Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©April 2006
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended fo r home
or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Intel, Celeron, and Intel Core are trademarks/registered trademarks of Intel Corporation.
I
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
II
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sin k or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (DC Output 19V, 3.42A minimum AC/DC
Adapter, OR by a DC Output 20V, 4.5A minimum AC/DC Adapter if you are using the optional p ort replicator -
see pages 7 - 13 & C - 5).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
This Computer’s Optical Device is a Laser Class I Product
III
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
IV
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g procedu res for t he computer. Shut the computer down proper ly and don ’t for ge t
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
5. Take care when using peripheral devices.
Use only approved brands of
peripherals.
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
V
Preface
Power Safety
The computer has specific power requirements:
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
VI
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for intern ational travel but it still re quires a steady,
uninterrupted power supply. If you are unsure of your local power specifications, consult
your service representative or local power company.
• The power adapter may have either a 2-pr ong or a 3-prong ground ed plug. The third prong
is an important safety feature; do not defeat its purpose. If you do not have access to a
compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be su re to disconnect it by the plug head, not by
its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load
of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service repre sent ative or qualified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
VII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before turning the computer on.
VIII
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However ,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or requ ire proof of ownershi p for both hard-
ware and software. Make sure your “papers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
IX
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
X
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly belo w the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on
a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.
XI
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
XII
Contents
Notice ................................................................................. I
FCC Statement .............................................................II
Instructions for Care and Operation ..........................IV
Power Safety ..............................................................VI
Battery Precautions ...................................................VII
Cleaning .................................................................. VIII
Servicing ................................................................. VIII
Travel Considerations ................................................IX
Preface
System Map: Left View ...............................................1-11
System Map: Right View .............................................1-12
System Map: Bottom View ..........................................1-13
Windows XP Start Menu & Control Panel ..................1-14
Video Features .............................................................1-15
Display & Graphics Properties .................................1-16
Display Devices & Options .......................................1-17
Power Management Features .......................................1-18
Quick Start Guide
Overview ........................................................................1-1
Model & Design Differences .......................................1-2
Advanced Users ...........................................................1-3
Beginners and Not-So-Advanced Users ......................1-3
Warning Boxes ............................................................1-3
Not Included ................................................................1-4
System Software ..........................................................1-4
System Startup ...............................................................1-5
System Map: Top View with LCD Panel Open ............1-6
LED Indicators ................................................. .... ..........1-7
Hot Key Buttons & Keyboard .......................................1-8
Function Keys ...................................................... .... .... ..1-9
System Map: Front & Rear Views ...............................1-10
Features & Components
Overview ........................................................................2-1
Hard Disk Drive .............................................................2-2
Optical (CD/DVD) Device ............................................2-3
Loading Discs ..............................................................2-3
Handling CDs or DVDs ...............................................2-4
DVD Regional Codes ..................................................2-5
7-in-1 Card Reader .........................................................2-6
ExpressCard Slot ............................................................2-7
Inserting and Removing ExpressCards ........................2-7
Function Keys ................................................................2-8
Recording Audio ........................................................2-10
TouchPad and Buttons/Mouse .....................................2-12
Configuring the TouchPad and Buttons ...................2-12
XIII
Preface
Audio Features .............................................................2-13
8 Channel Sound Support .........................................2-14
Adding a Printer ...........................................................2-15
USB Printer .......................................................... ....2-15
Parallel Printer ..........................................................2-15
Power Management
Overview ........................................................................3-1
Advanced Configuration and Power Interface ............3-1
The Power Sources ........................................................3-2
AC/DC Adapter ................................................. .... .... ..3-2
Battery .........................................................................3-2
Turning on the Computer ...............................................3-3
Power Schemes ..............................................................3-4
System Power Options ...................................................3-6
Hibernate Mode vs. Shutdown ....................................3-6
Stand by Mode vs. Hibernate Mode ............................3-6
Stand by ......................................................................3-7
Hibernate ....................................................................3-7
Configuring the Power Button .......................................3-8
Battery Information .......................................................3-9
New Battery ................................................................3-9
Battery Life .................................................................3-9
Recharging the Battery with the AC/DC Adapter .....3-10
Proper handling of the Battery Pack .........................3-11
Battery FAQ ..............................................................3-12
Drivers & Utilities
What to Install ............................................................... .4-1
Module Driver Installation ..........................................4-1
Service Packs ...............................................................4-3
Authorized Driver Message .........................................4-4
Version Conflict Message ...........................................4-4
Updating/Reinstalling Individual Drivers ...................4-4
Driver Installation ..........................................................4-5
Driver Installation Application ...................................4-5
New Hardware Found ..................................................4-6
Service Pack Installation .............................................4-6
WinXP Driver Installation Procedure ..........................4-7
Chipset ........................................................................ 4-7
IAA (Intel Application Accelerator) ...........................4-7
Video (VGA) ..............................................................4-8
Audio ..........................................................................4-8
LAN ............................................................................4-8
Modem ........................................................................ 4-9
TouchPad .................................................................... 4-9
Card Reader/ExpressCard ........................................4-10
Hot Key ....................................................................4-10
PC Camera ................................................................4-10
Wireless LAN ...........................................................4-10
XIV
Preface
Bluetooth ..................................................................4-10
Port Replicator ..........................................................4-10
BIOS Utilities
Overview ........................................................................5-1
The Setup Utility ...................................................... .... ..5-2
Entering Setup ............................................................5-2
Setup Screens ..............................................................5-2
Main Menu .....................................................................5-3
System Time & Date (Main Menu) ...............................5-3
Advanced Menu .............................................................5-4
Boot Configuration (Advanced Menu) ..........................5-5
IDE Configuration (Advanced Menu) ...........................5-5
SATA Configure as > IDE Configuration
(Advanced Menu) ..........................................................5-5
Video Configuration > IGD - DVMT Size:
(Advanced Menu) ..........................................................5-5
Setting Up AHCI SATA Mode ..................................5-6
Security Menu ................................................................5-8
Set Supervisor Password (Security Menu) ....................5-8
Set User Password (Security Menu) .............................. 5-9
Power Menu .................................................................5-10
Advanced CPU Control (Power Menu) .......................5-10
Boot Menu ...................................................................5-11
Exit Menu ....................................................................5-12
Upgrading The Computer
Overview ........................................................................6-1
When Not to Upgrade ..................................................6-2
Removing the Battery ....................................................6-3
Upgrading the Hard Disk Drive .....................................6-4
Upgrading the Optical (CD/DVD) Device ....................6-6
Upgrading the System Memory (RAM) ........................6-7
Upgrading the Processor ..............................................6-10
Modules & Options
Overview ........................................................................7-1
PC Camera ..................................................... .... .... ........7-2
PC Camera Driver Installation ...................................7-3
PC Camera Audio Setup .............................................7-4
BisonCap .....................................................................7-6
Eliminating Screen Flicker .........................................7-7
PC Camera Hot Keys ...................................................7-8
Intel WLAN Module ......................................................7-9
Intel WLAN Driver Installation ...............................7-10
Bluetooth Module ........................................................7-11
Bluetooth Driver Installation ....................................7-11
Port Replicator .............................................................7-13
Port Replicator Setup Instructions: ...........................7-14
Port Replicator Serial (COM) Port Driver (WinXP) 7-14
Port Replicator Network (LAN) Driver (WinXP) ....7-15
XV
Preface
Troubleshooting
Overview ........................................................................8-1
Basic Hints and Tips ......................................................8-2
Backup and General Maintenance .................................8-3
Viruses ........................................................................... 8-4
Upgrading and Adding New Hardware/Software ..........8-5
Power .............................................................................8-7
Display ........................................................................... 8-9
Boot Password .............................................................8-10
Audio & CD Device ............................................ .... ....8-11
Keyboard ......................................................................8-12
Operation .....................................................................8-13
Modules .......................................................................8-14
Interface (Ports & Jacks)
Overview .......................................................................A-1
Notebook Ports and Jacks .............................................A-2
Card Reader Port .......................................................... .A-2
DC-In Jack ....................................................................A-2
External Monitor (VGA) Port .......................................A-2
Headphone-Out Jack .....................................................A-2
Line-In Jack ..................................................................A-2
Microphone-In Jack ......................................................A-2
Mini-IEEE 1394 Port ....................................................A-3
RJ-11 Phone Jack ..........................................................A-3
RJ-45 LAN Jack ............................................................A-3
Security Lock Slot ........................................................A-3
Serial Port .....................................................................A-3
S/PDIF-Out Jack ...........................................................A-4
S-Video-Out Jack ..........................................................A-4
USB 2.0/1.1 Ports .........................................................A-4
Optional Port Replicator Ports and Jacks .....................A-5
DC-In Jack ..................................................... .... .... .......A-5
External Monitor (VGA) Port .......................................A-5
Parallel Port ...................................................................A-5
Serial Port .....................................................................A-5
RJ-45 LAN Jack ............................................................A-5
USB 2.0/1.1 Ports .........................................................A-6
Intel Video Driver Controls
Intel Video Driver Installation ......................................B-1
Dynamic Video Memory Technology ..........................B-2
Intel Graphics Properties ..............................................B-3
Display Devices ............................................................B-5
Attaching Other Displays ..............................................B-6
Display Modes ..............................................................B-7
TV Settings .................................................................B-11
Power Settings ........................................... .... .... .........B-12
XVI
Specifications
Processor .......................................................................C-2
Core Logic ....................................................................C-2
Memory .........................................................................C-2
Security ......................................................................... C-2
BIOS ............................................................................. C-2
LCD .............................................................................. C-2
Video Adapter ...............................................................C-3
Storage .......................................................................... C-3
Audio ............................................................................ C-3
Keyboard & Pointing Device ........................................C-3
Interface ........................................................................ C-4
Card Reader ..................................................................C-4
ExpressCard Slot ..........................................................C-4
Communication ............................................................. C-4
Power Management ......................................................C-4
Power ............................................................................ C-5
Battery ...........................................................................C-5
Environmental Spec ......................................................C-5
Physical Dimensions & Weight .................................... C-5
Optional ........................................................................ C-5
Preface
XVII
Preface
XVIII
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 7-in-1 card reader, ExpressCard/34/54), Function/Hot Keys, TouchPad &
Mouse, Audio & Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Bluetooth and Port Replicator
modules (some of which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the Intel video driver controls.
