Christie DHD1075-GS, DWU1075-GS User Manual

User Manual

020-001225-03

GS Series

DHD1075-GS/DWU1075-GS

The USB included with this printed manual contains an electronic copy in English. Please read all instructions before using or servicing this product.

手册中包含的 U 盘，带有着中文的电子副本，使用或维修本产品前，请仔细查阅所有的指示。

Le clé USB fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les instructions avant d'utiliser ou de réparer ce produit.

Das USB, das mit diesem gedruckten Handbuch eingeschlossen ist, enthält eine elektronische Kopie auf in deutscher Sprache. Vor der Anwendung oder der Instandhaltung dieses Produktes lesen Sie bitte alle Anweisungen.

Il USB fornito con il manuale stampato contiene una copia elettronica in lingua italiano. Si prega di leggere tutte le istruzioni prima di utilizzare o riparare questo prodotto.

この印刷されたマニュアルに同梱されております USB には、日本語での説明書が入っております。この製品を使用あるいは修理点検される際に、ご参照下さい。

매뉴얼과 함께 포함되어 있는 USB 에는 한글로 된 전자사본을 포함하고 있습니다 . 본 제품을 사용 혹은 서비스하기 전에 모든 지침 사항들을 읽어 보시기 바랍니다 .

Поставляемый в комплекте с документацией USB содержит электронную копию руководства пользователя на русском языке. Перед началом использования изделия или проведения сервиса пожалуйста прочтите все инструкции изложенные в руководстве.

El USB incluido con este manual impreso contiene una copia electrónica en español. Por favor, lea todas las instrucciones antes de usar o dar servicio a este producto.

USB, що постачається з цим друковане керівництво містить електронну копію українською мовою. Будь ласка, прочитайте всі інструкції перед використанням або обслуговуванням цього продукту.

O USB incluído com o impresso livro contém um eletrônico cópia em Português. Por favor lido todas as instruções antes de usar ou prestando serviço esse resultado.

NOTICES

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material. Canadian manufacturing facility is ISO 9001 and 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or Christie. In addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your product, the warranty does not cover:

a. Problems or damage occurring during shipment, in either direction. b. Projector lamps (See Christie’s separate lamp program policy). c. Problems or damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp other than a

Christie lamp supplied by Christie or an authorized distributor of Christie lamps.

d. Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems,

cameras, DVD players, etc., or use of a product with any non-Christie interface device.

e. Problems or damage caused by the use of any lamp, replacement part or component purchased or obtained from an

unauthorized distributor of Christie lamps, replacement parts or components including, without limitation, any distributor offering Christie lamps, replacement parts or components through the internet (confirmation of authorized distributors may be obtained from Christie).

f. Problems or damage caused by misuse, improper power source, accident, fire, flood, lightening, earthquake or other

natural disaster.

g. Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie

service personnel or a Christie authorized repair service provider.

h. Problems or damage caused by use of a product on a motion platform or other movable device where such product has not

been designed, modified or approved by Christie for such use.

i. Problems or damage caused by use of a projector in the presence of an oil-based fog machine or laser-based lighting that is

unrelated to the projector.

j. For LCD projectors, the warranty period specified in the warranty applies only where the LCD projector is in “normal use”

which means the LCD projector is not used more than 8 hours a day, 5 days a week.

k. Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless

such product is protected from precipitation or other adverse weather or environmental conditions and the ambient

temperature is within the recommended ambient temperature set forth in the specifications for such product. l. Image retention on LCD flat panels. m.Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in accordance with the maintenance schedule specified by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s own expense.

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용 (A 급 ) 으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 , 가정 외의 지역에 서 사용하는 것을 목적으로 합니다 .

Environmental

The product is designed and manufactured with high-quality materials and components that can be recycled and reused.

This symbol means

that electrical and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the environment we live in!

