How it Works
chiliGREEN
Loading...
D620S U
User Manual
209 pgs3.7 Mb0
Table of contents
Loading...

chiliGREEN D620S U User Manual

Download
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no re­sponsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, man­ufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufactur­er.

Preface

©May 2002
I
Preface

Trademarks

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intel­lectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home or other limited viewing uses only unless otherwise authorized by Mac­rovision Corporation. Reverse engineering or disassembly is prohib­ited.
Intel and Pentium are registered trademarks of Intel Corporation. MS-DOS and Windows are registered trademarks of Microsoft Cor-
poration.
II

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in­stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi­sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV techni­cian for help.
Preface

Warning

Use only shielded ca­bles to connect I/O de­vices to this equipment. You are cautioned that changes or modifica­tions not expressly ap­proved by the manufacturer for com­pliance with the above standards could void your authority to oper­ate the equipment.
III
Preface
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
IV
USE THE APPROPRIATE 26AGW TELEPHONE
LINE CORD
IMPORTANTES MESURES DE SÉCURITÉ
1. Ne pas utiliser l’appareil près de l’eau,, p.ex., près d’une baignoire, d’un lavabo, d’un évier de cuisine, d’un bac à laver, dans un sous-sol humide ou près d’une piscine.
2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil sans fil) pen­dant un orage électrique. Ceci peut présenter un risque de choc élec­trique causé par la foudre.
3. Ne pas utiliser l’appareil téléphonique pour signaler une fuite de gaz s’il est situé près de la fuite.
4. Utiliser seulement le cordon d’alimentation et le type de piles indiqués dans ce manuel. Ne pas jeter les piles dans le feu: elles peuvent exploser. Se conformer aux règlements pertinents quant à l’émination des piles.
ATTENTION
Débranchez toujours toutes les lignes téléphoniques des prises mu­rales avant de réparer ou de démonter cet équipement.
Preface
UTILISEZ LE CORDON DE TÉLÉPHONE 26AGW
APPROPRIÉ
V
Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To ensure that does not happen, follow these suggestions:
1. Don’t drop it. Make sure it’s on a stable surface. If the compu-
ter falls, the case and other components could be damaged. Do not expose it to any shock or vibration.
2. Don’t overheat it. Keep the computer and power supply away
from any kind of heating element. Keep the computer out of direct sunlight. Don’t store or use the computer in a humid envi­ronment. Do not place the computer on any surface which will block the vents.
3. Avoid interference. Keep the computer away from high capac-
ity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data.
4. Keep it dry. This is an electrical appliance. If water or any other
liquid gets into it, the computer could be badly damaged. Do not leave it in a place where foreign matter or moisture may affect the system.
VI
5. Follow the proper working procedures for computer. Shut- down the computer properly, and close all programs (don’t for­get to save your work). Do not turn off any peripheral devices when the computer is on. Do not disassemble the computer by yourself. Remember to periodically save your data as data may be lost if the battery is depleted. Perform routine maintenance on your computer.
6. Take care when using peripheral devices. Use only approved brands of peripheral devices. Unplug the power cord before attaching any peripheral device.
7. Do not place anything heavy on the computer.
Preface
VII
Preface

Power Safety

The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a quali­fied electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC adapter or car adapter).
• Do not plug in the power cord if you are wet.
• Do not use the power cord if it is broken.
• Do not place heavy objects on the power cord.
VIII

Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Recharge the batteries using the notebook’s system. Incorrect recharg­ing may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service person­nel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Caution
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Preface

Battery Disposal

The product that you have purchased con­tains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this bat­tery into the municipal waste stream. Check with your local solid waste officials for de­tails in your area for re­cycling options or proper disposal.
IX
Preface

Cleaning

Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may vio­late your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to quali­fied service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poison­ous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
X

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC adapter and cables. Stow them in the carry­ing bag.
5. The AC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However, check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hardware and software. Make sure your “papers” are handy (it may be useful to have the computer in standby mode before going through customs).
Preface
XI
Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 7: Troubleshooting. Keep these points in mind:
Hand-carry the notebook.
Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard ob­jects.
Beware of Electromagnetic fields.
Metal detectors & X-ray machines These devices can damage the computer, hard disk and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them. (you may be asked to turn it on.) Note: Some airports also scan luggage with these devices.
XII
Fly safely.
Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, fol­low them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can.
If an electrical outlet is available, use the AC adapter and keep your battery(ies) charged.
Keep it dry.
If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.
Preface
XIII
Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to re­duce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back com­fortably.
• Sit straight so that your knees, hips and elbows form approximately 90­degree angles when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
XIV

Remember to:

• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
Preface
XV
Preface

Lighting

Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.
• Position the display to avoid glare or reflections from overhead light­ing or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display viewing angle to find the best position.
XVI
Contents
Notice .............................................................................................. I
Trademarks ..................................................................................... II
Federal Communications Commission (FCC) Statement .............III
Instructions for Care and Operation ..............................................VI
Power Safety ..............................................................................VIII
Battery Precautions .......................................................................IX
Cleaning ......................................................................................... X
Servicing ......................................................................................... X
Travel Considerations ...................................................................XI
Introduction ........................................... 1-1
Overview ......................................................................................1-1
The Manual ..................................................................................1-2
Advanced Users ............................................................................1-2
Beginners and Not-So-Advanced Users .......................................1-2
Warning Boxes .............................................................................1-3
Not Included .................................................................................1-4
System Software ...........................................................................1-4
Quick Start Guide .........................................................................1-5
System Map ..................................................................................1-6
Preface
XVII
Preface
Getting to Know Your Computer ................................................ 1-6
Models ......................................................................................... 1-7
Top View with LCD Panel Closed .............................................. 1-8
Top View with LCD Panel Open ................................................. 1-9
LCD Panel ................................................................................. 1-10
LED Power & Auto Mail Indicators .......................................... 1-10
Close Cover Switch ...................................................................1-10
Stereo Speakers .......................................................................... 1-10
LED Status Indicators ................................................................ 1-11
Hot-Key Buttons ........................................................................ 1-11
Power Button ............................................................................. 1-12
Keyboard .................................................................................... 1-12
TouchPad & Buttons .................................................................. 1-13
Microphone ................................................................................ 1-13
Left Side View ........................................................................... 1-14
Security Lock ............................................................................. 1-14
Right Side View ......................................................................... 1-15
Microphone-In Jack ................................................................... 1-15
Headphone-Out Jack .................................................................. 1-16
S/PDIF Out Port ......................................................................... 1-16
Mini - IEEE 1394 Port ............................................................... 1-16
Three USB Ports ........................................................................ 1-17
XVIII
Optional 3.5" USB FDD (Floppy Disk Drive) ...........................1-17
PC Card Slot ...............................................................................1-17
CD Device ..................................................................................1-18
Infrared Transceiver ...................................................................1-19
Rear View ...................................................................................1-20
RJ-11 Phone Jack .......................................................................1-20
RJ-45 LAN Jack .........................................................................1-21
Printer/Parallel Port ....................................................................1-21
External Monitor (CRT) Port .....................................................1-21
S-Video Port ...............................................................................1-21
PS/2 Type Port ...........................................................................1-22
DC-In Jack ..................................................................................1-22
Bottom View ..............................................................................1-23
Using The Computer ............................. 2-1
Overview ......................................................................................2-1
The Power Sources .......................................................................2-2
AC Adapter ..................................................................................2-2
Battery ..........................................................................................2-3
Recharging Battery with the AC Adapter ....................................2-4
Proper handling of the Battery Pack ............................................2-4
Turning on the Computer .............................................................2-5
Preface
XIX
Preface
LED Indicators ............................................................................. 2-6
LED Status Indicators .................................................................. 2-7
LED Power & Communication Indicators .................................. 2-8
Auto Mail Checker ...................................................................... 2-9
Special Group ............................................................................2-11
The Hard Disk Drive (HDD) ..................................................... 2-12
The USB Floppy Disk Drive (FDD) .......................................... 2-13
Inserting/Removing Floppy Disks ............................................. 2-13
The CD Device .......................................................................... 2-14
Loading Discs ............................................................................ 2-14
Handling CD’s or DVD’s .......................................................... 2-15
DVD Regional Codes ................................................................ 2-16
Changing the DVD Regional Codes .......................................... 2-17
The PC Card Slot ....................................................................... 2-18
Inserting and Removing PC Cards ............................................ 2-18
Hot-Keys .................................................................................... 2-19
Function Keys ............................................................................ 2-22
The Numeric Keypad ................................................................. 2-23
Function Keys and Numeric Keypad ......................................... 2-24
TouchPad and Buttons ............................................................... 2-25
Configuring the TouchPad and Buttons .................................... 2-26
XX
Mouse .........................................................................................2-27
Adding a Printer .........................................................................2-28
USB Printer ................................................................................2-28
Install Instructions: .....................................................................2-28
Parallel Printer ............................................................................2-29
Install Instructions: .....................................................................2-29
Advanced Controls ................................ 3-1
Overview ......................................................................................3-1
Advanced Video Controls ............................................................3-2
Opening the LCD .........................................................................3-2
Video Driver Controls ..................................................................3-3
Making Adjustments for the Display ...........................................3-4
Display Properties ........................................................................3-5
SiS Utility Tray/Manager .............................................................3-6
Video Memory .............................................................................3-8
Display Devices ............................................................................3-9
Display Options ..........................................................................3-10
Switching/Enabling Displays (Keyboard Toggle) .....................3-11
Switching/Enabling Displays (Driver Controls) ........................3-12
Attaching a Monitor (CRT) ........................................................3-14
Mirror .........................................................................................3-15
Preface
XXI
Preface
Multimonitor .............................................................................. 3-15
TV Display ................................................................................. 3-16
Power Management Features ..................................................... 3-17
Enabling Power Options ............................................................ 3-18
Conserving Power Through Individual Components ................ 3-19
Monitor Standby ........................................................................ 3-19
Hard Disk Standby ..................................................................... 3-19
Conserving Power Throughout the System ............................... 3-20
Hibernate Mode vs. Shutdown .................................................. 3-20
Standby Mode vs. Hibernate Mode ........................................... 3-20
Standby ...................................................................................... 3-21
Hibernate .................................................................................... 3-22
Configuring the Power Button ................................................... 3-23
Battery Information ................................................................... 3-24
New Battery ............................................................................... 3-24
Battery Life ................................................................................ 3-24
Battery FAQ ............................................................................... 3-25
Conserving Battery Power ......................................................... 3-26
Display Brightness ..................................................................... 3-26
Applications and External Devices ............................................ 3-26
Removing and Replacing the Battery ........................................ 3-27
XXII
Drivers & Utilities ................................. 4-1
Overview ......................................................................................4-1
What to Install ..............................................................................4-2
Authorized Driver Message .........................................................4-3
Version Conflict Message ............................................................4-3
Windows 2000 Professional .........................................................4-5
Audio (Win2000) .........................................................................4-5
Modem (Win2000) .......................................................................4-5
LAN (Win2000) ...........................................................................4-6
Video (Win2000) ..........................................................................4-7
TouchPad (Win2000) ...................................................................4-7
Hot-Key (Win2000) .....................................................................4-8
Auto Mail (Win2000) ...................................................................4-8
Windows XP ................................................................................4-9
Audio (WinXP) ............................................................................4-9
Modem (Win XP) .......................................................................4-10
LAN (Win XP) ...........................................................................4-11
Video (WinXP) ..........................................................................4-12
TouchPad (WinXP) ....................................................................4-12
Hot-Key (WinXP) ......................................................................4-13
Auto Mail (WinXP) ....................................................................4-13
Preface
XXIII
Preface
BIOS Utilities .........................................5-1
Overview ...................................................................................... 5-1
Important BIOS Settings .............................................................. 5-2
The Power-On Self Test (POST) ................................................. 5-3
POST Screen ................................................................................ 5-4
Failing the POST .........................................................................5-5
Fatal Errors .................................................................................. 5-5
Non-Fatal Errors .......................................................................... 5-5
The Setup Program ...................................................................... 5-6
Entering Setup ............................................................................. 5-6
Setup Screens ............................................................................... 5-7
Main Menu ................................................................................... 5-8
Advanced Menu ......................................................................... 5-10
Security Menu ............................................................................ 5-14
Boot Menu ................................................................................. 5-16
Exit Menu ..................................................................................5-18
Upgrading The Computer .....................6-1
Overview ...................................................................................... 6-1
When Not to Upgrade .................................................................. 6-2
Upgrading the CD Device ........................................................... 6-3
XXIV
Upgrading the Hard Disk Drive ...................................................6-5
Removing the Hard Disk ..............................................................6-6
Some Things to Watch Out For ....................................................6-8
Software .......................................................................................6-8
Setting Up a New HDD ................................................................6-8
Upgrading the System Memory ...................................................6-9
Removing the Keyboard .............................................................6-10
Troubleshooting ..................................... 7-1
Overview ......................................................................................7-1
Basic Hints and Tips ....................................................................7-2
Backup and General Maintenance ................................................7-4
Viruses ..........................................................................................7-5
Upgrading and Adding New Hardware/Software ........................7-6
Power ............................................................................................7-8
Display .......................................................................................7-15
Hard Disk Drive (HDD) .............................................................7-19
Boot Password ............................................................................7-19
Floppy Disk Drive (FDD) ..........................................................7-20
Audio ..........................................................................................7-21
CD Device ..................................................................................7-22
PC Card ......................................................................................7-25
Preface
XXV
Preface
Keyboard and Mouse ................................................................. 7-26
Printer ........................................................................................ 7-27
Operation ................................................................................... 7-30
Glossary .................................................G-1
A ................................................................................................. G-1
B .................................................................................................. G-1
C .................................................................................................. G-2
D ................................................................................................. G-3
F .................................................................................................. G-3
G ................................................................................................. G-4
H ................................................................................................. G-4
I ................................................................................................... G-4
J ................................................................................................... G-5
K ................................................................................................. G-5
L .................................................................................................. G-5
M ................................................................................................. G-6
N ................................................................................................. G-7
P .................................................................................................. G-7
R .................................................................................................. G-9
S .................................................................................................. G-9
T ................................................................................................ G-11
XXVI
U ................................................................................................G-11
V ................................................................................................G-11
Z ................................................................................................G-12
Appendix A. Specifications .................. A-1
Processor .....................................................................................A-1
Core Logic ...................................................................................A-1
Structure ......................................................................................A-1
Security ........................................................................................A-2
Memory .......................................................................................A-2
BIOS ............................................................................................A-2
LCD .............................................................................................A-2
Display ........................................................................................A-3
Storage .........................................................................................A-3
Audio ...........................................................................................A-4
PC Card .......................................................................................A-4
Interface .......................................................................................A-5
Communication ...........................................................................A-5
Power Management .....................................................................A-6
Power ...........................................................................................A-6
Indicators .....................................................................................A-6
Environmental Spec ....................................................................A-6
Preface
XXVII
Preface
Physical Dimensions ................................................................... A-7
Weight ......................................................................................... A-7
Optional ...................................................................................... A-7
XXVIII