• Appendix C The computer’s specification.
1
Overview 1 - 1
1
Quick Start Guide
Model & Design Differences
This notebook series includes two different model types (Model A or Model B) based upon their specification
details (see Table 1 - 1 below). The series also includes two different designs which vary slightly in color and
appearance. However both designs incorporate the same features, ports and jacks etc.
Feature Model A Model B
Processors Supported
Battery Types
Intel® Core™ Duo Processor
Intel® Core™ Solo Processor
6 Cell Smart Lithium-Ion Battery Pack,
4400mAH (48.8W)
Table 1 - 1 - Model Differences
See “Processor” on page C - 2 and “Battery” on page C - 5 for full details.
1 - 2 Overview
Intel® Core™ Duo Processor
Intel® Core™ Solo Processor
Intel® Celeron® M Processor
6 Cell Smart Lithium-Ion Battery Pack,
4000mAH (44.4W)
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
Check the light colored
boxes with the mark
above to find detailed information about the computer’s features.
Notes
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1
Overview 1 - 3
1
Quick Start Guide
Not Included
Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Win-
dows XP (Home & Professional Editions) operating system.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed in Table 4 - 1, on page 4 - 6. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already
done that for you); refer to Chapter 4 for installation instructions.
Ports and Jacks
See “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
1 - 4 Overview
System Startup
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any perip herals you want to use with the
notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack at the rear of the
computer, then plug the AC power cord into an outlet, and
connect the AC power cord to the AC/DC adapter (Note: If you
have included the Port Replicator in your purchase option see
page 7 - 13).
5. Raise the lid/LCD to a comfort able vie wing a ngle, an d p ress the
power button to turn the computer “on”.
6. Adjust the LCD panel to a comfortable viewing angle.
7. The LED indicators show the power and battery status of the
computer.
Shutdown
Quick Start Guide
Figure 1 - 1 - AC/DC Adapter In
1
Please note that you should always shut your computer down by choosing the Turn Off Computer command from the
Start menu in Windows. This will help prevent hard disk or system problems.
System Startup 1 - 5
1
Quick Start Guide
System Map: Top View with LCD Panel Open
1. Optional Built-In PC Camera
2. LCD
3. Speakers
4. Power Button
5. Hot Key Buttons
6. Keyboard
7. TouchPad and Buttons
8. Built-In Microphone
9. LED Indicators
9
1
2
3
5
6
7
8
3
9
Figure 1 - 2 - Top View with LCD Panel Open
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission devices aboard aircraft is usually prohibited. Make sure
the module(s) are OFF if
you are using the computer
aboard aircraft.
4
5
Use the key combinations to
toggle power to the WLAN/
Bluetooth modules, and
check the LED indicator
icon to see if the modules
are powered on or not (see
Table 1 - 2, on page 1 - 7/
Table 1 - 4, on page 1 - 9).
1 - 6 System Map: Top View with LCD Panel Open
Quick Start Guide
1
LED Indicators
The LED indicators display helpful information about
the current status of the computer.
Table 1 - 2 - LED Indicators
Icon Color Description
Green Number Lock Activated
Green Caps Lock Activated
Green Scroll Lock Activated
Green The Computer is On
Blinking
Green
Red
The Computer is in Stand by Mode
The AC/DC Adapter is Plugged In
& the Computer is Powered Off
Icon Color Description
Red
Blinking
Red
Green The Battery is Fully Charged
Green Hard Disk Activity
Green
The AC/DC Adapter is Plugged In
& the Battery is Charging
The Battery has Reached Critically
Low Power Status
The WLAN/Bluetooth Module(s) is/
are Powered On
LED Indicators 1 - 7
1
Quick Start Guide
Hot Key Buttons & Keyboard
These buttons give instant access to the default Internet browser and e-mail program, and activates the PC
Camera.
Table 1 - 3 - Hot Key Buttons
Hot Key Function
Activate the BisonCap program/Take Still
Picture (See Page 7 - 8)
Activate the Default Internet Program
Activate the Default E-Mail Browser
Audio Record Start/Stop (See Page 2 - 10)
Camera Zoom-In (See Page 7 - 8)
Camera Zoom-Out (See Page 7 - 8)
The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you
to change operational features instantly (see Figure 1
- 3).
Function Keys
NumLk &
Numeric
Keypad
Fn Key
Figure 1 - 3 - Keyboard
ScrLk Keys
Other Keyboards
If your keyboard is damaged or you just want to make a
change, you can use any standard USB keyboard. The
system will detect and enable it automatically. However
special functions/hot-keys unique to the system’s regular keyboard may not work.
1 - 8 Hot Key Buttons & Keyboard
Quick Start Guide
Function Keys
The function keys (F3 - F12 etc.) will act as hot keys when pressed while the Fn key is held down (see “Func-
tion Keys” on page 2 - 8).
Key Function Key Function
Fn + F3 Mute Toggle Fn + F9 Increase LCD Brightness
Fn + F4 Sleep Toggle Fn + F10 PC Camera Module Power Toggle
Fn + F5 Decrease Audio Volume Fn + F11 Wireless LAN Module Power Toggle
Fn + F6 Increase Audio Volume Fn + F12 Bluetooth Module Power Toggle
Fn + F7 Display Toggle Fn + NumLk Number Lock Toggle
Fn + F8 Decrease LCD Brightness Fn + ScrLk Scroll Lock Toggle
Table 1 - 4 - Function Keys
Special Characters
1
Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboa rd) will
not work. Make sure that NumLk is on.
Function Keys 1 - 9
1
Quick Start Guide
System Map: Front & Rear Views
1. LED Indicators
2. Serial Port
3. Mini-IEEE 1394 Port
4. 1 * USB Port
5. DC-In Jack
6. Battery
3
Figure 1 - 4 - Front & Rear Views
The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices.
1
1
4
6
52
Mini-IEEE 1394
1 - 10 System Map: Front & Rear Views
System Map: Left View
Quick Start Guide
Figure 1 - 5 - Left View
1
1
2
Changing DVD Regional Codes
Go to the Control Panel and double-click System >
Hardware (tab), click Device Manager, then click
the + next to DVD/CD-ROM drives. Double-click on
the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to
bring up the control panel to allow you to adjust the
regional code (see “DVD Regional Codes” on
page 2 - 5).
DVD region detection is device dependent, not OSdependent. You can select your module’s region
code 5 times. The fifth selection is permanent. This
cannot be altered even if you change your operating
system or you use the module in another computer.
