Christie D4K2560 User Manual

D4K2560

User Manual

020-101076-04

D4K2560

User Manual

020-101076-04

NOTICES

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material. Canadian manufacturing facility is ISO 9001 and 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or Christie. In addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your product, the warranty does not cover:

a. Problems or damage occurring during shipment, in either direction. b. Projector lamps (See Christie’s separate lamp program policy). c. Problems or damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp other than a Christie

lamp supplied by Christie or an authorized distributor of Christie lamps.

d. Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras,

DVD players, etc., or use of a product with any non-Christie interface device.

e. Problems or damage caused by the use of any lamp, replacement part or component purchased or obtained from an

unauthorized distributor of Christie lamps, replacement parts or components including, without limitation, any distributor offering Christie lamps, replacement parts or components through the internet (confirmation of authorized distributors may be obtained from Christie).

f. Problems or damage caused by misuse, improper power source, accident, fire, flood, lightning, earthquake or other natural

disaster.

g. Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service

personnel or a Christie authorized repair service provider.

h. Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been

designed, modified or approved by Christie for such use.

i. Problems or damage caused by use of a projector in the presence of an oil-based fog machine or laser-based lighting that is

unrelated to the projector.

j. For LCD projectors, the warranty period specified in the warranty applies only where the LCD projector is in “normal use” which

means the LCD projector is not used more than 8 hours a day, 5 days a week.

k. Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such

product is protected from precipitation or other adverse weather or environmental conditions and the ambient temperature is

within the recommended ambient temperature set forth in the specifications for such product. l. Image retention on LCD flat panels. m.Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Please see the Maintenance section for specific maintenance items as they relate to your product. Failure to perform maintenance as required, and in accordance with the maintenance schedule specified by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s own expense.

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용 (A 급 ) 으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 , 가정 외의 지역에서 사용하는 것을 목적으로 합니다 .

Environmental

The product is designed and manufactured with high-quality materials and components that can be recycled and reused.

This symbol means

that electrical and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the environment we live in!

Addendum

Translated copies of this document are provided on the CD in the back of this document. The CD may also contain additional product documentation. Read all instructions before using or servicing this product.

本文档的翻译副本在本文档背面的 CD 上提供。该 CD 中还可能包含其他产品文档。使用或维修本产品之前请务必阅读所有说明。

文件背面的光碟提供了本文件的翻譯副本。這張光碟可能另外包含其他產品文件。請先閱讀所有指示再使用或送修本產品。

Le CD au dos de ce document contient des traductions de celui-ci dans différentes langues. Ce CD peut également contenir de la documentation supplémentaire sur le produit. Lisez toutes les instructions avant d'utiliser ou d'entretenir ce produit.

Übersetzte Versionen dieses Dokuments werden auf der CD auf dem Vorsatzblatt dieses Dokuments bereitgestellt. Die CD kann auch zusätzliche Produktdokumentation enthalten. Bitte lesen Sie diese Anweisungen vor der Verwendung dieses Produkts oder vor der Ausführung von Wartungsarbeiten am Produkt.

Le copie tradotte di questo documento sono fornite sul CD, sul retro di questo documento. Il CD potrebbe anche contenere altra documentazione sul prodotto. Si prega di leggere tutte le istruzioni prima di utilizzare questo prodotto o sottoporlo a manutenzione.

このドキュメントの翻訳版がこのドキュメントの裏面の CD で提供されています。CD には追加の製品マニュアルも収められています。この製品を使用したり、機能させたりする前に、すべての

指示をお読みください。

이 문서의 번역된 사본이 이 문서 후면의 CD 에서 제공됩니다 . 이 CD 에는 추가 제품 설명서가 포함되 어 있을 수 있습니다 . 이 제품을 사용하거나 수리하기 전에 모든 지침을 확인하십시오 .

Copias traduzidas deste documento são fornecida no CD contido na parte de trás deste documento. O CD pode conter documentação adicional do produto. Leia todas as instruções antes de usar ou prestar serviço com este produto.

Перевод данного документа представлен на компакт-диске на об Компакт-диск может также содержать дополнительную документацию по продукту. Перед использованием или обслуживанием продукта ознакомьтесь со всеми инструкциями.

Las copias traducidas de este documento se proporcionan en el CD que se encuentra en la parte trasera. En el CD también puede encontrar documentación adicional del producto. Lea todas las instrucciones antes de utilizar o realizar el mantenimiento de este producto.