Chapter 1: Introduction

Overview

What this chapter covers:
• The Manual — how to use it
• Quick Start Guide — the minimum you need to know
• System Map — navigating around your computer
Introduction
1
Overview 1 - 1
1
Introduction

The Manual

5
Advanced Notes
Advanced users should check the light colored boxes with the mark above.
This is where you will find detailed informa­tion about the compu­ter’s features.
Beginners may refer to this area also, and you may be surprised how much you understand.
This manual refers to the hardware and essential software required to run your notebook computer. Depending on how your system is con­figured, some or all of the features described may already be set up.

Advanced Users

If you are an advanced user you may skip over most of this manual. However you may find it useful to refer to the “Drivers & Utilities”
on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1. You may also find the notes marked with
a 5 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers, or do not have an advanced knowledge of them, then you should try to look through all the documentation. Do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the beginner’s notes marked with a as indicated in the margin.
1 - 2 The Manual

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the symbol. Also please note the safety and handling instructions as indicated in the Preface.
Introduction
1
The Manual 1 - 3
1
Introduction

Not Included

Operating Systems (e.g. Windows 2000 Professional, Windows XP etc.) have their own manuals as do applications (e.g. word process-
ing, spreadsheet and database programs). If you have questions about the operating systems or programs then please consult the ap­propriate manuals.

System Software

Your computer may already come with system software pre-in­stalled. Where this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the following operating systems:
• Microsoft Windows 2000
• Microsoft Windows XP
1 - 4 Not Included

Quick Start Guide

This guide assumes that you are already familiar with computers and can tell at a glance what and where all the key components are. If you are not that comfortable with this type of device, then please refer to the following pages, which give an overview of the system.
It is still best to review these steps, before taking any action. If there is anything you are not sure about, then please refer to the appropri­ate chapter before continuing.
1. Remove all packing materials, CD’s/DVD’s, floppy disks, and any PC Cards.
2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
3. Attach the AC adapter to the DC-in jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC adapter
4. Raise the lid/LCD to a comfortable viewing angle.
5. Press the power button to turn “on”.
Introduction

Peripheral Devices

Please note that pe­ripherals (printers, dig­ital cameras, etc.) which attach to your computer by either USB or IEEE1394 ports may be connect­ed after Windows is up and running. All other peripherals must be connected before you turn on the system.
1
Quick Start Guide 1 - 5
1
Introduction

System Map

Your notebook PC has a lot of built-in features. Most of these are en­abled by your operating system. Further explanations of the various subsystems are covered in the chapter or pages indicated.

Getting to Know Your Computer

The following graphics will help you to become familiar with the ba­sic functions, and to learn the location of the various ports and com­ponents of your computer.
1 - 6 System Map

Models

Model A Model B
Introduction
Model Differences
This manual refers to three notebook models pictured on this page.
The models vary slightly in external de­sign. Photographs used throughout this manual are of Model A.
Figure 1 - 1
Model Differences
1
Model C
System Map 1 - 7
1
Introduction
Figure 1 - 2
Top View with LCD
Panel Closed
1. LCD Latch
2. LED Power & Auto Mail Indicators

Top View with LCD Panel Closed

2
1
To open the LCD display:
1. Place the computer on a stable surface.
2. Move the cover latch “1” to the right, and hold it, to release the
top cover.
3. Lift the top cover to reveal the LCD panel and keyboard.
4. Adjust the LCD panel to a comfortable viewing angle.
5. The LED Power & Auto Mail Indicators “2” show the power
source and power status of the computer, and give notification of e-mail received.
1 - 8 System Map
Introduction
1