1. Security Lock Slot
5
4 637
2. Optical Device Drive Bay
(see page 2 - 3)
3. RJ-11 Modem Jack
4. S/PDIF-Out Jack
5. Microphone-In Jack
6. Headphone-Out Jack
7. Line-In Jack
CD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a
sharpened pencil or similar object that may break and become
lodged in the hole.
Media Warning
Don’t try to remove a floppy disk/CD/DVD while the system is
accessing it. This may cause the system to “crash”.
System Map: Left View 1 - 11
1
Quick Start Guide
System Map: Right View
Figure 1 - 6 - Right View
1. ExpressCard Slot
(see page 2 - 7)
2. 7-in-1 Card Reader
3. 2 * USB 2.0 Ports
4. Vent/Fan Intake
5. RJ-45 LAN Jack
6. 7-Pin S-Video-Out
Jack
7. External Monitor Port
The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro)
MS Duo (requires PC adapter) / Mini SD (requires PC adapter) / RS MMC (requires PC adapter)
The 7-pin S-Video Out Jack requires an adapter cable (7-pin S-Video plug to 4-pin S-Video
jack adapter) in order to connect to a standard S-Video cable.
1
2
3
4
5
3
6
7
7-Pin S-Video-Out Jack
ExpressCard Slot
7-in-1 Card Reader
1 - 12 System Map: Right View
System Map: Bottom View
Quick Start Guide
1
CPU
The CPU is not a user serviceable part. Opening this
compartment, or accessing the CPU in any way,
may violate your warranty.
2
4
1
Figure 1 - 7 - Bottom View
1. Vent/Fan Intake
2. Battery
3. Hard Disk Bay Cover
4. CPU/RAM Bay Cover
3
Overheating
To prevent your computer
from overheating make
sure nothing blocks any
Vent/Fan Intake while the
computer is in use.
1
1
1
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery
at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 9 for full instructions.
System Map: Bottom View 1 - 13
1
Quick Start Guide
Windows XP Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are
accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can cu stomize the look of
the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Click here to toggle Category View
Figure 1 - 8 - Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows XP provides basic controls for many of the features, however many new controls are added (or existing ones are enhanced) when you install the drivers listed
in Table 4 - 1, on page 4 - 6. To see all controls it may be necessary to toggle off Category View.
1 - 14 Windows XP Start Menu & Control Panel
Quick Start Guide
Video Features
Your computer has built-in Intel (Intel 945GM) video. You can switch display devices, and configure display
options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed. For more detailed video information see “Intel Video Driver Controls” on page B - 1.
To access Display Properties in Windows:
1. Click Start, point to Settings and click Control Panel (or just click Control Panel).
2. Double-click Display (icon) - In the Appearances and Themes category.
3. Click Settings (tab) in the Display Properties dialog box.
4. Move the slider to the preferred setting in Screen resolution (Figure 1 - 9 on page 1 - 16).
5. Click the arrow, and scroll to the preferred setting in Color quality (Figure 1 - 9 on page 1 - 16).
6. You can also access Display Properties by right-clicking the desktop and scrolling down and clicking
Properties. Click Settings (tab) and adjust as above.
7. Open the Display Properties control panel, and click Advanced (button) (Figure 1 - 9 on page 1 - 16) to
bring up the Advanced properties tabs.
8. Click the Intel(R) Graphic s Media Ac ce le rat or Dr iver for Mobile tab, and click Graphics Properties (button)
to make any video adjustments you require.
1
2
3
1
Video Features 1 - 15
1
Quick Start Guide
Display & Graphics Properties
1
2
3
Figure 1 - 9 - Display & Graphics Properties
Power Settings
Power Settings in Display Settings can affect display brightness, contrast etc. (see “Power Settings” on page B - 12).
1 - 16 Video Features
Quick Start Guide
Display Devices & Options
Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or
TV as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port, a TV to
the 7-pin S-Video-Out jack.
The following display modes are available (see “Intel Video Driver Controls” on
page B - 1 for details).
Intel Display Mode Description
Single Mode One of the connected displays is used as the display device
Intel(R) Dual Display Clone Mode Both connected displays output the same view and may be configured independently
Extended Desktop Mode Both connected displays are treated as separate devices, and act as a virtual desktop
Table 1 - 5 - Display Options
Intel Display Note
Note that the notebook is the default Primary display device and may not be changed.
1
Video Features 1 - 17
1
Quick Start Guide
Power Management Features
The Power Options control panel icon in Windows (see page 1 - 14) allows you to configure power management
features for your computer. You may conserve power throug h individual components such as the monitor or hard
disk (by means of Power Schemes), or you may use either Stand by or Hibernate mode to conserve power
throughout the system (enable Hibernate support from the control panel tab). Pay attention to the instructions
on battery care in “Battery Information” on page 3 - 9.
Figure 1 - 10 - Power Options
The computer’s power button, sleep button (Fn + F4 key combination), and lid (closing the lid) may be set to
send the computer in to either Stand by or Hibernate mode.
Power Saving and Performance
Power Schemes may have an affect on your computer performance (see “Power Schemes” on page 3 - 4).
1 - 18 Power Management Features
Features & Components
Chapter 2: Features & Components
Overview
Read this chapter to learn more about the following main features and components
of the computer:
•Hard Disk Drive
• Optical (CD/DVD) Device
• 7-in-1 Card Reader
• ExpressCard Slot
• Function Keys
• TouchPad and Buttons/Mouse
• Audio Features
• Adding a Printer
2
Overview 2 - 1
Features & Components
2
Before attempting to access any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the machine is turned off. Also
ensure that all peripheral cables, including
phone lines, are disconnected from the computer.
Power Safety
Hard Disk Drive
The hard disk drive is used to store your data in the computer. The hard disk can be
taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height
of 9.5 mm.
The hard disk is accessible from the bottom of your computer as seen below. For further details see “Upgrading the Hard Disk Drive” on page 6 - 4.
Figure 2 - 1
Hard Disk Location
Hard Disk
2 - 2 Hard Disk Drive
Features & Components
Optical (CD/DVD) Device
There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The
optical device is usually labeled “Drive D:” and may be used as a boot device if
properly set in the BIOS (see “Boot Menu” on page 5 - 11).
Loading Discs
To insert a CD/DVD, press the open button and carefully place a CD/DVD onto
the disc tray with label-side facing up (use just enough force for the disc to click onto
the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you
are ready to start. The busy indicator will light up while data is being accessed,
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole
3
to open the tray.
1
2
2
1
3
Sound Volume
Adjustment
How high the sound volume can be set depends
on the setting of the volume control within Win-
dows. Click the Volume
icon on the taskbar to
check the setting (see
“Audio Features” on
page 2 - 13).
Figure 2 - 2
Optical Device
2
Optical (CD/DVD) Device 2 - 3
Features & Components
2
CD Emergency Eject
If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharpened pencil or similar
object that may break
and become lodged in
the hole.
Disk Eject Warning
Don’t try to remove a
CD/DVD while the system is accessing it. This
may cause the system
to “crash”.
Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.
Note the following:
• Hold the CD or DVD by the edges; do not touch the surface of the disc.
• Use a clean, soft, dry cloth to remove dust or fingerprints.
• Do not write on the surface with a pen.
• Do not attach paper or other materials to the surface of the disc.
• Do not store or place the CD or DVD in high-temperature areas.
• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
• Do not bend the CD or DVD.
• Do not drop or subject the CD or DVD to shock.
Handling CDs or DVDs
2 - 4 Optical (CD/DVD) Device
Features & Components
DVD Regional Codes
To change the DVD regional codes see “Changing DVD Regional Codes” on
page 1 - 11.
.
DVD Regional Coding
Region Geographical Location
1 USA, Canada
2
3
4
5
6China
Western Europe, Japan, South
Africa, Middle East & Egypt
South-East Asia, Taiwan, South
Korea, The Philippines, Indonesia,
Hong Kong
South & Central America, Mexico,
Australia, New Zealand
N Korea, Russia, Eastern Europe,
India & Most of Africa
2
Table 2 - 1
DVD Regional Coding
Figure 2 - 3
DVD Regions
Optical (CD/DVD) Device 2 - 5
Features & Components
2
Card Reader Cover
Make sure you keep the
cover in the card reader
when not in use. This
will help prevent foreign
objects and/or dust getting in to the card reader.
7-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “Card Reader/ExpressCard” on page 4 - 10).
