if at top level.
Section 4: Operation
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-1
Page 31
Section 4: Operation
4.1 Size and Position Menu
Size Presets
Display an image with the detected size, or resize the image by maximizing
either the height, width or both, or resize to the maximum size possible while
keeping the original aspect ratio.
yAuto: Display with the detected size.
yNative: Display in its native resolution.
y4:3: Retain 4:3 aspect ratio.
yLetterbox: Display with the black borders on the top and bottom.
yFull Size: Fill the screen (regardless of the source).
yFull Width: Fill display width and keep aspect ratio.
yFull Height: Fill display height and keep aspect ratio.
yCustom: Stretch the display horizontally or vertically without cutting the
image display
Overscan
Remove noise around the image. Overscan Zoom enlarges image 6% from
original size. Overscan Crop cuts 6% of active pixels in four edges of original
image.
Pixel Track
Analog RGB signals only. Steady ickering or several soft vertical stripes
or bands across the entire image indicates poor pixel tracking. Proper pixel
tracking ensures that the image quality is consistent across the screen, the
aspect ratio is maintained, and that the pixel phase can be optimized.
4-2
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 32
Section 4: Operation
Pixel Phase
Analog RGB Signals only. Adjust pixel phase when the image still shows
shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the
phase of the pixel-sampling clock relative to the incoming signal.
Horz Position
Move the image right or left within the area of available pixels.
Vert Position
Move the image up or down within the area of available pixels.
Digital Horz Zoom
Change the size of projector's display area horizontally. If the display area
has been resized by this setting, it can be moved by changing the Digital Horz
Shift and Digital Vert Shift settings.
Digital Vert Zoom
Change the size of projector's display area vertically. If the display area has
been resized by this setting, it can be moved by changing the Digital Horz
Shift and Digital Vert Shift settings.
Digital Horz Shift
Move the display area horizontally if its size has been changed by the Digital
Zoom setting.
Digital Vert Shift
Move the display area vertically if its size has been changed by the Digital
Zoom setting.
Geometry Correction
The "Geometry Correction" can be controlled with the options in the dropdown list:"Off/Basic" when optional Dual Processor Warp Module is not
installed, and "Off/Basic/Curve/Rotate" when optional Dual Processor Warp
Module is installed.
Geometry Correction Feature Compatibility
Warp Function 4-Corner
4-Corner
Curved
Surface(2x2)
Keystone
Pincushion
and Barrel
Rotation
--
Curved
Surface(2x2)
Keystone
-- X X X
X -X
X X X --
Pincushion
and Barrel
-- X
Rotation
X
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-3
Page 33
Section 4: Operation
A
yOff: No Geometric correction is applied to the image.
yHorz Keystone: Adjust the keystone horizontally and make a more square
image. Horizontal keystone is used to correct a keystoned image shape
in which the left and right borders of the image are unequal in length, and
the top and bottom are slanted to one of the sides. This is intended for use
with horizontally on-axis applications. For horizontally offset applications,
you must use 4 Corner correction using the optional Dual Processor Warp
Module.
B
A
yVert Keystone: Adjust the keystone vertically and make a more square
image. Vertical keystone is used to correct a keystoned image shape in
which the left and right borders of the image are unequal in length, and the
top and bottom are slanted to one of the sides. This is intended when for
use with horizontally on-axis applications. For horizontally offset images,
you must use 4 Corner correction using the optional Dual Processor Warp
Module.
B
Ind. WXGA 1080P WUXGA
A 12.3% 10.2% 7.1%
A
B 7.7% 6.4% 5.2%
4-4
B
A
B
Ind. WXGA 1080P WUXGA
A 5.4% 4.4% 3.3%
B 10.4% 8.7% 5.4%
yHorz Pincushion: Adjust the pincushion horizontally and make a more
square image.
Ind. WXGA 1080P WUXGA
A 16.0% 13.3% 8.0%
A B
B 16.0% 13.2% 7.9%
yVert Pincushion: Adjust the pincushion vertically and make a more square
image.
A B
Ind. WXGA 1080P WUXGA
A 14.7% 12.3% 11.4%
B 14.7% 12.1% 11.4%
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 34
Section 4: Operation
A A
AA
yPincushion/Barrel: Allow for correction for slight curved distortion from the
lens or projection surface.
Ind. WXGA 1080P WUXGA
A
B
4-Corner: Allow the image to be squeezed to t an area dened by moving
y
D
each of the four corners’ x and y position.
A 8.3% 8.35% 8.37%
C
B 3.5% 3.98% 4.59%
C
6.4% 6.4% 6.5%
D
6.4% 6.4% 6.4%
B
B
yRotation: Allow an image to be rotated – most commonly to level the
image. While the image is rotated, the software can crop any content that
begins to fall off the panel. The function will not automatically scale the
image down to prevent cropping. If scaling is required, the digital zoom
function can be used, independently of the rotation function.
B
Ind. WXGA 1080P WUXGA
A 10.0% 8.4% 8.3%
B 9.5% 7.9% 7.0%
B
A
Ind. WXGA 1080P WUXGA
A ±8.0° ±8.0° ±7.9°
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-5
Page 35
Section 4: Operation
Auto Image
Force the projector to reacquire and lock to the input signal. This is useful
when signal quality is marginal. “Normal mode” can support all of the 4:3 input
sources.
“Wide mode” can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (example
1400 x 1050), perform Auto Image using “normal mode”.
4-6
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 36
4.2 Image Settings Menu
Brightness
Adjust the intensity of the image.
Contrast
Adjust the degree of difference between the lightest and darkest parts of the
picture and change the amount of black and white in the image.
Color Space
Select a color space that has been specically tuned for the input signal.
Useful only for analog signals and certain digital sources.
Detail
Select the edge clarity of the image.
Video Options
This function is used with video sources only.
yColor: Adjust a video image from black and white to fully saturated color.
The color setting applies to video sources only.
yTint: Adjust the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
yNoise Reduction: Reduce temporal or spatial noise in the image.
Flesh Tone Correction: Control the amount of esh tone correction applied
y
to the image.
Section 4: Operation
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-7
Page 37
Section 4: Operation
yVideo Black Level: Analyze the current input image and calculate an offset
value which is then added to the analog to digital converter black level
value. This ensures optimum black level for each analog source.
Detect Film: Control lm mode detection and determine whether the
y
original source of the input video was lm or video.
yClosed Captions: Control closed caption display while audio is not muted.
If this setting is not off, audio is not muted, the source is NTSC and
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
Input Levels
VGA / Component signals only.
yAdjust the gain of the red, green, or blue channel of the image. It will affect
the black and white.
yAdjust the offset of the red, green, or blue channel of the image. It will
affect the black and white.
ySync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Picture Settings
Optimize the projector for displaying images under certain conditions, such
as presentation, video, bright, whiteboard, blackboard, beige wall and user-
denable preset. It will affect Gamma, Sharpness,White Peaking, Overscan,
Brightness, Contrast, Color, Tint, Red Gain, Green Gain, Blue Gain, Red
Offset, Green Offset, Blue Offset.
Save to User
Adjust the image settings and select Save to User as a picture setting. You
can recall these settings in the future by selecting the User in the Picture
Settings menu. The setting of Brightness, Contrast, Color, Tint, Red Gain,
Green Gain, Blue Gain, Red Offset, Green Offset, Blue Offset, Color Temp,
Gamma, Detail, BrilliantColor , Whitepeaking and Overscan will be saved.
DynamicBlack™
Select the check box to constantly adjust the aperture based on the amount of
black in the current scene.
Image Freeze
Pause the screen image.
