Christie DHD555-GS User Manual

GS Series

DWX555-GS/DHD555-GS/DWU555-GS

USER MANUAL

020-000724-01

The CD included with this printed manual contains an electronic copy in English. Please read all instructions before
using or servicing this product.

Die mit dieser gedruckten Anleitung gelieferte CD enthält eine elektronische Kopie in Deutsch. Bitte lesen Sie alle
Anweisungen, bevor Sie dieses Produkt verwenden oder warten.

Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les
instructions avant d'utiliser ou de réparer ce produit.

Il CD fornito con il manuale stampato contiene una copia elettronica in lingua italiano. Si prega di leggere tutte le
istruzioni prima di utilizzare o riparare questo prodotto.

El DC incluido con este manual impreso contiene una copia electrónica en español. Por favor, lea todas las
instrucciones antes de usar o dar servicio a este producto.

NOTICES

! ! ! ! ! ! ! ! !

! ! -! ! ! ! ! ! ! /

COPYRIGHT AND TRADEMARKS

Copyright ©2014 Christie Digital Systems USA, Inc. All rights reserved.

All brand names and product names are trademarks, registered trademarks or trade names of their
respective holders.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the product is operated in a commercial environment. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of the product in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at the user's own expense.
WARNING! Changes or modifications not expressly approved by Christie could void the user's
authority to operate the product.

FOR COMMERCIAL USE ONLY - POUR USAGE COMMERCIAL UNIQUEMENT

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING 2 CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.

CET APPAREIL NUMÉRIQUE DE CLASSE A EST CONFORME AUX NORMES DÉFINIES DANS
LES RÉGLEMENTATIONS CANADIENNES SUR LES APPAREILS CAUSANT DES
INTERFÉRENCES RADIO (CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS, ICES-003, CLASS A).

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the product s or
availability could occur which may not be reflected in this document. Christie reserves the right to
make changes to specifications at any time without notice. Performance specifications are typical,
but may vary depending on conditions beyond Christie's control such as maintenance of the
product in proper working conditions. Performance specifications are based on information
available at the time of printing. Christie makes no warranty of any kind with regard to this material,
including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be
liable for errors contained herein or for incidental or consequential damages in connection with the
performance or use of this material.

The product is designed and manufactured with high-quality materials and components that can be
recycled and reused. This symbol means that electrical and electronic equipment, at their end­of-life, should be disposed of separately from regular waste. Please dispose of the product

appropriately and according to local regulations. In the European Union, there are separate
collection systems for used electrical and electronic products. Please help us to conserve the
environment we live in!

Canadian manufacturing facility is ISO 9001 and 14001 certified.

GENERAL WARRANTY STATEMENTS

For complete information about Christie's limited warranty, please contact your Christie dealer. In
addition to the other limitations that may be specified in Christie's limited warranty, the warranty
does not cover:

a. Damage occurring during shipment, in either direction.
b. Problems caused by combination of the product with non-Christie equipment, such as distribu-

tion systems, cameras, video tape recorders, etc., or use of the product with any non-Christie
interface device.

c. Damage caused by misuse, improper power source, accident, fire, flood, lightening, earth-

quake or other natural disaster.

d. Damage caused by improper installation/alignment, or by product modification, if by other than

a Christie authorized repair service provider.

e. For LCD projectors, the warranty period specified applies only where the LCD projector is in

"normal use." "Normal use" means the LCD projector is not used more than 8 hours a day, 5
days a week. For any LCD projector where "normal use" is exceeded, warranty coverage under
this warranty terminates after 6000 hours of operation.

f. Failure due to normal wear and tear.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your
product. Please see the Maintenance section for specific maintenance items as they relate to your
product. Failure to perform maintenance as required, and in accordance with the maintenance
schedule specified by Christie, will void the warranty.

Table of Contents

1. SAFETY

2. INTRODUCTION

2.1 Projector Components ..................................................................................................2-1

2.2 Built-in Keypad..............................................................................................................2-4

2.3 Input/Output (I/O) Panel................................................................................................2-5

2.4 Remote Control.............................................................................................................2-6

2.5 LED Status Indicators ...................................................................................................2-8

3. INSTALLATION

3.1 Connect to Computer....................................................................................................3-1

3.2 Connect to Video Equipment ........................................................................................3-2

3.3 Turn the Projector On....................................................................................................3-3

3.4 Turn the Projector Off....................................................................................................3-3

3.5 Adjust the Projector Position.........................................................................................3-4

Table Top Mode3-5
Portrait Mode3-5

3-5
Inverted Mode3-5
Non-Supported Modes3-6

3.6 Calculate Lens Offset....................................................................................................3-7

3.7 Removing and Installing the Lens...............................................................................3-13

3.8 Cable Cover Installation.......................................................................... ....................3-14

3.9 Portrait Cover Installation............................................................................................3-15

3.10 Ceiling Mount Installation............................................................................................3-16

4. OPERATION

4.1 Size and Position Menu ................................................................................................4-2

4.2 Image Settings Menu....................................................................................................4-7

4.3 Configuration Menu.....................................................................................................4-10

4.4 Light Source................................................................................................................4-15

4.5 Status Menu................................................................................................................4-16

4.6 Input Switching & PIP Menu........................................................................................4-19

4.7 Language Menu..........................................................................................................4-21

4.8 Test Pattern Menu.......................................................................................................4-21

4.9 Web User Interface.....................................................................................................4-22

4.9.1 Logging On.....................................................................................................4-22

4.9.2 Main Tabbed Page - General.........................................................................4-22

4.9.3 Main Tabbed Page - Status............................................................................4-23

4.9.4 Main Tabbed Page - Lens..............................................................................4-24

4.9.5 Network..........................................................................................................4-25

4.9.6 Tools...............................................................................................................4-28

4.9.7 Administrator Page.........................................................................................4-28

4.9.8 About Page.....................................................................................................4-29

4.10 Christie Presenter .......................................................................................................4-30

4.10.1 Connect to the Projector.................................................................................4-30

4.10.2 Install Christie Presenter software..................................................................4-31

4.10.3 Use Christie Presenter...................................................................................4-32

4.11 Card Reader Operation...............................................................................................4-38

i

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Table of Contents

5. TROUBLESHOOTING

6. SPECIFICATIONS

6.1 Inputs............................................................................................................................6-1

6.2 PIP/PBP Compatibility..................................................................................................6-6

6.3 Key Features ................................................................................................................ 6-7

6.4 List of Components....................................................................................................... 6-8

6.5 Optional Accessories.................................................................................................... 6-8

6.6 REGULATORY............................................................................................................. 6-9

6.7 Federal Communications Commission (FCC) Warning.............................................. 6-10

6.8 OSD Tree.................................................................................................................... 6-11

6.9 Preset Mode tables..................................................................................................... 6-19

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

ii

Section 1: SAFETY

WARNING

1. SAFETY

Read through this document in its entirety and understand all warnings and
precautions before attempting to operate the projector.

.

• Do not look into the projector lens when the laser is on. The bright light

may result in permanent eye damage.

• To reduce the risk of fire or electric shock, do not expose this projector to

rain or moisture.

• Do not open or disassemble the projector as this may cause electric shock.

• All installation and maintenance procedures must be performed by a

Christie accredited service technician.

• Keep all combustible material away from the concentrated light beam of

the projector.

• Position all cables where they cannot contact hot surfaces or be pulled or

tripped over.

• Always power down the projector and disconnect all power sources before

servicing or cleaning.

• Use a soft cloth moistened with a mild detergent to clean the display

housing.

• Disconnect the power plug from the AC outlet if the product is not being

used for an extended period of time.

• Operate the projector under the following conditions:

- Operating temperature range: 5°C to 35°C

- Storage temperature range: -10°C to 60°C

- Humidity ran ge: 5% to 80 % RH (Max.), non conden sing

- Operating altitude: 10,000 ft. maximum

• Use only the AC power cord supplied. Do not attempt operation if the AC

supply and cord are not within the specified voltage and power range for
your region.

• Remove the lens plug from the lens opening in the projector before

installing the lens. Retain the lens plug to protect the optical components
from dust and debris during transport.

• Do not block the ventilation slots and openings on the projector.

• Do not use abrasive cleaners, waxes or solvents to clean the projector.

• Do not allow anything to rest on the power cord.

1-1

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 1: SAFETY

WARNING

Warning

This is a class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate
measures.

Important Laser Notice

MAX OUTPUT:8.0mW
WAVE LENGTH:440~455nm

Complies with 21 CFR 1040.10 and 1040.11 except
for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.
IEC 60825-1:2007

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

.

• This projector is a Class 2 laser device that conforms with IEC 60825-

1:2007 and CFR 1040.10 and 1040.11

• Class 2 laser product, Do Not Stare Into Beam

• This projector has built-in Class 4 laser module. Disassembly or
modification is very dangerous and should never be attempted.

• Any operation or adjustment not specifically instructed by the user's guide

creates the risk of hazardous laser radiation exposure.

• Do not open or disassemble the projector as this may cause damage by the

exposure of laser radiation.

• Do not stare into beam when the projector is on. The bright light may result
in permanent eye damage.

• Without following the control, adjustment or operation procedure may
cause damage by the exposure of laser radiation.

1-2

Section 2: INTRODUCTION

1

2
3

4

2. INTRODUCTION

The product specified in this document is a high brightness, high-resolution
video/graphics 1-chip laser based projector. The projector is available in
WXGA, HD and WUXGA resolutions. The projector utilizes Digital Light
Processing (DLP
for fixed installation markets.

2.1 Projector Components

Front View

®

) technology from T exas Instruments. It is primarily designed

2-1

Ind. Part Name Description

Receives signals from the IR remote. Keep the signal

1 Front IR Sensor

2 Projection Lens

3 Lens Ring

4 Adjustable Feet Raise or lower the feet to level the projector.

path to the sensor unobstructed for uninterrupted
communication with the projector.

Allows automated lens control and adjustment:
vertical and horizontal offsets, zoom and focus.

Protects the lens motors and mechanism. Remove in
order to insert or remove the lens.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 2: INTRODUCTION

K

HDBaseT REMOTE

IN

GREEN/Y BLUE/PB RED/PR RS232 USB

MINI USB

ETHERNET CVBS S-VIDEO

REMOTE

OUT

HDMI VGA IN VGA OUT DISPLAY PORT DVI

1

2

3
4

5

Rear View

Ind. Part Name Description

Receives signals from the IR remote. Keep the signal

1 Rear IR Sensor

2 Input/Output (I/O) Panel Connects the projector to external devices.

3 AC Input Connect to the supplied power adapter.

path unobstructed for uninterrupted communication
with the projector.

