The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 8
Global LCD Panel Exchange Center
26 NC For LCD internal use only, Do not connect
27 NC For LCD internal use only, Do not connect
28 Vcc +5.0V power supply
29 Vcc +5.0V power supply
30 Vcc +5.0V power supply
Note (1) Connector Part No.:
WF13-422-3033(Fullconn) or 187098-30091(Ptwo) or GS23302-0311R-7H(Foxconn)
Note (2) User’s connector Part No:
Mating Wire Cable Connector Part No.: FI-X30H(JAE) or FI-X30HL(JAE)
Mating FFC Cable Connector Part No.: 217007-013001 (P-TWO) or JF05X030-1 (JAE).
Note (3) The first pixel is odd.
Note (4) Input signal of even and odd clock should be the same timing.
www.panelook.com
PRODUCT SPECIFICATION
1,1
(odd)
2,1
3,1
1,2
(even)
2,2
1,3
(odd)
1,4
(even)
1,Xmax
Pitch
Pitch
Ymax,1
Version 3.1 9 September 2011 8 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Ymax,
Xmax
www.panelook.com
Page 9
Global LCD Panel Exchange Center
4.3 ELECTRICAL CHARACTERISTICS
4.3.1 LCD ELETRONICS SPECIFICATION
Parameter Symbol
Power Supply Voltage Vcc 4.5 5.0 5.5 V -
Ripple Voltage VRP -- -- 300 mV -
Rush Current I
AC off Rush Current Ioff_
Power Supply Current
Vertical Stripe
Power Consumption PLCD - 6.0 7.7 Watt (4)
LVDS differential input voltage Vid 100 - 600 mV
LVDS common input voltage Vic 0.05 -- 2.85 V
Note (1) The ambient temperature is Ta = 25 ± 2 ºC.
www.panelook.com
PRODUCT SPECIFICATION
Value
Min. Typ. Max.
-- -- 3 A (2)
RUSH
- -- 4 A (5)
RUSH
White -- 0.42 0.47 A (3)a
Black -- 1.2 1.4 A (3)b
-
-
-
-- 0.69 0.71 A (3)c
Unit Note
Note (2) Measurement Conditions:
Version 3.1 9 September 2011 9 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 10
Global LCD Panel Exchange Center
Note (3) The specified power supply current is under the conditions at Vcc = 5.0 V, Ta = 25 ± 2 ºC, Fr = 60Hz,
whereas a power dissipation check pattern below is displayed.
www.panelook.com
PRODUCT SPECIFICATION
Note (4) The power consumption is specified at the pattern with the maximum current.
Note (5) The Rush current would be happened when system doesn’t follow Power sequence in AC off status
Note (6) VID waveform condition
Version 3.1 9 September 2011 10 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 11
Global LCD Panel Exchange Center
4.3.2 Vcc Power Dip Condition
www.panelook.com
PRODUCT SPECIFICATION
4.3.3 BACKLIGHT UNIT
Parameter Symbol
LED Light Bar Input
Voltage Per Input Pin
LED Light Bar Current
Per Input Pin
LED Life Time LLED 40000 -- -- Hrs (3)
Power Consumption PBL -- 8.87 10.32 W
Note (1) LED light bar input voltage and current are measured by utilizing a true RMS multimeter as shown
below:
Note (2) PBL = IPIN × VPIN × ( 4 ) input pins ,
Note (3) The lifetime of LED is defined as the time when LED packages continue to operate under the
conditions at Ta = 25 ±2 к and I= (65)mA (per chip) until the brightness becomes Љ 50% of its
original value.
VPIN -- 34.1 37.4 V
IPIN -- 65 69 mA
Min. Typ. Max.
Value
Unit Note
(1),
Duty=100%,
IPIN=(65mA)
(1), (2)
Duty=100%
(1)
Duty=100%,
IPIN=(65mA)
Version 3.1 9 September 2011 11 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 12
Global LCD Panel Exchange Center
4.3.4 LIGHTBAR Connector Pin Assignment
(1).Connector: CI1406M1HRF-NH(CviLux) or compatible.
(2) LB Connector drawing:
www.panelook.com
PRODUCT SPECIFICATION
CN1
Pin number Description
1 Cathode of LED string
2 Cathode of LED string
3 VLED
4 VLED
5 Cathode of LED string
6 Cathode of LED string
Note (1) User’s Mating Connector Part No.: CI1406SL000-NH (CviLux) or Compatible.
