Christie CC2 Installation And User Manual
CC2 Electric Barbecue Cooktop
Installation and User Manual
dachristie.com
+61 3 9708 2999
Part numbers 1005; 1006
Installation Manual 6838_03
This user manual is an integral part of the appliance
and must therefore be kept in its entirety and in
an accessible place. Read this user manual
carefully before using the appliance.
CC2 Electric Barbecue Cooktop (Part numbers 1005; 1006)
2 | Table of contents
1 GENERAL INFORMATION 3
1.1 Product diagram | Figure 1, 2 4
1.2 Safety instructions 5
1.3 How to read this manual 6
1.4 Manufacturer liability 6
1.5 Conditions of use 7
1.6 Declaration of conformity 7
1.7 Specifications | Table 1, 1.7.1 Circuit Diagram 8
1.8 Description 9
1.9 Disposal 9
1.10 Boxed contents | Figure 3 10
2 INSTALLATION 11
2.1 Design guidelines for installing a CC2 cooktop | Figure 4, 5, 6 12
2.2 Instructions for installing a CC2 cooktop | Figure 7, 8, 9 15
2.3 Installation requirements 18
3 OPERATION 19
Figure 10 20
4 CLEANING AND MAINTENANCE 21
4.1 Safety considerations 22
4.2 Environmental considerations 22
4.3 Cleaning the cooktop 22
4.4 Cleaning the waste container | Figure 11 23
4.5 General cleaning and maintenance 25
5 FREQUENTLY ASKED QUESTIONS 26
6 TROUBLE SHOOTING 29
6.1 Diagnostic codes | Table 2 30
7 OPTIONS AND ACCESSORIES 31
8 WARRANTY AND CUSTOMER CARE 33
Installation Manual 6838_03
3General information |
GENERAL
INFORMATION
1.
CC2 Electric Barbecue Cooktop (Part numbers 1005; 1006)
4
FIG 1
1.1 Product diagram
| General information
148 mm
to fat drain tube
Front view
M8 x 100 mm long mount bolts
2 places
160 mm projection
below benchtop
216 mm
56 mm projection
above benchtop
Start/Stop button
with LED indicator
490 mm minimum benchtop cutout width
459 mm bolt hold down point centres
47 mm
Top view
435 mm
cooking area
536 mm
600 mm
435 mm
cooking area
536 mm
600 mm
FIG 2
Installation Manual 6838_03
5
1.2 Safety instructions
General information |
Risk of personal injury
• Any variation from the original Product
Specification, including the use of
different components, may result in injury
and will void the Safety Certification and
Product Warranty
• This appliance must only be installed
and serviced by an authorised person
(e.g. a licensed electrician) who will
be directly responsible for installing
it according to the manufacturer’s
installation instructions, AS/NZS3000,
and all relevant building and electrical
regulations. For all other countries
the local applicable regulations and
procedures must be followed
• The product is to be connected to
fixed wiring. Isolation switch must
be incorporated in the fixed wiring in
accordance with the national wiring
rules. Isolation switch shall be directly
connected to the supply leads and shall
have a contact separation in all poles
providing full disconnection under
overvoltage category III conditions
• Ensure the appliance is correctly earthed
• Isolate the appliance from the mains
electricity supply before doing any work
• The appliance and its accessible parts
become very hot while in use. Never
touch the hotplate or components
while it is switched on
• The appliance must be fixed into an
enclosed structure to prevent access to
its underside
• Where the underside is not fully
enclosed, a Christie Open Bench
Installation Kit must be used
• This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved. Children shall not play with
the appliance. Cleaning and user
maintenance shall not be made by
children without supervision
• Children under eight years of age must
be kept at a safe distance if they are
not being constantly supervised
• Never leave the appliance unattended
during cooking operations
• Never try to put out an appliance fire
with water. Turn off the appliance and
smother the flames with a fire blanket
or similar material
• If the power supply cable is damaged,
contact Christie technical support or
your local contractor immediately for a
replacement
• The unit must be installed, operated,
and maintained in accordance with
the Manufacturer’s Instructions
• It is recommended that two people lift
this appliance
CC2 Electric Barbecue Cooktop (Part numbers 1005; 1006)
6
1.2 Safety instructions
1.3 How to read this manual
Risk of damage to the Appliance
• Only non-toxic, pH neutral cleaning products with a pH between 6 and 9 must
be used
• Corrosive (acidic or alkaline) cleaning products may leave a toxic residue on the
cooking surface, damage the electronic circuitry, components, or facia labels, and void
Product Warranty
• Pressure washers must not be directed into openings in the appliance
• Charcoal or similar combustible fuels must not be used with this appliance
• Only use products intended specifically for cleaning stainless steel. Products intended
for cleaning mild steel must not be used on this appliance
Chapter headings and sub heading are
listed in the Table of Contents along
with the relevant page numbers
Key words:
• “Must” and “must not” are
mandatory instructions
• “Should’ and “should not” are
advisory instructions
The following icons are used throughout
the manual
Electrical Hazard icon
warns of possible
electrical shock
Warnings or Caution
icon warns how to
prevent personal injury
Hot Surface icon warns
not to touch hot surfaces
1.4 Manufacturer liability
The manufacturer declines all liability for damage to persons or property caused by:
• Use of non-original spare parts
• Use of the appliance other than as intended
• Tampering with any part of the appliance
• Non-observance of instructions contained in this Installation and User Manual
| General information
Installation Manual 6838_03
7
This appliance has been tested and certified to Australian Standards (RCM) and European
standards (CE) declaration of conformity certificate available on request. The Product
Identification Label contains the following information:
• Type and model
• Electrical ratings
• RCM and CE compliance marks
• Manufacturers name and contact details
DO NOT REMOVE THIS PRODUCT IDENTIFICATION LABEL. IF IT IS ILLEGIBLE OR
DAMAGED, CONTACT CHRISTIE.
