Christie D12HD-H operation manual

User Manual

020-000807-02

H Series, HS Series, GS Series

(700, 850)

Warping and Blending

NOTICES

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material. Canadian manufacturing facility is ISO 9001 and 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or Christie. In addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your product, the warranty does not cover:

Problems or damage occurring during shipment, in either direction.

Projector lamps (See Christie’s separate lamp program policy).

Problems or damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp other than a Christie lamp supplied by

Christie or an authorized distributor of Christie lamps.

Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras, DVD players, etc., or use

of a product with any non-Christie interface device.

Problems or damage caused by the use of any lamp, replacement part or component purchased or obtained from an unauthorized distributor of Christie

lamps, replacement parts or components including, without limitation, any distributor offering Christie lamps, replacement parts or components through the internet (confirmation of authorized distributors may be obtained from Christie).

Problems or damage caused by misuse, improper power source, accident, fire, flood, lightening, earthquake or other natural disaster.

Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service personnel or a Christie

authorized repair service provider.

Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been designed, modified or

approved by Christie for such use.

Problems or damage caused by use of a projector in the presence of an oil-based fog machine or laser-based lighting that is unrelated to the projector.

For LCD projectors, the warranty period specified in the warranty applies only where the LCD projector is in “normal use” which means the LCD projector

is not used more than 8 hours a day, 5 days a week.

Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such product is protected from

precipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended ambient temperature set forth in the specifications for such product.

Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Please see the Maintenance section for specific maintenance items as they relate to your product. Failure to perform maintenance as required, and in accordance with the maintenance schedule specified by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user’s own expense.

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

ENVIRONMENTAL

The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the environment we live in!

-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according

Content

Warping and blending..........................................4

Operating a single projector........................................4

Channel Network indicators......................................4

Deleting a selected channel......................................5

Changing General settings.......................................5

Enabling warping.............................................. 5

Adjusting cursors............................................ 6

Enabling edge blending...........................................6

Enabling test patterns........................................... 7

Example edge blends using a test pattern.............................8

Enabling black leveling...........................................9

Operating multiple projectors.......................................9

Configuring blending settings for multiple projectors......................10

Saving current settings..........................................11

Opening previously saved settings...................................11

Applying previously saved settings...................................11

ev. 1 (07-2016)

Warping and blending

The projector provides three major functions: warp, edge blending, and black leveling.

Operating a single projector

Use the New Multi-Function feature to operate a single projector.

To enable New Multi-Function, from the File menu, select New Multi-Function.

The Projector Control dialog appears.

Channel Network indicators

The Channel Network icons pro

Icon Description

Indicates disconnection from the channel network.

Indicates connection to the channel network. The selected channel appears in a blue box.

ev. 1 (07-2016)

vide information about the connection to the Channel Network.

+ 8 hidden pages