• MMC (MultiMedia Card)
• SD (Secure Digital)
• MS (Memory Stick)
• MS (Memory Stick Pro)
• MS Duo (requires PC adapter*)
• Mini SD (requires PC adapter*)
• RS MMC (requires PC adapter*)
*Note: The PC adapters are usually supplied with these cards.
Figure 2 - 4
Right View
1. Card Reader
1
2 - 6 7-in-1 Card Reader
Features & Components
ExpressCard Slot
The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/
34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC
Cards).
ExpressCard/54 is used for applications which require a larger interface slot, e.g.
CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34. Make sure you install the ExpressCard driver (see “Card Reader/ExpressCard” on page 4 - 10).
Inserting and Removing ExpressCards
• Align the ExpressCard with the slot and push it in until it locks into place.
• To remove an ExpressCard, simply press the card to eject it.
ExpressCard
Slot Cover
Make sure you keep the
cover in the ExpressCard slot when not in
use. This will help prevent foreign objects and/
or dust getting in to the
ExpressCard Slot.
Figure 2 - 5
ExpressCard Slot
2
ExpressCard Slot 2 - 7
Features & Components
2
Application Note
The hot key functions
will only be displayed if
the program is running
(i.e. the icon is displayed in the taskbar). If
you have closed the program you can run it
again from the Start
menu (Start > Pro-
grams > Startup > HotKey Driver) in
Windows.
Function Keys
The function keys (F3 - F12 etc.) will act as hot keys when pressed while the Fn
key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key driver is installed (see “Hot Key” on page 4 -
10). After installing the driver an icon will appear in the taskbar.
Double-click the icon to bring up the configuration menu that allows you to set
the time for the specific menus to be displayed on screen. Click OK to minimize the
program. If you click the close icon , run the program again from the Start menu
in Windows (Start > Programs/All Programs > Startup > HotKey Driver). Press
Fn + Esc to bring up Help menu.
Figure 2 - 6
Hot Key Driver
Configuration &
Help Menu
2 - 8 Function Keys
Features & Components
Fn/Hot Key
Fn + Esc Help & System Info
Fn + F2 TouchPad Toggle
Fn + F3 Mute Toggle
Fn + F5/F6 Volume Decrease/Increase
Fn + F8/F9 Brightness Decrease/Increase
Fn + F10 PC Camera Power Toggle
Fn + F11 WLAN Module Power Toggle
Fn + F12 Bluetooth Module Power Toggle
Activate BisonCap Program/ Take Still Picture
Audio Record Start/Stop (see over)
Function
See Figure 2 - 6 on page 2 - 8
Hot Key Note
The Help menu will display the function key
features, current Battery
Life, Power State and
CPU Temperature information.
Table 2 - 2
Hot Key & Function
Key Combo
Indicators
2
Function Keys 2 - 9
Features & Components
2
The audio record hot key button allows you to record audio from either the builtin microphone, or from a microphone connected to the microphone-in jack. To
record on the computer, setup the audio recording options in Windows as follows
(see Figure 2 - 7 on page 2 - 11).
1. Go to the Start menu and point to Settings (or just click Control Panel) and click
Control Panel, then double-click the Sounds & Audio Devices icon (Sounds,
Speech, and Audio Devices in Category Vi ew).
2. Click Advanced in the Volume > Device volume tab.
3. Click Options and scroll down and click Properties.
4. Select Realtek HD Audio input from the Mixer device menu.
5. Click Mic Volume (check box) if it is not checked, then click OK.
6. Make sure the Select ( check box) in the Recor ding Control p anel, u nder the Mic
Volume section, is checked (boost the volume as high as it will go).
7. Click Advanced (button).
8. Click to put a tick in the 1 Microphone Boost box, and then click Close.
9. Close the Recording Control window, and then click OK.
10. Press the audio record hot key button to begin the recording process (the
record icon
11. Press the audio record hot key button again to stop the recording process (the
record icon will disappear in the top left of the screen).
12. The recorded audio file (in .wav format) will appear in the Shared Documents >
Wav folder in My Computer.
13. Double-click the file to playback the recorded audio.
will flash in the top left of the screen).
Recording Audio
2 - 10 Function Keys
Features & Components
Audio Setup for
Recording
(Windows XP)
2Figure 2 - 7
Function Keys 2 - 11
Features & Components
2
If you are using an external mouse your operating system may be able
to auto-configure your
mouse during its installation or only enable its
basic functions. Be sure
to check the device’s
user documentation for
details.
Mouse Driver
TouchPad and Buttons/Mouse
The TouchPad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The TouchPad buttons function in
much the same way as a two-button mouse.
Configuring the TouchPad and Buttons
Once you have installed the TouchPad driver you can configure the functions by
double-clicking the TouchPad driver icon in the taskbar, or by going to the
Mouse control panel in Windows (Start menu and point to Settings and click Control Panel, then double-click the Mouse icon). In Windows XP the Mouse control
panel is in the Printers and Other Hardware Category.
Figure 2 - 8
Mouse Properties
2 - 12 TouchPad and Buttons/Mouse
Features & Components
Audio Features
You can configure the audio options on your computer from the Sounds and Audio
Devices Windows control panel, or from the Realtek HD Audio Manager
icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration
menus). The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Sound Volume
Adjustment
How high the sound volume can be set depends
on the setting of the volume control within Win-
dows (and the volume
control function keys on
the computer). Click the
Volume icon on the
taskbar to check the setting.
Figure 2 - 9
Realtek Audio
Configuration
Menus
2
Audio Features 2 - 13
Features & Components
2
Double-click the Realtek
HD Audio Manager
icon in the taskbar to
bring up the Realtek
control panel.
Click Audio I/O (tab).
Select 8CH Speaker
from the pull-down
menu.
Click OK to save.
Connect the cables to
the audio jacks as outlined.
8 Channel Sound
Support
If you wish to configure your system for 8 channel sound support, then the following
ports should be used as outputs. Connect the system cables to the following audio
jacks:
• Side Speaker Out - Connect to S/PDIF Out (Black)
• Center/Subwoofer Speaker Out - Connect to Microphone In (Pink)
• Front Speaker Out - Connect to Speaker/Headphone Out (Green)
• Rear Speaker Out - Connect to Line In (Blue)
Figure 2 - 10
8 Channel Sound
Support
8 Channel Sound Support
2 - 14 Audio Features
Features & Components
Adding a Printer
The most commonly used peripheral is a printer. The following conventions will
help you to add a printer; however it is always best to refer to the printer manual for
specific instructions and configuration options.
USB Printer
Most current printers have a USB interface connection. You may use any one of the
ports to connect the printer.
Install Instructions:
1. Set up the printer according to its instruction s (unpacking, p aper tr ay, toner/ink cartridge etc.).
2. Turn ON the computer.
3. Turn ON the printer.
4. Connect the printer’s USB cable to one of the USB ports on the computer.
5. Windows will identify the printer and either load one of its own drivers or ask you
to supply one. Follow the on-screen instructions.
Parallel Printer
This is still a very common type of printer. The install instructions are in the sidebar.
Note: If you have included the Port Replicator in your purchase option, then a parallel port will be available, otherwise you will need to purchase a parallel to USB
converter.
Parallel Printer
After setting up the printer attach the parallel cable to the printer.
Connect the printer’s
parallel cable to the Parallel to USB converter,
and then plug the converter into the USB port.
Turn ON the printer,
then turn ON the computer.
Windows will identify the
printer and either load
one of its own drivers or
ask you to supply one.
Follow the on-screen instructions.
2
Adding a Printer 2 - 15
Features & Components
2
2-16
Power Management
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer uses the ACPI
power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole
system. This chapter covers:
• The Power Sources
• Turning on the Computer
• Power Schemes
• System Power Options
• Configuring the Power Button
• Battery Information
Advanced Configuration and Power Interface
The ACPI interface provides the computer with enhanced power saving techniques
and gives the operating system (OS) direct control over the power and thermal states
of devices and processors. For example, it enables the OS to set devices into lowpower states based on user settings and information from applications. ACPI is fully
supported in Windows XP.
OS Note
Power management
functions will vary
slightly depending on
your operating system.
For more information it
is best to refer to the
user’s manual of your
operating system.
(Note: All pictures
used on the following
pages are from the
Windows XP OS.)
3
Overview 3 - 1
Power Management
The Power Sources
3
Port Replicator
AC/DC Adapter
You will be provided
with a 90W AC/DC
adapter if you purchase
the port replicator option.
