Page 1
INSTALLATION INSTRUCTIONS
VESA Bracket for J-Series
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
JSBV
Page 2
Installation Instructions JSBV
3.94
100
15.75
400
3.94
100
7.87
200
11.81
300
7.87
200
7.87
200
ALL MEASUREMENTS ARE IN
THE FOLLOWING FORMAT:
[MILLIMETERS]
INCHES
DISCLAIMER
Milestone AV Technologies, Inc., and its affiliated corporations
and subsidiaries, intend to make this manual accurate and
complete. However, Milestone makes no claim that the
information contained herein covers all details, conditions or
variations, nor does it provide for every possible contingency in
connection with the installation or use of this product. The
information containe d in this document is subject to change
without notice or obligation of any kind. Milestone makes no
representation of warranty, expressed or implied, regarding the
information contained herein. Milestone assumes no
responsibility for accuracy, completeness or sufficiency of the
information contained in this document.
Chief® and Centris™ are registered trademarks of Milestone
AV Technologies. All rights reserved.
WARNING:
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING:
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
Failure to read, thoroughly understand, and
Failure to provide adequate structural strength
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING:
serious injury or death if you do not follow the instructions.
CAUTION:
damage or destruction of equipment if you do not follow the
corresponding instructions.
A WARNING alerts you to the possibility of
A CAUTION alerts you to the possibility of
DIMENSIONS
WARNING:
Exceeding the weight capacity of the mount
can result in serious personal injury or damage to equipment!
It is the installer’s responsibility to make sure the combined
weight of the mount and all attached components does not
exceed 75 lbs (34.02 kg).
2
Page 3
Installation Instructions JSBV
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
LEGEND
3
Page 4
JSBV Installation Instructions
#2
3/16"
(Provided)
5/32"
(Provided)
A (1)
BAG B
BAG C
BAG D
BAG E
B (4)
M4 x 8mm
C (4)
M4 x 12mm
D (6)
M4 x 16mm
E (4)
M4 x 20mm
F (8)
M6 x 20mm
G (4)
M6 x 30mm
H (4)
M6 x 45mm
J (8)
.740x.250x.250
K (6)
.194x.625x.125
L (1)
3/16"
M (1)
5/32"
N (8)
M5 x 20mm
P (4)
M5 x 30mm
Q (4)
M5 x 45mm
BAG A
TOOLS REQUIRED FOR INSTALLATION
PARTS
4
Page 5
Installation Instructions JSBV
(J) or (K) if needed
[from hardware bag C]
(A)
(D through H,
N through Q)
2
2
(A)
(C-H, N-Q)
(B) x 4
2
(A)
INSTALLATION
WARNING:
MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute
hardware. Only use hardware provided or specified by
manufacturer.
1. Place JSBV interface bracket over the mounting holes on
the back of the display, making sure to center the bracket as
much as possible.
WARNING:
DAMAGE TO EQUIPMENT OR TO MOUNT FALLING
CAUSING SERIOUS PERSONAL INJURY ! Use proper size
and length hardware depending on display.
NOTE:
NOTE:
2. Using the same number of spacers (if required) and screws
Use screws from hardware bags A, B, or E, dependent
upon whether or not spacers are required.
as holes in the display back, attach JSBV interface bracket
to the display back. (See Figure 1)
IMPROPER INSTALLATION CAN LEAD TO
IMPROPER INSTALLATION CAN LEAD TO
Use spacers from hardware bag C if the display
mounting holes are recessed, or if there is some
protrusion or bowing in the back of display.
2. Attach Interface Bracket (A) to display using appropriate
screws (C-H, N-Q). (See Figure 2)
NOTE:
3. Tighten all screws.
If the display has a recessed mounting surface,
spacers (K or J) between the display and Interface
Bracket (A) may be required.
Figure 2
Attach Display to Mount
1. Start two M4 x 8mm Phillips pan head screws (B) into top
mounting holes on interface bracket (A). (See Figure 3)
2. Align two screws in interface bracket (A) with upper
mounting holes in Centris cup and lower display until
screws are seated in lower area of teardrop mounting
holes. (See Figure 3)
Figure 1
CAUTION:
each screw carefully, but do NOT overtighten.
PREVENT EQUIPMENT DAMAMGE! Tighten
Attach Interface Bracket to Display
1. Lay display face down on a clean and dry flat surface.
Figure 3
3. Hold display so that display back is against Centris cup and
install two M4 x 8mm Phillips pan head machine screws (B)
5
Page 6
JSBV Installation Instructions
(B) x 4
3
(A)
through lower mounting holes in Centris cup and into lower
mounting holes in interface bracket (A). (See Figure 4)
Figure 4
4. Complete installation of mount to display, following
instructions included with the mount.
6
Page 7
Installation Instructions JSBV
7
Page 8
JSBV Installation Instructions
Chief Manufacturing, a division of
Milestone AV Technologies
8832-000250
©2008 Milestone AV Technologies
www.chiefmfg.com
06/08
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P +86-755-8996 92 26
F +86-755-8996 9217
Loading...