4-8
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 38
Section 4: Operation
Advanced Image Settings
yGamma: Select the appropriate gamma from Video, Film, Bright, and CRT.
yBrilliantColor™: Produce an expanded on-screen color spectrum that
delivers enhanced color saturation for bright, true-to-life images.
yWhite Peaking: (video source only) Increase the brightness of whites that
are near 100%.
yColor Temperature: Change the intensity of the colors. Select a listed
relative warmth value.
yEdge Enhancement: Apply the edge enhancement process.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-9
Page 39
Section 4: Operation
4.3 Conguration Menu
Language
Allows you to select an available language for the OSD display, from English,
French, German, Italian, Spanish, Chinese(simplied), Japanese, Korean, and
Russian.
Lens Settings
yFocus and Zoom: Adjust the focus and zoom the image in or out.
yLens Shift: Shift the lens up and down or left and right.
yLock Lens Motors: Select this function to prevent all lens motors from
moving. It will disable the Zoom, Focus, Horizontal and Vertical Position
settings, effectively locking out any changes and overriding all other lens
features. This is particularly useful to prevent accidental lens position
changes in multi-projector installations.
yLens Calibration: Calibrate the lens center
Ceiling Mount
Turn the image upside down for ceiling-mounted projection.
Rear Projection
Reverse the image so you can project from behind a translucent screen.
4-10
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 40
Section 4: Operation
Menu Preferences
yMenu Horz Position: Change the horizontal position of the OSD.
yMenu Vert Position: Change the vertical position of the OSD.
yShow Messages: Display status messages on the screen.
yMenu Transparency: Change OSD menu background to be transparent.
NOTE:
As the value increases, more of the image behind the menu is visible.
ySplash Screen: Choose which splash screen is to be used.
PIN Protect: The PIN (personal identication number) feature allows you
y
to password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image.
yChange PIN: Allows you to change the PIN.
Power Management
yStandby Mode: The projector is in standby mode when connected to AC
power. (<0.5W)
yAC Power On: The projector automatically turns on when electrical power
is connected.
yAuto Shutdown: Automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
ySleep Timer: Allows the projector to automatically power off after it has
been on for a specied amount of time.
High Altitude
Set high altitude mode ON/OFF.When ON, the fan will operate at high speed
to ensure sufcient air ow for high altitudes.
Communications
yNetwork: Allow you to setup network settings.
- DHCP: Turn the DHCP ON/OFF.
- IP Address: Assign Network IP Address.
- Subnet Mask: Assign Network Subnet Mask.
- Default Gateway: Assign Network Default Gateway.
- Host Name: Display the host name.
- MAC Address: Displays network MAC Address value.
- Show Network Messages: Turn network messages ON/OFF.
- Restart Network: Restart the network.
- Network Factory Reset: Perform factory reset on the network settings.
The Projector Name, LAN IP, WLAN IP, and SNMP settings will be
reset.
yBaud Rate: Select the serial port and baud rate.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-11
Page 41
Section 4: Operation
ySerial Port Echo: Control whether the serial port echoes characters.
yProjector Address: Set the projector address (0-9). The projector will
respond to IR remotes set either at the same address as the projector or to
IR remotes set to address 0.
Image Blending
Adjust blend widths and settings to left, right, top and/or bottom sides to create
a seamless multi-projector stitched image. (Available only when optional Dual
Processor Warp Module is installed.)
What is a Blend?
In simple terms, a blend appears as a gradient strip along an edge of a
projected image. It is darkest along the extreme edge of the image, and
lightens nearer to the rest of the image(see below).
How are Blends used?
In multiple-projector wall, complementary blends between neighboring images
can compensate for the extra “brightness” or intensity where these edges
overlap. By controlling blend width and other properties, you can achieve
uniformity across the group of images. “Visible overlaps will disappear, as
shown below”
Overlap
With edge blending:
Blend
4-12
Overlap
,1
o
j.
1
P
r
Ima
,1
o
j. 2
P
r
,
2
o
j.
1
P
r
g
e
,
o
j. 2
P
r
Proj. 1,1 Proj. 1,2
2
Proj. 2,1 Proj. 2,2
Image
Blend
Blending regions can be dened on all sides – left, right, top and bottom. The
same gamma curve is used for all blending regions.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 42
Section 4: Operation
Color Matching
You may require a unique color gamut (range) for a single projector or
application, or you may need to precisely match colors across multiple
adjacent displays. Use Color Matching by Meter Adjustment or by Manual
Adjustment to dene the precise hue of each primary color component (red,
green, blue and white).
The x/y coordinates for each color dene its location on the standard CIE
chromaticity graph. Changing either or both of these numbers will change
the hue of the color, and modify the range of possible colors. For example,
changing the x/y coordinates for red may move the color closer to orange
or closer to violet, which will in turn affect all displayed colors having a red
component. Adjust the slide bars or enter new specic coordinates as desired
to dene or change the color gamuts needed for your environment and
applications.
Enable the selected method (Meter or Manual Adjustment)– this will
automatically disable the other method. For both methods, if Auto Test Pattern
is enabled, the solid colored test pattern will be displayed according to the
menu item on which you are positioned.
yMeter Adjustment
1. Using a color meter, enter the current x and y co-ordinates of Red,
Green, Blue and White for the projector image into the Measured Data
menu. This is the reference point for the projector. The default values
in the menu are based on the average for all projectors.
2. After measuring the values for all the projectors to be matched,
calculate the target values.
3. Enter the target values for x, y and gain for each color into the Target
Data menu.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-13
Page 43
Section 4: Operation
yManual Adjustment
1. Adjust color slide bars and judge image color by eye or meter. A user-
dened color “adjustment” can be applied.
2. Use this submenu if you do not have specic color coordinates in
mind and will judge color performance by eye or meter. As for Meter
Adjustment, each color control actually denes new x/y coordinates for
that color and changes its hue. The main colors (red part of red, green
part of green and blue part of blue) adjust the intensity of that color
component, while the modifying colors (e.g. green part of red and blue
part of red) modify the x and y value and change the hue of that color.
At the same time the main colors also are used to control the color of
the white point.
Hot-Key Settings
Assign a different function to the hot-key on the remote control by highlighting
the function in the list and pressing ENTER. Choose a function that does
not already have a dedicated button, and assign the hot-key to that function,
allowing you to quickly and easily use the chosen function.
Service
yProjector Info: Display current projector settings (read-only).
yFactory Reset: Restore all settings to their default value. It will not reset
network but it will reset RS232.
yTest Pattern: Choose the desired internal test pattern to display, or select
OFF to turn off a test pattern.
yColor wheel Index (2x): Set Color wheel index to Speed 2X. This setting
only needs to be used when the Main Board is changed, and should be
adjusted to optimize picture quality.
yColor wheel Index (3x): Set Color wheel index to Speed 3X. This setting
only needs to be used when the Main Board is changed, and should be
adjusted to optimize picture quality.
yError log: Show the projector error log for debug.
yMode Adjustment: Fine tune the H and V start position for a signal in the
EDID timing table and record the values in the system to override the
timing table. The settings must be “Saved to Record” before exiting the
menu, or they will be lost. To revert to original timing table settings, each
setting must be manually cleared. Factory Defaults will not clear these
override settings.
yLight Sensor: Calibrate the Light Sensor for use with the Constant Intensity
lamp mode, which allows the projector to be set for constant brightness. If
the Light Sensor has not been calibrated, Constant Intensity mode will be
disabled. Light Sensor calibration should be repeated when new lamps are
installed.
4-14
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 44
4.4 Lamp Menu
Lamp Mode
Select Constant Power, Constant Intensity or ECO mode. When in ECO
mode, the projector will adjust to the lowest fan speed and switch the lamp
power to the minimum setting.
Constant Power
Set the value of the lamp power (in Watts).
Constant Intensity
Set the value for the Constant Intensity to maintain constant brightness.
The light sensor will monitor the light level and will apply more power as the
lamp brightness decays naturally over time. When the lamp setting reaches
maximum power of 370W, it will remain at this setting. Note that the light
sensor needs to be calibrated for Constant Intensity mode to work properly.