Перекладені екземпляри цього документа містяться на компакт-диску, який додано до цього документа. На компакт-диску може також бути додаткова документація до виробу. Перш ніж

користуватися виробом або його обслуговува

ти, прочитайте всі інструкції.

оротной стороне документа.

Content

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Safety and warning guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Installation safety and warning guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

AC/power precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Lamp precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Product safety labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Projector overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Contact your dealer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

How the projector works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

List of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Installation and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Site requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Physical operating environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

External exhaust ducting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Tools required for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Projector components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Position the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Connect to AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Adjust the projector tilt and level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Install the foot extension rods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Install the touch panel controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Remove the projector shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Set up the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Portrait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Connect Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Input video mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Four-Port: 3GIC, TDPIC, THIC cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Four-Port: DDIC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Two-Port: TDPIC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Two-Port: DDIC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Connect a video source using DisplayPort . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

D4K2560 User Manual 9 020-101076-04 Rev. 1 (01-2015)

Content

Connect a video source using 3G Input card . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Connect a video source using HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Connect a video source using DVI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Select a video source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Connect a computer or server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Set up the ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Adjust the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Select screen image orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Maximize light output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Align the image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Adjust offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Adjust horizontal boresight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Adjust vertical boresight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Lock the lens offsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Adjust DMD convergence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Color correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Adjust color by temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Adjust color by precise chromaticity values . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Adjust color by saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Adjust the fold mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Projector LED status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Turn the projector on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

LED expected behavior on power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Turn the projector off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Work with lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Adjust lamp power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Adjust the lamp position with LampLOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Calibrate the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Manually adjust the lamp position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

View lamp information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Track lamp intensity with LiteLoc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Lamp details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Record new lamp information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Add lamp end-of-life indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Work with lenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Select a channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

D4K2560 User Manual 10 020-101076-04 Rev. 1 (01-2015)

Content

Enable warping and blending . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Send error notifications to specified devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Touch panel controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Tab structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Menu tab details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Status tab details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Backup, Restore, and Upgrade Projector Files . . . . . . . . . . . . . . . . . . . . . 54

Upgrade the projector software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Back up projector settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Export backup settings to an external device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Restore settings from a local backup profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Restore default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Import file from an external device to restore settings . . . . . . . . . . . . . . . . . . . . . . 55

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Maintenance shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Ventilation and cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Inspect and clean the airflow interlocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Inspect and clean the exhaust duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Inspect and clean the lamp blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Inspect and fill the coolant reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Remove the liquid cooling reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Filtration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Replace the light engine air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Replace the liquid cooling air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Replace the laminar airflow device filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Adjust the yoke assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Inspect and clean the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Remove dust from the projection lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Remove fingerprints, smudges, or oil from the projection lens . . . . . . . . . . . . . . 65

Remove the projection lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Install the projection lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Calibrate the lens motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Reset lens to home position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

D4K2560 User Manual 11 020-101076-04 Rev. 1 (01-2015)

Content

Projector does not power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Lamp does not ignite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Lamp suddenly turns off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Flicker, shadows or dimness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

LampLOC not working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Touch panel controller is blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Blank screen, no display of image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Cannot communicate with projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Inaccurate display colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Display is not rectangular . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Display has suddenly frozen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Display is jittery or unstable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Incoming signal(s) problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Touch panel controller or projector head problems on startup . . . . . . . . . . . . . . . . .70

The Projector LEDs or the MCPU board power LED are not on . . . . . . . . . . . . . . . 70

The MCPU board power LED is not on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

MCPU board power LED behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Touch panel controller does not connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Run the projector interrogator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Save TPC log files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

D4K2560 signal connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Optional Input cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Control signal compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Temperature sensor thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Warning thresholds for fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Warning threshold for liquid cooling module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Touch panel controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Regulatory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

D4K2560 User Manual 12 020-101076-04 Rev. 1 (01-2015)

Introduction

This manual is intended for professionally trained operators of Christie high-brightness projection systems. These operators are qualified to replace the lamp and air filters, but should not attempt to install or service the projector.

Only accredited Christie technicians who are knowledgeable about the hazards associated with high-voltage, ultraviolet exposure, and the high temperatures generated by the projector lamp are authorized to assemble, install, and service the projector.

For complete D4K2560 product documentation and technical support, go to

www.christiedigital.com.

Safety and warning guidelines

This projector must be operated in an environment that meets the operating range specification. Use only the attachments and/or accessories recommended by Christie. Use of others may result in the risk of fire, shock, or personal injury.

