One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 3
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
REVISION HISTORY
Version Date Section Description
Ver 0.0
Ver 3.0
Nov., 16 ’04
Dec., 07 ‘04 - 1.5
7.2
8.1
8.2
9.2
M170E5-P01 Tentative Specifications was first issuedΖ
Increased product weight typ. 435g; max. 450g
Modified optical measurement machine from ˖˦ˀ˄˃˃˃ʳʳ˖˦ˀ˄˃˃˃˧
Increased weight 15kg
Increased Packing Method.
Modified the carton label
3 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 4
Global LCD Panel Exchange Center
1. GENERAL DESCRIPTION
1.1 OVERVIEW
The M170E5-P01 is a 17-inch TFT LCD cell with driver ICs and a 30-pin-and-2ch-LVDS circuit board.
The product supports 1280 x 1024 SXGA mode and can display up to 16.2M colors. The backlight unit is
not built in.
1.2 FEATURES
- Wide viewing angle
- High contrast ratio
- Fast response time
- High color saturation (EBU Like Specifications)
- SXGA (1280 x 1024 pixels) resolution
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
- DE (Data Enable) only mode
- LVDS (Low Voltage Differential Signaling) interface
1.3 APPLICATION
- TFT LCD Monitor
- TFT LCD TV
1.4 GENERAL SPECIFICATI0NS
Item Specification Unit Note
Active Area 337.92 (H) x 270.34 (V) (17.0” diagonal) mm
Bezel Opening Area 341.9 (H) x 274.4 (V) mm
Driver Element a-si TFT active matrix - Pixel Number 1280 x R.G.B. x 1024 pixel Pixel Pitch 0.264 (H) x 0.264 (V) mm Pixel Arrangement RGB vertical stripe - Display Colors 16.2M color Transmissive Mode Normally white - Surface Treatment Hard coating (3H), AG (Haze 25%) - -
(1)
1.5 MECHANICAL SPECIFICATIONS
Item Min. Typ. Max. Unit Note
Module size - - - (1)
Weight - 435 450 g -
I/F connector mounting
position
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
The mounting inclination of the connector makes
the screen center within ±0.5mm as the horizontal.
(2)
(2) Connector mounting position
+/- 0.5mm
4 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 5
Global LCD Panel Exchange Center
www.panelook.com
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT (LCD MODULE)
Item Symbol
Storage Temperature TST -20 +60 ºC (1)
Operating Ambient Temperature TOP 0 +50 ºC (1), (2)
Shock (Non-Operating) S
Vibration (Non-Operating) V
LCD Cell Life Time L
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta Љ 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The temperature of panel surface should be 0 ºC Min. and 60 ºC Max.
- 50 G (3), (5)
NOP
- 1.5 G (4), (5)
NOP
50,000 - Hrs
CELL
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Value
Min. Max.
Unit Note
Approval
MTBF
based
Note (3) 11ms, half-sine wave, 1 time for ± X, ± Y, ± Z…RA
Note (4) 10 ~ 300 Hz, sweep rate 10 min / cycle , 30 min for X,Y,Z axis.
Note (5) Upon the Vibration and Shock tests, the fixture used to hold the module must be firm and rigid
enough to prevent the module from twisting or bending by the fixture.
Relative Humidity (%RH)
100
90
80
60
Operating Range
40
20
Storage Range
5
Temperature (ºC)
5 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
8060 -20 400 20-40
www.panelook.com
Page 6
Global LCD Panel Exchange Center
www.panelook.com
2.2 ABSOLUTE RATINGS OF ENVIRONMENT (OPEN CELL)
High temperature or humidity may reduce the performance of panel. Please store LCD panel within
the specified storage conditions.
Storage Condition: With packing.
Storage temperature range: 25±5 ºC.
Storage humidity range: 50±10%RH.
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
Shelf life: 30days
2.3 ELECTRICAL ABSOLUTE RATINGS (OPEN CELL)
Item Symbol
Power Supply Voltage Vcc -0.3 +6.0 V
Logic Input Voltage VIN -0.3 4.3 V
Note (1) Permanent damage might occur if the module is operated at conditions exceeding the maximum
values.