4 Power Button Switch the power button to turn on the power source.

5 Kensington Lock Use to secure the projector to countertops, tables, etc.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

2-2

Section 2: INTRODUCTION

1

2

3

4

Left View

Right View

2-3

Ind. Part Name Description

Cooling Air Vents

1

(Intake)

2 LED Status Indicators

3 Built-in Keypad Controls the projector.

Cooling Air Vents

4

(Exhaust)

Keep these vents unobstructed to prevent the
projector from overheating.

Displays the status of the projector. They are (from left
to right): LIGHT, STATUS, and PIC MUTE.

Keep these vents unobstructed to prevent the
projector from overheating.

020-000724-01 Rev. 1 (05-2014)

GS Series User Manual

2.2 Built-in Keypad

7

9

8

10

11

1

2
3

5

6

4

Ind. Part Name Description

1 Power Turn the projector on or off

2 Menu Display menus

3 Enter Confirm a selection

4 Auto Automatically optimize image

Section 2: INTRODUCTION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

5 Lens Adjust the lens vertical or horizontal offset setting

6 Focus Adjust focus

7 Exit Return to previous level or exit menus if at top level

8 Arrow Keys • Adjust a setting UP or DOWN

• Navigate within a menu

9 Input Select an input for the main or PIP/PBP image

10 Picture Mute Display or blank the video image.

11 Zoom Adjust zoom

2-4

Section 2: INTRODUCTION

HDBaseT REMOTE

IN

GREEN/Y BLUE/PB RED/PR RS232 USB

MINI USB

ETHERNET CVBS S-VIDEO

REMOTE

OUT

HDMI VGA IN VGA OUT DISPLAY PORT DVI

192 3 4 5 6 7 8

10

12

13 14 1511

2.3 Input/Output (I/O) Panel

Ind. Connector Name Ind. Connector Name

1 HDBaseT 9 Component IN
2 Remote IN 10 RS232
3 Remote OUT 11 Mini USB
4 HDMI 12 USB Type A
5 VGA-IN 13 Ethernet
6 VGA OUT 14 CVBS
7 Display Port 15 S-Video
8DVI

2-5

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

2.4 Remote Control

16
17

18
19

20

21

22

24

25

26
27

28

29

1
2
3
4

5

6

7

8
9
10

11
12
13

14

15

23

Section 2: INTRODUCTION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

2-6

Section 2: INTRODUCTION

Ind. Part Name Description

1 Picture Mute Display or blank the video image.
2 Power on Turn projector ON.
3 Gamma Adjust mid-range levels.
4 Bright Adjust amount of light in the image.
5 PIP/PBP Turn PIP/PBP ON/OFF.
6 Size Adjust the PIP/PBP size
7 Number Keys Enter a number, such as a channel, value, etc.
8 Help Display context-sensitive help.

9 Menu Display menus.
10 Arrow Keys
11 Test Display a test pattern.

12 Auto Automatically optimize image.
13 OSD Use to hide or show menus.
14 Keystone H Adjust the horizontal keystone.
15 Keystone V Adjust the vertical keystone.
16 Standby Turn projector OFF.
17 Contrast Adjust difference between dark and light.
18 Hot-key Select your preset keys quickly.
19 Swap Swap the main and PIP/PBP images.
20 Layout Adjust the PIP/PBP layout.
21 Focus Adjust focus to improve image clarity as desired.
22 Zoom Adjust zoom to achieve a desired image size.

23 Proj Key

24 Exit Return to previous level or exit menus if at top level.
25 Enter
26 Input Select an input for the main or PIP/PBP image.

27 Info Display source image information.
28 Lens H

29 Lens V

• Adjust a setting UP or DOWN.

• Navigate within a menu.

Change the remote ID. Press Proj Key then a number
between 1 and 9 to assign an ID. Press PROJ then
number 0 to return to the universal remote ID.

• Select a highlighted menu item.

• Change or accept a value.

Horizontal Lens Shift - Adjust the position of the image
horizontally.

Vertical Lens Shift - Adjust the position of the image
vertically.

2-7

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

2.5 LED Status Indicators

The LED status indicators are located on the right side of the projector. Each
LED is defined below.

• LIGHT LED

LED Status Projector State

Red (flashing) When projector has lost over 60% initial luminance
Orange (solid) Laser diode time has expired
Green (solid) Laser diode is on and operating correctly
Off Laser diode is off

• STATUS LED
LED Status Projector State

Off AC power is off (without AC plug in)

Section 2: INTRODUCTION

Off, but keypad LED
is on

Green (solid) Projector is powered up and operating normally
Green (flashing) Projector communications

Orange (solid)

Orange (flashing) Projector is in cool down mode or startup mode
Green (flashing) /

Red (flashing)
Red (solid) Over-temperature
Red (flashing) Fan failure

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

AC has been applied, projector is in standby mode

Non-portrait mode used
NOTE: Please refer to section 3.5.

Projector is in flash (LAN) update state

2-8

Section 2: INTRODUCTION

• PICTURE MUTE LED

LED Status Projector State

Green (solid) Light is on - image is displayed
Orange (solid) Light is on - image is blank

2-9

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 2: INTRODUCTION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

2-10

Section 3: INSTALLATION

Desktop

Laptop

1 2 3 4 5 6 7 8

9

3. INSTALLATION

3.1 Connect to Computer

HDBaseT REMOTE

REMOTE

HDMI VGA IN VGA OUT DISPLAY PORT DVI

IN

OUT

GREEN/Y BLUE/PB RED/PR RS232 USB

MINI USB

ETHERNET CVBS S-VIDEO

Ind. Connector Name Ind. Connector Name Ind. Connector Name

1 RS232 Cable 4 USB Type B Mini 7 Cable
2 HDMI Cable 5 VGA out Cable 8 DVI Cable
3 VGA in Cable 6 USB Type A Cable 9 Power Cord

NOTE:

 The diagram shows the cables/connectors that may be used to connect to various devices.
 Due to the difference in applications for each country, the accessories required in some regions may be different from those

shown.

 This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.

3-1

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

3.2 Connect to Video Equipment

Component video output equipment DVD player

1 2

3

4

5

6

7 8

Video cassette recorder

Section 3: INSTALLATION

HDBaseT REMOTE

IN

GREEN/Y BLUE/PB RED/PR RS232 USB

Ind. Connector Name Ind. Connector Name Ind. Connector Name

Component

1

(YPbPr) Cable

2

HDMI Cable 5

3

VGA to RBG
SCART

NOTE:

 The diagram shows the cables/connectors that may be used to connect to various devices.
 Due to the difference in applications for each country, the accessories required in some regions may be different from those

shown.

 This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

REMOTE

HDMI VGA IN VGA OUT DISPLAY PORT DVI

OUT

MINI USB

ETHERNET CVBS S-VIDEO

4 VGA in Cable 7 CVBS Cable

3 RCA Component
Cable

15-pin to 3 RCA

6

Component/HDTV

8 S-Video Cable

Adapter

3-2

Section 3: INSTALLATION

3.3 Turn the Projector On

1. Ensure that the power cord and signal cable are securely connected. The
Power button on the built in keypad is illuminated.

1

2. Turn on the projector by pressing " " on the remote control or press " "

2

on the built-in keypad. The Status LED is Orange with a long blink.

1

3. Turn on the source. Select Input Key on the remote control to select an
input source (VGA, BNC, HDMI, Component, S-Video or Composite

3

Video).

1

4. The projector detects the source you selected and displays the image.

NOTE:

 The first time the projector is used, the preferred language may be selected from the main menu after the startup screen is dis-

played.

2

1

Power on

2

1

1

Status LED

2

1

Power on

3

1

Input Key

3.4 Turn the Projector Off

1. Press " " on the built-in keypad or on the remote control to turn off the
projector. A warning message will appear on the displayed image.

2. Press " " again to confirm your selection. If you do not press " " again,
the warning message will disappear after 10 seconds.

3-3

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

3.5 Adjust the Projector Position

When you select a position for the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Follow these general guidelines:

• Position the projector on a flat surface at a right angle to the screen. The

projector (with the standard lens) must be at least 3 feet (0.9m) from the
projection screen.

• Position the projector to the desired distance from the screen. The distance

from the lens of the projector to the screen, the zoom setting, and the video
format determine the size of the projected image.

• For the fixed short lens, the image exits at a default angle. However, the

lens shift feature makes the image offset variable.

• Lens throw ratio:

- Lens 1.22~1.53 (WU/HD)

- Lens 0.95~1.22 (WU/HD)

- Lens 1.52~2.92 (WU/HD)

- Lens 1.28-1.61 (WX)

- Lens 1.0-1.28 (WX)

- Lens 1.6-3.07 (WX)

• 360 degree operation (alone the widest axis)

Section 3: INSTALLATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

360°

3-4

Section 3: INSTALLATION

WARNING

0 deg

0~60 deg

300~360 deg

Portrait mode
60~120 deg

Portrait mode
60~120 deg

120~180 deg

180 deg

180~240 deg

Table Top Mode

- The projector is in table top mode when the viewing angle is from 0° to

<60° and from >300° to 360° as illustrated below.

Portrait Mode

- The projector is in portrait mode when the viewing angle is from 60° to

120° as illustrated below.

3-5

• In portrait orientation, the Portrait Side Cover must be installed on the side
of the projector which is now the lower side. Refer to section 3.9.

Inverted Mode

- The projector is in Inverted/Ceiling Mount Mode when the viewing angle

is from >120° to <240° as illustrated below.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 3: INSTALLATION

WARNING

240~270 deg

270 deg

270~300 deg

Non-Supported Modes

- The projector is in non-portrait mode when the viewing angle is 240° to
300° as illustrated below.

- The "orange" status LED on projector lights on.

• The projector should not be operated in Non-Portrait Mode .

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

3-6

Section 3: INSTALLATION

No offset is applied - 0% offset.
Half of the image appears ab ove lens cen ter
and half of the image appears below lens
center.

600 pixels
above lens
center.

600 pixels
above lens
center.

Lens center

3.6 Calculate Lens Offset

• The vertical image offset (shift) ranges for the projector are +/-100%
(WXGA/WUXGA) and +/-120% (HD). The horizontal image offset (shift)
range for the projector are +/-30% (WXGA/HD/WUXGA).

• The method for calculating lens offset complies with Industry standards.
Example for Vertical lens offset:

- At 0% offset (or on axis), the center of the image is on the lens center,

so that half of the image appears above and half appears below the
lens center.

- At +100% offset, all (or 100%) of the image will appear above the lens

center.