Warning! Failure to comply with the following could result in death or serious injury.

• Never look directly into the projector lens or at the lamp. The extremely high brightness can cause permanent eye damage. For protection from ultr aviolet r adiation, keep all projector housings intact during operation. Protective safety gear and safety goggles are recommended when servicing.

• FIRE HAZARD! Keep hands, clothes, and all combustible material away from the concentrated light beam of the lamp.

Caution! Failure to comply with the following could result in minor or moderate injury.

• Position all cables where they cannot contact hot surfaces or be pulled or tripped over.

• The American Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an 8-hour day to be less than 0.1 microwatts per square centimeters of effective UV radiation. A workplace evaluation is advised to assure emplo yees are not exposed to cumulative radiation levels exceeding the gover nment guidelines for your area. Be aware that some medications are known to increase sensitivity to UV radiation.

NOTE: During maintenance and cleaning operations, the instructions define that the unit must not be operational, thus the lamps are not active and there are no emissions. Optic a l a d justments are not considered maintenance. The lamps are tur ned on during optical adjustments and emissions are present.

D4K2560 User Manual 13 020-101076-04 Rev. 1 (01-2015)

Installation safety and warning guidelines

Danger! Failure to comply with the following results in death or serious injury.

• This product must be installed within a restricted access location which is normally inaccessible by the general public, including workers, visitors, and residents in the immediate vicinity, by means of engineering or administrative control measures but is accessible to authorized personnel that may not have specific safety training.

• This product must be located and positioned in a way as to restrict audience members from direct access to enter the light beam path.

• Do not install the projector overhead.

• When installing the projector in portrait mode, the device holding the projector must have a weight rating sufficient to hold the weight of the projector. The projector weighs 125kg (275 lbs).

• The projector uses a high-pressure lamp that may explode if improperly handled. Always wear manufacturer approved protective safety clothing (gloves, jacket, face shield) when the lamp door is open or when handling the lamp. Failure to comply results in death or serious injury.

Warning! Failure to comply with the following could result in death or serious injury.

• A qualified technician is required for all installations.

• SHOCK HAZARD. Never operate the projector without all of its covers in place.

• Use of the projector’s rear safety strap is mandatory to prevent the projector from tipping. Secure the strap between the projector and the surface it is mounted to.

• Four or more people are required to safely lift and hand-carry one projection head a short distance. Christie recommends removing the lamp before transporting the projector.

• Two or more people are required to safely lift and hand-carry the lamp power supply (LPS).

Introduction

Notice. Failure to comply with the following may result in property damage.

• Perform an automatic LampLOC adjustment when the lamp is moved, leveled, or a new lamp is installed in the projector.

• Keep the projector level when lifting or transporting. Avoid tilting the projector to the right. This can introduce an air bubble into the cool ant hoses that can result in an ai r lock and the ov erheating of the projector.

AC/power precautions

To correctly install this projector, a certified electrician must install a permanent three-phase connection to the lamp power supply (LPS). The LPS projector outlet is used to supply power to the projector head. Operate the projector at the recommended voltage.

Danger! Failure to comply with the following results in death or serious injury. Disconnect projector from AC before opening any enclosure.

Warning! Failure to comply with the following could result in death or serious injury.

• Verify that the projector is using a line cord, socket, and power plug that meets the appropriate local rating standards. Use only an AC power cord recommended by Christie. Do not attempt operation if the AC supply and cord are not within the specified voltage and power range.

• Do not allow anything to rest on the power cord. Locate the projector where the cord cannot be abused by persons walking on it or objects rolling over it. Never operate the projector if the power cable appears damaged in any way.

• Do not overload power outlets and extension cords as this can result in fire or shock hazards.

D4K2560 User Manual 14 020-101076-04 Rev. 1 (01-2015)

Introduction

Lamp precautions

Lamps used in the projector are under high pressure and must be handled with caution. Lamps can explode and cause serious personal injury if dropped or mishandled.

Danger! Failure to comply with the following results in death or serious injury.

• Never attempt to access the lamp compartment while the lamp is on. Wait at least 10 minutes after the lamp turns off before powering down, disconnecting from AC, and opening the lamp door.

• The arc lamp operates at a high pressure that increases with temperature. Failure to allow the lamp to sufficiently cool before handling, increases the potential for an explosion causing personal injury or property damage.

• Always wear manufacturer approved protective safety clothing (gloves, jacket, face shield) when the lamp door is open or when handling the lamp. Only qualified technicians should install projector lamps.

