ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 14
Global LCD Panel Exchange Center
www.panelook.com
SPEC NO.
PAGE
BT156GW01 V.A
12/24
f. Backlight driving conditions
Parameter Symbol Min. Typ. Max. Unit Remark
LED Forward Voltage V
LED Forward Current
LED Power consumption
Input PWM frequency F
3 3.2 3.4 V
F
IF 20 mA
P
3.93 4.20 W
LED
P
2.50 2.70 W
LED-G
200 1000 2000 Hz T = 25C
PWM
rms
rms
T = 25C
T = 25C
T = 25C
Note 1
Duty ratio - 5 100 % Note 2
LED life time (LED only) - 15,000 Hr T = 25C , Note 3
Note 1: The BL power consumption @100 nits with full white pattern under the V
C, f
=60Hz (frame frequency) condition
V
=3.3 V, 25
cc
Note 2: PWM duty ratio linearity guarantees 10~100%.
Note 3: LED life time definition is brightness decrease to 50% of initial or abnormal lighting.
g. Module function block
LED Light-bar
Gate driver
TFT-LCD
Source driver
LED driver
Timing
controller
Step-up regulator
& reference voltage
generator
EDID
EEPROM
LVDS connector
LVDS DATA BUS mini-LVDS & CONTROL BUS POWER I2C BUS
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 15
Global LCD Panel Exchange Center
www.panelook.com
h. LED circuit block
LED Driving
Circuit
6 parallels
& 9 series
SPEC NO.
PAGE
LED_P
BT156GW01 V.A
13/24
FB1
FB2
FB3
FB4
FB5
FB6
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 16
Global LCD Panel Exchange Center
к
www.panelook.com
3. Optical specifications
Item Symbol Condition
Response time
Contrast ratio CR
Viewing angle
SPEC NO.
PAGE
BT156GW01 V.A
14/24
Ambient temperature = 25
Specification
Min. Typ. Max.
Tr+Tf = 0ш
= 0ш
500 600 Note 2,4
8 15 ms Note 3
Unit Remark
Top 15
Bottom 30
CRЊ10
Left 40
Right
40
deg Note 2,4,6
Top 6
Brightness
(5 points average)
Color chromaticity (CIE)
Color gamut NTSC CIE1931 56 60 % -
White uniformity
Bottom 11
CRЊ100
Left 25
Right
Y
200 220 nit Note 2,5
L
Wx
Wy
Rx
Ry
Gx
= 0ш
Gy
Bx
B
y
1.25
W(5)
25
0.313
0.329
0.620
0.340
-0.03
+0.03
0.330
0.605
0.150
0.070
Note 2
Note 2,7
1.5
W(13)
Cross talk Ct 2% Note 8
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 17
Global LCD Panel Exchange Center
(
Avg
www.panelook.com
SPEC NO.
PAGE
Note 1: To be measured in dark room.
Note
2: To be measured with a viewing cone of 2°by Topcon luminance meter BM-5A.
Note 3: Definition of response time:
The output signals of BM-7 are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time
interval is between 10% and 90% of amplitudes. Refer to figure as below.
"Black"
100%
S
ig
90%
n
a
l(
R
e
la
t
iv
e
v
a
lu
10%
e
)
0%
Tr
Tf
BT156GW01 V.A
15/24
"White""White"
Note 4: Definition of contrast ratio:
Contrast ratio is calculated with the following formula:
Contrast ratio
of 5pts) =
Note 5: Driving current for LED should be 20 mA.
Luminance is measured at the following thirteen points (1~13):
Y
= (Y5+ Y10+Y11+Y12 +Y13) / 5
L
Note 6: Definition of viewing angle
L
white (Avg of 5pts.)
L
Black (Avg of 5pts.)
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 18
Global LCD Panel Exchange Center
www.panelook.com
Note 7: Definition white uniformity
Luminance is measured at the following thirteen points (1~13):
Ӭ
Maximum brightness of thirteen points
W(13)!=
Minimum brightness of thirteen points
Ӭ
W(5)!=
13 point measuring locations refer to the point 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 and 13.
5 point measuring locations refer to the point 5, 10, 11, 12 and 13.
Maximum brightness of five points
Minimum brightness of five points
SPEC NO.
PAGE
BT156GW01 V.A
16/24
Note 8:
1/2
1/6
A
1/6
B
1/2
32 gray level 32 gray level
Unit: percentage of dimension of display area
l L
l L
l / LA x 100%= 2% max., LA and LA’ are brightness at location A and A’
A-LA’
l / LB x 100%= 2% max., LB’ and LB’ are brightness at location B and B’
B-LB’
2/31/3
1/2
A’
0 gray level
1/6
1/6
1/3
1/2
B’
2/3
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 19
Global LCD Panel Exchange Center
www.panelook.com
4. Reliability test items
Test Item Test Condition Judgment Remark
High temperature storage
Low temperature storage
High temperature & high
humidity operation
High temperature operation
Low temperature operation
Thermal shock
(Non-operation)
60к, 240 hours
-20к, 240 hours
40к, 90% RH, 240 hours
(No condensation)
50к, 240 hours
0к, 240 hours
-25к / 30 mins ~ 65к / 30 mins
100 cycles
SPEC NO.
PAGE
BT156GW01 V.A
17/24
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Note 1 Note 2
Electrostatic discharge (ESD)
Vibration
(Non-operation)
Mechanical shock
(Non-operation)
Contact: ±8kV, Air: ±15kV
1.5G, 10 to 500 Hz random; 0.5hr in each
perpendicular axes ( X, Y, Z ).
220G/2ms, Half sine wave, ±X, ±Y, ±Z one
time for each direction
Note 1
Note 1 Note 2
Note 1 Note 2
Note 1: Pass: Normal display image with no obvious non-uniformity and no line defect.
Fail: No display image, obvious non-uniformity, or line defects.
Partial transformation of the module parts should be ignored.
Note 2: Evaluation should be tested after storage at room temperature more than one hour.
150 pF, 330,
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 20
Global LCD Panel Exchange Center
www.panelook.com
5. Safety
5-1. Sharp edge requirements
There will be no sharp edges or corners on the display assembly that could cause injury.
5-2. Materials
a. Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials
are used, they will be reviewed and approved by the responsible InnoLux Toxicologist.
b. Flammability
All components including electrical components that do not meet the flammability grade UL94-V0
in the module will complete the flammability rating exception approval process. The printed circuit
board will be made from material rated 94-V0 or better. The actual UL flammability rating will be
SPEC NO.
PAGE
BT156GW01 V.A
18/24
printed on the printed circuit board.
c. Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep
them from being inserted backwards.
6. Display quality
The display quality of the color TFT-LCD module should be in compliance with the InnoLux
incoming inspection standard.
7. Handling precaution
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) To assemble or install module into user’s system can be only in clean working areas. The
dust and oil may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and
backlight will be damaged.
(4) Always follow the correct power sequence when LCD module is connecting and
operating.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is
very soft and easily scratched.
(8) It is dangerous that moisture come into or contacted the LCD module, because moisture
may damage LCD module when it is operating.
(9) High temperature or humidity may reduce the performance of module. Please store LCD
module within the specified storage conditions.
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM INNOLUX DISPLAY CORPORATION.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!