Top View with LCD Panel Open

1
3
2
4 45 6
8
9
3
4 4
5
2
6
Figure 1 - 3
Top View with LCD
Panel Open
1. LCD
2. LED Power & Auto Mail Indicators
3. Close Cover Switch
4. Speakers
7
10
7
5. LED Status Indicators
6. Hot-Key Buttons
7. Power Button
8. Keyboard
9. TouchPad and Buttons
10. Microphone
System Map 1 - 9
1
Introduction
LCD Panel
The notebook PC comes with a 14.1" XGA 1024x768 TFT OR 15.0" XGA 1024x768 TFT LCD (Liquid Crystal Display) screen depend­ing upon the configuration purchased.
LED Power & Auto Mail Indicators
These indicators display the current power source and power source status of the computer. The third indicator may be configured to give a visual confirmation when e-mail is received in the default e-mail program (see “Auto Mail Checker” on page 2 - 9).
Close Cover Switch
This switch acts as a sensor to tell when the LCD Panel is closed. When this LCD cover sensor is activated the default setting of your operating system’s power scheme sends the computer into a power saving state (see “Power Options (Schemes)” on page 3 - 19).
Stereo Speakers
1 - 10 System Map
Two built-in speakers provide rich, stereo sound.
LED Status Indicators
These display the system’s operational status. Refer to “LED Status Indicators” on page 2 - 7 for more information on what the lights
mean.
Hot-Key Buttons
The three Hot-Keys allow you instant access to your default internet browser, default e-mail program, and an application of your choice. To learn how to set the buttons see “Hot-Keys” on page 2 - 19.
Introduction
1
System Map 1 - 11
1
Introduction
Power Button
Press this button to turn your computer on or off (see “ Turning on the Computer” on page 2 - 5). This button may also be used as a
suspend/resume key, once configured as such in the power
Shutdown
Please note that you should always shut your computer down by choosing the Shut
Down/Turn Off Com­puter command from
the Start menu in Win­dows. This will help
prevent hard disk or system problems
management control panel of your operating system (see “Configuring the Power Button” on page 3 - 23).
5
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds to force the system to turn itself off.
Keyboard
The computer has a “Win Key” keyboard with an embedded numeric keypad. It has the same features as a full-sized desktop keyboard and can easily be replaced with a different language keyboard should you desire.
1 - 12 System Map
TouchPad & Buttons
The pointing device features a sensitive glide pad for precise move­ments. It functions the same way as a two-button mouse. The right TouchPad button is the same as the right mouse button; the left TouchPad button is the same as the left mouse button. The central buttons may be used to scroll up and down, or they may be config­ured to perform a variety of function (see “Configuring the Touch- Pad and Buttons” on page 2 - 26).
Microphone
Record on your notebook computer with the built-in microphone.
Introduction
1
System Map 1 - 13
1
Introduction
Figure 1 - 4

Left Side View

1. Security Lock
2. Vent
Overheating
To prevent your com­puter from overheating make sure nothing blocks the vent while the computer is in use.
Left Side View
1
Security Lock
To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store.
Vent
This enables airflow to prevent the notebook from overheating.
2
1 - 14 System Map
Introduction
1

Right Side View

1 2 3
7 8
4 5
9
6
Microphone-In Jack
Record on your notebook computer with an external microphone.
10
Figure 1 - 5
Right Side View
1. Microphone-In Jack
2. Headphone-Out Jack
3. S/PDIF Out Port
4. Mini IEEE 1394 Port
5. Three USB Ports
6. USB FDD (optional)
7. PC Card Slot
8. PC Card Eject Button
9. CD Device
10. Infrared Port
System Map 1 - 15
1
Introduction
Headphone-Out Jack
Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack.
S/PDIF Out Port
You can use this port for S/PDIF (Sony/Philips Digital Interface For­mat) output, which allows you to connect your DVD-capable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound.
Mini - IEEE 1394 Port
This allows high speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below).
5
IEEE 1394
The IEEE 1394 port only supports SELF POWERED IEEE 1394 devices.
1 - 16 System Map
Three USB Ports
These ports are hardware interfaces for low-speed peripherals such as a keyboard, mouse, joystick, scanner, printer or telephony devic­es. Devices may be plugged into the computer, and unplugged from the computer, without the need to turn the system off.
Optional 3.5" USB FDD (Floppy Disk Drive)
Your computer may have a 3.5" USB, 1.44 MB floppy disk option (see "6" in Figure 1 - 5 “Right Side View” on page 1 - 15) depend­ing on the configuration purchased. For more information please re­fer to “The USB Floppy Disk Drive (FDD)” on page 2 - 13.
PC Card Slot
This is a type II 3.3V/5V/12V PC card slot (also previously referred to as PCMCIA) supporting CardBus. Refer to “The PC Card Slot” on page 2 - 18 for more information on the PC Card slot.
Introduction
Media Warning
Don’t try to remove a floppy disk while the system is accessing it. This may cause the system to “crash”.
1
System Map 1 - 17
1
Introduction
CD Device
CD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the Emergency eject hole.
A 5.25” CD-ROM drive, or DVD-ROM drive, or CD-RW, or Com­bination CD-RW and DVD-ROM Drive (12.7mm height) is standard depending on the model you purchased. For more information on us­ing the drive please refer to “The CD Device” on page 2 - 14.
2
41
3
Do not use a sharp­ened pencil or similar object that may break and become lodged in the hole.
Figure 1 - 6
CD Device
1 - 18 System Map
1. CD-ROM or DVD label to indicate which type
2. Busy Indicator
3. Open button
4. Emergency eject hole
Infrared Transceiver
Introduction
1
Infrared
Communication
The Infrared transceiv­er operates on a “Line of Sight”.
Make sure nothing is blocking the “Line of Sight” between your system’s transceiver and the destination’s transceiver.
System Map 1 - 19
1
Introduction
Figure 1 - 7

Rear View

1. RJ-11 Phone Jack
2. RJ-45 LAN Jack
3. Parallel Port
4. Vent
5. External Monitor (CRT) Port
6. S-Video Port
7. PS/2 Type Port
8. DC-In Jack
Rear View
2 3 4 5 7 861
Overheating
To prevent your computer from overheating make sure nothing blocks the vent while the computer is in use.
RJ-11 Phone Jack
This port connects to the built-in modem. You may plug the tele­phone line directly into this RJ-11 telephone connection. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
1 - 20 System Map
RJ-45 LAN Jack
This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Printer/Parallel Port
This port supports ECP (Extended Capabilities Port) and EPP (En­hanced Parallel Port) 1.7/1.9 modes.
External Monitor (CRT) Port
Connect an external CRT monitor to this port to allow dual video or simultaneous display on the LCD and external CRT monitor (see “ Display Devices” on page 3 - 9).
S-Video Port
Connect your television to your computer and view DVD’s, VCD’s or anything else your computer can display. You will need an S-Vid­eo cable to make the connection. Enable this port from the video driver controls (see “ TV Display” on page 3 - 16).
Introduction
1
System Map 1 - 21
1
Introduction
PS/2 Type Port
Connect an external PS/2 type mouse or keyboard to this port. You can use a “Y” splitter if you want to attach both.
DC-In Jack
Plug the supplied AC adapter into this jack to power your notebook.
1 - 22 System Map
Introduction
1

Bottom View

Figure 1 - 8
Bottom View
1
2
1
2
5
3
4
1. CD Device Release Latch
2. Vents/Fan Outlets
3. HDD Bay
4. Battery
5. Battery Release Latch
Overheating
To prevent your com­puter from overheating make sure nothing blocks the vent/fan outlets while the com­puter is in use.
System Map 1 - 23
1
Introduction
1-24
Using The Computer

Chapter 2: Using The Computer

Overview

Your notebook computer can be used almost anywhere, in the home, office, or on the road. To learn more about your computer, please read this chapter.
This chapter includes:
•The Power Sources
• Turning on the Computer
• The LED Indicators
• The Hard Disk Drive
• The Floppy Disk Drive
• The CD Device
•The PC Card Slot
•The Hot-Keys
• The Function Keys
• The Numeric Keypad
• The TouchPad and Buttons
• Adding a Printer
2
Overview 2 - 1
Using The Computer
2
Standby or Hibernate
5
Power Button as
Button

The Power Sources

Either an AC adapter or a battery pack can power the computer.