Content

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Laser safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Light intensity hazard distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Projector components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Left view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Right view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Built-in keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Input/Output (I/O) panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

IR remote keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

LED status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Shutter LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Connecting to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Connecting to video equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Turning the projector on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Turning the projector off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Adjusting the projector position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Calculating the lens offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

WUXGA projectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

HD Projectors: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Removing and installing the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Installing the ceiling mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Installing the projector in the rigging frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Setup, alignment and test procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Size and Position menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Geometry correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Image Settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

GS Series 1075 User Manual 5 020-001225-03 Rev. 1 (02-2018)

Content

Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Color matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Light Source menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Status menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

For DHD models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

For DWU models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Input Switching & PIP menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

PIP/PBP layout and size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Language menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Test Pattern menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Web user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Logging on to the web user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Main tab–General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Main tab–Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Main tab–Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Administrator Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

About Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Christie Presenter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Connecting to the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Installing the Christie Presenter software . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Using the Christie Presenter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Connecting and searching the network display . . . . . . . . . . . . . . . . . . . . . . . . .64

Selecting the display region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Configuring Christie Presenter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Managing all connected network displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Operating the Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

No image appears on screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Incorrectly displayed image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Presentation is not displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Unstable or flickering images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Vertical flickering bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Image is out of focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Image is stretched . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Image is not the correct size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

GS Series 1075 User Manual 6 020-001225-03 Rev. 1 (02-2018)

Content

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

PIP/PBP compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

List of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83

Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Physical operating environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Regulatory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Laser safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Electro-Magnetic Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Federal Communications Commission (FCC) warning . . . . . . . . . . . . . . . . . . . . . . . 86

On-screen display tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

GS Series 1075 User Manual 7 020-001225-03 Rev. 1 (02-2018)

Safety

Read all safety and warning guidelines before installing or operating the projector. This projector must be operated in an environment that meets the operating range specification.

Use only the attachments and/or accessories recommended by Christie. Use of others may result in the risk of fire, shock, or personal injury.

Warning! Failure to comply with the following could result in death or serious injury.

• Do not look into the projector lens when the laser is on. The bright light may result in permanent eye damage.

• To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture.

• Do not open or disassemble the projector as this may cause electric shock.

• All installation and maintenance procedures must be performed by a Christie qualified technician.

• Keep all combustible material away from the concentrated light beam of the projector.

• Position all cables where they cannot contact hot surfaces or be pulled or tripped over.

• Always power down the projector and disconnect all power sources before servicing or cleaning.

• Disconnect the power plug from the AC outlet if the product is not being used for an extended period of time.

• Only use the AC power cord supplied. Do not attempt operation if the AC supply and cord are not within the specified voltage and power range for your region.

• Do not allow anything to rest on the power cord.

• Do not block the ventilation slots and openings on the projector.

Caution! Failure to comply with the following could result in minor or moderate injury.

• Only Christie qualified technicians are permitted to open product enclosures.

• FIRE HAZARD! Do not use a power cord or that appears damaged.

• FIRE OR SHOCK HAZARD! Do not overload power outlets and extension cords.

Notice. Failure to comply with the following may result in property damage.

• Use a soft cloth moistened with a mild detergent to clean the display housing.

• Remove the lens plug from the lens opening in the proje ctor before installing the lens. Retain the lens plug to protect the optical components from dust and debris during transport.

• Do not use abrasive cleaners, waxes, or solvents to clean the projector.

GS Series 1075 User Manual 8 020-001225-03 Rev. 1 (02-2018)

Safety

此產品可能會產生有害雷射光，請勿直視光束，避免對眼睛造成損害。

注意

1級雷射產品危險等級2

Pinching hazard

RG2 caution symbol

Laser safety warnings

This product is classified as CLASS 1 LASER PRODUCT - RISK GROUP 2 according to IEC 60825-1 : 2014 complies with FDA regulations 21 CFR 1040.10 and 1040.11 as a Risk Group 2 , LIP ( Laser Illuminated Projector) as defined in IEC 62471:2006 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.

Warning! Failure to comply with the following could result in death or serious injury.

• This projector has a built-in Class 4 laser module. Never attempt to disassemble or modify the projector.

• Any operation or adjustment not specifically instructed in the User manual creates the risk of hazardous laser radiation exposure.

• Do not open or disassemble the projector as this may cause damage or exposure to laser radiation.

• Do not stare into beam when the projector is on. The bright ligh t may result in permanent eye damage.

• When turning on the projector, make sure no one within projection range is looking into the lens.

• Follow the control, adjustment, or operation procedures to avoid damage or injury from exposure of laser radiation.

• The instructions for the assembly, operation, and maintenance include clear warnings concerning precautions to avoid possible exposure to hazardous laser radiation.