If you are using the computer with the Port Replicator, then you must
use the 90W AC/DC
adapter to power the
port replicator and computer (DO NOT USE the
computer’s AC/DC
adapter to power the
Port Replicator). See
“Port Replicator” on
page 7 - 13 for more in-
formation.
The computer can be powered by either an AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1. Attach th e AC/DC adapter to the DC-in jack at the rear of the computer.
2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter (see sidebar if you are using the optional Port Replicator).
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 12).
We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 9.
3 - 2 The Power Sources
Turning on the Computer
Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options in the Windows control panel to configure this feature.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.
Power Button as Stand by or Hibernate Button
If you are using a fully ACPI-compliant OS, (such as Windows XP) you can use the OS’s
“Power Options” control panel to set the power button to send the system into Stand by or
Hibernate mode (see your OS’s documentation, or “Configuring the Po wer Button” on
page 3 - 8 for details).
Power Management
Shutdown
Note that you should always shut your computer down by choosing the
Turn Off Computer
command from the Start
menu in Windows. This
will help prevent hard
disk or system problems.
3
Turning on the Computer 3 - 3
Power Management
Power Schemes
3
Resuming
Operation
Press the Sleep/Resume key combination
(Fn + F4), or power button to resume from Monitor or Hard Disk Stand
by.
Figure 3 - 1
Power Schemes
You can set your computer to conserve power through individual components by
means of Power Schemes. You can also adjust the settings for each scheme to set
the monitor to turn off after a specified time, and the computer's hard disk motor to
turn off if the hard disk drive has not been accessed for a specified period of time (if
the system reads or writes data, the hard disk motor will be turned back on). The
schemes may also be set to set a specified time for the system to enter Stand by or
Hibernate modes (see “System Power Options” on page 3 - 6).
3-4Power Schemes
Each Windows Power Scheme will also adjust the processor performance of your
machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).
Choose the Home/Office Desk scheme for maximum performance when the com-
puter is powered from an AC power source. Choose the Max Battery scheme (bear
in mind that this scheme may slow down the overall performance of the computer in
order to save power) for maximum power saving when the computer is battery (DC
power) powered. Windows will use Portable/Laptop as the default scheme.
Windows will use Portable/Laptop as the default scheme.
Power Management
3
Power Schemes 3 - 5
Power Management
System Power Options
You can use the system power options to stop the computer’s operation and restart
3
where you left off. This system features Stand by and Hibernate sleep mode levels
(Hibernate mode will need to be enabled by clicking the option in the Hibernate
tab in the Power Options control panel - see “Hibernate” on page 3 - 7).
Hibernate Mode vs. Shutdown
Hibernate mode and Shutdown are the same in that the system is off and you need
to press the power button to turn it on. Their main difference is:
When you come back from hibernation, you can return to where you last left off
(what was on your desktop) without reopening the application(s) and file(s) you last
used.
You can use either method depending on your needs.
Stand by Mode vs. Hibernate Mode
If you want to stay away from your work for just a while, you can put the system on
Stand by instead of in hibernation. It takes a longer time to wake up the system from
Hibernate mode than from Stand by mode.
3 - 6 System Power Options
Stand by
Stand by saves the least amount of power, but takes the shortest time to return to full
operation. During Stand by the hard disk is turned off, and the CPU is made to idle
at its slowest speed. All open applications are retained in memory. When you are not
using your computer for a certain length of time, which you specify in the operating
system, it will enter Stand by mode to save power.
Hibernate
Hibernate uses no power and saves all of your information on a part of the HDD before it turns the system off. Although it saves the most power it takes the longest time
to return to full operation. You can set your computer to automatically enter Hibernate mode when the battery power is almost depleted. You will need to enable Hibernate mode from the Hibernate tab in the Power Options control panel. The
system will resume from Hibernate mode by pressing the power button.
Power Management
System Resume
The system can resume
from Stand by mode by:
• Pressing the power
button
• An incoming call
received on the
modem (if enabled)
• Network card activity
(if enabled)
Figure 3 - 2
Enable Hibernation
3
System Power Options 3 - 7
Power Management
Configuring the Power Button
3
Sleep Button
You may also configure
the Sleep/Resume key
combination (Fn + F4)
from the menu illustrated in Figure 3 - 3. In
Windows this is referred to as the Sleep
button.
Figure 3 - 3
Power Options
(Advanced - Power
Buttons)
The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate mode
the LED will be off (battery) or red (AC/DC adapter). If you are in a power saving
mode set to save power through individual components (e.g. hard disk, monitor), the
LED will remain green.
Power Button Sleep/ResumeLid
(Sleep) Button
3 - 8 Configuring the Power Button
Battery Information
Please follow these simple guidelines to get the best use out of your battery.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 12 for instructions on how to do this).
Battery Life
Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached. Power Options (you may
set low battery Alarms and actions, and check the Power Meter from the Power
Options control panel), and settings in the OS will help prolong the battery life if
configured appropriately.
Power Management
Low Battery
Warning
When the battery is critically low, immediately
connect the AC/DC
adapter to the computer
or save your work, otherwise, the unsaved
data will be lost when
the power is depleted.
Figure 3 - 4
Power Options
(Alarm & Power
Meter)
3
Battery Information 3 - 9
Power Management
Battery life may be shortened through improper maintenance. To optimize the life
3
Conserving Battery
Power
To conserve battery power:
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
We recommend that you do not remove the battery yourself. If you need to remove
the battery for any reason, see “Removing the Battery” on page 6 - 3.
Lower the brightness level
of the LCD display. The
system will decrease LCD
brightness slightly to save
power when it is not powered by the AC/DC adapter.
Close modem or communication applications when
they are not being used.
Remove any unused ExpressCards from the computer (ExpressCards
quickly use up battery power even if the system enters
sleep mode).
Disconnect any unnecessary external devices.
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 7 for information on the battery charge status, and to “Battery Information” on page 3 - 9 for more information on how to maintain and properly
recharge the battery pack.)
3 - 10 Battery Information
Proper handling of the Battery Pack
• DO NOT disassemble the battery pack under any circumstances
• DO NOT expose the battery to fire or high temperatures, it may explode
• DO NOT connect the metal terminals (+, -) to each other
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has bee n d roppe d we do
not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire . It is
recommended that you replace your computer battery every two years.
Power Management
3
Battery Information 3 - 11
Power Management
Battery FAQ
3
Danger of explosion if
battery is incorrectly replaced.
Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s instructions.
Caution
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer by yourself even when you see a message that indicates the
battery is critically low, just let the computer use up all of the battery power and shut
down on its own. Disable the Power Options functions i n the Co ntrol Panel, especially any Alarms (unclick the tickboxes - see page 3 - 9) and Schemes (change all
the settings to Never - see page 3 - 4). As the battery nears the end of its life save
and close any critical files.
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.
3 - 12 Battery Information
Chapter 4: Drivers & Utilities
Drivers & Utilities
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some
of the computer’s subsystems. The system takes advantage of some newer hardware components for
which the latest versions of most available operating
systems haven’t built in drivers and utilities. Thus,
some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to
manually install some system-required drivers and
utilities.
What to Install
The Device Drivers & Utilities + User’s Manual CDROM contains the drivers and utilities necessary for
the proper operation of the computer. Table 4 - 1, on
page 4 - 6 lists what you need to install manually ac-
cording to your choice of the operating system, and it
is very important that the drivers are installed in
the order indicated.
Module Driver Installation
The procedures for installing drivers for the PC Camera, Wireless LAN, Bluetooth and Port Replicator
modules are provided in “Modules & Options” on
page 7 - 1. Make sure that the drivers are installed in
the order indicated in Table 4 - 1, on page 4 - 6. Only
install drivers for modules included in your purchase
option.
4
What to Install 4 - 1
Drivers & Utilities
Navigate (Browse..) to D:
You will notice that many of the instructions for driver
4
installation require you to “Navigate (Browse) to D:”.
We assume that you will install all drivers and utilities
from the built-in CD device and it is assigned to “Drive
D:”. In addition, all file extensions can be seen
In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and
some computers have the CD listed under a different
drive letter - e.g. if you have two hard drives (or hard
disk partitions) one may be designated as “Drive C:”
and the other as “Drive D:”. In this case the CD device
may be designated as “Drive E:” - Please make sure
you are actually navigating to the correct drive letter
for the CD device.
When you click the Browse (button) after clicking
Run in the Start menu you will see the “Look in:” dialog box at the top of the Browse window. Click the
scroll button to navigate to My Computer to display
the devices and drive letters.