Min. Max.
Value
Unit Note
(1)
6 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 7
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD OPEN CELL Ta = 25 ± 2 ºC
Parameter Symbol
Min. Typ. Max.
Power Supply Voltage Vcc 4.5 5.0 5.5 V Ripple Voltage VRP - -- 100 mV Rush Current I
- -- 3.8 A (2)
RUSH
White - 420 590 mA (3)a
Power Supply Current
Black - 570 800 mA (3)b
= 75Hz,
f
V
Vcc=4.5V
lcc
- - 1200 mA (4)
LVDS differential input voltage Vid -100 - +100 mV
LVDS common input voltage Vic -- 1.2 -- V
Logic “L” input voltage (SELLVDS) Vil Vss - 0.8 V
Note (1) The module is recommended to operate within specification ranges listed above for normal
function.
Value
Approval
Unit Note
Note (2) Measurement Conditions:
+5.0V
R1
47K
(High to Low)
(Control Signal)
SW
+12V
C1
1uF
VR1
R2
47K
1K
Q1 2SK1475
C2
0.01uF
Q2
2SK1470
FUSE
C3
1uF
Vcc
(LCD Module Input)
Vcc rising time is 470Ps
+5.0V
0.9Vcc
0.1Vcc
GND
470Ps
7 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 8
Global LCD Panel Exchange Center
Note (3)The specified power supply current is under the conditions at Vcc = 5.0 V, Ta = 25 ± 2 ºC, fv = 60
Hz, whereas a power dissipation check pattern below is displayed.
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
Note (4) The specified power supply current is under the conditions at Vcc = 4.5 V, Ta = 25 ± 2 ºC, f
a. White Pattern
Active Area
Hz, whereas a power dissipation check pattern (Black Pattern) below is displayed.
Black Pattern
b. Black Pattern
Active Area
= 75
v
Active Area
8 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 9
Global LCD Panel Exchange Center
4. BLOCK DIAGRAM
4.1 TFT LCD OPEN CELL
RXO0(+/-)
RXO1(+/-)
RXO2(+/-)
RXO3(+/-)
RXOC(+/-)
RXE0(+/-)
RXE1(+/-)
RXE2(+/-)
RXE3(+/-)
RXEC(+/-)
SELLVDS
Vcc
GND
(JAE-FI-XB30SRL-HF11)
INPUT CONNECTOR
www.panelook.com
LVDS INPUT /
TIMING CONTROLLER
DC/DC CONVERTER &
REFERENCE VOLTAGE
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
SCAN DRIVER IC
TFT LCD PANEL
(1280x3x1024)
DATA DRIVER IC
Approval
9 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Black
Red
Green
Blue
Cyan
Magenta
Yellow
White
Red(0) / Dark
Red(1)
Red(2)
:
:
Red(253)
Red(254)
Red(255)
0
0
1
1
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
:
:
:
:
1
1
1
1
1
1
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
Data Signal
Red Green Blue
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Green(0) / Dark
Gray
Scale
Of
Green
Gray
Scale
Of
Blue
Note (1) 0: Low Level Voltage, 1: High Level Voltage
Green(1)
Green(2)
:
:
Green(253)
Green(254)
Green(255)
Blue(0) / Dark
Blue(1)
Blue(2)
:
:
Blue(253)
Blue(254)
Blue(255)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
1
1
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
12 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 13
Global LCD Panel Exchange Center
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item SymbolMin. Typ. Max. Unit Note
Frequency Fc - 54 67.5 MHz -
LVDS Clock
LVDS Data
Vertical Active Display Term
Horizontal Active Display Term
NoteΚ(1) Because this module is operated by DE only mode, Hsync and Vsync input signals should be
Period Tc 14.8 18.5 - ns
High Time Tch - 4/7 - Tc Low Time Tcl - 3/7 - Tc Setup Time Tlvs 600 - - ps Hold Time Tlvh 600 - - ps Frame RateFr 56 60 75 Hz Tv=Tvd+Tvb
Total Tv 1034 1066 1274 Th Display Tvd 1024 1024 1024 Th Blank Tvb Tv-Tvd42 Tv-Tvd Th Total Th 690 844 960 Tc Th=Thd+Thb
Display Thd 640 640 640 Tc Blank Thb Th-Thd204 Th-Thd Tc -
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
set to low logic level or ground. Otherwise, this module would operate abnormally.