- The % offset is calculated as the ratio of the number of pixels shifted up/

down to half the image size. Examples for WUXGA:

 Shifting up 600 pixels gives offset of 600/600 * 100% = 100%
 Shifting down 600 pixels gives offset of -600/600 * 100% = -100%
 Shifting up 720 pixels gives offset of 720/600 * 100% = 120%
 Shifting up 240 pixels gives offset of 240/600 * 100% = 40%

WUXGA Projectors:

Vertical Image Offset: 0% Offset (WUXGA)

3-7

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 3: INSTALLATION

Image has been offset 600 pixels above
lens center, so the center of the image is
now 600 pixels above where the ce nter of
the image was at 0% offset (or lens center).
The offset is +600/600 * 100% = +100%.

600 pixels of
shift above
lens center.

Lens center

Image has been offset 600 pixels below len s
center, so the image has an offset of -600/
600 * 100% = -100%

600 pixels
of shift
below lens
center.

Lens center

Total of
1200 pixels
(600+600)
of display
are below
lens center.

Vertical Image Offset: 100% Offset (WUXGA)

Vertical Image Offset: -100% Offset (WUXGA)

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

3-8

Section 3: INSTALLATION

No offset is applied - 0% offset.
Half of the image appears ab ove lens cen ter
and half of the image appears below lens
center.

540 pixels
above lens
center.

540 pixels
above lens
center.

Lens center

Image has been offset 648 pixels above
lens center, so the center of the image is
now 648 pixels above where the center of
the image was at 0% offset (or lens center).
The offset is +648/540 * 100% = +120%.

648 pixels of
shift above
lens center.

Lens center

HD Projectors:

Vertical Image Offset: 0% Offset (HD)

Vertical Image Offset: 120% Offset (HD)

3-9

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Vertical Image Offset: -120% Offset (HD)

Image has been offset 648 pixels below len s
center, so the image has an offset of -648/
540 * 100% = -120%

648 pixels
of shift
below lens
center.

Lens center

Total of
1296 pixels
(648+648)
of display
are below
lens center.

Image has been offset 192 pixels
left or right of lens center.
The image has an offset of +192/
960 * 100% = +20%, or -192/960 *
100% = -20%

Lens center

-192 pixels

1920 pixels +192 pixels

Horizontal Image Offset: +/-30% Offset

Section 3: INSTALLATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

3-10

Section 3: INSTALLATION

No offset is applied - 0% offset.
Half of the image appears ab ove lens cen ter
and half of the image appears below lens
center.

400 pixels
above lens
center.

400 pixels
above lens
center.

Lens center

Image has been offset 400 pixels above
lens center, so the center of the image is
now 400 pixels above where the center of
the image was at 0% offset (or lens center).
The offset is +400/400 * 100% = +100%.

400 pixels of shift
above lens center.

Lens center

WXGA Projectors:

Vertical Image Offset: 0% Offset (WXGA)

Vertical Image Offset: 100% Offset (WXGA)

3-11

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Vertical Image Offset: -100% Offset (WXGA)

Image has been offset 400 pixels below len s
center, so the image has an offset of -400/
400 * 100% = -100%

400 pixels of shift
below lens center.

Total of 800 pixels
(400+400) of
display are below
lens center.

Lens center

Image has been offset 128 pixels
left or right of lens center. The
image has an offset of +128/640
* 100% = +20%, or +128/640 *
100% = -20%

Lens center

-128 pixels

1280 pixels +128 pixels

Horizontal Image Offset: +/-30% Offset

Section 3: INSTALLATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

3-12

Section 3: INSTALLATION

3.7 Removing and Installing the Lens

When handling the projector after lens installation, make sure the front lens
cap is placed on the lens to protect the lens surface from potential damage.
When carrying or moving the projector, do not handle by the lens. This may
damage the lens, the chassis or other mechanical parts within the projector.

Installation Steps:

1. Center the lens: Ensure that the lens is at or near its center position.
Attempting to remove the lens when at a large offset may cause damage to
the lens assembly. Center the lens while the projector is switched on by
pressing the lens horizontal or vertical button and then pressing Enter.

2. Turn Off the projector: Turn the projector OFF.

3. Wait for projector to cool down: Allow the projector to cool down into
standby mode before replacing the lens. Remove power cord after the
projector has cooled down and prior to replacing the lens.

4. Remove the lens: Remove the lens ring cover.
Rotate the lens counter-clockwise by a quarter to release the lock. Remove

the lens through the front of the projector.

3-13

5. Install the new lens: Fully insert the lens assembly straight into the lens
mount without turning. Rotate the lens cap clockwise to lock the lens in
place.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

3.8 Cable Cover Installation

Guide Pin
Guide Hole

Hold and Press Here

1. Rotate the cable cover and insert the two guide pins into the guide holes.

2. Press and hold both lower corners of the cable cover while inserting the

sheet clips into the projector casing.

Section 3: INSTALLATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

3-14

Section 3: INSTALLATION

WARNING

Tighten the six screws

3.9 Portrait Cover Installation

1. Attach the Portrait cover to the left side of the projector and secure with the
6 step screws.

3-15

2. Mount the projector in an appropriate mounting kit, using the 4 mounting
points on the underside of the projector.

• Mount with the portrait cover side facing downwards.

• The projector must not stand on a table top on the portrait cover

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

3.10 Ceiling Mount Installation

Mount the projector with an appropriate mounting kit, using the 4 mounting
points on the underside of the projector.

• When not mounted properly, the projector may fall, causing hazards or

injury. The warranty on this projector does not cover any damage caused
by the use of any non-recommended ceiling mount kit or installation of the
ceiling mount kit in an improper location.

• Refer to the installation instructions and safety guidelines provided in the

kit.

Section 3: INSTALLATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

3-16

Section 4: OPERATION

4. OPERATION

The projector has multilingual On-Screen Display (OSD) menus that allow you
to make image adjustments and change a variety of settings.

• Most of the projector controls are accessed from within the projector menu
system. There are several groups of related functions, with each group
selectable from the Main menu as shown below. Press the MENU button on
the remote control or on the built-in keypad on the rear of the projector to
display the main menu.

• Use the arrow keys to navigate within the menu and adjust a setting up or
down.

• Press ENTER to select a highlighted menu item or use it to change or
accept a value.

• Select the next item that you want to adjust in the menu and adjust it as
described above.

• Press EXIT to return to the previous menu or exit menus if at top level.

4-1

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4.1 Size and Position Menu

Size Presets

Display an image with the detected size, or resize the image by maximizing
either the height, width or both, or resize to the maximum size possible while
keeping the original aspect ratio.

• Auto: Display with the detected size.

• Native: Display in its native resolution.

• 4:3: Retain 4:3 aspect ratio.

• Letterbox: Display with the black borders on the top and bottom.

• Full Size: Fill the screen (regardless of the source).

• Full Width: Fill display width and keep aspect ratio.

• Full Height: Fill display height and keep aspect ratio.

• Custom: Stretch the display horizontally or vertically without cutting the

image display

Overscan

Remove noise around the image. Overscan Zoom enlarges image 6% from
original size. Overscan Crop cuts 6% of active pixels in four edges of original
image.

Pixel Track

Analog RGB signals only. Steady flickering or several soft vertical stripes or
bands across the entire image indicates poor pixel tracking. Proper pixel
tracking ensures that the image quality is consistent across the screen, the
aspect ratio is maintained, and that the pixel phase can be optimized.

Section 4: OPERATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-2

Section 4: OPERATION

Pixel Phase

Analog RGB Signals only. Adjust pixel phase when the image still shows
shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the
phase of the pixel-sampling clock relative to the incoming signal.

Horz Position

Move the image right or left within the area of available pixels.

Vert Position

Move the image up or down within the area of available pixels.

Digital Horz Zoom

Change the size of projector's display area horizontally. If the display area has
been resized by this setting, it can be moved by changing the Digital Horz Shift

and Digital Vert Shift settings.

Digital Vert Zoom

Change the size of projector's display area vertically. If the display area has
been resized by this setting, it can be moved by changing the Digital Horz Shift
and Digital Vert Shift settings.

Digital Horz Shift

Move the display area horizontally if its size has been changed by the Digital
Zoom setting.

Digital Vert Shift

Move the display area vertically if its size has been changed by the Digital
Zoom setting.

Geometry Correction

The "Geometry Correction" can be controlled with the options in the drop­down list:"Off/Basic" when optional Dual Processor Warp Module is not
installed, and "Off/Basic/Curve/Rotate" when optional Dual Processor Warp
Module is installed.

4-3

Geometry Correction Feature Compatibility

Warp Function 4-Corner

4-Corner --    

Curved

Surface(2x2)

Keystone  X --  X

Pincushion and

Barrel

Rotation  X X X --

 -- X X X

 X  -- X

Curved

Surface(2x2)

Keystone

Pincushion and

Barrel

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Rotation

Section 4: OPERATION

A

• Off: No Geometric correction is applied to the image.

• Horz Keystone: Adjust the keystone horizontally and make a more square

image. Horizontal keystone is used to correct a keystoned image shape in
which the left and right borders of the image are unequal in length, and the
top and bottom are slanted to one of the sides. This is intended for use with
horizontally on-axis applications. For horizontally offset applications, you
must use 4 Corner correction using the optional Dual Processor Warp
Module.

B

A

• Vert Keystone: Adjust the keystone vertically and make a more square

image. Vertical keystone is used to correct a keystoned image shape in
which the left and right borders of the image are unequal in length, and the
top and bottom are slanted to one of the sides. This is intended when for
use with horizontally on-axis applications. For horizontally offset images,
you must use 4 Corner correction using the optional Dual Processor Warp
Module.

B

A

Ind. WXGA 1080P WUXGA

A 12.3% 10.2% 7.1%
B 7.7% 6.4% 5.2%

A

• Horz Pincushion: Adjust the pincushion horizontally and make a more

square image.

A B

• Vert Pincushion: Adjust the pincushion vertically and make a more square

image.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

B

B

A B

Ind. WXGA 1080P WUXGA

A 5.4% 4.4% 3.3%
B 10.4% 8.7% 5.4%

Ind. WXGA 1080P WUXGA

A 16.0% 13.3% 8.0%
B 16.0% 13.2% 7.9%

Ind. WXGA 1080P WUXGA

A 14.7% 12.3% 11.4%
B 14.7% 12.1% 11.4%

4-4

Section 4: OPERATION

A A

AA

• Pincushion/Barrel: Allow for correction for slight curved distortion from the
lens or projection surface.

B

• 4-Corner: Allow the image to be squeezed to fit an area defined by moving
each of the four corners' x and y position.