GS Series 1075 User Manual 9 020-001225-03 Rev. 1 (02-2018)

Safety

Light intensity hazard distance

This projector has been classified as CLASS 1 LASER PRODUCT - RISK GROUP 2 due to possible hazardous optical and thermal radiation being emitted.

Warning! Failure to comply with the following could result in serious injury.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! No direct exposure to the beam must be permitted. RG2 IEC 62471-5:2014.

• PERMANENT/TEMPORARY BLINDNESS HAZARD! Operators must control access to the beam within the hazard distance or install the product at the height (greater than or equal to 3.0 m from the floor to the beam) that prevents exposure of spectators' eyes within the hazard distance.

• EXTREME BRIGHTNESS! Do not place reflective objects in the product light path.

• Do not stare into beam when the projector is on. The bright ligh t may result in permanent eye damage.

GS Series 1075 User Manual 10 020-001225-03 Rev. 1 (02-2018)

Introduction

The 1075-GS Series is a high brightness, high-resolution video graphics one-chip laser-based projector. The projector is available in HD and WUXGA resolutions and uses Digital Light Processing

) technology from Texas Instruments. It is primarily designed for fixed installation and

(DLP secondary applications including rental-staging and LBE (Location Based Entertainment). This product is used for professional applications and is not for domestic use.

Projector components

Identify the main components of the projector.

Front view

Identify the main components on the front of the projector.

ID Part name Description

1 Front IR sensors Receives signals from the IR remote keypad. Keep the signal path to the sensor

unobstructed for uninterrupted communication with the projector.

2 Projection lens Allows automated lens control and adjustment: vertical and horizontal offsets,

zoom, and focus.

3 Adjustable feet Raises or lowers the feet to level the projector.

GS Series 1075 User Manual 11 020-001225-03 Rev. 1 (02-2018)

Introduction

4 5

Rear view

Identify the main components on the rear of the projector.

ID Part name Description

1 Rear IR sensor Receives signals from the IR remote keypad. Keep the signal path

unobstructed for uninterrupted communication with the projector. 2 Input/Output (I/O) panel Connects the projector to external devi ces. 3 Built-in keypad Controls the projector. 4 AC input Connects to the supplied power adapter. 5 Power button Powers the projector on or off. 6 Kensington Security Slot Secures the projector to help prevent theft or unauthorized removal.

GS Series 1075 User Manual 12 020-001225-03 Rev. 1 (02-2018)

Introduction

Left view

Identify the main components on the left side of the projector.

ID Part name Description

1 Cooling air vents (intake) Provides cooling to the projector. Keep these vents unobstructed to prevent

the projector from overheating.

Right view

Identify the main component on the right side of the projector.

ID Part name Description

1 Cooling air vents

(exhaust)

Provides cooling to the projector. Keep these vents unobstructed to prevent the projector from overheating.

GS Series 1075 User Manual 13 020-001225-03 Rev. 1 (02-2018)

Built-in keypad

11 12

2 3

The built-in keypad controls the projector.

ID Part name Description

1 Auto Automatically optimizes an image. 2 Power Turns the projector on or off. 3 Shutter Displays or blanks the video image.

Introduction

4 OSD Hides or shows the on-screen display (OSD) menus. 5 Help Displays the instructions for source connection. 6 Menu Displays the menus. 7 Arrow keys Adjusts a setting up or down, or navigates within a menu. 8 Input Selects an input for the main or PIP/PBP image. 9 Focus Adjust the focus. 10 Lens Adjusts the lens vertical or horizontal offset setting. 11 Zoom Adjusts the zoom. 12 Back Returns to the previous level or exits the menus if at top level.

GS Series 1075 User Manual 14 020-001225-03 Rev. 1 (02-2018)

Input/Output (I/O) panel

1213

12 564

141516

Rear view

Bottom view

Identify the components of the Input/Output (I/O) panel.

ID Connector name ID Connector name

13G-SDI OUT 9HDMI-2 2 3G-SDI IN 10 USB 3DVI-D IN 11MINI USB

Introduction

4 VGA IN 12 ETHERNET 5HDMI-OUT 133D SYNC IN 6HDMI-1 143D SYNC OUT 7REMOTE OUT 15HDBaseT 8 REMOTE IN 16 RS232

GS Series 1075 User Manual 15 020-001225-03 Rev. 1 (02-2018)

Introduction

SHUTTER

VGA

HDMI2 DVI-D

BNC

3G-SDI HDBaseT

PRESENT.