AC Adapter

Only use the AC adapter that comes with your computer. The wrong
If you are using an ACPI-compliant OS, such as Windows 2000
Professional, or Win­dows XP the power
button can be desig­nated as Standby or Hibernate within the OS’s “Power Options” subsystem (see your OS’s documentation,
“Power Manage-
or
ment Features” on page 3 - 17 for de-
tails).
type of AC adapter will damage the computer and its components.
1. Attach the AC adapter to the DC-in jack at the rear of the computer.
2. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “on”.
2 - 2 The Power Sources
Using The Computer

Battery

The battery allows you to use your notebook computer while you are on the road, or an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before re­charging.
We recommend leaving the battery inside the notebook at all times. For more information on the battery, please refer to “Battery Infor- mation” on page 3 - 24.
2
Figure 2 - 1
Battery Removed
The Power Sources 2 - 3
Using The Computer
2
The battery pack automatically recharges when the AC adapter is at­tached and plugged into an electrical outlet. If the computer is pow­ered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electri­cal outlet, battery charge time is reduced (refer to “LED Power & Communication Indicators” on page 2-8 for information on the battery charge status).
Proper handling of the Battery Pack
• DO NOT disassemble the battery pack under any circumstances.
• DO NOT expose the battery to fire or high temperatures, it may
explode.
• DO NOT connect the metal terminals (+, -) to each other (for more
information on how to maintain the battery pack, refer to
Information” on page 3 - 24).
“Battery

Recharging Battery with the AC Adapter

2 - 4 The Power Sources
Using The Computer

Turning on the Computer

Now you are ready to begin using your notebook computer. To turn it on simply press the power button on the top right of the front panel. When the computer is turned on, the Power Button can also be used as a Standby/Hibernate/Shutdown hot-key button if pressed for less than 4 seconds (pressing and holding the Power Button for longer than this will shut the computer down) and is appropriately config­ured in the OS Control Panel (Power Options).
Power Button
5

Forced Off

If the Ctrl + Alt + Del key combination doesn’t work when the system “hangs”, press the power button for 4 seconds, or longer, to force the system to turn itself off.
Figure 2 - 2
Power Options
Shutdown
Always shut your com­puter down by the
Shut Down/Turn Off Computer command from the Start menu in Windows.
2
Turning on the Computer 2 - 5
Using The Computer
2

LED Indicators

There are two sets of LED indicators (LED Status Indicators and LED Power & Automail Indicators) on your computer. These dis-
play helpful information about the current status of the computer.
1. LED Status Indicators
2. LED Power & Auto Mail Indicators
2
Figure 2 - 3
LED Indicators
1
2 - 6 LED Indicators
Using The Computer

LED Status Indicators

Icon Color Description
Green The Hard Drive is being accessed
Green Number Lock is activated
Green Caps Lock is activated
Green Scroll Lock is activated
2
Num Lock
For more information on the number lock feature see “The Nu-
meric Keypad” on page 2 - 23.
Table 2 - 1
LED Status
Indicators
LED Indicators 2 - 7
Using The Computer
2

LED Power & Communication Indicators

Icon Color Description
Orange AC Power is plugged in
Green The computer is turned on
Table 2 - 2
LED Power & Auto
Mail Indicators
Blinking Green
Orange The battery is being charged
Green The battery is fully charged
Blinking Orange
Blinking Green New mail has arrived.
Fast Blinking Green
The system has entered the
configured standby mode
The battery has reached criti-
cally low power status
New mail has arrived from users
defined in the Special Group in
Auto Mail Checker.
2 - 8 LED Indicators
Using The Computer

Auto Mail Checker

After you have installed the driver for the Auto Mail program (see “What to Install” on page 4 - 2) you may then configure it to give
notification when new mail is received. You must be online to re­ceive this notification (note that this program only supports the POP3 protocol), and your default mail program does not need to be open.
The Auto Mail Checker appears as an icon in the taskbar. Click­ing on the icon will bring up the following options menu.
Select Open to bring up the control panel for the program.
2
Auto Mail Checker 2 - 9
Using The Computer
2
Check with your Inter­net Service Provider, network administrator or Mail Service provid­er for details on what to put on these pages.

Note

word, program and method(s) of notification.
Figure 2 - 4
AutoMail
Checker Account
Setup and
Options
You may then configure the options for your mailserver, name, pass-
2 - 10 Auto Mail Checker
Using The Computer

Special Group

You may also define the users you want to appear in this group (see Figure 2 - 5). If you choose to enable the Mail LED then the
icon will blink when you receive new mail in your default mail pro­gram.
You may add the e-mail addresses of those you wish to assign to your special group here. The LED will then blink fast when mail is re­ceived from members of this group if LED notification is enabled in the control panel (Figure 2 - 4).
2
Figure 2 - 5
Special Group Setup
Auto Mail Checker 2 - 11
Using The Computer
2
Before attempting to access any of the inter­nal components of your notebook please insure that the ma­chine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral ca­bles, including phone lines, are disconnected from the computer.

Power Safety

Figure 2 - 6
Hard Disk
Location

The Hard Disk Drive (HDD)

The hard disk drive is used to store your data in the notebook com­puter. It is mounted in a removable case and can be taken out to ac­commodate other 2.5" (9.5mm) height IDE hard disk drives. The system supports PIO mode 4 /ATA-33/66/100.
The hard disk is accessible from the bottom of your computer as seen below, "1" (remove screw "2"). Further details on removing and in­serting the hard disk are available in “Upgrading the Hard Disk Drive” on page 6 - 5.
1
2
2 - 12 The Hard Disk Drive (HDD)
Using The Computer

The USB Floppy Disk Drive (FDD)

You may have an external 1.44 MB, 3.5” USB floppy disk drive module depending on the configuration purchased. By default it is drive "A:" and can be used as a boot device if properly set in the
BIOS. For more information refer to “Boot Menu” on page 5 - 16.
Note: If your configuration does not include the FDD you may pur-
chase an external USB FDD.

Inserting/Removing Floppy Disks

When using the floppy drive, always insert your floppy diskette with the label-side facing up. To remove the inserted diskette, press the eject button on the floppy drive.
2

Media Warning

Don’t try to remove a floppy disk while the system is accessing it. This may cause the computer to “crash” and damage your data.
The USB Floppy Disk Drive (FDD) 2 - 13
Using The Computer
2
Sound Volume
Adjustment
You may set the vol­ume adjustment from the volume control within Windows. Click the Speaker icon on the taskbar to check the settings.