Figure 4 - 1 - Navigate (Browse..) to..
4 - 2 What to Install
Service Packs
Check the warnings on the following pages regarding
installation of the appropriate Service Pack for your
Windows OS. Make sure you have installed the appropriate Service Pack before installing all the drivers.
Service Pack Installed
To see which Service Pack is currently installed on your
computer go to the General tab of the System control
panel. Right-click the My Computer icon on the desktop
or in the Start menu and select Properties. The Service
Pack currently installed on your system will be listed under the “System:” heading. (If no Service Pack information is listed, then no Service Pack is installed.)
Drivers & Utilities
Windows XP Service Pack 2
Make sure you install Windows XP Service Pack 2 (or
a Windows XP version which includes Service Pack 2)
before installing any drivers. Service Pack 2 includes
support for USB 2.0.
If you have upgraded the system by installing Service
Pack 2 (i.e. your Windows XP version does not include
Service Pack 2) then follow these instructions:
1.Click Start (menu), point to Settings and click Control
Panel (or click Control Panel).
2.Double-click System (icon); System (icon) is in Per-
formance and Maintenance (category).
3.Click the Hardware (tab) > Device Manager (button).
4.Click “+” next to Other Devices (if its sub-items are not
shown).
5.Right-click Universal Serial Bus (USB) Controller
and select Uninstall > OK (if you don’t see the item
then there is no need to take any further action).
6.Restart the computer and it will find the USB 2.0 controller.
4
What to Install 4 - 3
Drivers & Utilities
Authorized Driver Message
If you receive a message telling you that the driver you
are installing is not authorized (Digital Signature Not
Found), just click Yes or Continue Anyway to ignore
the message and continue the installation procedure.
4
You will receive this message in cases where the driver has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.
Version Conflict Message
During driver installation if you encounter any “file
version conflict” message, please click Yes to choose
to keep the existing (newer) version.
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Add/Remove Programs item. If you
see the individual driver listed (if not see below), uninstall it, following the on screen prompts (it may be
necessary to restart the computer). Go to the appropriate section of the manual to complete the update/reinstall procedure for the driver in question.
If the driver is not listed in the Add/Remove Pro-
grams item:
1. Click Start (menu), point to Settings and click Control
Panel (or click Start > Control Panel).
2. Double-click System (icon); System (icon) is in
Performance and Maintenance (category).
3. Click Hardware (tab) > Device Manager (button).
4. Doubl e-click the device you wish to update/reinstall the
driver for (you may need to click “+”).
5. Look for the Update Driver button (check the Driver tab)
and follow the on screen prompts.
4 - 4 What to Install
Drivers & Utilities
Driver Installation
This section covers driver and utility installation instructions for Windows XP Home & Professional editions. Insert the Device Drivers & Utilities + User’s
Manual CD-ROM and click the appropriate driver
name from the from the Driver Installation menu and
follow the instructions to install the driver. Alternatively click Start (or click the Browse CD button) and
navigate (Browse..) to the setup.exe to follow the
manual setup instructions.
Driver Installation Application
1. Check the driver installation order from Table 4 - 1,
on page 4 - 6 (the drivers must be installed in
this order) which is the same as listed in the menu.
2. Double-click the name of the driver you wish to
install.
3. Follow the instructions for each installation
procedure, as listed on the following pages.
4. Make a note of the drivers you have installed.
5. If the computer needs to restart after installing a
driver, you will usually need to click the “Yes/
Finish” button when prompted to do so.
6. Make sure you tick the “Show Install Menu next
time you start Windows when CD is Inserted”
tickbox to come back to the Driver Installation
screen (otherwise click Start (menu) > Run... and
navigate (Browse..) to D:\Autorun.exe and click
OK.
OR
Double-click the My Computer icon, and then
double-click the CD icon.
Figure 4 - 2 - Driver Installation
4
Driver Installation 4 - 5
Drivers & Utilities
New Hardware Found
If you see the message “New Hardware Found”
(Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver
install procedure), click Cancel to close the window,
4
and follow the installation procedure as directed.
WinXP SP2 Driver Page # WinXP SP2 Driver Page #
Install the appropriate Service Pack for WinXP Page 4 - 3 Card Reader/ExpressCard Page 4 - 10
Chipset Page 4 - 7 Hot Key Page 4 - 10
IAA (Intel Application Accelerator)
Required for SATA AHCI Setup Options Only
Video Page 4 - 8 Wireless LAN Page 7 - 10
Audio Page 4 - 8 Bluetooth Page 7 - 11
LAN Page 4 - 8 Port Replicator Serial Port Page 7 - 14
Modem Page 4 - 9 Port Replicator Network (LAN) Port Page 7 - 15
TouchPad Page 4 - 9
Table 4 - 1 - Driver Installation
Service Pack Installation
Make sure you install the appropriate service pack for
your operating system before installing any drivers
(see “Service Packs” on page 4 - 3).
Page 4 - 7 PC Camera Page 7 - 3
4 - 6 Driver Installation
Drivers & Utilities
WinXP Driver Installation Procedure
Chipset
1. Double-click Chipset.
OR
Click Start (menu) > Run... and navigate
(Browse..) to
D:\Drivers\inf_update\infinst_autol.exe and
click OK.
2. Click Next > Yes > Next.
3. Click Finish to restart the computer .
IAA (Intel Application Accelerator)
Note: This driver is only required (and will only appear in the Driver Installation menu) if you have enabled AHCI mode for SATA hard disks - see “Setting
Up AHCI SATA Mode” on page 5 - 6. If you have
not enabled AHCI mode, do not install this driver.
1. Double-click IAA.
OR
Click S tart (menu) > Run... and navigate
(Browse..) to
D:\Drivers\Intel-IAA\Setup.exe and click
OK.
2. Click Yes if asked to replace the current driver
version.
3. Click Next > Next > Yes > Next > Next.
4. Click Finish to restart the computer.
4
Driver Installation 4 - 7
Drivers & Utilities
Video (VGA)
1. Double-click VGA.
OR
Navigate (Browse..) to
4
D:\Drivers\VGA\Setup.exe and click OK.
2. Click Next > Yes.
3. Click Finish to restart the computer .
Audio
1. Double-click Audio.
OR
Navigate (Browse..) to
D:\Drivers\Audio\Setup.exe and click OK.
2. Click Next (click Continue Anyway if asked if
you want to continue at any time).
3. Click Finish to restart the computer .
LAN
1. Double-click Lan.
OR
Click S tart (menu) > Run... and navigate
(Browse...) to D:\Drivers\Lan\Setup.exe and
click OK.
2. Click Next.
3. Click Finish.
4. The network settings can now be configured.
4 - 8 Driver Installation
Drivers & Utilities
Modem
1.
Double-click Modem.
OR
Click Start (menu) > Run... and navigate
(Browse...) to
D:\Drivers\Modem\HXFSetup.exe
D:\Drivers\Modem\Setup.exe
(one of the following)
and click OK.
2. Click OK > OK.
3. The modem is ready for dial-up configuration.
Modem Country Selection
Be sure to check if the modem country selection is appropriate for you (Control Panel > Phone and Modem
Options).
TouchPad
1. Double-click TouchPad.
OR
Click S tart (menu) > Run... and navigate
(Browse..) to
D:\Drivers\Touchpad\SETUP.EXE and click
OK.
2. Click Next > Next (click Continue Anyway if
asked if you want to continue at any time).
3. Click Finish to restart the computer.
4. You may then configure your TouchPad as outlined in “TouchPad and Buttons/Mouse” on
page 2 - 12.
4
Driver Installation 4 - 9
Drivers & Utilities
Card Reader/ExpressCard
1. Double-click
CardReader
OR
Click
Start
(menu) >
(
4
Browse...
) to
Run
D:\Drivers\CardReader\setup.exe
OK
.
2. Click Next.
3. Click Finish to restart the computer .
Hot Key
1.
Double-click
Hot Key.
OR
Click Start (menu) > Run... and navigate
(Browse..) to
D:\Drivers\Hotkey Driver\Setup.EXE and
click OK.
2. Click Next > Install > Finish.
3. Click Finish to restart your computer.
.
...
and navigate
and click
PC Camera
See the introduction in “PC Camera” on page 7 - 2,
and check the installation procedure.
Wireless LAN
See the introduction in “Intel WLAN Module” on
page 7 - 9, and check the installation procedure.