CVBS

HDMI1

16 17

18 19

26 27

1 2 3 4

8 9 10

11 12 13

IR remote keypad

The IR remote keypad communicates with the projector by way of wireless or wired connection. For wired connection, use a cable length of 20 m or less. If the length of cable exceeds 20 m, the IR

remote keypad may not work correctly.

ID Button Description

1 SHUTTER Displays or blanks the video image. 2 ON Turns the projector on. 3 Gamma Adjusts the mid-range levels. 4 BRIGHT Adjusts the amount of light in the image. 5 PIP/PBP Turns PIP/PBP on or off.

GS Series 1075 User Manual 16 020-001225-03 Rev. 1 (02-2018)

ID Button Description

6 SIZE Adjusts the PIP/PBP size.

Introduction

7 Number Keys Enters a number, such as a channel, value, and so on. The

on-screen display indicates if a function is not supported. 8 HELP Displays the instructions for source connection. 9 MENU Displays the menus. 10 Arrow keys Adjusts a setting up or down to navigate within a menu. 11 TEST Displays a test pattern. 12 AUTO Automatically optimizes an image. 13 OSD Uses to hide or shows on-screen display (OSD) menus. 14 KEYSTONE H Adjusts the horizontal keystone. 15 KEYSTONE V Adjusts the vertical keystone. 16 STANDBY Turns the projector off. 17 CONTR Adjusts the difference between dark and light. 18 HOT KEY Selects your preset key quickly. 19 SWAP Swaps the main and PIP/PBP images. 20 LAYOUT Adjusts the PIP/PBP layout. 21 FOCUS Adjust s the focus to improve image clarity as required. 22 ZOOM Adjusts the zoom to achieve a required image size. 23 PROJ Changes the IR remote keypad ID.

• To assign an ID, press Proj + <1 to 9>.

• To return to the universal IR remote ID, press Proj + 0. 24 EXIT Returns to previous level or exit menus if at top level. 25 ENTER Selects a highlighted menu item, or changes or accepts a

value. 26 INPUT Selects an input for the main or PIP/PBP image. 27 INFO Displays the source image information. 28 LENS H Adjusts the position of the image horizontally. 29 LENS V Adjusts the position of the image vertically.

GS Series 1075 User Manual 17 020-001225-03 Rev. 1 (02-2018)

Introduction

LED status indicators

LEDs are defined below.

Status LED

Identify the LED state colors and meaning.

LED status Projector state

Off AC power is off (without AC plugged in). Green (flashing) Projector is in startup or cool down mode. Green (solid) System is operating normally. Blue (flashing) Projector is cooling down. Blue (solid) AC has been applied, projector is in standby mode. Yellow (flashing) A problem exists with the projector that does not cause it to shut down.

Examples of warnings include: filter needs changing, one of the pumps is damaged,

or a fan is operating at full speed due to over temperature of LD driver. Yellow (solid) The end user is turning off the projector while it is in a warning state. Red (flashing) An error with the projector exists that has caused or may inevitably cause it to shut

Red (solid) The end user is turning off the projector while it is in an error state. White (flashing) Projector is in a flash (LAN) update state.

down.

Examples of errors include: fan failure, over temperature, wrongly installed filter,

color wheel (CW) failure.

Shutter LED

Identify the shutter LED state colors and meaning.

LED status Projector state

Off Projector is on and an image is displayed. Shutter is open. Magenta (solid) Projector is on and the image is blank. Shutter is closed.

GS Series 1075 User Manual 18 020-001225-03 Rev. 1 (02-2018)

Installation

3 4 52

Desktop Laptop

Learn how to install, connect, and optimize the projector display.

Connecting to a computer

Learn what cables/connectors that may be used to connect to various devices.

ID Connector name ID Connector name ID Connector name

1 RS232 cable 3 VGA IN cable 5 USB Type B mini cable 2 DVI-D IN cable 4 HDMI cable

• Due to the difference in applications for each country, the accessories required in some regions may differ from those shown.

• This diagram is for illustrative purposes only and does not indicate that these accessories are

GS Series 1075 User Manual 19 020-001225-03 Rev. 1 (02-2018)

supplied with the projector.