A

D

Ind. WXGA 1080P WUXGA

C

A 8.38% 8.35% 8.37%

B 3.5% 3.98% 4.59%

C 6.4% 6.4% 6.5%

D 6.4% 6.4% 6.5%

B

B

B

Ind. WXGA 1080P WUXGA

A 10.0% 8.4% 8.3%

B 9.5% 7.9% 7.0%

B

• Rotation: Allow an image to be rotated - most commonly to level the image.
While the image is rotated, the software can crop any content that begins to
fall off the panel. The function will not automatically scale the image down
to prevent cropping. If scaling is required, the digital zoom function can be
used, independently of the rotation function.

A

Ind. WXGA 1080P WUXGA

A 10.0% 8.4% 8.3%

4-5

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

Auto Image

Force the projector to reacquire and lock to the input signal. This is useful
when signal quality is marginal. "Normal mode" can support all of the 4:3 input
sources.

"Wide mode" can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (example

1400 x 1050), perform Auto Image using "normal mode".

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-6

Section 4: OPERATION

4.2 Image Settings Menu

Brightness

Adjust the intensity of the image.

Contrast

Adjust the degree of difference between the lightest and darkest parts of the
picture and change the amount of black and white in the image.

Color Space

Select a color space that has been specifically tuned for the input signal.
Useful only for analog signals and certain digital sources.

Detail

Select the edge clarity of the image.

Video Options

This function is used with video sources only.

• Color: Adjust a video image from black and white to fully saturated color.
The color setting applies to video sources only.

• Tint: Adjust the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.

• Noise Reduction: Reduce temporal or spatial noise in the image.

• Flesh Tone Correction: Control the amount of flesh tone correction applied
to the image.

4-7

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

• Video Black Level: Analyze the current input image and calculate an offset

value which is then added to the analog to digital converter black level
value. This ensures optimum black level for each analog source.

• Detect Film: Control film mode detection and determine whether the

original source of the input video was film or video.

• Closed Captions: Control closed caption display while audio is not muted.

• If this setting is not off, audio is not muted, the source is NTSC and

contains captions on the selected channel, then the projector must display
caption text overlaid on the image.

Input Levels

VGA / Component signals only.

• Adjust the gain of the red, green, or blue channel of the image. It will affect

the black and white.

• Adjust the offset of the red, green, or blue channel of the image. It will

affect the black and white.

• Sync Threshold: (progressive signals only) If a hardware device, such as a

DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.

Picture Settings

Optimize the projector for displaying images under certain conditions, such as
presentation, video, bright, real, dicom sim, and user-definable preset. It will
affect Gamma, Sharpness,White Peaking, Overscan, Brightness, Contrast,
Color, Tint, Red Gain, Green Gain, Blue Gain, Red Offset, Green Offset, Blue
Offset.

Save to User

Adjust the image settings and select Save to User as a picture setting. You can
recall these settings in the future by selecting the User in the Picture Settings
menu. The setting of Brightness, Contrast, Color, Tint, Red Gain, Green Gain,
Blue Gain, Red Offset, Green Offset, Blue Offset, Color Temp, Gamma, Detail,
Whitepeaking and Overscan will be saved.

Image Freeze

Pause the screen image.

Advanced Image Settings

• Gamma: Select the appropriate gamma from Video, Film, Bright, CRT, and

DICOM.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-8

Section 4: OPERATION

• White Peaking: (video source only) Increase the brightness of whites that
are near 100%.

• Color Temperature: Change the intensity of the colors. Select a listed
relative warmth value.

• Edge Enhancement: Apply the edge enhancement process.

4-9

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4.3 Configuration Menu

Language

Allows you to select an available language for the OSD display, from English,
French, German, Italian, Spanish, Chinese(simplified), Japanese, Korean, and
Russian.

Lens Settings

• Focus and Zoom: Adjust the focus and zoom the image in or out.

• Lens Shift: Shift the lens up and down or left and right.

• Lock Lens Motors: Select this function to prevent all lens motors from

moving. It will disable the Zoom, Focus, Horizontal and Vertical Position
settings, effectively locking out any changes and overriding all other lens
features. This is particularly useful to prevent accidental lens position
changes in multi-projector installations.

• Lens Calibration: Calibrate the lens center

Ceiling Mount

Turn the image upside down for ceiling-mounted projection.

Rear Projection

Reverse the image so you can project from behind a translucent screen.

Section 4: OPERATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-10

Section 4: OPERATION

Menu Preferences

• Menu Horz Position: Change the horizontal position of the OSD.

• Menu Vert Position: Change the vertical position of the OSD.

• Show Messages: Display status messages on the screen.

• Menu Transparency: Change OSD menu background to be transparent.

NOTE:

 As the value increases, more of the image behind the menu is visible.

• Splash Screen: Choose which splash screen is to be used.

• PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you

must enter the PIN before you can project an image.

• Change PIN: Allows you to change the PIN.

Power Management

• Standby Mode: The projector is in standby mode when connected to AC

• power. (<0.5W)

• AC Power On: The projector automatically turns on when electrical power
is connected.

• Auto Shutdown: Automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received

before the projector powers down, the image will be displayed.

• Sleep Timer: Allows the projector to automatically power off after it has
been on for a specified amount of time.

High Altitude

Set high altitude mode ON/OFF.When ON, the fan will operate at high speed
to ensure sufficient air flow for high altitudes.

Communications

• Network: Allow you to setup network settings.

- DHCP: Turn the DHCP ON/OFF.

- IP Address: Assign Network IP Address.

- Subnet Mask: Assign Network Subnet Mask.

- Default Gateway: Assign Network Default Gateway.

- Host Name: Display the host name.

- MAC Address: Displays network MAC Address value.

- Show Network Messages: Turn network messages ON/OFF.

- Restart Network: Restart the network.

- Network Factory Reset: Perform factory reset on the network settings.

The Projector Name, LAN IP, WLAN IP, and SNMP settings will be
reset.

• Baud Rate: Select the serial port and baud rate.

4-11

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

Overlap

Overlap

Blend

With edge blending:

Blend

Proj. 1,1

Proj. 1,2

Proj. 2,2

Proj. 2,1

Proj. 1,2

Proj. 1,1

Proj. 2,1

Proj. 2,2

Proj. 1,2

Image

Image

• Serial Port Echo: Control whether the serial port echoes characters.

• Serial Port Path: Select the serial port path from either RS232 or HDBaseT.

• Projector Address: Set the projector address (0-9). The projector will

respond to IR remotes set either at the same address as the projector or to
IR remotes set to address 0.

Image Blending

Adjust blend widths and settings to left, right, top and/or bottom sides to create
a seamless multi-projector stitched image. (Available only when optional Dual
Processor Warp Module is installed.)

What is a Blend?

In simple terms, a blend appears as a gradient strip along an edge of a
projected image. It is darkest along the extreme edge of the image, and
lightens nearer to the rest of the image(see below).

How are Blends used?

In multiple-projector wall, complementary blends between neighboring images
can compensate for the extra "brightness" or intensity where these edges
overlap. By controlling blend width and other properties, you can achieve
uniformity across the group of images. "Visible overlaps will disappear, as
shown below"

Blending regions can be defined on all sides - left, right, top and bottom. The
same gamma curve is used for all blending regions.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-12

Section 4: OPERATION

Measured
Data

Targ et Data

Color Matching

You may require a unique color gamut (range) for a single projector or
application, or you may need to precisely match colors across multiple
adjacent displays. Use Color Matching by Meter Adjustment or by Manual
Adjustment to define the precise hue of each primary color component (red,
green, blue and white).

The x/y coordinates for each color define its location on the standard CIE
chromaticity graph. Changing either or both of these numbers will change the
hue of the color, and modify the range of possible colors. For example,
changing the x/y coordinates for red may move the color closer to orange or
closer to violet, which will in turn affect all displayed colors having a red
component. Adjust the slide bars or enter new specific coordinates as desired
to define or change the color gamuts needed for your environment and
applications.
Enable the selected method (Meter or Manual Adjustment)- this will
automatically disable the other method. For both methods, if Auto Te st Pattern
is enabled, the solid colored test pattern will be displayed according to the
menu item on which you are positioned.

• Meter Adjustment
1 Using a color meter, enter the current x and y co-ordinates of Red,

Green, Blue and White for the projector image into the Measured Data
menu. This is the reference point for the projector. The default values in
the menu are based on the average for all projectors.

2 After measuring the values for all the projectors to be matched,

calculate the target values.

3 Enter the target values for x, y and gain for each color into the Target

Data menu.

4-13

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

• Manual Adjustment

1 Adjust color slide bars and judge image color by eye or meter. A user-

defined color "adjustment" can be applied.

2 Use this submenu if you do not have specific color coordinates in mind

and will judge color performance by eye or meter. As for Meter
Adjustment, each color control actually defines new x/y coordinates for
that color and changes its hue. The main colors (red part of red, green
part of green and blue part of blue) adjust the intensity of that color
component, while the modifying colors (e.g. green part of red and blue
part of red) modify the x and y value and change the hue of that color.
At the same time the main colors also are used to control the color of
the white point.

Hot-Key Settings

Assign a different function to the hot-key on the remote control by highlighting
the function in the list and pressing ENTER. Choose a function that does not
already have a dedicated button, and assign the hot-key to that function,
allowing you to quickly and easily use the chosen function.

Service

• Projector Info: Display current projector settings (read-only).

• Factory Reset: Restore all settings to their default value. It will not reset

network but it will reset RS232.

• Test Pattern: Choose the desired internal test pattern to display, or select

OFF to turn off a test pattern.

• Phosphor Index: The Phosphor index synchronizes the phosphor wheel

with the filter wheel and DMD. The index defines the delay between the
wheel and the DMD. When the Phosphor index is adjusted, it will impact
the smoothness and contouring of the R/G/B gray level.

• Filter Index: The Filter index synchronizes the filter wheel with the phosphor

wheel and DMD. The index defines the delay between the wheel and the
DMD. When the filter index is adjusted, it will impact the smoothness of the
white color space without contouring, similar to the phosphor index
behavior.

• Error log: Show the projector error log for debug.

• Mode Adjustment: Fine tune the H and V start position for a signal in the

EDID timing table and record the values in the system to override the timing
table. The settings must be "Saved to Record" before exiting the menu, or
they will be lost. To revert to original timing table settings, each setting must
be manually cleared. Factory Defaults will not clear these override settings.

• Laser Diode Info: Display current laser banks status and temperature

information.

• High ambient temperature warning: Show the warning message the when

the ambient temperature is over 35°C.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-14

Section 4: OPERATION

4.4 Light Source

Light Source Mode

Select Constant Power, Constant Intensit y or ECO mode. When i n ECO mode,
the projector will adjust to the lowest fan speed and switch the laser diode
power to the minimum setting.

Constant Power

Set the value of the laser diode power (in Watts).