Bluetooth
See the introduction in “Bluetooth Module” on
page 7 - 11, and check the installation procedure.
Port Replicator
See install procedure in “Port Replicator Serial
(COM) Port Driver (WinXP)” on page 7 - 14 and
“Port Replicator Network (LAN) Driver (WinXP)”
on page 7 - 15.
4 - 10 Driver Installation
BIOS Utilities
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Configuration: The Setup utility
If your computer has never been set up, or you are mak ing important chan ges to the
system (e.g. hard disk setup), then you should review this chapter first and note the
original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your
system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service
representative.
BIOS Settings
Warning
Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to Set-
up and restore the Setup Defaults with <F9>.
5
Overview 5 - 1
BIOS Utilities
The Setup Utility
Setup Menus
The Setup menus
shown in this section are
for reference only. Your
5
computer’s menus will
indicate the configuration appropriate for your
model and options.
The Insyde H20 Setup Utility tells the system how to configure itself and manage
basic features and subsystems (e.g. port configuration).
Entering Setup
To enter the Insyde H20 Setup Utility, turn on the computer and quickly press F2
during the startup process.
Setup Screens
The following pages contain additional advice on portions of the Setup Utility.
Along the top of the screen is a menu bar with six (6) menu headings. When you se-
lect a heading, a new screen appears. Scroll through the features listed on each
screen to make changes to the Setup Utility.
Instructions on how to navigate each screen are in the box at the bottom right of the
screen.
The Item Specific Help on the right side of each screen explains the highlighted
item and has useful messages about its options.
5 - 2 The Setup Utility
If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may
execute a command.
Main Menu
n
V
_
_
V
BIOS Utilities
MMaaiin
Main
Language <English>
System Time [16:33:11]
System Date [04:27:2006]
Advanced Security Power Boot Exit
InsydeH20 Setup Utility
Select the current
default language used
by the EFI.
+- Select Boot Device
<> Select Screen
Select Item
Enter Select
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
SubMenu
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you
can change the date and time settings in your operating system, you will also change
these settings. Some applications may also alter data files to reflect these changes.
Figure 5 - 1
Main Menu
5
Main Menu 5 - 3
BIOS Utilities
Advanced Menu
Figure 5 - 2
Advanced Menu
5
Main Advanced Security Power Boot Exit
Boot Configuration
IDE Configuration
Video Configuration
Advanced
InsydeH20 Setup Utility
Configures Boot
Settings.
+- Select Boot Device
<> Select Screen
Select Item
Enter Select
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
SubMenu
The sub-menus in the Advanced menu allow you to configure advanced options for
various hardware features.
5 - 4 Advanced Menu
Boot Configuration (Advanced Menu)
Use this menu to configure the Number Lock mode at startup (boot).
BIOS Utilities
IDE Configuration (Advanced Menu)
Configure either a CD Device or HDD on the computer’s IDE Channel/SATA port/
PATA port from this menu.
SATA Configure as > IDE Configuration (Advanced Menu)
You can use this menu to set the options for your hard disk. Only make changes if
you are sure of what you are doing (see overleaf).
• AHCI (Advanced Host Controller Interface) Mode - This mode enables
advanced serial ATA features, such as Native Command Queuing, to increase
hard disk storage performance (see sidebar).
• Legacy Mode - This mode is the most compatible mode, and can be used for
operating systems such as Linux etc.
Video Configuration > IGD - DVMT Size: (Advanced Menu)
Select the memory size to be used by Intel® Dynamic Video Memory Technology
3.0. The default size is 128MB (see “Dynamic Video Memory Technology” on
page B - 2).
AHCI Mode
If you want to use AHCI
mode, you must enable
this mode before installing your operating system.
If you currently use Leg-
acy mode, and wish to
change to AHCI mode,
you will need to reinstall
the operating system.
5
Advanced Menu 5 - 5
BIOS Utilities
Setting Up AHCI SATA Mode
Before setting up your Serial ATA hard disk in AHCI mode you will need to prepare
the following:
1. An operable computer with a floppy drive, running the Windows XP OS.
2. The Device Drivers & Utilities + User’s Manual CD-ROM.
3. An external USB floppy disk drive.
4. A prepared formatted blank 3.5" 1.44MB floppy diskette.
5
AHCI Setup Procedure
1. Go to the operable computer r unning Windows XP and insert a prepared formatted blank 3.5" 1.44MB floppy diskette.
2. Insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD
drive of the operable computer.
3. Click Start (menu) > Run... and navigate (Browse..) to
D:\Drivers\f6flpy\f6flpy32\F6flpy32.exe and click OK.
4. Make sure the
OK.
5. A SATA AHCI driver diskette will now be created for you.
6. Remove the SATA AHCI driver diskette.
7. Start-up your notebook computer and press <F2> to enter the BIOS.
8. Enable the AHCI option from the Advanced > IDE Configuration > SATA
Configure as menu.
9. Set the CD-ROM Drive as the first device in the boot order from the Boot Device
menu.
formatted blank 3.5" 1.44MB floppy diskette is inserted, and then click
5 - 6 Advanced Menu
10. Insert the Microsoft Windows OS CD into the CD/DVD drive of the notebook
computer, and attach the external USB floppy disk drive to one of the notebook
computer’s USB ports.
11. Select Exit Saving Changes from the Exit menu and click OK to exit the BIOS
and reboot the computer.
12. Press a key when you see the message "Press any key to boot from CD".
13. Press the F6 key when you see the message “Press F6 if you need to install
third party SCSI or RAID driver”.
14. When the Windows Setup menu appears (Windows will load a number of files
before the Setup menu appears), press the <S> key to "Specify Additional
Device".
15. Insert the SATA AHCI driver diskette into the external USB floppy drive.
16. Use the arrow keys to scroll down and select Intel(R) 82801GBM SATA AHCI
Controller (Mobile ICH7M), and press Enter (see below).
BIOS Utilities
5
Intel(R) 82801GR/GH SATA RAID Controller (Desktop ICH7R/DH)
Intel(R) 82801GR/GH SATA AHCI Controller (Desktop ICH7R/DH)
Intel(R) 82801GBM SATA AHCI Controller (Mobile ICH7M)
Intel(R) 82801FR SATA RAID Controller (Desktop ICH6R)
17. The system will now read from the floppy disk drive and then return to the
Windows Setup menu.
18. Press Enter to continue installing the operating system as normal (see your
Windows documentation if you need help on installing the Windows OS).
19. Install the Windows drivers as per Table 4 - 1, on page 4 - 6.
20. Make sure you install the IAA driver after installing the Chipset driver.
Figure 5 - 3
SATA AHCI
Controller - Mobile
ICH7M
Advanced Menu 5 - 7
BIOS Utilities
w
w
Security Menu
Security Menu
Main Advanced Security Power Boot Exit
The changes you make
here affect the access to
the Setup utility itself,
5
machine as it boots up
and also access to your
Set Supervisor Password
Set User Password
after you turn it on.
These settings do not
affect your machine or
network passwords
which will be set in your
software OS.
Figure 5 - 4
Security Menu
Set Supervisor Password (Security Menu)
You can set a password for access to the Setup utility. This will not affect access to
the computer OS (only the Setup utility).
Security
InsydeH20 Setup Utility
Install or Change the
password.
+- Select Boot Device
<> Select Screen
Select Item
Enter Select
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
SubMenu
5 - 8 Security Menu
Set User Password (Security Menu)
You can set a password for user mode access to the Setup utility. This will not affect
access to the computer OS (only the Setup utility). Many menu items in the Setup
utility cannot be modified in user mode. You can only set the user password after
you have set the supervisor password.
Note: To clear existing passwords press Enter and type the existing password, then
press Enter for the new password (without typing any password entry) and Enter
again to confirm the password clearance.
BIOS Utilities
Password Warning
If you set a boot password (Password on boot
is “Enabled“), NEVER
forget your password.
5
The consequences of
this could be serious. If
you cannot remember
your boot password you
must contact your vendor and you may lose all
of the information on
your hard disk.
Security Menu 5 - 9
BIOS Utilities
Power Menu
CST Support for
WinXP with Service
Pack 1
If you wish to install Win-
5
dows XP with Service
Pack 1, then disable
CST Support from this
menu before installing
the operating system.
Figure 5 - 5
Power Menu
Main Advanced Security Power Boot Exit
Advanced CPU Control
Advanced CPU Control (Power Menu)
The sub-menu here control allows you to Enable/Disable support for CST.