Warning! Failure to comply with the following could result in death or serious injury.

• Possibly hazardous optical radiation emitted from this product. (Risk group 3)

• Thermal radiation emitted from this product may cause burns. (Risk group 3)

Recommended protective clothing includes, but may not be limited to a polycarbonate face shield, protective gloves, and a quilted ballistic nylon jacket or a welder’s jacket. This equipment is included in included in the Christie Protective Clothing Safety kit P/N: 598900-095.

Christie’s protective clothing recommendations are subject to change. Any local or federal specifications take precedence over Christie recommendations.

D4K2560 User Manual 15 020-101076-04 Rev. 1 (01-2015)

Product safety labels

Indicates the presence of a grounding point.

Indicates the presence of an earth grounding point.

Indicates the presence of a dangerous condition or situation.

Indicates the presence of a pinch hazard. T o av oid personal injury, keep hands clear and loose clothing tied back.

Indicates the presence of a hot surface. To avoid personal injury, always allow the projector to cool down for a minimum of 10 minutes before performing maintenance or service procedures.

Introduction

Indicates the presence of a hot surface. To avoid personal injury, always allow the projector to cool down for a minimum of 10 minutes before performing maintenance or service procedures.

Indicates the presence of an electrical shock hazard. To avoid personal injury, always disconnect all power sources before performing maintenance or service procedures.

Indicates the presence of an electrocution hazard. T o avoid personal injury, always disconnect all power sources before performing maintenance or service procedures.

Indicates the presence of moving fan blades. To avoid personal injury, keep hands clear and loose clothing tied back. Always disconnect all power sources before performing maintenance or service procedures.

Indicates exposure to bright light. To avoid personal injury, never look directly at the light source.

Indicates the presence of an explosion hazard. To avoid personal injury, always disconnect all power sources and wear Christie approved protective clothing.

Indicates the presence of a fire hazard. To avoid personal injury and property damage, always adhere to the instructions described in this manual.

D4K2560 User Manual 16 020-101076-04 Rev. 1 (01-2015)

Introduction

Always disconnect all power sources before performing maintenance or service procedures.

See the product user manual for specific information and directions.

See the product service manual for specific information and directions.

Never look directly into the projector lens . The extremel y high bright ness can cause permanent eye damage.

This label warns of a cross-connection hazard when installing multiple projectors at once. A fire hazard exists if a lamp power supply interlock cable is connected to a different projector than its lamp power cables.

For more information, see Adjust the projector tilt

and level in the Installation and Setup chapter

Projector overview

The D4K2560 is a professional quality, easy-to-use, split-body projector using Digital Light Processing (DLP™) technology from Texas Instruments. Integrating smoothly into traditional projection environments; the D4K2560 interfaces with local networks throughout the world, for multimedia presentations from a variety of formats, to offer stunning wide screen, high-resolution 4K images at 60 frames per second.

Contact your dealer

If you encounter a problem with your Christie projector, contact your dealer. To assist with the servicing of your projector, enter the information in the tables below and keep this information with your records.

Purchase Record

Dealer: Dealer or Christie Sales/Service contact phone number:

D4K2560 User Manual 17 020-101076-04 Rev. 1 (01-2015)

Purchase Record

Projector serial number: Purchase date: Installation date:

*The serial number can be found on the license label located on the front panel

Ethernet Settings

Default gateway Projector IP address Subnet mask

Key features

• 3-chip 4K DLP™ light engine

• 4096 x 2160 native pixel format

Introduction

• 2.0 and 3.0 kW Xenon lamps available

• Warp and blend of projected images

• Supports screens up to approximately 100 feet in width

• T ouch panel controller (TPC) for main projector interface. V erify you have the latest software by visiting http://www.christiedigital.com

• 1x 10/100BaseT Ethernet port

• RS232 ports for communication

• 4x Option slots accepting a variety of digital video input option cards

• LiteLOC™ feature for constant image brightness

• LampLOC™ feature for motorized three-axis lamp alignment

• Electronically operated “quick” douser

• Motorized lens mount

• LED indicators on the rear corners of the projector for easy-to-read status indication

• Replaceable air filters (no tools required)

• Optional rack mount stand

• Choice of field-interchangeable zoom lenses

Model Name Part Number

D4K2560 129-009100-XX

D4K2560 User Manual 18 020-101076-04 Rev. 1 (01-2015)

Introduction

How the projector works

The D4K2560 accepts a variety of input signals for projection on front or rear projection screens, typical in commercial or other large screen applications. High-brightness light is generated by a short arc Xenon lamp, then modulated by three Digital Micromirror Device (DMD) panels responding to incoming data streams of digitized red, green and blue color information. As these digital streams flow from the source, light from the responding “on” pixels of each panel is reflected, converged and then projected to the screen through one or more projection lenses, where all pixel reflections are superimposed in sharp full-color images.