Calibration should be performed again after every lamp change.
Section 4: Operation
Lamp Info
Display current lamp(s) settings (read-only).
Lamp Life Setting
Set the number of hours for the lamp life warning. After the lamp hours exceed
this value, a lamp replace message will appear. Once the lamp hour exceeds
the value of " Lamp Life Settings", a warning message box will be shown on
screen and the Lamp LED will be solid yellow at the same time.
Reset Lamp Hours
Reset the lamp used hours counter to zero. Do this after changing the lamp.
Light Sensor
Calibrate light sensor.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-15
Page 45
Section 4: Operation
4.5 Status Menu
The read-only Status menu lists a variety of details about the standard and
optional components currently detected in the projector.
For DHD Models
4-16
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 46
For DWU Models
Section 4: Operation
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-17
Page 47
Section 4: Operation
For DWX Models
4-18
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 48
4.6 Input Switching & PIP Menu
Main Input
From the list of active inputs, select one to be used as the main image.
PIP/PBP Input
From the list of active inputs, select one to be used as the PIP/PBP.
PIP/PBP Enable
Toggle between displaying two sources at once (Main and PIP/PBP images)
or one source only. The check box turns the PIP/PBP source ON and OFF.
Refer to Section 6.2 for the Main and PIP/PBP compatibility table.
Swap
Change the main image to PIP/PBP, and the PIP/PBP to main image.
Swapping is available only when PIP/PBP is enabled.
Size
Select the PIP/PBP size to small, medium or large.
Layout
Set the location of the PIP/PBP image on the screen.
Section 4: Operation
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-19
Page 49
Section 4: Operation
NOTE:
PIP/PBP layout and size table as described below.
P : indicates primary source region (lighter color).
* : Both source regions are the same size.
PIP/PBP Layout
PIP/PBP Size
Small Medium Large
PBP, Bigger Left
Over-Under, Bigger Upper
PBP, Bigger Right
Over-Under, Bigger Lower
PIP-Bottom Right
PIP-Bottom Left
PIP-Top Left
PIP-Top Right
P
P
P
P
P P P
P P
P
P P P
P P
P
P P
P
P P
*
P
*
*
*
P
P
Timing Detection
Select timing detection mode to wide or normal. It is used to support additional
PC timings. When the projected picture is not completed, this function is used
to adjust the picture. “Normal mode” can support all of the 4:3 input sources.
“Wide mode” can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (example
1400 x 1050), perform Auto Image using “normal mode”.
Source Info
Display current source settings (read-only).
Enable Source Hot-Key
Toggle the check box to enable or disable the main source hot-key.
Source Hot-Key
Allows you to assign a different source to the hot-key. Highlight an input and
press ENTER to choose a different one.
4-20
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 50
Input Key
Use it to list all of the sources or change the sources.
4.7 Language Menu
Allows you to select an available language for the OSD display.
4.8 Test Pattern Menu
Choose the desired internal test pattern to display, or select OFF to turn off a
test pattern.
yOFF
yBlack
yWhite
yCheckerboard
yGrid
yColor Bars
Section 4: Operation
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-21
Page 51
Section 4: Operation
4.9 Web User Interface
4.9.1 Logging On
Open your web browser and type the IP address (in the address bar) assigned
to your projector.
1 Select the log in level from the Access type drop-down list
2 Enter the Password in the Password eld
3 Select the appropriate language from the Language drop-down list.
4 Click the Press login button. The Main window appears.
4-22
4.9.2 Main Tabbed Page – General
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 52
Section 4: Operation
yControl Panel
Select main source / PIP source, enable/disable PIP/PBP, change the
layout / PIP size, swap, and change the test pattern.
yProjector Information Panel
Check the projector information for power status, Pic mute status, OSD
status, IP address and Mac address.
ySwitch Panel
Switch the on/off status of power, Pic mute, and OSD.
4.9.3 Main Tabbed Page – Status
Display the current status of lamp info, cooling (fans), version numbers and
signal (source) information
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-23
Page 53
Section 4: Operation
4.9.4 Main Tabbed Page – Lens
Control the focus, lens shift and zoom adjustments for the lens.
4.9.5 Network
4-24
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 54
Section 4: Operation
yRestart Network
Execute a Network restart. This will not change any of the network
settings.
yNetwork Factory Reset
Execute a network factory reset. Network settings will be reset to
the following default values:
- Projector Name = Christie@ + Serial Number
- Show Network Messages = ON
- LAN Settings:
- Manual
- IP Address = 192.168.0.100
- Subnet Mask = 255.255.255.0
- Default Gateway = 192.168.0.100
- WLAN Settings:
- Enabled
- Start IP = 192.168.1.100
- End IP = 192.168.1.120
- Subnet Mask = 255.255.255.0
- Default Gateway = 192.168.1.100
- SNMP Settings:
- SNMP Read Communication = private
- Trap IP Address = 0.0.0.0
- SMTP IP Address = 0.0.0.0
- All other settings are cleared/blanked
- Trap Conguration:
- All items = SNMP Trap + Email
yLAN Setting Panel
- Select if the projector must obtain an automatically assigned IP address
through DHCP or if the user will set the address manually.
- Enter the IP address, netmask, default gateway and DNS server
address for the TCP/IP setting.
yWLAN Setting Panel
- Select if the wireless LAN of the projector is enabled or disabled.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-25
Page 55
Section 4: Operation
- Enter the IP address range, netmask and default gateway for the
wireless LAN.
ySNMP Panel
- The G Series SNMP (Simple Network Management Protocol) interface
provides network administrators with a common way to manage their
network devices from a single remote location. SNMP allows an
administrator to query a number of devices to see their current status/
conguration. It also allows operators to change conguration values
and congure trap notications to be sent when certain events occur.
(eg. Loss of signal, power state change, etc)
Emails are sent to the mail server congured in the projector
`
settings. Up to 2 user email accounts can be selected. Any
important information regarding the event will be located in the body
content of the email.
SNMP Traps are notications that are sent from the projector. They
`
are only received by a trap receiver (MIB Browser) in the computer.
- SNMP Read Community (default setting: private) – this is a plaintext password. This must also be entered in the MIB browser. This
password allows the various settings in the projector to be queried.
- SNMP Location (default setting: blank) – This eld can be used as a
description to where a projector is located in a building. SNMP emails
sent will specify this location.
- Trap IP Address (default setting: 0.0.0.0) – This eld must be lled in to
receive Traps from the projector. The Trap IP Address should be lled
in with the IP Address of the computer on which you would like to view
received traps.
- Trap Email 1/2 (default setting: Blank) – The Trap Email 1 and 2 must
be set to an email address that is congured under the mail server that
you will enter in the “SMTP Server IP Address” eld.
- Email from Address (default setting: blank) – the “Email from Address”
that will appear as the source of the SNMP emails.
- SMTP Server IP Address (default setting: 0.0.0.0) – Enter your mail
server’s IP address.
Trap Conguration Panel
y
Set the SNMP actions for the system events. The dropdown options are:
SNMP Trap + Email, Email, SNMP Trap, and Disabled.
4-26
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 56
Section 4: Operation
4.9.6 Tools
Use the Tools tabbed pages to control “Size & Position”, “Image Settings”,
“Conguration”, “Lamp”, “Input Switching & PIP” and “Test Pattern”.
4.9.7 Administrator Page
Add or delete a user or change password
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-27
Page 57
Section 4: Operation
4.9.8 About Page
yVersion Tab
View the main rmware version, network rmware version, projector model
name, and projector serial number.
yLicense Tab
The license information of the computer program is displayed.
4-28
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 58
4.10 Christie Presenter
The Christie Presenter application allows a remote desktop from a host PC
to be displayed on the network display through Ethernet, USB, or wireless
transports. It can adapt to different network settings (DHCP, xed IP, and
direct link by USB/Ethernet cable).