Constant Intensity

Set the value for the Constant Intensity to maintain constant brightness.
The light sensor will monitor the light level and will apply more power as the

laser brightness decays naturally over time. When the laser setting reaches
maximum power of 405W, it will remain at this setting. Note that the light
sensor needs to be calibrated for Constant Intensity mode to work properly.
Calibration should be performed again after every lamp change.

Total Projector Hours

Display current total hours the projector used.

Light Sensor

Calibrate light sensor.

4-15

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4.5 Status Menu

The read-only Status menu lists a variety of details about the standard and
optional components currently detected in the projector.

For DHD Models

Section 4: OPERATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-16

Section 4: OPERATION

For DWU Models

4-17

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

For DWX Models

Section 4: OPERATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-18

Section 4: OPERATION

4.6 Input Switching & PIP Menu

Main Input

From the list of active inputs, select one to be used as the main image.

PIP/PBP Input

From the list of active inputs, select one to be used as the PIP/PBP.

PIP/PBP Enable

Toggle between displaying two sources at once (Main and PIP/PBP images) or
one source only. The check box turns the PIP/PBP source ON and OFF. Refer
to Section 6.2 for the Main and PIP/PBP compatibility table.

Swap

Change the main image to PIP/PBP, and the PIP/PBP to main image.
Swapping is available only when PIP/PBP is enabled.

Size

Select the PIP/PBP size to small, medium or large.

Layout

Set the location of the PIP/PBP image on the screen.

4-19

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

NOTE:

P

P

P

P

P

P

P

P

P

P

P

P

PPP

P

P

P
P

P

 PIP/PBP layout and size table as described below.
 P : indicates primary source region (lighter color).
 * : Both source regions are the same size.

PIP/PBP Layout

Section 4: OPERATION

PIP/PBP Size

Small Medium Large

PBP, Bigger Left

Over-Under, Bigger Upper

PBP, Bigger Right

Over-Under, Bigger Lower

PIP-Bottom Right

PIP-Bottom Left

PIP-Top Left

P

PIP-Top Right

P

*

*

*

*

P

P

Timing Detection

Select timing detection mode to wide or normal. It is used to support additional
PC timings. When the projected picture is not completed, this function is used
to adjust the picture. "Normal mode" can support all of the 4:3 input sources.
"Wide mode" can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (example

1400 x 1050), perform Auto Image using "normal mode".

Source Info

Display current source settings (read-only).

Enable Source Hot-Key

Toggle the check box to enable or disable the main source hot-key.

Source Hot-Key

Allows you to assign a different source to the hot-key. Highlight an input and
press ENTER to choose a different one.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-20

Section 4: OPERATION

Input Key

Use it to list all of the sources or change the sources.

Blank on Signal Switch

When the function is enabled, the projector will blank the scre en before timing
is stable when change source.

4.7 Language Menu

Allows you to select an available language for the OSD display.

4.8 Test Pattern Menu

Choose the desired internal test pattern to display, or select OFF to turn off a
test pattern.

• OFF

• Black

• White

• Checkerboard

• Grid

• Color Bars

4-21

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4.9 Web User Interface

4.9.1 Logging On

Open your web browser and type the IP address (in the address bar) assigned
to your projector.

1 Select the log in level from the Access type drop-down list
2 Enter the Password in the Password field
3 Select the appropriate language from the Language drop-down list.
4 Click the Press login button. The Main window appears.

Section 4: OPERATION

4.9.2 Main Tabbed Page - General

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-22

Section 4: OPERATION

• Control Panel
Select main source / PIP source, enable/disable PIP/PBP, change the

layout / PIP size, swap, and change the test pattern.

• Projector Information Panel
Check the projector information for power status, Pic mute status, OSD

status, IP address and Mac address.

• Switch Panel
Switch the on/off status of power, Pic mute, and OSD.

4.9.3 Main Tabbed Page - Status

Display the current status of light source, cooling (fans), version numbers and
signal (source) information

4-23

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

4.9.4 Main Tabbed Page - Lens

Control the focus, lens shift and zoom adjustments for the lens.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-24

Section 4: OPERATION

4.9.5 Network

4-25

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

• Restart Network

Execute a Network restart. This will not change any of the network settings.

• Network Factory Reset

Execute a network factory reset. Network settings will be reset to the
following default values:

- Projector Name = Christie@ + Serial Number

- Show Network Messages = ON

- LAN Settings:

- Manual

- IP Address = 192.168.0.100

- Subnet Mask = 255.255.255.0

- Default Gateway = 192.168.0.100

- WLAN Se ttings:

- Enabled

- Start IP = 192.168.1.100

- End IP = 192.1 68.1.120

- Subnet Mask = 255.255.255.0

- Default Gateway = 192.168.1.100

- SNMP Settings:

- SNMP Read Communication = private

- Trap IP Address = 0.0.0.0

- SMTP IP Address = 0.0.0.0

- All other settings are cleared/blanked

- Trap Configuration:

- All items = SNMP Trap + Email

• LAN Setting Panel

- Select if the projector must obtain an automatically assigned IP address
through DHCP or if the user will set the address manually.

- Enter the IP address, netmask, and default gateway address for the
TCP/IP setting.

• WLAN Setting Panel

- Select if the wireless LAN of the projector is enabled or disabled.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-26

Section 4: OPERATION

- Enter the IP address range, netmask and default gateway for the wire­less LAN.

• SNMP Panel

- The SNMP (Simple Network Management Protocol) interface provides
network administrators with a common way to manage their network
devices from a single remote location. SNMP allows an administrator to
query a number of devices to see their current status/ configuration. It
also allows operators to change configuration values and configure trap
notifications to be sent when certain events occur. (eg. Loss of signal,
power state change, etc)

 Emails are sent to the mail server configured in the projector

settings. Up to 2 user email accounts can be selected. Any
important information regarding the event will be located in the body
content of the email.

 SNMP Traps are notifications that are sent from the projector. They

are only received by a trap receiver (MIB Browser) in the computer.

- SNMP Read Community (default setting: private) - this is a plain- text
password. This must also be entered in the MIB browser. This pass­word allows the various settings in the projector to be queried.

- SNMP Location (default setting: blank) - This field can be used as a
description to where a projector is located in a building. SNMP emails
sent will specify this location.

- Trap IP Address (default setting: 0.0.0.0) - This field must be filled in to
receive Traps from the projector . The Trap IP Address should be filled in
with the IP Address of the computer on which you would like to view
received traps.

- Trap Email 1/2 (default setting: Blank) - The Trap Email 1 and 2 must be
set to an email address that is configured under the mail server that you
will enter in the "SMTP Server IP Address" field.

- Email from Address (default setting: blank) - the "Email from Address"
that will appear as the source of the SNMP emails.

- SMTP Server IP Address (default setting: 0.0.0 .0 ) - Enter your mail
server's IP address.

• Trap Configuration Panel
Set the SNMP actions for the system events. The dropdown options are:

SNMP Trap + Email, Email, SNMP Trap, and Disabled.

• Crestron Control System Panel
Enter the IP address, IP ID, and Port of Crestron device for connection.

4-27

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

4.9.6 Tools

To Use the Tools tabbed pages to control "Size & Position", "Image Settings",
"Configuration", "Light Source", "Input Switching & PIP" and "Test Pattern.

4.9.7 Administrator Page

Add or delete a user or change password

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-28

Section 4: OPERATION

4.9.8 About Page

• Version Tab
View the main firmware version, network firmware version, projector model

name, and projector serial number.

• License Tab
The license information of the comp uter program is displayed.

4-29

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4.10 Christie Presenter

K

HDBaseT REMOTE

IN

GREEN/Y BLUE/PB RED/PR RS232 USB

MINI USB

ETHERNET CVBS S-VIDEO

REMOTE
OUT

HDMI VGA IN VGA OUT DISPLAY PORT DVI

The Christie Presenter application allows a remote desktop from a host PC to
be displayed on the network display through Ethernet, USB, or wireless
transports. It can adapt to different network settings (DHCP, fixed IP, and direct
link by USB/Ethernet cable).
Christie Presenter can be downloaded from the Christie website or from the
web page of the projector.

4.10.1 Connect to the Projector

1. Connect to the projector using WiFi or Ethernet

- Ethernet connection:
 Determine the projec tor's IP address from the menu Main Menu >

Configuration > Communications > LAN

 Configure your PC IP address to be on the same network as the

projector.

 The projector and computer must be connected directly or over the

network via Ethernet.

- WiFi Wireless connection:
 Insert the WiFi USB dongle (1DWUSB-BGN) into the USB port on

the projector input panel.

Section 4: OPERATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Insert the WiFi USB dongle

4-30

Section 4: OPERATION

 Power on the Projector.
 Obtain the WiFi SSID from the OSD menu Main Menu >

Configuration > Communications > WLAN

 Connect your PC device to the wireless SSID for the selected

projector . Example: "Christie@0111000123".

4.10.2 Install Christie Presenter software

1. Use a web browser to connect to the projector's network address (Default
address 192.168.1.100)

2. Download and install the Christie Presenter Software

4-31

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

3. Configure the Christie Presenter Software. The name entered is used to

identify all computers connected to the projector via the Christie Presenter
software via either wired or wireless connections. The Network Display
Management -> Device Management tab will show all current connections.

4.10.3 Use Christie Presenter

1. Press the autorun icon in the system tray to pause or play the USB display.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-32

Section 4: OPERATION

2. After starting the Christie Presenter application, the main window can been
seen (shown below).

Icon Description

Connect and search network display

Stop/start displaying desktop contents to
connected network display

Select display region

Configure Christie Presenter

Manage all connected network displays

Disconnect all connections

4-33

Connect and search network display

1 Click the button to enter into the connection menu section.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

2 If the IP address of the projector is known, enter the IP address and

click the "Connect" button. If the IP address is not known, click the
"Search" button to search for the projector on the network and select
the projector to which you want to connect. Select the option "Directly"
in order to proceed to the log in interface.

3 Input "User type" and "Password" in the log-in interface. Select the

display port (the default is full screen). Obtain the " Normal " user's
password from the OSD menu Main Menu > Configuration >
Communications > WLAN.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-34

Section 4: OPERATION

Select display region

Once the connection is set up, click the button to select the size of
the projection region: FullScreen, FixedSize, or Alterable.

• FullScreen: The default capture mode turns to Full screen when the
program is launched. At that time, if screen capture starts, the image of the

whole screen is transferred to a remote network display.

• FixedSize: FixedSize mode allows the users to place a frame on the
desktop. Only the image enclosed inside the frame is transferred to remote

network display.

• Alterable: In Alterable mode the only region captured is the one enclosed
by the frame. The region can be enlarged or downsized by dragging the

eight small black squares scattered on eight edges of the frame.