Safety features incorporated into this product include a time delay (6 seconds) start button
located on the cooktop, and an over temperature normally closed thermostat (twin pole), with
a manual reset button that will independently shut off power to the relay in case of overheating.
1.5 Conditions of use
1.6 Declaration of conformity
• The appliance must be connected to a
residual current device (RCD) which has
a rated residual operating current not
exceeding 30mA
• A 240V, 15A weather proof general
power outlet (GPO) must be supplied
and located within the structure housing
the appliance
• No part of the appliance, including the
15A plug, may be modified without
written authorisation from the manufacturer
• All repairs under Warranty must first be
approved by Christie. No responsibility
will be accepted for repairs made
without authorisation
• This Installation and User Manual
is an integral part of the appliance
and must be kept in its entirety and
in an accessible place for the whole
working life of the appliance. Read this
Installation and User Manual carefully
before using the appliance
• This appliance is suitable for indoor and
outdoor use
• The safety instructions in chapter 1.2
form part of the conditions of use for
this appliance
General information |
CC2 Electric Barbecue Cooktop (Part numbers 1005; 1006)
8
POWER SUPPLY
LRS-35-12
240VAC
POWER INLET
A
N
GND
BROWN
BLUE
YELLOW GREEN
OVER TEMP
THERMOSTAT
L N GND -V +V
BBQ
CONTROLLER
+V
-V
BROWN
WHITE
YELLOW
GREEN
ON / OFF SWITCH
PUSH BUTTON
12VDC 200mA
BROWN
BLACK
BLACK
BLACK
RED
BLACK
BROWN
GRAYBLACK
HEAT SENSOR
GREEN LED
12VDC 20mA
RED LED
12VDC 20mA
HEATING ELEMENT
CONTROLLER
ENCLOSURE
RELAY
Rated voltage 230-240V AC
Frequency 50Hz
Rate current 15A
Element 3.5KW
Nominal target temp 255 degrees
Nominal cook time 20 min
Nominal tare weight 20kg
Nominal packed weight 25kg
Requires RCD 30mA
Requires 20 A circuit breaker
Plan view Above
bench
Below
bench
Hotplate Cooking area
Dimensions
in mm
600 x 600 56 160 536 x 536 435 x 435
1.7 Specifications
| General information
1.7.1 CIRCUIT DIAGRAM
TABLE 1
Installation Manual 6838_03
9
1.8 Description
1.9 Disposal
General information |
• The Christie CC2 Electric Barbecue Cooktop is a self-contained hotplate-style
barbecue with fully automatic functions, designed for unmonitored use by the public
• The CC2 is supplied fully assembled and tested, requiring no further assembly or
rigging. It is designed to be dropped into place
• The CC2 is provided with 15A rated moulded plug on a 1-meter long supply cord. For
countries outside of Australia and New Zealand, CC2 is provided with a 1.8 m power
supply cord only. An appropriate 15A rated and approved plug must be attached by a
suitably qualified person
• This appliance must be disposed of separately from other waste (Directives 2002/95/
EC, 2002/ 96/EC, 2003/108/EC)
• The appliance does not contain substances in quantities sufficient to be considered
hazardous to health and the environment in accordance with current European directives
• To dispose of the appliance: Cut the power supply cable and remove it along with the
plug. Deliver the appliance to an appropriate recycling facility for electrical and electronic
equipment waste
• Christie appliances are packaged in non-polluting and recyclable materials. Deliver the
packing materials to the appropriate recycling facility
CC2 Electric Barbecue Cooktop (Part numbers 1005; 1006)
10
1.10 Boxed contents
| General information
CC2 Cooktop Anti-rotation brackets
Installation & User Manual
Installation & User Manual
The following contents are supplied with a Christie CC2 electric barbecue cooktop:
• CC2 Electric Appliance
• Preassembled 240v, 15A power supply cord with three pin plug
• For countries outside of Australia and New Zealand, the CC2 is provided with a 1.8 m
power supply cord only
• 2 x Anti rotation brackets
(attached to hold down bracket, remove prior to installation)
• 2 x 8 mm bolts with washers and nuts
• 2 x 8 mm wing nuts and washers
• This Installation and User Manual
FIG. 3
Installation Manual 6838_03
11Installation |
INSTALLATION
2.
Loading...