List of components

Verify the following components were received with the projector:

• Touch panel controller (TPC)

• Lens plug (required for shipping when lens is not installed to prevent contamination of critical optical components)

• Light engine removal tool

• Convergence tool

• Nylon safety strap with clip (required to secure projector to tabletop or optional rack mount)

•Warranty card

•Shroud

• Access keys

• Web registration form

D4K2560 User Manual 19 020-101076-04 Rev. 1 (01-2015)

Installation and Setup

This section explains how to install, connect, and optimize the projector display.

Site requirements

To safely install and operate the projector, the installation location must have restricted access for authorized personal only and meet these minimum requirements.

Physical operating environment

• Maximum Ambient Temperature (operating) 35°C (95°F)

• Minimum Ambient Temperature (operating) 10°C (50°F)

External exhaust ducting

The installation site must provide a minimum of 450 CFM (ft 3/min) external exhaust airflow to ensure adequate cooling of the Xenon arc lamp at less than or equal to 25°C (77°F) ambient and less than 3,000 ft (914.4 m) elevation. Above 25°C or 3,000 ft, 600 CFM i s required.

For more details, see Connect external exhaust ducting on page 27.

Power connection

The requirements listed below are applicable for permanently wired installation or power cord connection:

• Terminal block, electrician hard-wired to the projector head.

• Electrical rating: 200 - 240 VAC, 23 A max.

• This product can be connected to an IT power distribution system.

Tools required for installation

• 12” screwdrivers: Phillips #2 (magnetic) and flat

• 19mm and 7/8” wrenches

• Assorted Allen keys (metric)

D4K2560 User Manual 20 020-101076-04 Rev. 1 (01-2015)

• Christie approved protective safety clothing if working with the lamp

• Lens cleaning tissue and solution

Installation and Setup

D4K2560 User Manual 21 020-101076-04 Rev. 1 (01-2015)

Projector components

LAMP SIDE

LENS SIDE

Installation and Setup

ID Item Description

A Touch panel controller (TPC) A touch-sensitive screen used to control and monitor operation. For

B LED status indicators LED color and blinking rates (located in both back corners of the projector)

C Manual douser override Closing the douser rotates a shutter blade in front of the lamp and reduces

D Lamp door and lamps The lamp door provides access to the lamp compartment and must remain

E Exhaust duct and vane switch Extracts heated air from the l amp c ompartme nt. The vane switch mounted

F Liquid cooling air filter Ccver

and air filter

G Shroud (two-piece) Covers the motorized lens mount assembly.

information about TPC controls and settings, see Menus on page 50.

provide information about the status of the projector. For information about projector states and status, see LED expected behavior on power up on

page 45.

the lamp power to 2.0 kW to conserve lamp life. The override is for emergency use only.

closed and locked for normal operation. Lamp replacement should only be performed by qualified technicians. For a complete list of available lamp types, see Accessories on page 80.

inside the rigid port monitors airflow. See Site requirements on page 20. Filters air before it circulates to cool the heat exchanger. For replacement

instructions, see Maintenance shutdown on page 57.

H Projection lens A variety of lenses can be used with the D4K2560Mirage 4K25. For a list of

I Air filter cover and air filter Filters the intake air before it circulates through the front compartment to

available lenses, see on page 82

cool the main electronics. For replacement instructions, see Maintenance

shutdown on page 57.

D4K2560 User Manual 22 020-101076-04 Rev. 1 (01-2015)

ID Item Description

Installation and Setup

J Input panel faceplate Provides a variety of ports for connecting external devices. F or information

about connecting devices and inputs, see Connect Devices on page 31.

Position the projector

Keep the projector lens as perpendicular to the screen as possible, even if significantly above the screen center. When a particularly short throw distance combines with a wide screen, you may have to forfeit some aim and stay more perpendicular to the screen. In such cases, some lens offset can reduce the keystone distortion.

1. Position the projector at an appropriate throw distance (projector-to-screen distance) and vertical position. Ideally , center the projector with the screen. If space is limited, aim the projector slightly off-center. This increases side keystoning, but reduces the horizontal lens offset required.