Connecting to video equipment

Component video output equipment DVD player Video cassette recorder

Learn what cable/connectors may be used to connect to various devices.

Installation

ID Connector name ID Connector name

1 DVI-D IN Cable 3 VGA IN Cable 2 VGA to Component 4 HDMI Cable

• Due to the difference in applications for each country, the accessories required in some regions may differ from those shown.

• This diagram is for illustrative purposes only, and does not indicate that these accessories are supplied with the projector.

GS Series 1075 User Manual 20 020-001225-03 Rev. 1 (02-2018)

Installation

Turning the projector on

The projector cables must be securely connected before turning the power on.

Warning! Failure to comply with the following could result in death or serious injury.

• Do not look into the projector lens when the laser is on. The bright light may result in permanent eye damage

1. Connect the projector power cables to AC power.

The Power button on the keypad is illuminated when the power cables are connected.

2. Ensure the lens has been installed in the projector.

3. Ensure that no one or no objects are in the beam path before turning on the projector.

4. To turn on the projector, on the IR remote keypad press or on the built-in keypad press .

The status LED is green with a slow blink.

5. To select an input source and turn it on, on the IR remote keypad select Input Key.

Available input sources are VGA, HDMI1, HDMI2, DVI, 3G-SDI, and HD-BaseT.

The projector detects the source you selected and displays the image.

Power on

SHUTTER

VGA

BNC

Power on

Input Key

HDMI2 DVI-D

3G-SDI HDBaseT

HDMI1

CVBS

PRESENT.

The first time the projector is used, select the preferred language from the Main menu after the startup screen is displayed.

Turning the projector off

Power off the projector in preparation for inspection or maintenance.

1. To turn the projector off, on the IR remote keypad or built-in keypad press .

A warning message appears on the displayed image.

GS Series 1075 User Manual 21 020-001225-03 Rev. 1 (02-2018)

Installation

2. To confirm your selection, press again.

If you do not press again, the warning message disappears after three seconds and the projector remains on.

Adjusting the projector position

When you select a position for the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Follow these general guidelines:

• Position the projector on a flat surface at a right angle to the screen. The projector (with the standard lens) must be at least 4.27 feet (1.3 m) from the projection screen.

• Position the projector to the required distance from the screen. The distance from the lens of

the projector to the screen, the zoom setting, and the video format determine the size of the projected image.

• Determine the lens throw ratio:

• Lens 0.75~0.95 (WU/HD)

• Lens 0.95~1.22 (WU/HD)

• Lens 1.22~1.53 (WU/HD)

• Lens 1.52~2.89 (WU/HD)

• Lens 2.9~5.5 (WU/HD)

• Lens 0.36 (120’’ screen, WU/HD)

• 360 degree free orientation operation

GS Series 1075 User Manual 22 020-001225-03 Rev. 1 (02-2018)

Installation

Lens center

0 %0 %

Calculating the lens offset

Adjust the offset to align the image on the screen with half image size.

• The vertical image offset (shift) ranges for the projector are +/-100% (WUXGA) and +/-120% (HD).

• The horizontal image offset (shift) range for the projector is +/-30% (HD/WUXGA).

• The method for calculating lens offset complies with industry standards. For example for vertical lens offset:

• At 0% offset (or on axis), the center of the image is on the lens center, so half of the image appears above and half appears below the lens center.

• At +100% offset, the entire of the image appears above the lens center.

• The percentage (%) offset is calculated as the ratio of the number of pixels shifted up or down to half image size.

UST lens do not support the lens shift function.

WUXGA projectors

The following show vertical image offsets for the WUXGA projectors:

• Vertical image offset: 0%

GS Series 1075 User Manual 23 020-001225-03 Rev. 1 (02-2018)

• Vertical image offset: +100%

+100%

Lens center

-100%

• Vertical image offset: -100%

Installation

GS Series 1075 User Manual 24 020-001225-03 Rev. 1 (02-2018)

HD Projectors:

Lens center

+120%

Lens center

-120%

The following show vertical and horizontal image offset for HD projectors:

• Vertical image offset: +120%

• Vertical image offset: -120%

Installation

GS Series 1075 User Manual 25 020-001225-03 Rev. 1 (02-2018)

• Horizontal image offset: +/-30%

Lens center

-30% 0% +30%0%

Installation

GS Series 1075 User Manual 26 020-001225-03 Rev. 1 (02-2018)

Installation

By hand With a tool

Removing and installing the lens

When handling the projector after lens installation, make sure the front lens cap is placed on the lens to protect the lens surface from potential damage. When carrying or moving the projector, do not handle by the lens. This may damage the lens, the chassis, or other mechanical parts within the projector.