Christie Presenter can be downloaded from the Christie website or from the
web page of the projector.
4.10.1 Connect to the Projector
1. Connect to the projector using WiFi or Ethernet
- Ethernet connection:
Determine the projector’s IP address from the menu Main Menu >
`
Conguration > Communications > LAN
Congure your PC IP address to be on the same network as the
`
projector.
The projector and computer must be connected directly or over the
`
network via Ethernet.
- WiFi Wireless connection:
Insert the WiFi USB dongle (1DWUSB-BGN) into the USB port on
`
the projector input panel.
Section 4: Operation
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Insert the WiFi USB dongle
4-29
Page 59
Section 4: Operation
Power on the Projector.
`
Obtain the WiFi SSID from the OSD menu Main Menu >
`
Conguration > Communications > WLAN
Connect your PC device to the wireless SSID for the selected
`
projector . Example: “Christie@0111000123”.
4.10.2 Install Christie Presenter software
1. Use a web browser to connect to the projector’s network address (Default
address 192.168.1.100)
2. Download and install the Christie Presenter Software
4-30
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 60
Section 4: Operation
3. Congure the Christie Presenter Software. The name entered is used to
identify all computers connected to the projector via the Christie Presenter
software via either wired or wireless connections. The Network Display
Management -> Device Management tab will show all current connections.
4.10.3 Use Christie Presenter
1. Press the autorun icon in the system tray to pause or play the USB display.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-31
Page 61
Section 4: Operation
2. After starting the Christie Presenter application, the main window can been
seen (shown below).
Icon Description
Connect and search network display
Stop/start displaying desktop contents to
connected network display
Select display region
Congure Christie Presenter
Manage all connected network displays
4-32
Disconnect all connections
Connect and search network display
1. Click the button
to enter into the connection menu section.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 62
Section 4: Operation
2. If the IP address of the projector is known, enter the IP address and
click the "Connect" button. If the IP address is not known, click the
"Search" button to search for the projector on the network and select
the projector to which you want to connect. Select the option "Directly"
in order to proceed to the log in interface.
3. Input “User type” and “Password” in the log-in interface. Select
the display port (the default is full screen). Obtain the " Normal "
user's password from the OSD menu Main Menu > Conguration >
Communications > WLAN.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-33
Page 63
Section 4: Operation
Select display region
Once the connection is set up, click the button
to select the size
of the projection region: FullScreen, FixedSize, or Alterable.
yFullScreen: The default capture mode turns to Full screen when the
program is launched. At that time, if screen capture starts, the image of
the whole screen is transferred to a remote network display.
yFixedSize: FixedSize mode allows the users to place a frame on the
desktop. Only the image enclosed inside the frame is transferred to
remote network display.
yAlterable: In Alterable mode the only region captured is the one
enclosed by the frame. The region can be enlarged or downsized by
dragging the eight small black squares scattered on eight edges of the
frame.
4-34
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 64
Congure Christie Presenter
Section 4: Operation
Click the button
to congure Christie Presenter for Basic Setting
and Advanced Setting.
Basic Setting: Select language, change the region size of xed size
y
capture mode, and select if notication message popup is allowed.
yAdvanced Setting: Select the quality of JPEG image, YUV sample format
and network port setting. (The "Fixed" port is Port 5900)
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-35
Page 65
Section 4: Operation
Manage all connected network displays
Click the button
to control all the users and all the projectors
connector to the same projector.
Icon Description
Administrator log in.
Normal user log in.
Device is connected.
Device is not connected.
The icon shows the current status and
display position of the local screen on the
network display. Click on the icon to change
the display position. A dialog box will appear.
4-36
Click this unlock icon to change the
password. (Password change to target
network display. Only an Administrator user
can change the password.)
No response is expected when this icon is
clicked. If user log in as "Admin", the key icon
can be seen and the Presenter password
can be changed. If user log in as "Normal",
the lock icon can be seen and the Presenter
password can't be changed.
Disconnect from target network display.
Link for connecting to a target network
display via a webpage.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 66
4.11 Card Reader Operation
There are four operation modes in the Card Reader application:
- USB Flash Devices Detection Screen
- Thumbnail Display Mode
- Images Display Mode
- Images Slide Show Mode
1. USB Flash Device Detection Screen:
In this mode, the Card Reader application detects any USB ash devices
hot-plug events and displays the ash device icon. When the ash device
is removed from USB, the icon disappears. It is suggested that USB ash
devices should be removed only when the Card Reader is changed to the
USB Flash Devices Detection Screen state.
Section 4: Operation
2. Thumbnail Display Mode:
Press the Enter key to enter the Thumbnail Display Mode. Different photos
in different folders can be chosen. Press the Menu key to bring up the
Card Reader operation UI.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-37
Page 67
Section 4: Operation
The user interface is designed to operate the card reader application with
a few keys (Enter/Left/Right/Up/Down).
The following buttons are supported in the user interface:
yPrevious: Move the selected item left. (Go to previous page when this is
the leftmost item)
yNext: Move the selected item right. (Go to next page when this is the
rightmost item.)
yDisplay: Display the selected image or display the selected folder.
yThumbnail: Enter the Thumbnail Display Mode.
ySlideShow: Enter the Slide Show Mode.
NameOrder: Sort les/folders in name order.
y
ExtendOrder: Sort les/folders in extended order.
y
SizeOrder: Sort les/folders in size order.
y
TimeOrder: Sort les/folders in time order.
y
yEXIF ON/OFF: Enable/Disable auto image rotate accordingly to EXIF
information.
FileName ON/OFF: Enable/Disable lename display in Thumbnail Display
y
Mode.
3. Image Display Mode:
Press the ENTER key in the Thumbnail Display Mode to enter the Image
Display Mode; press the SlideShow key to enter the Slide Show Mode.
The Left/Right key is used to display the last/next image in the Image
Display Mode. In the Image Display Mode, press the ENTER key to quit
from the Image Display Mode and enter the Thumbnail Display Mode.
In the Slide Show Mode, press the ENTER key to enter the Image Display
Mode.
4-38
The alternative way to display image in the Image Display Mode or Slide
Show Mode is using the operation UI.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 68
Section 4: Operation
The following operations are supported in the operation UI.
yDisplay: Enter the Image Display Mode.
yThumbnail: Enter the Thumbnail Display Mode.
ySlideShow: Enter the Slide Show Mode.
yActual Size: Display in actual size of the image.
Best Fit: Display the image in best t to the screen.
y
yEXIFDisp OFF/On: Enable/Disable EXIF information display.
y+90deg: Rotate 90 degree.
y-90deg: Rotate -90 degree.
4. Image Slide Show Mode:
The following operations are supported in the Slide Show Mode operation
UI.
yStop: Stop Slide Show Mode.
yNext: Display next image.
yPrevious: Display previous image.
yDelay 3/4/5: Slide Show delay in seconds.
ySlide Effect: Following modes are supported.
- o Slide Right
- o Blocks
- o RightDown
- o XLines
- o Slide Up
- o Ylines
- o Repeat ON/OFF: Enable/Disable Slide Show Repeat Mode.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-39
Page 69
Section 4: Operation
When the image can NOT be displayed due to memory limitation or can
NOT support image format, the specic image is displayed on the center
of the screen.
4-40
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 70
4.12 Install the Lamp
The projector automatically detects the lamp life. When the lamp life is
nearing the end of use, you will receive a warning message. "When you see
this message, please change the lamp as soon as possible." Make sure the
projector has been cooled down for at least 30 minutes before changing the
lamp.
Installation Steps:
1. Turn off the lamp: Turn the projector OFF and disconnect the power cord.
2. Wait for lamp to cool down: Allow the projector to cool down for at least 30 minutes.
Section 4: Operation
3. Open the lamp door: Push the door latch to open lock.
Loosen the captive screw securing the lamp door. Open the lamp door.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
4-41
Page 71
Section 4: Operation
4. Remove the old lamp: Loosen the three captive screws securing the lamp.
Remove the lamp module slowly and carefully.