90°

≠90°



2. If using an optional rack stand (P/N: 108-282101-02), assemble the rack stand using the instructions provided with the rack stand. Use the hold down clamp (P/N: 116-100101-01) when securing the projector to the rack stand.



D4K2560 User Manual 23 020-101076-04 Rev. 1 (01-2015)

Connect to AC power

Failure to comply with the following could result in death or serious injury.

• Certified electrician required during installation. Ground (earth) connection is necessary for safety. Never compromise safety by returning the current through the ground. Connect ground FIRST to reduce shock hazard.

• Use an appropriate strain relief connector on the AC supply cable to prevent the cable from rubbing against the LPS knockout plate and becoming damaged.

When connecting the projector directly to AC power, follow all electrical codes for your location. In addition, follow these recommendations:

• Use 10AWG or 8AWG wiring. The distance between the wall circuit breaker and the projector must not exceed 20 meters using 10A WG cables or 30 meters using 8AWG cables.

• For North American installations, us e at least 10A WG copper wires for the connection of the main AC supply to the projector’s ground lug.

• Copper or aluminum are acceptable as conductor wiring material to the terminal block.

When connecting the projector to AC power with a pluggable type-B cable, follow all electrical codes for your location. In addition, follow these recommendations:

• There must be easy access to the current protection device or breaker in the building.

• Use minimum 10AWG wiring, with a maximum length of 4.5 m for U.S and Canada. For international installations the length should be based on the local electrical codes.

• The socket-outlet is installed near the equipment and is easily accessible.

• The plug can be used as the device disconnect and is near the unit and easily accessible. The circuit breaker on the projector baseplate (located under the front lens-side corner) can also be used as a means of disconnect.

Installation and Setup

1. On the bottom of the projector in the front lamp-side corner, loosen the two screws and slide the access panel to expose the terminal block.

2. Remove four screws securing the knockout plate to the bottom right corner of the front bezel. Remove the knockout plate. The AC supply is routed to the terminal block through an appropriate strain relief mounted on this knockout plate.

D4K2560 User Manual 24 020-101076-04 Rev. 1 (01-2015)

Installation and Setup

3. Connect to the terminal block.

The terminal block accommodates up to an eight AWG wire. If required, use a 90° strain relief connector to route the power cable in a downward direction.

Always connect the ground lead first to reduce shock hazard.

• If connecting to permanent power, connect the AC power source to the terminal block, beginning with the ground lead.

• If connecting to a pluggable type-B cable, connect the cable to the terminal block, beginning with the ground lead.

• Use an appropriately sized strain relief connector with the knockout plate provided to ensure adequate environmental sealing and to prevent the cables from wear and accidentally being torn out.

4. Reinstall the knockout plate and secure it with four screws.

5. Reinstall the bottom access panel over the terminal block and secure it with two screws.

If using a pluggable type-B cable, connect to the building’s AC power source.

D4K2560 User Manual 25 020-101076-04 Rev. 1 (01-2015)

Installation and Setup

19 mm

Adjust the projector tilt and level

Warning! Failure to comply with the following could result in death or serious injury.

• The projector’s rear safety strap must be in place before adjusting the projector feet.

• Do not over-extend the feet. Make sure several threads are engaged into the projector’s baseplate to secure the projector from falling.

Adjust the projector tilt to fill the maximum amount of screen while minimizing keystone. Lens offset can be used to center the image in the center of the screen..

Notice. Failure to comply with the following may result in property damage. The front-to-back tilt of the projector must not exceed 15 degrees.

1. Secure a safety lifting strap rated to handle the projector weight at the rear of the projector.

2. Hoist up the projector.

3. To adjust the vertical or horizontal position of the projector, extend or retract the adjustable feet on the bottom of the projector (A).

4. Once the required adjustment is made, tighten the lock nut against the bottom of the projector (B).

The projector provides 4 inches of adjustment at the front and 11.5 inches of adjustment at the rear.

5. If the vertical or horizontal position of the projector requires more adjustment than the standard feet allow, two 6-inch extension rods can be installed to increase the amount of available adjustment.

Install the foot extension rods

1. Elevate the rear of the projector to access the two rear feet.

2. Remove the feet by loosening the lock nut and rotating the each foot out of the projector.

3. Add the extension rods to the standard feet.

4. Thread the extended feet into the projector’s baseplate.

5. Adjust the feet until the required tilt is achieved.

6. Lock the feet in place by turning each lock nut until it fits tight against the projector.

D4K2560 User Manual 26 020-101076-04 Rev. 1 (01-2015)

+ 58 hidden pages