INPUT SIGNAL TIMING DIAGRAM
13 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 14
Global LCD Panel Exchange Center
6.2 POWER ON/OFF SEQUENCE
To prevent a latch-up or DC operation of LCD module, the power on/off sequence should follow the
conditions shown in the following diagram.
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
Note.
(1) The supply voltage of the external system for the module input should be the same as the definition of Vcc.
(2) Please apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD
operation of the LCD turns off, the display may, instantly, function abnormally.
(3) In case of
(4) T4 should be measured after the module has been fully discharged between power on/off periods.
(5) Interface signal shall not be kept at high impedance when the power is on.
VCC = off level, please keep the level of input signals on the low or keep a high impedance.
14 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 15
Global LCD Panel Exchange Center
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Symbol Value Unit
Ambient Temperature Ta
Ambient Humidity Ha
Supply Voltage VCC 5.0 V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
Inverter Current IL 6.5 mA
Inverter Driving Frequency FL 50 KHz
7.2 OPTICAL SPECIFICATIONS
The relative measurement methods of optical characteristics are shown as below. The following items
should be measured under the test conditions described in 7.1 and stable environment shown in Note (6).
Item Symbol Condition Min.Typ. Max. UnitNote
Red
Green
Blue
Color
Chromaticity
Center Transmittance T%
Contrast Ratio CR
Response Time
Transmittance uniformity
Viewing Angle
White
Red
Green
Blue
White
Horizontal
Vertical
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
o
25r2
50r10
Rcx 0.650
Rcy
0.343
Gcx 0.274
T
=0q, TY =0q
Gcy
Bcx 0.132
Standard light source “C”
x
CS-1000T
Typ -
0.03
Bcy
0.600
0.112
Typ +
0.03
Wcx 0.318
Wcy
Rx
Ry
Gx
Gy
Bx
By
Wx
Wy
T
=0q, TY =0q
x
CS-1000T
Typ -
0.03
CMO BLU
4.8 5.3 - cd/m2(1), (8)
0.361
0.645
0.346
0.281
0.606
0.142
0.068
0.313
0.329
Typ +
0.03
300450 - - (1), (3)
TR T
F
GT%
Tx+
T
-
x
TY+
-
T
Y
T
=0q, TY =0q
x
T
=0q, TY =0q
x
BM-5A
CRt10
BM-5A
-
- - 1.4 - (1), (7)
60 70 60 70 50 60 50 60 -
4 7
12 18
C
%RH
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
ms
ms
Deg.
(0),(6)
(1), (6)
(4)
(1), (2)
(6)
15 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 16
Global LCD Panel Exchange Center
7.3 Flicker Adjustment
(1) Adjustment Pattern: One-dot checker pattern as follows.
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
(2) Adjustment Method:
When adjusting Flicker, the pin 25 of input connector must be tide to VDD (3.3V). Flicker should be
adjusted by turning the volume for flicker adjustment by the ceramic driver. It is adjusted to the point with
least flickering of the whole screen. After making it surely overrun at once, it should be adjusted to the
optimum point.
16 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 17
Global LCD Panel Exchange Center
Note (0) Light source is the standard light source “C” which is defined by CIE and driving voltages are based on
suitable gamma voltages. The calculating method is as followingǺ
1. Measure Module’s and BLU’s spectrums. White is without signal input and R, G, B are with signal
input. BLU is supplied by CMO.
2. Calculate cell’s spectrum.
3. Calculate cell’s chromaticity by using the spectrum of standard light source “C”
Note (1) Light source is the BLU which is supplied by CMO and driving voltages are based on suitable gamma
voltages. White is without signal input and R, G, B are with signal input.