5. Install the new lamp: Replace the lamp with a new one and tighten the three screws. Make
sure the lamp is set properly and secure.
6. Close the lamp door: Secure the captive screw.
Put the lamp door back.
7. Reset the lamp hours: Turn the projector ON and use “Reset Lamp Hours” after the lamp
module is replaced.
8. Once "Reset Lamp Hours" is pressed, a pop up check box will be shown on screen to
ask user to process Auto Brightness Calibration.
It is strongly recommend to do Auto Brightness Calibration after changing lamp to achieve
best accuracy of Constant Intensity control.
4-42
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 72
5. TROUBLESHOOTING
If you are unable to resolve an issue using the information provided in this
section, contact your reseller or service center.
Problem Solution
yNo image appears
on-screen
-Make sure all the cables and power connections are
correctly and securely connected See “Installation”.
-Check if the lamp is securely installed.
-Make sure you have removed the lens cap and the
projector is switched ON.
Section 5: Troubleshooting
yPartial, scrolling
or incorrectly
displayed image
-
Press “AUTO” on control panel or on remote control.
-
If you are using a PC (for Windows 95, 98, 2000, XP,
Windows 7):
Click the “My Computer
1.
“
double - click
Select the “Settings” tab.
2.
Verify that your display resolution setting is lower
3.
than or equal to WUXGA (1920 × 1200).
Click on the “Advanced Properties” button. If the
4.
projector is still not projecting the whole image,
change the monitor display:
4.1 Verify the resolution setting is lower than or equal
to WUXGA (1920 × 1200).
4.2 Select the
tab.
4.3 Click on
monitor types” under the SP box; choose the
resolution mode you need under the “Models”
box.
4.4 Verify that the resolution setting of the monitor
display is lower than or equal to WUXGA (1920 ×
1200).
Display”.
“
Change” button under the “Monitor”
“
Show all devices”. Next, select “Standard
” >
“Control Panel” and then
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
5-1
Page 73
Section 5: Troubleshooting
Problem Solution
yPartial, scrolling
or incorrectly
displayed image
-If you are using a Notebook:
Adjust resolution of the computer.
1.
Press the keys listed below for your notebook
2.
manufacturer to send signal out from notebook to
projector. Example: [Fn]+[F4]
Notebook Brand Function Keys
Acer [Fn]+[F5]
Asus [Fn]+[F8]
Dell [Fn]+[F8]
Gateway [Fn]+[F4]
IBM/Lenovo [Fn]+[F7]
HP/Compaq [Fn]+[F4]
NEC [Fn]+[F3]
Toshiba [Fn]+[F5]
yThe screen of
the Notebook
or PowerBook
computer is not
displaying your
presentation
yImage is unstable
or ickering
yImage has vertical
ickering bar
5-2
Mac Apple
-
If you experience difculty changing resolutions or your
System Preference Display
Arrangement Mirror display
monitor freezes, restart all equipment including the
projector.
-If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens
when a second display device is in use. Each of them has
a different method of reactivation. Please refer to your
computer manual for detailed information.
-
Use “Pixel Track” and “Pixel Phase” to correct it.
-Change the monitor color setting on your computer.
-
Use “Auto Image” to make an adjustment.
-
Check and recongure the display mode of your graphic
card to make it compatible with the projector.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 74
Problem Solution
yImage is out of
focus
-Make sure both lens caps (front and back) are removed.
-
Adjust lens focus to t.
-Make sure the projection screen is between the required
distance.
Section 5: Troubleshooting
yThe image is
stretched when
displaying 16:9
DVD title
yImage is too small
or too large
yLamp burns out or
makes a popping
sound
-When you play anamorphic DVD or 16:9 DVD, the
projector will show the best image when the projector
display mode is set to 16:9 in the OSD.
-If you play 4:3 format DVD titles, please change the format
to 4:3 in the projector OSD.
-If the image is still stretched, you will also need to adjust
the aspect ratio by setting the display format as 16:9 (wide)
aspect ratio type on your DVD player.
-
Adjust lens zoom to t.
-
If it does not ll the screen properly, verify that the correct
lens is in use or change the position of the projector.
-If the lamp burns out, try power cycling the projector. If
the lamp doesn't re or if you hear it make a loud pop, the
projector will not turn on until the lamp module has been
replaced.
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
5-3
Page 75
6. SPECIFICATIONS
6.1 Inputs
Signal
Type
Resolution
640x350 85 ● ●
640x400 85 ● ● ●
640x480 59 ●
640x480 60 ● ● ● ●
640x480 72 ● ● ●
640x480 75 ● ● ● ●
640x480 85 ● ● ● ●
720x400 85 ● ● ●
768x480 60 ●
768x480 75 ●
768x480 85 ●
Frame Rate
(Hz)
Section 6: Specications
HDMI VGA DisplayPort DVI Component S- video CVBS
PC
NOTE:
"RB" means "reduced blanking".
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
800x600 50 ● ●
800x600 56 ● ● ●
800x600 60 ● ● ● ●
800x600 72 ● ● ●
800x600 75 ● ● ● ●
800x600 85 ● ● ● ●
848x480 50 ●
848x480 60 ●
848x480 75 ●
848x480 85 ●
960x600 50 ●
960x600 60 ● ●
960x600 75 ●
6-1
Page 76
Signal
Type
PC
Resolution
960x600 85 ●
1024x768 60 ● ● ● ●
1024x768 75 ● ● ● ●
1024x768 85 ● ● ● ●
1064x600 50 ●
1064x600 60 ●
1064x600 75 ● ●
1064x600 85 ● ●
1152x720 50 ●
1152x720 60 ●
1152x720 75 ●
1152x720 85 ● ●
1152x864 60 ● ● ●
1152x864 70 ● ● ●
1152x864 75 ● ● ●
1152x864 85 ● ● ●
Frame Rate
(Hz)
HDMI VGA DisplayPort DVI Component S- video CVBS
6-2
1280x720 50 ● ●
1280x720 60 ● ● ● ●
1280x720 75 ● ● ● ●
1280x720 85 ● ● ● ●
1280x768 60 ● ● ●
1280x768 75 ● ● ●
1280x768 85 ● ● ●
1280x800 50 ● ● ● ●
1280x800 60 ● ● ● ●
1280x800 75 ● ● ●
1280x800 85 ● ● ●
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 77
Section 6: Specications
Signal
Type
PC
Resolution
1280x960 60 ● ● ●
1280x960 75 ● ● ●
1280x960 85 ● ● ●
1280x1024 50 ● ●
1280x1024 60 ● ● ● ●
1280x1024 75 ● ● ● ●
1280x1024 85 ● ● ● ●
1360x768 50 ●
1360x768 60 ●
1360x768 75 ●
1360x768 85 ●
1366x768 60 ● ● ● ●
1400x900 60 ● ● ● ●
1400x1050 50 ● ●
1400x1050 60 ● ● ● ●
1400x1050 75 ● ● ●
Frame Rate
(Hz)
HDMI VGA DisplayPort DVI Component S- video CVBS
1600x1200 50 ●
1600x1200 60 ● ● ● ●
1680x1050 50 ● ●
1680x1050 60 ● ● ● ●
1680x1050 75 ●
1728x1080 50 ●
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
1440x900 60 ● ● ●
1440x900 75 ●
1600x900 60 ●
1704x960 50 ●
1704x960 60 ●
6-3
Page 78
Signal
Type
Resolution
1728x1080 60 ●
1864x1050 50 ●
1864x1050 60 ●
Frame Rate
(Hz)
HDMI VGA DisplayPort DVI Component S- video CVBS
PC
NTSC NTSC (M, 4.43) 60 ● ●
PAL
SECAM SECAM (M) 50 ● ●
EDTV
1920X1080 50 ● ●
1920X1080 60 ● ● ●