InsydeH20 Setup Utility
Power
These items control
various CPU parameters.
+- Select Boot Device
<> Select Screen
Select Item
Enter Select
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
SubMenu
5-10Power Menu
Boot Menu
Main Advanced Security Power Boot Exit
PXE Boot to LAN <Disabled>
FUJITSU MHV2040BH
PHILIPS CD-RW/DVD-ROM SCB5265
When you turn the computer on it will look for an operating system (e.g. WindowsXP) from the devices listed in this menu, and in this priority order. If it cannot
find the operating system on that device, it will try to load it from the next device in
the order specified in the Boot priority order. Item specific help on the right is
available to help you move devices up and down the order.
InsydeH20 Setup Utility
Boot
Disables or enables PXE
boot to LAN.
+- Select Boot Device
<> Select Screen
Select Item
Enter Select
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
SubMenu
BIOS Utilities
Boot Sequence
Order
To move device names
up and down the boot
sequence order, select
the device name and
use the <+> and <->
keys to move the device
up or down the order.
Save the settings and
exit the BIOS.
Figure 5 - 6
Boot Menu
5
Boot Menu 5 - 11
BIOS Utilities
Exit Menu
Figure 5 - 7
Exit Menu
Main Advanced Security Power Boot Exit
Exit Saving Changes
Exit Discarding Changes
Load Optimal Defaults
Discard Changes
5
Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any
changes you have made to the Setup. You can also choose to restore the original Set-
up defaults that will return the Setup to its original state, and erase any previous
changes you have made in a previous session.
InsydeH20 Setup Utility
Exit
Exit system setup and
save your changes.
+- Select Boot Device
<> Select Screen
Select Item
Enter Select
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
SubMenu
5 - 12 Exit Menu
Upgrading The Computer
Chapter 6: Upgrading The Computer
Overview
This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you will need:
• A small crosshead or Phillips screwdriver
• A small regular slotted (flathead) screwdriver
• An antistatic wrist strap
Before working with the internal components you will need to wear an antistatic
wrist strap to ground yourself because static electricity may damage the components.
The chapter includes:
• Removing the Battery
• Upgrading the Hard Disk Drive
• Upgrading the Optical (CD/DVD) Device
• Upgrading the System Memory (RAM)
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
6
Please make sure that you review each procedure before you perform it.
Overview 6 - 1
Upgrading The Computer
When Not to Upgrade
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnect-
6
ed all peripherals and
cables (including telephone lines). It is advisable to also remove your
battery in order to prevent accidentally turning
the machine on.
These procedures involve opening the system’s case, adding and sometimes replacing parts.
You should not perform any of these upgrades if:
• Your system is still under warranty or a service contract
• You don’t have all the necessary equipment
• You’re not in the correct environment
• You doubt your abilities
Under any of these conditions, contact your service representative to purchase or replace the component(s).
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember
to replace the cover(s) and screw(s) before turning the computer on.
6 - 2 Overview
Upgrading The Computer
Removing the Battery
If you are confident in undertaking upgrade procedures yourself, for safety reasons
it is best to remove the battery.
1. Turn the computer off, and turn it over.
2. Slide the latch in the direction of the arrow.
3. Slide the latch in the direction of the arrow, and hold it in place.
4. Slide the battery out in the direction of the arrow .
1
1
2
3
2
3
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
6
Figure 6 - 1
Battery Removal
Removing the Battery 6 - 3
Upgrading The Computer
Upgrading the Hard Disk Drive
HDD System
Warning
New HDD’s are blank. Before you begin make sure:
You have backed up any
data you want to keep from
your old HDD.
6
You have all the CD-ROMs
and FDDs required to install your operating system
and programs.
If you have access to the internet, download the latest
application and hardware
driver updates for the operating system you plan to install. Copy these to a
removable medium.
Figure 6 - 2
Hard Disk Bay &
Screw
The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard
disk drives with a height of 9.5mm (h) (see “Storage” on page C - 3). Follow your
operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in “Driver Installation” on page 4 - 5), when setting up a new hard
disk.
1. Turn off the computer, and turn it over and remove the batt er y.
2. Locate the hard disk bay cover and remove screws - .
3. Remove the hard disk bay cover .
4
1
3
4
1
32
6 - 4 Upgrading the Hard Disk Drive
Upgrading The Computer
4. Slide the hard disk of arrow .
5. Lift the hard disk up in the direction of arrow .
6. Reverse the process to install a new hard disk drive.
5
6
5
Figure 6 - 3
HDD Removal
6
6
Upgrading the Hard Disk Drive 6 - 5
Upgrading The Computer
Upgrading the Optical (CD/DVD) Device
1. Turn off the computer, and turn it over and remove the batt er y.
3
2. Locate the hard disk bay cover and remove screws - .
3. Remove the hard disk bay cover
4. Remove the screw at point , and use a screwdriver to carefully push out the
optical device at point .
5. Reverse the process to install the new device.
6
4
.
5
6
1
4
Figure 6 - 4
Removing the CD/
DVD Device
1
5
6
6 - 6 Upgrading the Optical (CD/DVD) Device
32
Upgrading The Computer
Upgrading the System Memory (RAM)
The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for
details of supported module types).
The total memory size is automatically detected by the POST routine once you turn
on your computer.
1. Turn off the computer, and turn it over and remove the battery.
2. Locate the CPU/RAM bay cover and remove screws
1
7
2
3 4
1 7
- .
6
Figure 6 - 5
CPU/RAM Bay
Screws
6
5
Upgrading the System Memory (RAM) 6 - 7
Upgrading The Computer
3. Remove the bay cover .
8
Figure 6 - 6
CPU/RAM Bay
Cover Removed
8
6
Contact Warning
Be careful not to touch
the metal pins on the
module’s connecting
edge. Even the cleanest
hands have oils which
can attract particles, and
degrade the module’s
performance.
Figure 6 - 7
RAM Module
Release Latches
4. Gently pull the two release latches on the sides of the memory socket in the
direction indicated by the arrows ( &
9 10
) in Figure 6 - 7.
9
9
10
10
6 - 8 Upgrading the System Memory (RAM)
Upgrading The Computer
5. The RAM module will pop-up, and you can remove it.
6. Pull the latches to release the second module if necessary.
7. Insert a new module holding it at about a 30° angle and fit the connectors firmly
into the memory slot.
8. The module’s pin alignment will allow it to only fit one way. Make sure the module
is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit
without much pressure.
9. Press the module in and down towards th e mainboard until the slot levers click into
place to secure the module.
10. Replace the bay cover and screws.
11. Restart the computer to allow the BIOS to register the new memory configuration
as it starts up.
11
1111
11
Figure 6 - 8
RAM Module
Removal
6
Upgrading the System Memory (RAM) 6 - 9
Upgrading The Computer
Upgrading the Processor
Warranty
The CPU is not a user
serviceable part. Opening this compartment, or
accessing the CPU in
any way, may violate
your warranty.
6
Unauthorized tampering
with the HDD may also
violate your warranty.
If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may
damage the processor or mainboard.
6 - 10 Upgrading the Processor
Modules & Options
Chapter 7: Modules & Options
Overview
This chapter contains information on the following modules, which may come with
your computer, depending on the configuration purchased. If you are unsure please
contact your service representative.
•PC Camera
• Intel WLAN Module
• Bluetooth Module
• Port Replicator
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission
devices aboard aircraft
is usually prohibited.
Make sure the module(s) are OFF if you are
using the computer
aboard aircraft.
7
Overview 7 - 1
Modules & Options
PC Camera
Taking Still Pictures
Double-click the
Computer
desktop, or go the
menu and point to
Computer
.
Double-click the
Cam, NB Pro
icon on the
, then click it.
icon.
7
Take a new picture
Click
in the
box.
You can use the application hot key to take
still pictures if you have
installed the hot key driver. (See
Hot Keys” on page 7 8
Camera Tasks
“PC Camera
.)
My
Start
My
Bison-
Before installing the PC Camera driver, make sure that the optional PC Camera is
on. Use the Fn + F10 key combination (see “Function Keys” on page 1 - 9) to toggle power to the PC Camera module. Make sure you install the drivers in the order
indicated in Table 4 - 1, on page 4 - 6.
After installing the driver you can run the application software by going to the
BisonCam item in the Start > Programs/All Programs menu and selecting the
BisonCap program.
Latest PC Camera Driver Information
Check the PC Camera CD, and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here.
7 - 2 PC Camera
Loading...