The CD Device

Depending on the configuration purchased, your system may have one or more CD devices. If present in a standard configuration, one will appear as drive "D:".

Loading Discs

To insert a CD/DVD disc, press the Open Button and carefully place a CD/DVD disc onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks”. The Busy Indicator will light up while data is being accessed or while an audio CD/DVD is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole to open the tray.
2 - 14 The CD Device
Using The Computer

Handling CD’s or DVD’s

Proper handling of your CD’s will prevent them from being dam­aged. Please follow the advice below to make sure that the data stored on your CD-ROM / DVD-ROM discs can be accessed.
Remember to:
• Hold the CD or DVD by the edges; do not touch the surface of the disc.
• Use a clean, soft, dry cloth to remove dust or fingerprints.
• Do not write on the surface with a pen.
• Do not attach paper or other materials to the surface of the disc.
• Do not store or place the CD or DVD in high-temperature areas.
• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
• Do not bend the CD or DVD.
• Do not drop or subject the CD or DVD to shock.
CD Emergency Eject
If you need to manually eject a CD (e.g. due to an unexpected power in­terruption) you may push the end of a straightened paper clip into the emergency eject hole.
Media Warning
When manually eject­ing a CD/DVD disc, DO NOT use a sharp­ened pencil or similar object which, may break and become lodged in the hole.
2
The CD Device 2 - 15
Using The Computer
2
Multiple Display
Modes & DVD
Playback
In Mirror mode DVD movies must be dis­played in the primary device - see “Switch-
ing/Enabling Dis­plays (Driver Controls)” on page 3
- 12.
DVD playback is not supported in Multi- monitor mode.
Figure 2 - 7
DVD Regional
Codes
(Windows XP)
DVD region detection is device dependent, not OS dependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.

DVD Regional Codes

2 - 16 The CD Device
Using The Computer
Changing the DVD Regional Codes
Region (tab) to bring up the control panel as seen in “DVD Regional
Codes (Windows XP)” on page 2 - 16.
DVD Regional Coding
Region Geographical Location
1 USA, Canada
2 Western Europe, Japan, South Africa, Middle East & Egypt
3 South-East Asia, Taiwan, South Korea, The Philippines,
Indonesia, Hong Kong
4 South & Central America, Mexico, Australia, New Zealand
5 N Korea, Russia, Eastern Europe, India & Most of Africa
6China
2
Table 2 - 3
DVD Regional
Coding
The CD Device 2 - 17
Using The Computer
2

The PC Card Slot

The computer is equipped with a type II PCMCIA 3.3V/5V/12V socket.

Inserting and Removing PC Cards

• Align the PC card with the slot "1" and push the card in until it locks into place.
• To remove a PC card, simply press the eject button "2" next to the slot.
Figure 2 - 8
PC Card Slot
1
2
2 - 18 The PC Card Slot
Using The Computer

Hot-Keys

The computer has three Hot-Key buttons for quick one button access to e-mail ("1"), the Internet ("2") or a user-defined application ("3"). To make full use of the Hot-Key features you must install the Hot­Key driver (see “What to Install” on page 4 - 2).
2 31
2
Figure 2 - 9
Hot-Keys
Hot-Keys 2 - 19
Using The Computer
2
Non-Default E-Mail
It is possible to config­ure both the email and browser hot-keys to open non-default mail and browser pro­grams. Follow the pro­cedure outlined on page 2 - 21 but high­light either the Brows- er or Email in step 2. Choose Custom to browse to the program of your choice as per the remaining instruc­tions. The Hot-Key will now open this pro­gram.
and Browser
Programs
Table 2 - 4
Hot-Keys
Hot-Keys Function
Activate the default e-mail program
Activate the default Internet browser
Activate the user specified application (e.g. Microsoft Word or Excel
After installing the Hot-Key driver (see “What to Install” on page 4
- 2), you may have to configure or change the settings.
To configure and specify an application for Application 1 (the de­fault Hot-Key setting is for the CD Player application), you must follow the instructions on the next page.

Programming the Hot-Keys

2 - 20 Hot-Keys
Using The Computer
1. Right click the Hot-Key icon on the taskbar and the fol-
lowing menu will appear.
2. Select Setup from the menu and scroll to Application 1 and press Enter.
3. An Open dialog box will appear on the screen.
4. Browse to the directory where the desired application.exe (see the sidebar) program exists.
5. Double-Click on the program file or choose Open.
6. The Hot-Key is now set to execute that program.
2
Application.exe
You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application right-click its shortcut on the desktop and click Properties. Click the shortcut (tab) and see where the execut­able file is located by clicking the Find Tar-
get (button).
Hot-Keys 2 - 21
Using The Computer
2
If your keyboard is damaged, or you just want to make a change, you can use any standard PS/2 or USB keyboard. The system will detect and enable it automatically. However special func­tions/hot-keys unique to the system’s regular keyboard may not work.
5

Other Keyboards

Table 2 - 5

Function Keys

On the bottom-left of the keyboard is the Fn key, or Function key. The Fn key allows you to change some of the operational features of your computer instantly. Press and hold the Fn key, then press the appropriate function key (F3, F4, F5, etc.) located at the top of the keyboard (see “Figure 2 - 10 Function Keys & Numeric Keypad” on page 2 - 24).
Keys Description
Fn+F3 Mute Toggle Fn+F4 Suspend/Resume Fn+F5 Audio Volume Decrease Fn+F6 Audio Volume Increase Fn+F7 Switch Display between LCD, CRT & LCD and CRT Fn+F8 LCD Brightness Decrease Fn+F9 LCD Brightness Increase
Function Keys
2 - 22 Function Keys
Using The Computer

The Numeric Keypad

The keyboard has an embedded numerical keypad for easy numeric data input. The keypad has a yellow typeface.
To use the embedded keypad simply activate the Number Lock fea­ture by pressing and holding the Fn key, while simultaneously press­ing the Num Lk key at the top right of the keyboard. You may check if Num Lk is enabled or not by looking at the LED status indicators (see “LED Status Indicators” on page 2-7).
You may type the numbers directly from the embedded keypad as long as Num Lk is enabled.
5

Special Characters

Some software appli­cations allow the number-keys to be used with Alt to pro­duce special charac­ters. These special characters can only be produced by using the numeric keypad. Reg­ular number keys will not work. Make sure
Number Lock is on.
2
The Numeric Keypad 2 - 23
Using The Computer
2