1920X1200RB 60 ● ● ● ●
1920X1200RB 50 ● ● ● ●
PAL (B,G,H,I) 50 ● ●
PAL (N) 50 ● ●
PAL (M) 60 ● ●
480i 60 ● ● ● ●
576i 50 ● ● ● ●
480p 60 ● ● ● ●
576p 50 ● ● ● ●
6-4
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 79
Section 6: Specications
Signal
Type
HDTV
Resolution
1080i 25 ● ● ● ●
1080i 29 ● ● ● ●
1080i 30 ● ● ● ●
720p 50 ● ● ● ●
720p 59 ● ● ● ●
720p 60 ● ● ● ●
1080s 23 ● ●
1080s 24 ● ●
1080p 23 ● ● ● ●
1080p 24 ● ● ● ●
1080p 25 ● ● ● ●
1080p 29 ● ● ● ●
1080p 30 ● ● ● ●
1080p 50 ● ● ● ●
1080p 59 ● ● ● ●
Frame Rate
(Hz)
HDMI VGA DisplayPort DVI Component S- video CVBS
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
1080p 60 ● ● ● ●
6-5
Page 80
6.2 PIP/PBP Compatibility
Main
PIP/PBP
HDMI - ● - - - ● ● ● ● ●
DVI-D ● - ● ● ● ● - - - -
VGA - ● - - - - ● ● ● ●
Component - ● - - - - ● ● ● ●
S-Video - ● - - - - ● ● ● ●
CVBS - ● - - - - ● ● ● ●
RJ45 ● - ● ● ● ● - - - -
USB Type B
(mini)
USB Type A ● - ● ● ● ● - - - -
DisplayPort ● - ● ● ● ● - - - -
● : PIP/PBP combinations are enabled
- : PIP/PBP combinations are disabled
HDMI DVI-D VGA Component S-Video CVBS RJ45
● - ● ● ● ● - - - -
USB
Type B
(mini)
USB
Type A
DisplayPort
6-6
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 81
6.3 Key Features
WXGA 0.65" 1280 x 800 or HD 0.65" 1920 × 1080 resolution or WUXGA
y
0.67" 1920 × 1200 resolution
yProjection lens compatibility:
-Horizontal offset ranges: +/-20%
-Vertical offset ranges: +/-100% (WUXGA/WXGA) and +/-120% (HD)
NOTE:
Measurements are based on industry standards where offset is calculated as a ratio of the number of pixels shifted up/
down to half the image size.
yDynamic aperture enabled (full white to full dark contrast ratio): 5000:1
(Nominal)
yDual Processing Warp Module for edge blending and geometric correction.
(Optional)
yWireless desktop display using wireless dongle (optional)
SNMP traps and e-mail notications
y
ySingle mercury lamp illumination with 465W (DWH600-G/DHD600-G/
DWU600-G)
y10-bit image processor electronics with modular design
yAll video formats can be resized to full screen either horizontally or
vertically while maintaining aspect ratio
yThe projector can be operated using any of the following:
-The built-in keypad, an infrared (IR) remote control, a wired remote
control, a PC/device using serial communications (Ethernet or RS232)
-A Web page via Ethernet or from a PC/device via a wireless USB
dongle. (Optional)
yWeight:
-Maximum product weight (with lens removed): 15kg (33lb.)
yBuilt-In keypad
Section 6: Specications
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
6-7
Page 82
6.4 List of Components
This projector comes with all the items shown below. Check to make sure your
package is complete. Contact your dealer if anything is missing.
IR remote control 003-004468-01
y
yPower cord x 4
-UK/Korea/Russia
-North America
-Europe
-Japan
yDVI to HDMI dongle
yUser manual (CD)
NOTE:
Due to the difference in applications for each country, some regions may have different accessories.
6.5 Optional Accessories
yCable cover (140-103105-01)
yStandard Lens (A05) (140-100102-01)
yOptional Lens (A01) (140-101103-01)
yOptional Lens (A03) (140-102104-01)
y1DWUSB-BGN / Wireless dongle (optional accessory) (133-113106-01)
yDual Processor Warp Module (optional accessory) (133-111104-01)
6-8
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 83
6.6 REGULATORY
ySafety
-CSA C22.2 No. 60950-1
-UL 60950-1
-IEC 60950-1
-EN 60950-1
yElectro-Magnetic Compatibility
Emissions
-FCC CFR47, Part 15, Subpart B/ANSI C63.4, Class A – Unintentional
Radiators
-CISPR 22/EN55022 Class A - Information Technology Equipment
-ICES/NMB003 (A) - Information Technology Equipment
Immunity
-CISPR 24/EN55024 EMC Requirements - Information Technology
Equipment
yEnvironmental
yThe product conforms to:
-EU Directive (2011/65/EU) on the restriction of the use of certain
hazardous substances (RoHS) in electrical and electronic equipment
and the applicable ofcial amendment(s).
-EU Regulation (EC) No. 1907/2006 on the registration, evaluation,
authorization and restriction of chemicals (REACH) and the applicable
ofcial amendment(s).
-EU Directive (2012/19/EU) on waste and electrical and electronic
equipment (WEEE) and the applicable ofcial amendment(s).
-China Ministry of Information Industry Order No.39 (02/2006) on the
control of pollution caused by electronic information products, the
hazardous substances concentration limits (SJ/T11363-2006), and the
applicable product marking requirement (SJ/T11364-2006).
yMarking
-This product conforms to all relevant Canadian, US, and European
directives, standards, safety, health and environmental concerns.
International packaging recycling marks conform to:
EU Directive (2012/19/EU) on waste and electrical and electronic
`
equipment (WEEE) .
EU Directive (94/62/EC) on packaging and packaging waste
`
China packaging recycling mark standard (GB18455-2001)
`
Section 6: Specications
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
6-9
Page 84
6.7 Federal Communications Commission (FCC) Warning
WARNING
yA shielded-type power cord is required in order to meet FCC emission
limits and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used.
yUse only shielded signal cables to connect I/O devices to this equipment.
6-10
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 85
6.8 OSD Tree
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
Digital Horz Zoom 50%~400% 100
Digital Vert Zoom 50%~400% 100
Digital Horz Shift 0 - 100 50
Digital Vert Shift 0 - 100 50
Size &
Position
Section 6: Specications
Auto
Native
4:3
Size Presets
Overscan
Pixel Track 0 - 100 50
Pixel Phase 0 - 100 50
Horz Position 0 - 100 50
Vert Position 0 - 100 50
Geometry
Correction
Letterbox
Full Size
Full Width
Full Height
Custom
Off
Crop
Off Off
Horz Keystone
Vert Keystone
Horz Pincushion 0 - 100 50
Vert Pincushion 0 - 100 50
Pincushion/Barrel 0-20 10
Basic
4-Corner
Curve
Curve
4-Corner
0 - 100
(0-20 for GEO
model)
0 - 100 (0-20 for
GEO model)
Top Left
Horz adjust.
Top Left
Vert adjust.
Top Right
Horz adjust.
Top Right
Vert adjust.
Bottom Left
Horz adjust.
Bottom Left
Vert adjust.
Bottom Right
Horz adjust.
Bottom Right
Vert adjust.
Top Arc 0-400 200
Bottom Arc 0-400 200
Left Arc 0-400 200
Right Arc 0-400 200
Top Left Horz
adjust.
Top Left Vert
adjust.
Top Right Horz
adjust.
Top Right Vert
adjust.
0-140 0
0-80 0
0-140 0
0-80 0
0-140 0
0-80 0
0-140 0
0-80 0
0-160 0
0-80 0
0-160 0
0-80 0
By source setZoom
(10 for GEO
model)
(10 for GEO
model)
Auto
50
50
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
6-11
Page 86
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
Size &
Position
Image
settings
Bottom Left Horz
adjust.