˟˼˺˻˵˴
˕˴˶˾ʳ˦˼˷˸ʳ˹ʳˠ˷˿˸
˕˴˶˾ʳ˦˼˷˸ʳ˹ʳˠ˷˿˸
˕˴˶˾ʳ˦˼˷˸ʳ˹ʳˠ˷˿˸˕˴˶˾ʳ˦˼˷˸ʳ˹ʳˠ˷˿˸
ˣ˼˄
ˣ˼˄
ˣ˼˄ˣ˼˄
Version 3.1 9 September 2011 12 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 13
Global LCD Panel Exchange Center
4.4 LVDS INPUT SIGNAL SPECIFICATIONS
4.4.1 LVDS DATA MAPPING TABLE
LVDS Channel O0
LVDS Channel O1
LVDS Channel O2
LVDS Channel O3
LVDS Channel E0
LVDS Channel E1
LVDS Channel E2
LVDS Channel E3
LVDS output D7 D6 D4 D3 D2 D1 D0
Data order OG0 OR5 OR4 OR3 OR2 OR1 OR0
LVDS output D18 D15 D14 D13 D12 D9 D8
Data order OB1 OB0 OG5 OG4 OG3 OG2 OG1
LVDS output D26 D25 D24 D22 D21 D20 D19
Data order DE NA NA OB5 OB4 OB3 OB2
LVDS output D23 D17 D16 D11 D10 D5 D27
Data order NA OB7 OB6 OG7 OG6 OR7 OR6
LVDS output D7 D6 D4 D3 D2 D1 D0
Data order EG0 ER5 ER4 ER3 ER2 ER1 ER0
LVDS output D18 D15 D14 D13 D12 D9 D8
Data order EB1 EB0 EG5 EG4 EG3 EG2 EG1
LVDS output D26 D25 D24 D22 D21 D20 D19
Data order DE NA NA EB5 EB4 EB3 EB2
LVDS output D23 D17 D16 D11 D10 D5 D27
Data order NA EB7 EB6 EG7 EG6 ER7 ER6
www.panelook.com
PRODUCT SPECIFICATION
Version 3.1 9 September 2011 13 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 14
Global LCD Panel Exchange Center
4.4.2 COLOR DATA INPUT ASSIGNMENT
The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the
color. The higher the binary input, the brighter the color. The table below provides the assignment of color
versus data input.
Color
R7 R6 R5 R4 R3 R2 R1 R0
Black
Red
Green
Basic
Colors
Gray
Scale
Of
Red
Gray
Scale
Of
Green
Gray
Scale
Of
Blue
Note (1) 0: Low Level Voltage, 1: High Level Voltage
Blue
Cyan
Magenta
Yellow
White
Red(0) / Dark
Red(1)
Red(2)
:
:
Red(253)
Red(254)
Red(255)
Green(0) / Dark
Green(1)
Green(2)
:
:
Green(253)
Green(254)
Green(255)
Blue(0) / Dark
Blue(1)
Blue(2)
:
:
Blue(253)
Blue(254)
Blue(255)
0
1
0
0
0
1
1
1
0
0
0
:
:
1
1
1
0
0
0
:
:
0
0
0
0
0
0
:
:
0
0
0
0
1
0
0
0
1
1
1
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
www.panelook.com
PRODUCT SPECIFICATION
Data Signal
Red Green Blue
G7 G6 G5 G
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
:
0
1
1
0
0
0
:
:
:
:
0
0
0
0
0
0
:
:
:
:
0
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
:
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
1
1
1
1
1
1
0
0
0
0
0
0
:
:
:
:
:
:
0
0
0
0
0
0
G3 G2 G1 G0
4
0
0
0
0
0
0
1
1
1
0
0
0
1
1
1
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
:
:
:
:
0
0
0
0
0
0
:
:
1
1
1
0
0
0
:
:
0
0
0
:0
0
0
0
0
0
:
:
1
1
1
0
0
0
:
:
0
0
0
:
0
0
0
0
0
0
:
:
1
1
1
0
0
0
:
:
0
0
0
0
0
1
0
1
0
1
1
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
1
0
1
0
1
1
0
0
0
:
:
:
:
0
0
0
0
0
1
:
:
:
:
0
1
1
0
0
0
:
:
:
:
0
0
0
B
B6 B5 B4 B3 B2
7
0
0
0
0
0
0
1
0
0
0
1
1
1
1
1
0
1
1
1
0
0
1
1
1
0
0
0
0
0
0
0
0
0
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
:
:
:
:
:
:
1
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
0
1
1
0
1
1
0
1
1
0
0
0
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
B1 B
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
:0
0
0
0
0
0
:
:
:
:
0
0
0
0
1
0
:
:
:
:
1
0
1
Version 3.1 9 September 2011 14 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 15
Global LCD Panel Exchange Center
4.5 DISPLAY TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
LVDS Clock
Vertical Display Term
Horizontal Display Term
Note: Because this module is operated by DE only mode, Hsync and Vsync input signals are ignored.