Function Keys and Numeric Keypad

Figure 2 - 10
Function Keys & Numeric Keypad
2 4
3
1
1. Fn Key
2. Mute Toggle
3. Suspend/Resume State Toggle
4. Audio Volume Decrease
5. Audio Volume Increase
6. CRT/LCD/LCD and CRT Toggle
7. LCD Brightness Decrease
8. LCD Brightness Increase
9. Num Lk
10. Scr Lk
11. Numeric Keypad
5
76 8
9 10
11
2 - 24 The Numeric Keypad
Using The Computer

TouchPad and Buttons

The pointing device features a sensitive glide pad for precise move­ments. Its functions the same way as a two-button mouse (the central Rocker Switch may be configured as a “third” button if you prefer). The right TouchPad button is the same as the right mouse button; the left TouchPad button is the same as the left mouse button.
2
TouchPad and Buttons 2 - 25
Using The Computer
2
Figure 2 - 11
Mouse Properties
Once you have installed the TouchPad driver, (see “What to In­stall” on page 4 - 2) you can configure the functions by double- clicking the TouchPad driver icon on the taskbar to bring up the Mouse Properties control panel (Figure 2 - 11). You may then con-
figure the TouchPad tracking, buttons and Rocker Switch etc. to your preferences. You will find further information on this at www.syn­aptics.com.

Configuring the TouchPad and Buttons

2 - 26 TouchPad and Buttons
Using The Computer

Mouse

You can also add a mouse to your notebook computer. You can use a mouse through either the PS/2 interface or through one of the USB ports.
5
Mouse Driver
If you are using an ex­ternal mouse your op­erating system may be able to auto-configure your mouse during its installation or only ena­ble its basic functions. Be sure to check the device’s user docu­mentation for details.
2
TouchPad and Buttons 2 - 27
Using The Computer
2

Adding a Printer

The most commonly used peripheral is a printer. The following con­ventions will help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options.

USB Printer

Most new printers have a USB interface connection. There are three USB ports on your notebook computer and you may use any one of the ports to connect the printer.
Install Instructions:
1. Set up the printer according to its instructions (unpacking, paper tray, toner/ink cartridge etc.).
2. Turn ON the computer.
3. Turn ON the printer.
4. Connect the printer’s USB cable to one of the USB ports on the computer.
5. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instruc­tions.
2 - 28 Adding a Printer
Using The Computer

Parallel Printer

This is still the most common type of printer.
Install Instructions:
1. Set up the printer according to its instructions (unpacking, paper tray, toner/ink cartridge etc.).
2. Attach the parallel cable to the printer.
3. Connect the printer’s parallel cable to the parallel port at the rear of the computer (see “Rear View” on page 1 - 20).
4. Turn ON the printer.
5. Turn ON the computer.
6. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instruc­tions.
2
Adding a Printer 2 - 29
Using The Computer
2
2-30

Chapter 3: Advanced Controls

Advanced Controls

Overview

This chapter covers:
• Advanced video controls
• Power and battery management features
3

Drivers

You are unable to use most advanced con­trols until the neces­sary drivers and utilities are properly in­stalled. If your system hasn’t been properly configured (your serv­ice representative may have already done that for you), refer to “What
to Install” on page 4 ­2, for installation in-
structions.
Overview 3 - 1
Advanced Controls

Advanced Video Controls

3
Protecting the LCD
Do not allow any for­eign objects (i.e. paper or plastic) to get be­tween the lid/LCD and the work panel. They could damage or scratch the LCD and/or accidentally activate the close cover switch.
Figure 3 - 1
Brightness
Controls

Opening the LCD

As you open the lid, adjust it so you can look at the screen straight on, without any glare. If necessary, adjust the brightness controls (Fn + F8/F9).
F8 F9
Fn
3 - 2 Advanced Video Controls

Video Driver Controls

The video interface lets you change the screen resolution and color output to whatever is most comfortable/efficient for you. This is a matter of hardware, video memory and the driver for your operating system. The driver interface shows the available options.
You can switch display devices from the Display Properties control panel in Windows as long as the video driver is installed (“What to Install” on page 4 - 2).
Depending on the configuration purchased, the LCD is capable of supporting the following resolutions, as long as the video driver is in­stalled:
• 14.1" XGA TFT LCD - resolution = 1024 * 768
• 15.0" XGA TFT LCD - resolution = 1024 * 768
Advanced Controls
5
Screen Resolution/
Area Note
You may set the reso­lution to a higher set­ting than the panel supports, however this will require you to pan (scroll) around the screen as the display area will be larger than what you can see on the LCD.
3
Video Driver Controls 3 - 3
Advanced Controls

Making Adjustments for the Display

The higher the resolution you set the LCD for, the more information
3
the LCD can display on screen. To change the LCD’s resolution and color depth go to the Display Properties control panel:
1. Click Start, point to Settings and click Control Panel (if you are in Category View choose Appearance and Themes).
2. Double-click Display (icon).
3. In the Display Properties dialog box, click Settings (tab).
4. In Screen area/resolution, move the slider to the preferred setting for resolution (see "1" in Figure 3 - 2 on page 3-5).
5. In Colors/Color quality, click the arrow and scroll to the pre- ferred setting for color depth (see "2" in Figure 3 - 2 on page
3-5).
3 - 4 Video Driver Controls
Display Properties
2
1
3
When the Display Properties control panel is open, click the Ad­vanced "3" (button) to bring up the options tabs. Clicking through
these tabs allows you to make any video adjustments you require.
Advanced Controls
Figure 3 - 2
Advanced
Display
Properties
3
Video Driver Controls 3 - 5
Advanced Controls

SiS Utility Tray/Manager

With the video driver installed additional control panels are avail-
3
Figure 3 - 3
SiS Utility Tray/
Manager
Windows XP
able. To get to the control panels do the following:
1. Click Start, point to Settings and click Control Panel (if you are in Category View choose Appearance and Themes).
2. Double-click Display (icon).
3. In the Display Properties dialog box, click Settings (tab).
4. Click Advanced (button), and click SiS Utility Manager (tab).
5. Choose the setting you wish to change.
OR
1. Right-Click the SiS Utility Tray icon in the taskbar.
2. Point to Display Properties and choose the setting you wish to change.
3 - 6 Video Driver Controls
SiS Utility Tray icon
You may make changes to the Driver Mode Setting, Video Settings, Gamma Correction Settings (for VGA monitors) and General Infor­mation by clicking the appropriate tab and adjusting the setting. Some screen examples are shown below.
Advanced Controls
Figure 3 - 4
SiS Utility Tray/
Manager Setting
Tabs
3
Video Driver Controls 3 - 7
Advanced Controls