Bottom Left Vert
Curve 4-Corner
Rotation 0-16 8
Geometry
Correction
Rotate
Auto Image command
Brightness 0 - 100 50
Contrast 0 - 100 By source set
Color Space
Detail
Video Options
Input Levels
Auto Auto
RGB
YUV
Maximum
High
Normal
Low
Minimum
Color 0 - 100 50
Tint 0 - 100 50
Noise Reduction 0 - 100 0
Flesh Tone
Correction
Video Black Level
Detect Film Off/On Off
Closed captions
Red Gain 0 - 100 50
Green Gain 0 - 100 50
Blue Gain 0 - 100 50
Red Offset 0 - 100 50
Green Offset 0 - 100 50
Blue Offset 0 - 100 50
Sync Threshold 0 - 100 50
Reset RGB Gain/
Offset
4-Corner
RGB
REC709
REC709
REC601
0 - 100 0
Off
cc1
cc2
command
adjust.
Bottom Right
Horz adjust.
Bottom Right
Vert adjust.
Top Left Horz
adjust.
Top Left Vert
adjust.
Top Right Horz
adjust.
Top Right Vert
adjust.
Bottom Left Horz
adjust.
Bottom Left Vert
adjust.
Bottom Right
Horz adjust.
Bottom Right
Vert adjust.
0-140 0
0-80 0
0-140 0
0-80 0
0-140 0
0-80 0
0-140 0
0-80 0
0-140 0
0-80 0
0-140 0
0-80 0
RGBRGB Video
REC709
By source set
Off
6-12
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 87
Section 6: Specications
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
Presentation
Video
Bright
Whiteboard
Blackboard
Beige Wall
Real
DICOM SIM
Video
Gamma
BrilliantColor
White Peaking 0 - 100 By source set
Color
Temperature
Edge
Enhancement
Color Wheel
Speed
Color
Enhancement
Focus command
Zoom command
Lens Shift command
Lock all Lens
Motors
Lens center
calibration
Menu Horz Offset 0 - 100 0
Menu Vert Offset 0 - 100 0
Show Messages off/on on
Menu
Transparency
Splash Screen
Setup
PIN Protect command
Change PIN command
Film
Bright
CRT
DICOM
Normal Look
TM
Bright Look
Warmest
Warm
Cool
Bright
Off
Maximum
2X
3X
Off
CE 2
Allow
Locked
command
0 - 90 0
Factory Logo
Blue
Black
White
By source set
By source set
By source set
Factory Logo
Image
settings
Conguration
Picture Settings
Save to User User
DynamicBlack command Off
Image Freeze Off / On Off
Advanced Image
Settings
Language SPEC dene English
Lens settings
Ceiling Mount Off/On/Auto Auto
Rear Projection Off/On Off
Menu Preferences
Bright
OffNormal
2X
CE1CE 1
Allow
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
6-13
Page 88
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
Conguration
Standby Mode
AC Power On off/on off
Power Management
High Altitude Off/On Off
Communications
Image Blending
Auto shutdown
Sleep Timer
LAN
WLAN
Network
Serial Port Baud
Rate
Serial Port Echo Off/On Off
Projector Address 0 - 9 0
Blending On/Off Off
Marker On/Off Off
Grid
Solid Color
0.5 W Mode
Communication
Mode
Never
5 Mins
10 Mins
15 Mins
20 Mins
25 Mins
30 Mins
Off
2 Hrs
4 Hrs
6 Hrs
DHCP
IP Address
Subnet Mask
Default Gateway
MAC Address
Enable
Start IP
End IP
Subnet Mask
Default Gateway
MAC Address
SSID
Password
Projector Name
Show Network
Messages
Restart Network…
Network Factory
Reset…
2400
4800
9600
14400
19200
38400
57600
115200
1200
Off/White/Red/
Green/Blue
Off/White/Red/
Green/Blue
Communication
mode
Never
Off
by set
by set
by set
115200
Off
Off
6-14
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 89
Section 6: Specications
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
0… ½ Output
Height(Pixel)
0… ½ Output
Height
0… ½ Output
Width
0… ½ Output
Width
0-2000 1000
0-2000 1000
Intensity of Red 100 - 10000 453
x of Red 0.300 - 0.700 0.633
y of Red 0.300 - 0.500 0.356
Intensity of Green 100 - 10000 2137
x of Green 0.300 - 0.400 0.352
y of Green 0.400 - 0.700 0.572
Intensity of Blue 100-10000 239
x of Blue 0.100 - 0.300 0.140
y of Blue 0.030 - 0.400 0.093
Intensity of White 100-10000 9219
x of White 0.200 - 0.400 0.331
y of White 0.200 - 0.400 0.380
Reset to Default Yes/No
Gain of Red 0.200 - 1.000 1.000
x of Red 0.300 - 0.700 0.643
y of Red 0.300 - 0.500 0.344
Gain of Green 0.200 - 1.000 1.000
x of Green 0.300 - 0.400 0.329
y of Green 0.400 - 0.700 0.544
Gain of Blue 0.200 - 1.000 1.000
x of Blue 0.100 - 0.300 0.141
y of Blue 0.030 - 0.400 0.094
Gain of White 0.200 - 1.000 1.000
x of White 0.200 - 0.400 0.334
y of White 0.200 - 0.400 0.371
Reset to Default Yes/No
0 - 1000 1000
0 - 1000 0
0 - 1000 0
0 - 1000 0
Conguration
Image Blending
Color Matching
TOP
Overlap
Bright Adj.
