CHIEF KTA320, KTA325 User Manual
INSTALLATION INSTRUCTIONS
KTA-220/225
KTA-320/325
Horizontal Array Pole Clamp
Models: KTA-220/225 and KTA-320/325
The KTA-220/225 and KTA-320/325 pivot arrays allow
horizontal (yaw), vertical (pitch), and roll display
adjustment. The pitch adjustment range is 30° (15° up /
15° down).
The KTA is designed to mount two or three 17" displays.
The KT A accommodates standard VESA® 75mm/100mm
compliant displays.
BEFORE YOU BEGIN
CAUTION: To prevent damage to your display, which could affect or void the Factory warranty, thoroughly study all
instructions and illustrations before you begin to install the mount. Pay particular attention to the "Important Warnings
and Cautions" on Page 2.
CAUTION: The combined weight of the displays installed must not exceed 70 lbs (31.8 kg) for the KTA-220 and
KT A-225 and 90lbs (40.8 kg) fo r the KTA-320 and KTA-325, th e maximum load cap acity of the mount s. The weight of
each individual display must not exceed 35 lbs (15.9 kg) for the KTA-220 and KTA-225 or 30 lbs (13.6 kg) for the
KTA-320 and KTA-325.
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE 700
SAVAGE, MINNESOTA 55378 USA
8832-000141 Rev E
©2008 Chief Manufacturing
www.chiefmfg.com
11/08
Models: KTA-220/225 and KTA-320/325 Installation Instructions
IMPORTANT WARNINGS AND CAUTIONS!................... 2
TOOLS REQUIRED FOR INSTALLATION........................3
Parts...................................................................................3
INSTALLATION................................................................. 4
Display Installation .........................................................4
Attach Centris Head to Flush Mount Display.............. 4
Attach Centris Head to Recessed Mount Display.......5
ADJUSTMENTS............................................................. 6
Array Adjustment..................................................... ....... 6
Display Adjustment.........................................................6
Display Horizontal Position Adjustment......................6
Display Pitch, Roll, and Yaw Adjustment.................... 6
• IMPORTANT WARNINGS AND CAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: RISK OF ELECTRIC SHOCK ! Using the wrong screws could result in severe personal injur y or damage
to your display. If your display uses a longer screw size than those included in the kit, DO NOT use the screws
provided with the kit. Use the screws provided with your display or contact the manufacturer.
WARNING: Improper installation can result in serious personal injury! Make sure that the mounting surface can
support a redundant weight factor five times the total weight of the equipment. If not, reinforce the mounting surface
structural members before installing the mount.
WARNING: Be aware of the potential for personal injury or damage to the unit if it is not adequately mounted.
WARNING: The installer is responsible for verifying that the mounting surface to which the KTA is anchored will
safely support the combined load of all attached components or other equipment.
WARNING: Watch for pinch points. Do not put your fingers between movable parts.
WARNING: Make sure the mount is correctly oriented.
WARNING: The combined weight of the displays installed must not exceed 70 lbs (31.8 kg) for the KTA-220 and
KT A-225 and 90lbs (40.8 kg) for the KTA-320 and KTA-325, th e maximum load cap acity of t he mount s. The weight of
each individual display must not exceed 35 lbs (15.9 kg) for the KTA-220 and KTA-225 or 30 lbs (13.6 kg) for the
KTA-320 and KTA-325.
CAUTION: Check the unit for shipping damage before you begin the installation.
CONTENTS
2
Installation Instructions Models: KTA-220/225 and KTA-320/325
Table 1: Parts
ITEM DESCRIPTION QTY*
10 ARRAY ASSEMBLY, KTA-220/225 1
20 ARRAY ASSEMBLY, KTA-320/325 1
30 SCREW, Phillips Pan Head, M4 x 12mm 4
40 SCREW, Phillips Pan Head, M4 x 20mm 4
50 SCREW, Phillips Pan Head, M4 x 30mm 4
60 SPACER, Nylon, 3/8" (used with item 40) 4
70 SPACER, Nylon, 3/4" (used with item 50) 4
80 KEY, Hex, 5/32" 1
90 BRACKET, Pole Clamp, Back 1
100 SCREW, Button Head, 1/4-20 x3/4" 2
110 WASHER, Flat. 1/4" 2
* Quantity varies depending upon the number of displays being
mounted.
10
20
30 50
60
70
80
40
110
90
100
TOOLS REQUIRED FOR INSTALLATION
• Phillips screwdriver
•3/16" Hex Key
•5/32" Hex Key
NOTE: Other tools may be required de pe ndin g on you r
method of installation.
Parts
Unpack carton and verify kit contents . Read installation
instructions completely. If any listed parts are missing,
contact Chief Customer Service.
Figure 1: PARTS
3
Loading...