4-35

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

Configure Christie Presenter

Click the button to configure Christie Presenter for Basic Setting
and Advanced Setting.

• Basic Setting: Select language, change the region size of fixed size

capture mode, and select if notification message popup is allowed.

• Advanced Setting: Select the quality of JPEG image, YUV sample format

and network port setting. (The "Fixed" port is Port 5900)

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-36

Section 4: OPERATION

Manage all connected network displays

Click the button to control all the users and all the projectors
connector to the same projector.

con

Icon Description

Administrator log in.

Normal user log in.

Device is connected.

4-37

Device is not connected.
The icon shows the current status and display

position of the local screen on the network
display. Click on the icon to change the di splay
position. A dialog box will appear.

Click this unlock icon to change the password.
(Password change to target network di splay. Only
an Administrator user can change the password.)

No response is expected when this icon is
clicked. If user log in as "Admin", the key icon can
be seen and the Presenter password can be
changed. If user log in as "Normal", the lock icon
can be seen and the Presenter password can't be
changed.

Disconnect from target network display.
Link for connecting to a target network display via

a webpage.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4.11 Card Reader Operation

There are four operation modes in the Card Reader application:

- USB Flash Devices Detection Screen

- Thumbn ail Display Mode

- Images Display Mode

- Images Slide Show Mode

1. USB Flash Device Detection Screen:

In this mode, the Card Reader application detects any USB flash devices
hot-plug events and displays the flash device icon. When the flash device is
removed from USB, the icon disappears. It is suggested that USB flash
devices should be removed only when the Card Reader is changed to the
USB Flash Devices Detection Screen state.

Section 4: OPERATION

2. Thumbnail Display Mode:

Press the Enter key to enter the Thumbnail Display Mode. Different photos
in different folders can be chosen. Press the Menu key to bring up the Card

Reader operation UI.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-38

Section 4: OPERATION

The user interface is designed to operate the card reader application with a
few keys (Enter/Left/Right/Up/Down).

The following buttons are supported in the user interface:

• Previous: Move the selected item left. (Go to previous page when this is the
leftmost item)

• Next: Move the selected item right. (Go to next page when this is the
rightmost item.)

• Display: Display the selected image or display the selected folder.

• Thumbnail: Enter the Thumbnail Display Mode.

• SlideShow: Enter the Slide Show Mode.

• NameOrder: Sort files/folders in name order.

• ExtendOrder: Sort files/folders in extended order.

• SizeOrder: Sort files/folders in size order.

• TimeOrder: Sort files/folders in time order.

• EXIF ON/OFF: Enable/Disable auto image rotate accordingly to EXIF
information.

• FileName ON/OFF: Enable/Disable filename display in Thumbnail Display
Mode.

3. Image Display Mode:
Press the ENTER key in the Thumbnail Display Mode to enter the Image

Display Mode; press the SlideShow key to enter the Slide Show Mode. The
Left/Right key is used to display the last/next image in the Image Display
Mode. In the Image Display Mode, press the ENTER key to quit from the

Image Display Mode and enter the Thumbnail Display Mode.
In the Slide Show Mode, press the ENTER key to enter the Image Display

Mode.

4-39

The alternative way to display image in the Image Display Mode or Slide
Show Mode is using the operation UI.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

The following operations are supported in the operation UI.

• Display: Enter the Image Display Mode.

• Thumbnail: Enter the Thumbnail Display Mode.

• SlideShow: Enter the Slide Show Mode.

• Actual Size: Display in actual size of the image.

• Best Fit: Display the image in best fit to the screen.

• EXIFDisp OFF/On: Enable/Disable EXIF information display.

• +90deg: Rotate 90 degree.

• -90deg: Rotate -90 degree.

4. Image Slide Show Mode:

The following operations are supported in the Slide Show Mode operation
UI.

• Stop: Stop Slide Show Mode.

• Next: Display next image.

• Previous: Display previous image.

• Delay 3/4/5: Slide Show delay in seconds.

• Slide Effect: Following modes are supported.

- Slide Right

-Blocks

- RightDown

- XLines

- Slide Up

- Ylines

- Repeat ON/OFF: Enable/Disable Slide Show Repeat Mode.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-40

Section 4: OPERATION

When the image can NOT be displayed due to memory limitation or can
NOT support image format, the specific image is displayed on the center of
the screen.

4-41

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 4: OPERATION

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

4-42

Section 5: TROUBLESHOOTING

5. TROUBLESHOOTING

If you are unable to resolve an issue using the information provided in this
section, contact your reseller or servi ce ce nter.

Problem Solution

- No image appears
on-screen

- Make sure all the cables and power conne ctions are
correctly and securely connected See "Installation".

- Check if the Light Status LED is in Green.

- Make sure you have removed the lens cap and the
projector is switched ON.

• Partial, scrolling or
incorrectly
displayed image

- Press "AUTO" on control panel or on remote control.

- If you are using a PC (for Windows 95, 98, 2000, XP,
Windows 7):

1. Click the "My Computer" > "Control Panel" and then

double - click "Display".

2. Select the "Settings" tab.

3. Verify that your display resolution setting is lower than

or equal to WUXGA (1920 × 1200).

4. Click on the "Advanced Properties" button. If the

projector is still not projecting the whole image, change
the monitor display:

4.1 Verify the resolution setting is lower than or equal to
WUXGA (1920 × 1200).

4.2 Select the "Change" button under the "Monitor" tab.

4.3 Click on "Show all devices". Next, select "Standard
monitor types" under the SP box; choose the
resolution mode you need under the "Models" box.

4.4 Verify that the resolution setting of the monitor
display is lower than or equal to WUXGA (1920 ×

1200).

5-1

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Problem Solution

Notebook Brand Function Keys

Acer [Fn]+[F5]
Asus [Fn]+[F8]
Dell [Fn]+[F8]
Gateway [Fn]+[F4]
IBM/Lenovo [Fn]+[F7]
HP/Compaq [Fn]+[F4]
NEC [Fn]+[F3]
Toshiba [Fn]+[F5]

Mac Apple

System Preference  Display 
Arrangement  Mirror display

- Partial, scrolling or
incorrectly
displayed image

- If you are using a Notebook:

1. Adjust resolution of the computer.

2. Press the keys listed below for your notebook
manufacturer to send signal out from notebook to
projector. Example: [Fn]+[F4]

Section 5: TROUBLESHOOTING

- If you experience difficulty changing resolutions or your

• The screen of the

- If you are using a Notebook PC
Notebook or
PowerBook
computer is not
displaying your
presentation

• Image is unstable
or flickering

• Image has vertical
flickering bar

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

- Use "Pixel Track" and "Pixel Phase" to correct it.

- Change the monitor color settin g on your computer.

- Use "Auto Image" to make an adjustment.

- Check and reconfigure the display mode of your graphic

monitor freezes, restart all equipment including the
projector.

Some Notebook PCs may deactivate their own screens
when a second display device is in use. Each of them has a
different method of reactivation. Please refer to your
computer manual for detailed information.

card to make it compatible with the projector.

5-2

Section 5: TROUBLESHOOTING

Problem Solution

• Image is out of
focus

- Make sure both lens caps (front and back) are removed.

- Adjust lens focus to fit.

- Make sure the proje c tion screen is between the required
distance.

• The image is
stretched when

displaying 16:9
DVD title

• Image is too small
or too large

- When you play anamorphic DVD or 16:9 DVD, the
projector will show the best image when the projector

display mode is set to 16:9 in the OSD.

- If you play 4:3 format DVD titles, please change the format
to 4:3 in the projector OSD.

- If the image is still stretched, you will also need to adjust the
aspect ratio by setting the display format as 16:9 (wide)
aspect ratio type on your DVD player.

- Adju s t lens zoom to fit.

- If it does not fill the screen properly, verify that the correct
lens is in use or change the position of th e projector.

5-3

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 5: TROUBLESHOOTING

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

5-4

Section 6: SPECIFICATIONS

6. SPECIFICATIONS

6.1 Inputs

Signal

Resolution

Type

640x350 85 ● ●

640x400 85 ●● ●

640x480 59 ●

640x480 60 ●● ● ●

640x480 72 ● ● ●

640x480 75 ●● ● ●

640x480 85 ● ● ● ●

720x400 85 ●● ●

768x480 60 ●

768x480 75 ●

768x480 85 ●

800x600 50 ●●

PC

800x600 56 ● ● ●

800x600 60 ●● ● ●

800x600 72 ● ● ●

800x600 75 ●● ● ●

800x600 85 ● ● ● ●

848x480 50 ●

848x480 60 ●

848x480 75 ●

848x480 85 ●

960x600 50 ●

960x600 60 ● ●

960x600 75 ●

NOTE:

 "RB" means "reduced blanking".

Frame Rate

(Hz)

HDMI VGA DisplayPort DVI Component S- video CVBS

6-1

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 6: SPECIFICATIONS

Signal

Resolution

Type

960x600 85 ●

1024x768 60 ●● ● ●

1024x768 75 ● ● ● ●

1024x768 85 ●● ● ●

1064x600 50 ●

1064x600 60 ●

1064x600 75 ● ●

1064x600 85 ●●

1152x720 50 ●

1152x720 60 ●

1152x720 75 ●

1152x720 85 ●●

1152x864 60 ● ● ●

PC

1152x864 70 ●● ●

1152x864 75 ● ● ●

1152x864 85 ●● ●

1280x720 50 ● ●

1280x720 60 ●● ● ●

1280x720 75 ● ● ● ●

1280x720 85 ●● ● ●

1280x768 60 ● ● ●

1280x768 75 ●● ●

1280x768 85 ● ● ●

1280x800 50 ●● ● ●

1280x800 60 ● ● ● ●

1280x800 75 ●● ●

1280x800 85 ● ● ●

Frame Rate

(Hz)

HDMI VGA DisplayPort DVI Component S- video CVBS

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6-2

Section 6: SPECIFICATIONS

Signal

Type

PC

Resolution

1280x960 60 ●● ●

1280x960 75 ● ● ●

1280x960 85 ●● ●

1280x1024 50 ● ●

1280x1024 60 ●● ● ●

1280x1024 75 ● ● ● ●

1280x1024 85 ●● ● ●

1360x768 50 ●

1360x768 60 ●

1360x768 75 ●

1360x768 85 ●

1366x768 60 ● ● ● ●

1400x900 60 ●● ● ●

1400x1050 50 ● ●

1400x1050 60 ●● ● ●

1400x1050 75 ● ● ●

1440x900 60 ●● ●

1440x900 75 ●

1600x900 60 ●

1600x1200 50 ●

1600x1200 60 ●● ● ●

1680x1050 50 ● ●

1680x1050 60 ●● ● ●

1680x1050 75 ●

1704x960 50 ●

1704x960 60 ●

1728x1080 50 ●

Frame Rate

(Hz)