www.panelook.com
PRODUCT SPECIFICATION
Frequency Fc 58.54 74.25 97.98 MHz -
Period Tc - 13.47 - ns
Input cycle to
cycle jitter
Input Clock
to data skew
Spread
spectrum
modulation
range
Spread
spectrum
modulation
frequency
Frame Rate Fr 50 60 75 Hz -
Total Tv 1115 1125 1136 Th Tv=Tvd+Tvb
Active
Display
Blank Tvb Tv-Tvd 45 Tv-Tvd Th -
Total Th 1050 1100 1150 Tc Th=Thd+Thb
Active
Display
Blank Thb Th-Thd 140 Th-Thd Tc -
- - 200 ns (1)
T
rcl
TLVCCS 400 ps (2)
Fclkin_
mod
F
SSM
Tvd 1080 1080 1080 Th -
Thd 960 960 960 Tc -
Fc*98% Fc*102% MHz
200 KHz
(3)
INPUT SIGNAL TIMING DIAGRAM
Version 3.1 9 September 2011 15 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 16
Global LCD Panel Exchange Center
Note (1) The input clock cycle-to-cycle jitter is defined as below figures. Trcl = I T1 – TI
Note (2) Input Clock to data skew is defined as below figures.
www.panelook.com
PRODUCT SPECIFICATION
Note (3) The SSCG (Spread spectrum clock generator) is defined as below figures.
Note (4) The DCLK range at last line of V-blanking should be set in 0 to Hdisplay/2
Version 3.1 9 September 2011 16 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 17
Global LCD Panel Exchange Center
4.6 POWER ON/OFF SEQUENCE
The power sequence specifications are shown as the following table and diagram.
www.panelook.com
PRODUCT SPECIFICATION
Timing Specifications:
Parameters
T1 0.5 - 10 ms
T2 0 - 50 ms
T3 450 - - ms
T4 90 - - ms
T5 0 - 50 ms
T6 5 - 150 ms
T7 500 - - ms
Note (1) The supply voltage of the external system for the module input should be the same as the definition
of Vcc.
Note (2) When the backlight turns on before the LCD operation of the LCD turns off, the display may
momentarily become abnormal screen.
Note (3) In case of VCC = off level, please keep the level of input signals on the low or keep a high
impedance.
Note (4) T4 should be measured after the module has been fully discharged between power off and on
period.
Note (5) Interface signal shall not be kept at high impedance when the power is on.
Min Typ. Max
Values
Units
Note (6) CMI wonϗt take any responsibility for the products which are damaged by the customers not
following the Power Sequence.
Note (7) There might be slight electronic noise when LCD is turned off (even backlight unit is also off). To
avoid this symptom, we suggest "Vcc falling timing" to follow "t6 spec".
Version 3.1 9 September 2011 17 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 18
Global LCD Panel Exchange Center
5. OPTICAL CHARACTERISTICS
5.1 TEST CONDITIONS
Item Symbol Value Unit
Ambient Temperature Ta
Ambient Humidity Ha
Supply Voltage VCC 5 V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
LED Light Bar Input Current
Per Input Pin
PWM Duty Ratio D 100 %
LED Light Bar Test Converter Test OZ9998-8 Strings T4-8
5.2 OPTICAL SPECIFICATIONS
The relative measurement methods of optical characteristics are shown in 5.2. The following items should be
www.panelook.com
PRODUCT SPECIFICATION
25r2
50r10
IPIN 65 ± 1.95 mADC
oC
%RH
measured under the test conditions described in 5.1 and stable environment shown in Note (5).