1. Center the lens. Ensure the lens is at or near its center position. Attempting to remove the lens with a large offset may cause damage to the lens assembly.

Center the lens while the projector is switched on by pressing the Lens Horizontal or Lens Vertical button and then pressing Enter.

2. Turn off the projector.

3. Allow the projector to cool down into standby mode before replacing the lens.

4. After the projector has cooled down and prior to replacing the lens, remove the power cord.

5. To remove the lens, press the Lens Release button by hand or with a tool and rotate the lens counterclockwise by a quarter to release the lock.

6. Remove the lens through the front of the projector.

7. To install the new lens, fully insert the lens assembly straight into the lens mount without turning.

8. To lock the lens in place, rotate the lens clockwise .

GS Series 1075 User Manual 27 020-001225-03 Rev. 1 (02-2018)

Installation

Notice. Failure to comply with the following may result in property damage.

• Refer to the UST lens instruction sh eet for UST lens installation.

Installing the ceiling mount

Mount the projector with a Christie-approved mount, using the four mounting points on the underside of the projector.

See Optional accessories on page 83.

Warning! Failure to comply with the following could result in death or serious injury.

• The projector must be mounted securely according to the ceiling mount instructions.

• The warranty on this projector does not cover damage caused by the use of a non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.

1. Refer to the installation instructions and safety guidelines provided in the mount kit. See Optional accessories on page 83.

Installing the projector in the rigging frame

Install the projector in a Christie-approved rigging frame, using the four mounting points on the underside of the projector. See Optional accessories on page 83.

Warning! Failure to comply with the following could result in death or serious injury.

• The warranty on this projector does not cover damage caused by the use of a non-recommended rigging frame kit or installation of the ceiling mount kit in an improper location.

• The projector must be mounted securely according to rigging frame instructions.

GS Series 1075 User Manual 28 020-001225-03 Rev. 1 (02-2018)

1. Refer to the installation instructions and safety guidelines provided in the rigging frame kit. See Optional accessories on page 83.

Setup, alignment and test procedures

Follow the steps for the initial setup, alignment and test procedures.

1. Ensure all appropriate agencies have been notified.

Installation

2. Ensure that all required documentation is present at show site.

3. Hang appropriate laser area warning signage (if applicable).

4. Ensure all laser equipment is securely and rigidly mounted.

5. Ensure all cables are appropriately dressed and covered to prevent tripping or other hazards.

6. Perform visual inspection of projector for damage and other issues.

7. Notify and remove all non-essential personnel from fixed radiation area.

8. Check operation of safety features such as, shutters and labels.

9. Check all radiation areas for safe emission condition to ensure no people or objects are obstructing the beam path.

10. Power on lasers.

11. Open shutter and ensure proper operation of laser projector.

12. Use and fill-in Checklist for laser install.

13. Evaluate, discuss and address possible safety concerns.

14. Power off lasers.

15. Ensure operating procedures and checklists are current

GS Series 1075 User Manual 29 020-001225-03 Rev. 1 (02-2018)

Operation

Main Menu

1. Size & Position

2. Image Settings

3. Configuration

4. Light Source

5. Status

6. Input Switching & PIP

7. Language

8. Test Pattern

English

Off

The projector has multilingual on-screen display (OSD) menus so you can make image adjustments and change a variety of settings.

Most of the projector controls are accessed from within the projector menu system. Several groups of related functions are selectable from the Main menu as shown below.

1. To display the Main menu, on the IR remote keypad or on the built-in keypad on the rear of the projector, press MENU.

2. To navigate within the menu and adjust a setting up or down, use the arrow keys.

3. To select a highlighted menu item or use it to change or accept a value, press ENTER. You can then select the next item that you want to adjust in the menu.

4. To return to the previous menu or exit menus if at top level, press EXIT.

GS Series 1075 User Manual 30 020-001225-03 Rev. 1 (02-2018)

+ 72 hidden pages