HDMI VGA DisplayPort DVI Component S- video CVBS

6-3

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 6: SPECIFICATIONS

Signal

Resolution

Type

1728x1080 60 ●

1864x1050 50 ●

1864x1050 60 ●

PC

1920X1080 50 ●●

1920X1080 60 ● ● ●

1920X1200RB 60 ●● ● ●

1920X1200RB 50 ● ● ● ●

NTSC NTSC (M, 4.43) 60 ●●

PAL (B,G,H,I) 50 ● ●

PAL

SECAM SECAM (M) 50 ●●

EDTV

PAL (N) 50 ●●

PAL (M) 60 ● ●

480i 60 ● ● ● ●

576i 50 ●● ● ●

480p 60 ● ● ● ●

576p 50 ●● ● ●

Frame Rate

(Hz)

HDMI VGA DisplayPort DVI Component S- video CVBS

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6-4

Section 6: SPECIFICATIONS

Signal

Type

HDTV

Resolution

1080i 25 ● ● ● ●

1080i 29 ●● ● ●

1080i 30 ● ● ● ●

720p 50 ●● ● ●

720p 59 ● ● ● ●

720p 60 ●● ● ●

1080s 23 ● ●

1080s 24 ●●

1080p 23 ● ● ● ●

1080p 24 ●● ● ●

1080p 25 ● ● ● ●

1080p 29 ●● ● ●

1080p 30 ● ● ● ●

1080p 50 ●● ● ●

1080p 59 ● ● ● ●

1080p 60 ●● ● ●

Frame Rate

(Hz)

HDMI VGA DisplayPort DVI Component S- video CVBS

6-5

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6.2 PIP/PBP Compatibility

Section 6: SPECIFICATIONS

Main

PIP/PBP

HDMI - - - - - - ● ● ● ● ●

VGA - - - - - - ●●●● ●

Component - - - - - - ● ● ● ● ●

CVBS - - - - - - ●●●● ●

S-Video - - - - - - ● ● ● ● ●

HDBaseT - - - - - - ●●●● ●

DisplayPort ● ● ● ● ● ● - - - - -

USB A ●● ● ● ● ● ---- -

USB MINI-B ● ● ● ● ● ● - - - - -

RJ45 ●● ● ● ● ● -----

DVI-D ● ● ● ● ● ● - - - - -

● : PIP/PBP combinations are enabled

- : PIP/PBP combinations are disabled

HDMI VGA Component CVBS S-Video HDBaseT

Display-

Port

USB A

USB

MINI-B

RJ45 DVI-D

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6-6

Section 6: SPECIFICATIONS

6.3 Key Features

• WXGA 0.65" 1280 x 800 or HD 0.65" 1920 × 1080 resolution or WUXGA

0.67" 1920 × 1200 resolution

• Projection lens compatibility:

- Horizontal offset ranges: +/-30%

- Vertical offset ranges: +/-100% (WUXGA/WXGA) and +/-120% (HD)

NOTE:

 Measurements are based on industry standards where offset is calculated as a ratio of the number of pixels shifted up/

down to half the image size.

• Dual Processing Warp Module for edge blending and geometric correction.
(Optional)

• Wireless desktop display using wireless dongle (optional)

• SNMP traps and e-mail notifications

• 10-bit image processor electronics with modular design

• All video formats can be resized to full screen either horizontally or
vertically while maintaining aspect ratio

• The projector can be operated using any of the following:

- The built-in keypad, an infrared (IR) remote control, a wired remote

control, a PC/device using serial communications (Ethernet or RS232)

- A Web page via Ethernet or from a PC/device via a wireless USB

dongle. (Optional)

• Weight:

- Maximum product weig ht (with lens removed): 15kg (33lb.)

• Built-In keypad

6-7

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6.4 List of Components

This projector comes with all the items shown below. Check to make sure your
package is complete. Contact your dealer if anything is missing.

• IR remote control 003-004468-01

• Power cord x 4

- UK/Korea/Russia

- North America

- Europe

-Japan

• DVI to HDMI dongle

• User manual (CD)

NOTE:

 Due to the difference in applications for each country, some regions may have different accessories.

6.5 Optional Accessories

• Cable cover (140-103105-01)

• Standard Lens (A05) (140-100102-01)

• Optional Lens (A01) (140-101103-01)

• Optional Lens (A03) (140-102104-01)

• 1DWUSB-BGN / Wireless dongle (optional accessory) (133-113106-01)

• Dual Processor Warp Module (optional accessory) (133-111104-01)

• Portrait Side Cover (140-108100-01)

Section 6: SPECIFICATIONS

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6-8

Section 6: SPECIFICATIONS

6.6 REGULATORY

• Safety

- CSA C22.2 No. 60950-1

- UL 60950-1

- IEC 60950-1

- EN 60950-1

• Electro-Magnetic Compatibility

Emissions

- FCC CFR47, Part 15, Subpart B/ANSI C63.4, Class A - Unintentional

-Radiators

- CISPR 22/EN 55022 Class A - Information Technology Equipment

- ICES/NMB003 (A) - Information Technology Equipment

Immunity

- CISPR 24/EN 55024 EMC Requirements - Information Technology

Equipment

• Environmental

• The product conforms to:

- EU Directive (2011/65/EU) on the restriction of the use of certain

hazardous substances (RoHS) in electrical and electronic equipment
and the applicable official amendment(s).

- EU Regulation (EC) No. 1907/2 006 on the registration, evaluation,

authorization and restriction of chemicals (REACH) and the applicable
official amendment(s).

- EU Directive (2012/19/EU) on waste and electrical and electronic

- equipment (WEEE) and the applicable official amendment(s).

- China Ministry of Information Industry Order No.39 (02/2006) on the

control of pollution caused by electronic information products, the
hazardous substances concentration limits (SJ/T11363-2006), and the
applicable product marking requirement (SJ/T11364-2006).

• Marking

- This product conforms to all relevant Canadian, US, and European

directives, standards, safety, health and environmental concerns.
International packaging recycling marks conform to:

 EU Directive (2012/19/EU) on waste and electrical and electronic

equipment (WEEE) .

 EU Directive (94/62/EC) on packaging and packaging waste
 China packaging recycling mark standard (GB18455-2001)

6-9

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 6: SPECIFICATIONS

WARNING

6.7 Federal Communications Commission (FCC) Warning

• A shielded-type power cord is required in order to meet FCC emission limits

and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used.

• Use only shielded signal cables to connect I/O devices to this equipment.

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6-10

Section 6: SPECIFICATIONS

6.8 OSD Tree

Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default

Size Presets

Overscan

Pixel Track 0 - 100 50

Pixel Phase 0 - 100 50
Horz Position 0 - 100 50
Vert Position 0 - 100 50

Digital Horz Zoom 50%~400% 100

Digital Vert Zoom 50%~400% 100
Digital Horz Shift 0 - 100 50

Digital Vert Shift 0 - 100 50

Size & Posi-

tion

Geometry Correc-

tion

Auto

Native

4:3

Letterbox

Full Size
Full Width
Full Height

Custom

Off

Crop

Off Off

Horz Keystone

Vert Keystone

Horz Pincushion 0 - 100 50

Vert Pincushion 0 - 100 50

Pincushion/Barrel 0-20 10

Basic

4-Corner

Curve

Curve

4-Corner

0 - 100

(0-20 for GEO

model)
0 - 100

(0-20 for GEO

model)

Top Left Horz

adjust.

Top Left Vert

adjust.

Top R ight Horz

adjust.

Top Right Vert

adjust.

Bottom Left Horz

adjust.

Bottom Left Vert

adjust.

Bottom Right

Horz adjust.

Bottom Right Vert

adjust.

Top Arc 0-300 150

Bottom Arc 0-300 150

Left Arc 0-300 150

Right Arc 0-300 150

Top Left Horz

t.

jus

ad

Top Left Vert

adjust.

Top R ight Horz

adjust.

Top Right Vert

adjust.

0-140 0

0-80 0

0-140 0

0-80 0

0-140 0

0-80 0

0-140 0

0-80 0

0-140 0

0-80 0

0-140 0

0-80 0

By source setZoom

(10 for GEO

(10 for GEO

Auto

50

model)

50

model)

6-11

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 6: SPECIFICATIONS

Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default

Curve 4-Corner

Rotation 0-16 8

tion

Geometry Correc-

tion

Rotate

Auto Image

Brightness 0 - 100 50

Contrast 0 - 100 By source set

Color Space

Detail

Video Options

In

put Levels

Auto Auto

RGB

YUV

Maximum

High

Normal

Low

Minimum

Color 0 - 100 50

Tint 0 - 100 50
Noise Reduction 0 - 100 0
Flesh Tone Cor-

rection

Video Black Level

Detect Film Off/On Off

Closed captions

Red Gain 0 - 100 50

Green Gain 0 - 100 50

Blue Gain 0 - 100 50

Red Offset 0 - 100 50

Green Offset 0 - 100 50

Blue Offset 0 - 100 50

Sync Threshold 0 - 100 50

Reset RGB Gain/

Offset

4-Corner

RGB

REC709
REC709
REC601

0 - 100 0

cc

Size & Posi-

Image settings

Off

2

Bottom Left Horz

adjust.

Bottom Left Vert

adjust.

Bottom Right

Horz adjust.

Bottom Right Vert

adjust.

Top Left Horz

adjust.

Top Left Vert

adjust.

Top R ight Horz

adjust.

Top Right Vert

adjust.

Bottom Left Horz

adjust.

Bottom Left Vert

adjust.

Bottom Right

Horz adjust.

Bottom Right Vert

adjust.