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
Note (2) Definition of Viewing Angle (Tx, Ty):
Note (3) Definition of Contrast Ratio (CR):
TX- = 90º
6 o’clock
T
y- = 90º
x-
y-
Normal
Tx = Ty = 0º
Ty-Ty
Tx
Tx
12 o’clock direction
y+
T
y+ = 90º
x+
TX+ = 90º
The contrast ratio can be calculated by the following expression.
Contrast Ratio (CR) = L255 / L0
L255: Luminance of gray level 255
L 0: Luminance of gray level 0
CR = CR (1)
CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (7).
17 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 18
Global LCD Panel Exchange Center
Note (4) Definition of Response Time (TR, TF):
100%
90%
Optical
Response
Gray Level 255
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
Gray Level 255
10%
0%
Note (5) Definition of Luminance of White (L
Measure the luminance of gray level 255 at center point
L
= L (1)
C
L (x) is corresponding to the luminance of the point X at Figure in Note (7).
Note (6) Measurement Setup:
The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt
temperature change during measuring. In order to stabilize the luminance, the measurement
should be executed after lighting Backlight for 20 minutes in a windless room.
LCD Module
Gray Level 0
T
RT
):
C
Time
F
LCD Panel
Center of the Screen
BM-5A
CS-1000T
Field of View = 2º
500 mm
Light Shield Room
(Ambient Luminance < 2 lux)
18 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 19
Global LCD Panel Exchange Center
Note (7) Definition of Transmittance Variation (GT%):
Measure the transmittance at 13 points
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
Maximum [L (1), L (2),……….L (12), L (13)]
GT% =
Minimum [L (1), L (2),…… ….L (12), L (13)]
D/10
D/4D/23D/4
D
9D/10
Vertical Line
W
W/10
W/4
W/2
3W/4
9W/10
6
23
9
4
11 1213
7
1
5
10
8
X
: Test Point
X=1 to 13
Active Area
Note (8) Definition of Transmittance(T%):
Module is without signal input.
Transmittance =
Luminance of LCD module
Ϡ 100%
Luminance of backlight
19 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 20
Global LCD Panel Exchange Center
8. PACKAGING
8.1 PACKING SPECIFICATIONS
(1) 20 open cells / 1 Box
(2) Box dimensions: 545(L) X 480(W) X 485(H) mm
(3) Weight: approximately 15 Kg (20 open cells per box)
8.2 PACKING METHOD
(1) Carton Packing should have no failure in the following reliability test items
Test Item Test Conditions Note
ISTA STANDARD
Packing
Vibration
Random, Frequency Range: 1 – 200 Hz
Top & Bottom: 30 minutes (+Z), 10 min (-Z),
Right & Left: 10 minutes (X)
Back & Forth 10 minutes (Y)
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
Non Operation
(2) Packing method.
20 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 21
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
21 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 22
Global LCD Panel Exchange Center
9. DEFINITION OF LABELS
9.1 CMO PANEL LABEL
The barcode nameplate is pasted on each cell as illustration for CMO internal control.
9.2 CARTON LABEL
The barcode nameplate is pasted on each box as illustration, and its definitions are as following explanation
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
(a) Model Name: M170E5 –P01
(b) Carton ID: CMO internal control
(c) Quantities: 20pcs
22 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 23
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Dec. 07, 2004
Model No.: M170E5-P01
Approval
10. PRECAUTIONS
10.1 ASSEMBLY AND HANDLING PRECAUTIONS
(1) Do not apply rough force such as bending or twisting to the product during assembly.
(2) To assemble backlight or install module into user’s system can be only in clean working areas. The
dust and oil may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel will be
damaged.
(4) Always follow the correct power sequence when the product is connecting and operating. This can
prevent damage to the CMOS LSI chips during latch-up.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and
easily scratched.
(7) It is dangerous that moisture come into or contacted the product, because moisture may damage the
product when it is operating.
(8) High temperature or humidity may reduce the performance of module. Please store this product within
the specified storage conditions.
(9) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the
response time will become slowly.
10.2 SAFETY PRECAUTIONS
(1) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
(2) After the product’s end of life, it is not harmful in case of normal operation and storage.
23 / 24
Version 3.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 24
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.