Video Memory

5
3

Video Memory Usage

3D Applications, such as games and CAD software, tend to re­quire more video mem­ory than most other applications. Check your application’s user documentation for vid­eo memory require­ments.
The computer does not have dedicated video memory. It makes use of a portion of system memory as video memory. By default, the vid­eo memory is set to 32MB. You may also set it to 16MB or 64MB (maximum) in the BIOS (see “Embedded Share Memory (Ad- vanced Menu>Advanced Chipset Control)” on page 5 - 11). Bear in mind that the more overall memory is used as video memory, the less is available as system memory. This memory is allocated from your system memory e.g. if your computer has 128MB of memory (RAM), then 32MB will be allocated to video leaving the system with 96MB of RAM.
3 - 8 Video Memory

Display Devices

Besides the built-in LCD, you can also use an external CRT connect­ed to the VGA port as your display device. You may also connect a TV. The following are the display options:
1. The built-in LCD (Single).
2. A CRT (external monitor) connected to the external monitor
(CRT) port at the rear of the computer (Single).
3. A TV connected to the S-Video port at the rear of the computer
(Single).
4. The built-in LCD and a CRT showing the same Image (Mirror).
5. The built-in LCD and a TV showing the same Image (Mirror).
6. The built-in LCD and a CRT showing different Images
(Multimonitor).
7. The built-in LCD and a TV showing different Images
(Multimonitor).
8. A CRT and TV showing different images (Multimonitor) - see
sidebar note.
The table on the following page shows the available options.
Advanced Controls
5
CRT and TV Display
setting
If you intend to use a TV and CRT as your display devices, the TV must be set as the pri­mary Display_1, and the CRT as the sec­ondary Display_2 (Figure 3 - 8 on page
3-16).
3
Display Devices 3 - 9
Advanced Controls

Display Options

3
Multiple Display
Modes & DVD
Playback
Display Mode Windows XP Windows 2000
In Mirror mode DVD movies must be dis­played in the primary device - see “Switch-
ing/Enabling Dis­plays (Driver Controls)” on page 3
- 12.
DVD playback is not supported in Multi- monitor mode.
Table 3 - 1
Display Options
3 - 10 Display Options
Single
Mirror
Multimonitor
Single - Either the LCD, CRT or TV as a display device. Mirror - The LCD, CRT or TV outputting the same view. Multimonitor -The LCD, CRT or TV outputting a different view (Win-
dows XP only).
33
33
3
Not Available

Switching/Enabling Displays (Keyboard Toggle)

To simply switch display devices, or enable other devices, with the Fn + LCD/CRT (F7) toggle do the following:
1. Plug the CRT or TV into the appropriate port.
2. Press and hold the Fn key, while simultaneously pressing the F7 key.
3. You may toggle through the options to display the LCD only, the LCD and the external display together, and the external display alone (make sure you allow time for the screens to refresh as you toggle through).
Note: If you only use the keyboard toggle to switch through the dis­play options you will not have the all the configuration options avail­able to you. If you want to use the options listed in “Display Options” on page 3 - 10 then use the driver control panel to config­ure the settings as per “Switching/Enabling Displays (Driver Con- trols)” on page 3 - 12.
Advanced Controls
3
Display Options 3 - 11
Advanced Controls

Switching/Enabling Displays (Driver Controls)

With the video driver installed, you also can use its built-in controls
3
Figure 3 - 5
Disable Auto
to do the switching. If you have not installed the video driver, refer to (see “What to Install” on page 4 - 2) for setup instructions. To use the display options from the video driver control panel do the fol­lowing:
1. Plug the CRT or TV into the appropriate port.
2. Following the instructions in “SiS Utility Tray/Manager” on page 3 - 6, and choose Driver Mode Setting.
3. If the device listbox doesn’t show any plugged in devices uncheck the Auto option.
3 - 12 Display Options
4. If you have chosen the mirror option, choose which device is to be primary, and which is to be secondary.
5. Click OK > OK to apply the settings (you may need to give your CRT a few seconds to refresh).
6. Click Yes to keep the settings.
7. If you have chosen the Multimonitor option, choose which device is to be Display_1, and which is to be Display_2.
8. Click OK >Yes to restart your computer.
9. Upon restart the displays will be configured for you.
10. You can reconfigure the displays from the Display Properties
> Settings control panel (see “Display Properties” on page 3
- 15).
Advanced Controls
3
Display Options 3 - 13
Advanced Controls

Attaching a Monitor (CRT)

3

Vertical Refresh Rate

The vertical refresh rate of your CRT is impor­tant. If it is too low and/ or you’re using fluores­cent lighting, the screen will appear to flicker. To reduce flickering on a CRT, use faster refresh rates (we recommend a refresh rate of 72Hz or more). But first check your monitor’s docu­mentation to make sure it can support the rates listed by the video driv­er. The default refresh rate for VGA monitors (without drivers) is 60Hz.
Figure 3 - 6
Monitor
Properties
If you prefer to use a monitor (CRT) you may change the vertical re­fresh rate from the following control panel:
3 - 14 Attaching a Monitor (CRT)

Mirror

In this mode the display of the two devices is the same.
Multimonitor
This mode allows a desktop to span the displays to acts as a large work area, thus creating a lot more screen area for display. Use the Display Properties control panel to drag the monitors to match the physical arrangement you wish to use.
Advanced Controls

Multimonitor

Use the Display Prop­erties control panel to drag the monitors to match the physical ar­rangement you wish to use. In the example shown in Figure 3 - 7 the primary monitor “1” is on the left, the other display is on the right.
Drag any icons or win­dows across to the oth­er display desktop. It is therefore possible to have one program visi­ble in one of the moni­tors, and a different program visible in the other monitor.
3
Windows XP
Figure 3 - 7
Display
Properties
Attaching a Monitor (CRT) 3 - 15
Advanced Controls

TV Display

5
3
CRT and TV Display
setting
If you intend to use a TV and CRT as your display devices, the TV must be set as the pri­mary Display_1, and the CRT as the sec­ondary Display_2 (see Figure 3 - 8).
Figure 3 - 8
CRT and TV
Display
To display desktop images on a TV display, connect the TV to your LCD PC by using an S-Video cable from the TV to the port at the rear of the computer. Follow the instructions in “Switching/En- abling Displays (Driver Controls)” on page 3 - 12. The TV system format may be switched between PAL and NTSC in the BIOS (see
“TV System (Advanced Menu>Advanced Chipset Control)” on page 5 - 12). You can also adjust the TV Scan Line Mode from the
BIOS.
3 - 16 TV Display

Power Management Features

To conserve power, especially when using the battery, your note­book computer uses ACPI power management. Power management conserves power by controlling individual components of the com­puter (the monitor and hard disk drive) or the whole system.

Advanced Configuration and Power Interface (ACPI)

Advanced Controls

OS Note

Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system. (Note: All pictures used on the following pages are from the Windows XP OS).
3
Power Management Features 3 - 17
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use