Drop Off Curve 70-300 100
Image Gamma 1.8/2.0/2.2/2.4/2.6 2.2
Meter Adjustment
Manual
Adjustment
Bottom
Left
Right
Blending Area
offset
non-Blending
Area Offset
Enable On/Off Off
Auto Test Pattern On/Off On
Measured Data
Target Data
Enable On/Off Off
Auto Test Pattern On/Off On
Red Part of Red 0 - 1000 1000
Green Part of Red 0 - 1000 0
Blue Part of Red 0 - 1000 0
Green Part of
Green
Red Part of
Green
Blue Part of
Green
Blue Part of Blue 0 - 1000 1000
Red Part of Blue 0 - 1000 0
Green Part of
Blue
0
0
0
0
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
6-15
Page 90
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
Red Part of White 0 - 1000 1000
Conguration
Color Matching
Hot-Key settings
Service
Manual
Adjustment
Blank Screen
Aspect Ratio
Freeze Screen
Projector Info
Overscan
Closed Captions
Projector Info
FactoryReset… command
Test pattern
Color wheel Index
(2x)
Color wheel Index
(3x)
Error log
Mode Adjustment
Green Part of
White
Blue Part of White 0 - 1000 1000
Reset to Default Yes/No
Model Name
Serial Number
Native Resolution
Firmware
Conguration
Boot Code
Standby Mode
Lens Lock
Settings
Color wheel Index
Off
Grid
White
Black
Checkerboard
Color Bars
Red
Green
Blue
Yellow
Magenta
Cyan
Boresight
TBD
TBD
Show log
Clear log
0 - 1000 1000
6-16
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 91
Section 6: Specications
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
Constant Power/
Lamp
Status
Lamp mode
Constant Power 360 – 465 465
Constant Intensity 0 - 10 7
Lamp Info
Lamp Life Setting xxxxx 1500 hrs
Reset Lamp
Hours…
Light Sensor
Model Name
Serial Number
Native Resolution
Firmware Vxx, Ayy, Bzz
Main Input
Main Signal Format
Main Pixel Clock
Main Sync Type
Main Horz Refresh
Main Vert Refresh
PIP/PBP Input
PIP/PBP Signal
Format
PIP/PBP Pixel Clock
PIP/PBP Sync Type
PIP/PBP Horz
Refresh
PIP/PBP Vert
Refresh
Lamp Power
Settings
Lamp Hours
Standby Mode
Lens Lock Settings
IP Address
DHCP
System
Temperature
Constant
Intensity/Eco
mode
Lamp Hours
Total Hours All
Lamps
Lamp Reset
command
Light Sensor
Calibration
Calibrated? (display Yes/No)
command
Constant
Power
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
6-17
Page 92
Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default
Main Input SPEC dene
PIP/PBP Input SPEC dene
PIP/PBP Enable
Swap
Size
Main Layout
Timing Detection
Mode
Input
Switching
& PIP
Language SPEC dene English
Test pattern
Source Info
Enable source
Hot-Key
Source Hot-Key
Input key
Blank on Signal
Switch
Off
Grid
White
Black
Checkerboard
Color Bars
OFF
ON
(Small/Medium/
Large)
(PBP, Main Left /
PBP, Main Top
/ PBP, Main
Right / PBP,
Main Bottom /
PIP-Bottom Right
/ PIP-Bottom Left
/ PIP-Top Left /
PIP-Top Right)
Normal
Wide
Active Source
Signal Format
Aspect Ratio
Resolution
Vert Refresh
Horz Refresh
Pixel Clock
Sync Type
Color Space
PIP/PBP
<PIP/PBP source
lines>
ON
OFF
VGA Key number 1
HDMI Key number 2
DVI-D Key number 3
Display Port Key number 4
Component Key number 5
S-Video Key number 6
Composite Key number 7
Christie Presenter Key number 8
Card Reader Key number 9
Mini USB Key number 0
Change Sources
Auto Source
OFF
ON
(When PIP/PBP
active)
(When PIP/PBP
active)
OFF
Wide
Auto SourceList all Sources
ON
6-18
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 93
6.9 Preset Mode tables
Descrption Bright Mode
CW 2X 3X 2X 3X 2X 3X 2X 3X 2X 3X 2X 3X 2X 3X
Syt. Mode Number 0 8 6 14 6 14 6 14 6 14 7 15 6 14
Waveform no 0 1 0 1 0 1 0 1 0 1 0 1 0 1
ColorTemp(default) BRIGHT WARM WARM WARM WARM COOL WARM
Bright 0 8 4 12 4 12 4 12 4 12 4 12 4 12
Warmes 1 9 5 13 5 13 5 13 5 13 5 13 5 13
Warm 2 10 6 14 6 14 6 14 6 14 6 14 6 14
Cool 3 11 7 15 7 15 7 15 7 15 7 15 7 15
Gamma BRIGHT FILM FILM BRIGHT CRT FILM DICOM
WhitePeaking 100 100 80 100 100 100 100
Mode NO. SQ CT mode OSD MODE CT
0 2X-Bright 2X-Native Bright Bright
1 2X-Bright 2X-D55 Bright Warmest
2 2X-Bright 2X-D65 Bright Warm
3 2X-Bright 2X-D85 Bright Cool
4 2X-Color 2X-Native
5 2X-Color 2X-D55 Warmest
6 2X-Color 2X-D65 Warm
7 2X-Color 2X-D85 Cool
8 3X-Bright 3X-Native Bright Bright
9 3X-Bright 3X-D55 Bright Warmest
10 3X-Bright 3X-D65 Bright Warm
11 3X-Bright 3X-D85 Bright Cool
12 3X-Color 3X-Native
13 3X-Color 3X-D55 Warmest
14 3X-Color 3X-D65 Warm
15 3X-Color 3X-D85 Cool
Presentation
A30H-6SW(RYGCWB) CW
Video Mode
Mode
Presenta-
tion/Video/
Whiteboard/
Blackboard/
BeingWall/
Dicom
Presenta-
tion/Video/
Whiteboard/
Blackboard/
BeingWall/
Dicom
Bright
Bright
Section 6: Specications
Whiteboard
Blackboard
Mode
Mode
Gamma
OSD
index
CRT 6 Vivid
VIDEO 5 maxbright
FILM 0 lm
Bright 4 Graphics
DICOM 13 Dicom
Beige Wall
Mode
SQ
Dicom Mode
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
6-19
Page 94
SIGNAL
Composite
S-video
VGA/PC
HDMI/DVI
Default
Mode
Video
Mode
Video
Mode
Presen-
tation
Mode
Presen-
tation
Mode
Bright-
Con-
IMAGE Mode
Presentation
Mode
Video Mode 50 50 Video Mode 34 51
Bright Mode 50 50 Bright Mode 34 51
Whiteboard
PAL
PAL
PC
Signal
PC
Signal
Mode
Blackboard
Mode
Beige Wall Mode 50 50 Beige Wall Mode 34 51
REAL Mode 50 50 REAL Mode 34 51
DICOM Mode 50 50 DICOM Mode 34 51
Presentation
Mode
Video Mode 50 50 Video Mode 34 51
Bright Mode 50 50 Bright Mode 34 51
Whiteboard
Mode
Blackboard
Mode
Beige Wall Mode 50 50 Beige Wall Mode 34 51
REAL Mode 50 50 REAL Mode 34 51
DICOM Mode 50 50 DICOM Mode 34 51
Presentation
Mode
Video Mode 49 51 Video Mode 50 51
Bright Mode 49 51 Bright Mode 50 51
Whiteboard
Mode
Blackboard
Mode
Beige Wall Mode 49 51 Beige Wall Mode 50 51
REAL Mode 49 51 REAL Mode 50 51
DICOM Mode 49 51 DICOM Mode 50 51
Presentation
Mode
Video Mode 50 50 Video Mode 36 54
Bright Mode 50 50 Bright Mode 36 54
Whiteboard
Mode
Blackboard
Mode
Beige Wall Mode 50 50 Beige Wall Mode 36 54
REAL Mode 50 50 REAL Mode 36 54
DICOM Mode 50 50 DICOM Mode 36 54
ness
50 50
50 50
50 50
50 50
50 50
50 50
49 51
49 51
49 51
50 50
50 50
50 50
trast
Default
Mode
Video
Mode
Video
Mode
Video
Mode
Video
Mode
IMAGE Mode
Presentation
NTSC
NTSC
Compo-
nent/Video
(720P,
576p/i,
1080p/i,
480p/i....)
HDMI/DVI
(SD/HD)
Whiteboard
Blackboard
Presentation
Whiteboard
Blackboard
Presentation
Whiteboard
Blackboard
Presentation
Whiteboard
Blackboard
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Bright-
ness
34 51
34 51
34 51
34 51
34 51
34 51
50 51
50 51
50 51
36 54
36 54
36 54
Contrast
6-20
G Series User Manual
020-000648-01 Rev. 3 (02-2014)
Page 95
Page 96
Corporate offi ces Worldwide offi ces
USA – Cypress
ph: 714-236-8610
Canada – Kitchener
ph: 519-744-8005
Consultant offi ces
Italy
ph: +39 (0) 2 9902 1161
Australia
ph: +61 (0) 7 3624 4888
Brazil
ph: +55 (11) 2548 4753
China (Beijing)
ph: +86 10 6561 0240
China (Shanghai)
ph: +86 21 6278 7708
Eastern Europe and
Russian Federation
ph: +36 (0) 1 47 48 100
France
ph: +33 (0) 1 41 21 44 04
Germany
ph: +49 2161 664540
For the most current technical documentation, please visit www.christiedigital.com
India
ph: +91 (080) 6708 9999
Japan (Tokyo)
ph: 81 3 3599 7481
Korea (Seoul)
ph: +82 2 702 1601
Republic of South Africa
ph: +27 (0)11 510 0094
Singapore
ph: +65 6877-8737
Spain
ph: + 34 91 633 9990
United Arab Emirates
ph: +971 4 3206688
United Kingdom
ph: +44 (0) 118 977 8000
Loading...