Item Symbol Condition Min. Typ. Max. Unit Note
Red
Color
Chromaticity
(CIE 1931)
Center Luminance of White
(Center of Screen)
Contrast Ratio CR
Response Time
White Variation
Viewing Angle
Green
Blue
White
Horizontal
Vertical
Rx 0.633
Ry 0.351
Gx 0.322
Gy 0.630
=0q, TY =0q
T
Bx 0.152
By 0.050
Wx 0.313
Wy
L
C
TR - 1.5 2.5
T
F
GW T
Tx- + Tx+
Ty- + Ty+
x
CS-2000
R=G=B=255
Gray scale
=0q, TY =0q
T
x
=0q, TY =0q
x
CR Њ 10
Typ –
0.03
0.329
150 200 - cd/m2 (4), (5)
500 700 - - (2), (5)
- 3.5 5.5
70 - - % (5), (6)
90 65 -
Typ +
0.03
Deg. (1), (5)
- (1), (5)
ms (3)
Version 3.1 9 September 2011 18 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 19
Global LCD Panel Exchange Center
Note (1) Definition of Viewing Angle (Tx, Ty):
www.panelook.com
PRODUCT SPECIFICATION
Note (2) Definition of Contrast Ratio (CR):
The contrast ratio can be calculated by the following expression.
Contrast Ratio (CR) = L255 / L0
L255: Luminance of gray level 255
L 0: Luminance of gray level 0
CR = CR (5)
CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6).
Note (3) Definition of Response Time (T
R
, TF):
Version 3.1 9 September 2011 19 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 20
Global LCD Panel Exchange Center
Note (4) Definition of Luminance of White (LC):
www.panelook.com
PRODUCT SPECIFICATION
Measure the luminance of gray level 255 at center point
LC = L (5)
L (x) is corresponding to the luminance of the point X at Figure in Note (6).
Note (5) Measurement Setup:
The LCD module should be stabilized at given temperature for 40 minutes to avoid abrupt
temperature change during measuring. In order to stabilize the luminance, the measurement should
be executed after lighting Backlight for 40 minutes in a windless room.
Note (6) Definition of White Variation (GW):
Measure the luminance of gray level 255 at 9 points
GW = ( Minimum [L (1) ~ L (9)] / Maximum [L (1) ~ L (9)] ) *100%
Version 3.1 9 September 2011 20 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 21
Global LCD Panel Exchange Center
6.
RELIABILITY
Temperature Humidity Bias (THB) Ta= 50к , 80%RH, 240hours -
High Temperature Operation
Low Temperature Operation
High Temperature Storage (HTS)
Low Temperature Storage (LTS)
Thermal Shock Test (TST)
ESD (Electro Static Discharge)
Note (1) criteria : Normal display image with no obvious non-uniformity and no line defect.
TEST ITEM
Items Required Condition Note
(HTO)
(LTO)
Vibration Test
(Non-operation)
Shock Test
(Non-operation)
On/Off Test
Air Discharge: ± 15KV, 150pF(330ȍ) -
Altitude Test
www.panelook.com
PRODUCT SPECIFICATION
Ta= 5 0к , 50%RH , 240hours
Ta= 0 к , 240hours
Ta= 6 0к , 240hours
Ta= - 2 0 к , 240hours
Acceleration: 1.5 Grms
Wave: Half-sine
Frequency: 10 - 300 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)
Acceleration: 50 G
Wave: Half-sine
Active Time: 11 ms
Direction : ± X, ± Y, ± Z.(one time for
each Axis)
-20к/30min , 60к / 30min , 100
cycles
25к ,On/10sec , Off /10sec , 30,000
cycles
Contact Discharge: ± 8KV,
150pF(330ȍ)
Operation:10,000 ft / 24hours
Non-Operation:30,000 ft / 24hours
-
-
-
-
-
-
-
-
-
-
Note (2) Evaluation should be tested after storage at room temperature for more than two hours.
Note (3) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so
that the module would not be twisted or bent by the fixture.
The fixing condition is shown as below:
Version 3.1 9 September 2011 21 / 28
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 22
Global LCD Panel Exchange Center
7. PACKING
7.1 PACKING SPECIFICATIONS
(1) 13 LCD modules / 1 Box
(2) Box dimensions: 567(L) X 301(W) X 376(H) mm
(3) Weight: approximately: 27.525kg (13 modules per box)
7.2 PACKING METHOD
(1) Carton Packing should have no failure in the following reliability test items.