0-140 0

0-80 0

0-140 0

0-80 0

0-140 0

0-80 0

0-140 0

0-80 0

0-140 0

0-80 0

0-140 0

0-80 0

RGBRGB Video

REC709

By source set

Offcc1

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6-12

Section 6: SPECIFICATIONS

Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default

Picture Settings

Save to User

Image Freeze Off / On Off

Image settings

Advanced Image

Settings

Language English

Lens settings

Ceiling Mount Off/On/Auto Auto

Configuration

Rear Projection Off/On Off

Menu Preferences

Presentation

Video
Bright

Real

DICOM SIM

User

Video

Gamma

White Peaking 0 - 100 By source set

Color Tempera-

ture

Edge Enhance-

ment

Color Enhance-

ment

Focus command

Zoom command

Lens Shift command

Lock all Lens

Motors

Lens center cali-

bration

Menu Horz Offset 0 - 100 0

Menu Vert Offset 0 - 100 0
Show Messages off/on

Menu Transpar-

ency

Splash Screen

Setup

PIN Protect command
Change PIN command

Film

Bright

CRT

DICOM

Warmest

Warm

Cool

Bright

Off

Maximum

Off

CE 2

Allow

Locked

command

0 - 90 0

Factory Logo

Blue
Black
White

By source set

By source set

By source set

OffNormal

OffCE 1

Allow

Factory Logo

6-13

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 6: SPECIFICATIONS

Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default

Standby Mode

AC Power On off/on Off

Configuration

Power Manage-

ment

High Altitude Off/On Off

Communications

Image Blending

Auto shutdown

Sleep Timer

LAN

WLAN

Network

Serial Port Baud

Rate

Serial Port Echo Off/On Off

Serial Port Path

Projector Address 0 - 9 0

Blending On/Off Off

Marker On/Off Off

Grid

Solid Color

0.5 W Mode

Communication

Mode

Never

5 Mins
10 Mins
15 Mins
20 Mins
25 Mins
30 Mins

Off
2 Hrs
4 Hrs
6 Hrs

DHCP

IP Address

Subnet Mask

Default Gateway

MAC Address

Enable
Start IP
End IP

Subnet Mask

Default Gateway

MAC Address

SSID

Password

Projector Name

Show Network

Messages

Restart Network…

Network Factory

Reset…

2400
4800
9600

14400
19200
38400
57600

115200

1200

RS232

HDBaseT

Off/White/Red/

Green/Blue

Off/White/Red/

Green/Blue

Communication

mode

20 Mins

Off

by set

by set

by set

115200

RS232

Off

Off

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6-14

Section 6: SPECIFICATIONS

Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default

TOP

Bottom

Left

Right

Blending Area off-

set

non-Blending

Area Offset

Enable On/Off Off

Auto Test Pattern On/Off On

Measured Data

Target Data

Enable On/Off Off

Auto Test Pattern On/Off On

Red Part of Red 0 - 1000 1000

Green Part of Red 0 - 1000 0

Blue Part of Red 0 - 1000 0

Green Part of

Green

Red Part of

Green

Blue Part of

Green
Blue Part of Blue 0 - 1000 1000
Red Part of Blue 0 - 1000 0

Green Part of Blue 0 - 1000 0

Configuration

Image Blending

Color Matching

Overlap

Bright Adj.

Drop Off Curve 70-300 100
Image Gamma 1.8/2.0/2.2/2.4/2.6 2.2

Meter Adjustment

Manual Adjust-

ment

0… ½ Output
Height(Pixel)

0… ½ Output

Height

0… ½ Output

Width

0… ½ Output

Width

0-2000 1000

0-2000 1000

Intensity of Red 100 - 10000 544

x of Red 0.300 - 0.700 0.590
y of Red 0.300 - 0.500 0.383

Intensity of Green 100 - 10000 2103

x of Green 0.300 - 0.400 0.314
y of Green 0.400 - 0.700 0.620

Intensity of Blue 100 - 10000 124

x of Blue 0.100 - 0.300 0.146
y of Blue 0.030 - 0.400 0.030

Intensity of White 100 - 10000 6772

x of White 0.200 - 0.400 0.305
y of White 0.200 - 0.400 0.333

Reset to Default Yes/No

Gain of Red 0.200 - 1.000 1.000

x of Red 0.300 - 0.700 0.615
y of Red 0.300 - 0.500 0.381

Gain of Green 0.200 - 1.000 1.000

x of Green 0.300 - 0.400 0.308
y of Green 0.400 - 0.700 0.633

Gain of Blue 0.200 - 1.000 1.000

x of Blue 0.100 - 0.300 0.142
y of Blue 0.030 - 0.400 0.030

Gain of White 0.200 - 1.000 1.000

x of White 0.200 - 0.400 0.328
y of White 0.200 - 0.400 0.380

Reset to Default Yes/No

0 - 1000 1000

0 - 1000 0

0 - 1000 0

0

0

0

0

6-15

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 6: SPECIFICATIONS

Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default

Color Matching

Hot-Key settings

Configuration

Service

Manual Adjust-

ment

Blank Screen

Aspect Ratio

Freeze Screen

Projector Info

Overscan

Closed Captions

Projector Info

FactoryReset…

Test pattern

Phosphor Index

Filter Index

Error log

Mode Adjustment

Laser Diode Info

High ambient tem-

perature warning

Red Part of White 0 - 1000 1000

Green Part of

White

Blue Part of White 0 - 1000 1000

Reset to Default Yes/No

Model Name

Serial Number

Native Resolution

Firmware

Configuration

Boot Code
Standby Mode
Lens Lock Set-

tings

Wheel Index

Off

Grid

White

Black

Checkerboard

Color Bars

Red

Green

Blue

Yellow

Magenta

Cyan

Boresight

Show log
Clear log

LD1 Voltage
LD2 Voltage
LD3 Voltage
LD4 Voltage
LD5 Voltage

Bank1 tempera-

ture

Bank2 tempera-

ture

On/Off On

0 - 1000 1000

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6-16

Section 6: SPECIFICATIONS

Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default

Light Source Mode

Constant Power 243 - 405

Light Source

Constant Intensity 0 - 10 7

Total Projector

Hours

Light Sensor

Model Name

Serial Number

Native Resolution

Firmware Vxx, Ayy, Bzz

Main Input

Main Signal Format

Main Pixel Clock

Main Sync Type

Main Horz Refresh

Main Vert Refresh

PIP/PBP Input

PIP/PBP Signal

Format

PIP/PBP Pixel

Status

Clock

PIP/PBP Sync

Type

PIP/PBP Horz

Refresh

PIP/PBP Vert

Refresh

Light Source Power

Total Projector

Hours

Standby Mode

Lens Lock Settings

IP Address

DHCP

System Tempera-

ture

Constant Power/

Constant Inten-

sity/Eco mode

Light Sensor Cali-

bration

Calibrated? (display Yes/No)

Constant Power

243, 259, 275,
292, 308, 324,
340, 356, 373,

389, 405

6-17

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 6: SPECIFICATIONS

Level 1 Level 2 Level 3(Or List) Level 4(Or List) Level 5(Or List) Level 6(Or List) Default

Input Switch-

ing & PIP

Language English

Test pattern

Main Input SPEC define

PIP/PBP Input SPEC define

PIP/PBP Enable

Swap

Size

Main Layout

Timing Detection

Mode

Source Info

Enable source Hot-

Key

Source Hot-Key

Input key

Blank on Signal

Switch

Off

Grid
White
Black

Checkerboard

Color Bars

OFF

(Small/Medium/

Large)

(PBP, Main Left /

PBP, Main Top /

PBP, Main Right /

PBP, Main Bot-

tom / PIP-Bottom

Right / PIP-Bot-

tom Left / PIP-Top

Left / PIP-Top

Right)

Normal

Wide
Active Source
Signal Format

Aspect Ratio

Resolution
Vert Refre sh
Horz Refresh

Pixel Clock

Sync Type

Color Space

PIP/PBP

<PIP/PBP source

lines>

OFF

VGA Key number 1
HDMI Key number 2
DVI-D Key number 3

Display Port Key number 4
Component Key number 5

S-Video Key number 6

Composite Key number 7

Christie Presenter Key number 8

Card Reader Key number 9

Mini USB Key number 0

HDBaseT

Change Sources

Auto Source

OFF

ON

(When PIP/PBP

active)

(When PIP/PBP

ON

ON

active)

Auto SourceList all Sources

OFF

Wide

ON

OFF

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6-18

Section 6: SPECIFICATIONS

OSD Gamma index

CRT 6

VIDEO 5

FILM 0

BRIGHT 4

DICOM 13

6.9 Preset Mode tables

Orion-Laser projector

Descrption Bright Presentation Video Dicom Real

PW 2X 2X 2X 2X 2X
CW 2X 2X 2X 2X 2X

Syt. mode number 0 6 6 6 6

color temperature Warm Bright Warm Warm Warm

Bright
Warm

Warmest

Cool

Gamma Video Video Video Dicom FILM

White peaking 100 100 100 100 100

Please see below table for DWU/DHD & DWX

6-19

Mode

NO.

SQ CT mode OSD mode CT

0 Bright 2X-Native Bright Warm
0 Bright 2X-D55 Bright Warmest
0 Bright 2X-D70 Bright Bright
0 Bright 2X-D80 Bright Cool
1 Presentation 2X-Native Presentation Bright
1 Presentation 2X-D65 Presentation Warm
1 Presentation 2X-D55 Presentation Warmest
1 Presentation 2X-D85 Presentation Cool
2 Video 2X-Native Video Warm
2 Video 2X-D55 Video Warmest
2 Video 2X-D75 Video Bright
2 Video 2X-D85 Video Cool
3 Real 2X-Native Real Warm
3 Real 2X-D55 Real Warmest
3 Real 2X-D75 Real Bright
3 Real 2X-D85 Real Cool

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

Section 6: SPECIFICATIONS

SIGNAL

Composite

S-video

VGA/PC

HDMI/DVI/

HDBaseT

Default

Mode

Video
Mode

Video
Mode

Presenta­tion Mode

Presenta­tion Mode

Bright

Contr

IMAGE Mode

Presentation

Mode

Video Mode 50 50 Vi deo Mode 50 50

PAL

Bright Mode 50 50 Bright Mode 50 50

Real Mode 50 50 Real Mode 50 50
Dicom Mode 50 50 Dicom Mode 50 50
Presentation

Mode

Video Mode 50 50 Video Mode 50 50

PAL

Bright Mode 50 50 Bright Mode 50 50

Real Mode 50 50 Real Mode 50 50
Dicom Mode 50 50 Dicom Mode 50 50
Presentation

Mode

Video Mode 50 50 Video Mode 50 50

PC Sig-

nal

Bright Mode 50 50 Bright Mode 50 50

Real Mode 50 50 Real Mode 50 50
Dicom Mode 50 50 Dicom Mode 50 50
Presentation

Mode

Video Mode 50 50 Video Mode 50 50

PC Sig-

nal

Bright Mode 50 50 Bright Mode 50 50

Real Mode 50 50 Real Mode 50 50
Dicom Mode 50 50 Dicom Mode 50 50

ness

50 50

50 50

50 50

50 50

Default

ast

Presen-

IMAGE Mode Brightness Contrast

Mode

Video
Mode

Video
Mode

Video
Mode

tation
Mode

NTSC

NTSC

Component/

Video

(720p,576p/I,

1080p/i…)

HDMI/DVI

(SD/HD)

Presentation

Mode

Presentation

Mode

Presentation

Mode

Presentation

Mode

50 50

50 50

50 50

50 50

GS Series User Manual

020-000724-01 Rev. 1 (05-2014)

6-20