Page 1
Fl
l
INSTALLATION INSTRUCTIONS
at Pane
Dual Swing Arm Wall Mount
FWD-111
The FWD-111 dual arm wall mount was designed to support
flat panel displays with 10” to 30” diagonal screens and
weighing a maximum of 40 lbs (18.1 kg).
At only 2.15” deep in the closed position, the mount allows
side-to-side pivot adjustment up to 180 degrees in the closed
and the fully extended position. A display can be extended
14.2” from the wall and pivot 360 degrees.
The FWD-111 fits the following VESA® patterns:
• 75mm/75mm (using the Centris™ mount)
• 100mm/100mm (using the Centris mount)
• 200mm/100mm (using the interface bracket with the
Centris mount)
BEFORE YOU BEGIN
• Caution: To prevent damage to the FWD-111, which could affect or void the Factory warranty, and to the
equipment that will be attached to it, thoroughly study all instructions and illustrations before you begin
the installation. Pay particular attention to the “Important Warnings and Cautions” on Page 2.
• The maximum weight to be installed on the FWD-111 wall mount is 40 pounds (18.1 kg).
• The FWD-111 wall mount is designed to be installed using wall studs or supporting framework. The structure to
which the FWD-1 11 wall mount is anchored must be capable of supporting five times the total weight of the mount
and all attached equipment.
• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480.
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY STE. 700
SAVAGE, MINNESOTA 55378 USA
PART NO. 8832-000132
©2005 Chief Manufacturing
www.chiefmfg.com
10/05
Page 2
Installation Instructions FWD-111
IMPORTANT WARNINGS AND CAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the cor-
responding instructions.
• WARNING: Improper installation can result in serious personal injury! Make sure that the structural members can
support a redundant weight factor five times the total weight of the equipment. If not, reinforce the
structure before installing the FWD-111.
• WARNING: Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.
• WARNING: The installer is responsible for verifying that the wall to which the FWD-111 is anchored will safely sup-
port the combined load of all attached components or other equipment.
• WARNING: The weight of the display placed on the FWD-111 must not exceed 40 lbs. (18.1 kg), the maximum load
capacity of the FWD-111.
• WARNING: Watch for pinch points. Do not put your fingers between movable parts.
• WARNING: Make sure the mount and brackets are correctly oriented.
• CAUTION: Check the unit for shipping damage before you begin the installation.
DRAWING
309.314
12.18
100
3.94
119.050
4.69
75
2.95
54.760
2.16
(COLL APS ED)
2
404.545
15.93
(E XTENDE D )
75
2.95
100
3.94
Page 3
Installation Instructions FWD-111
CONTENTS
IMPORTANT WARNINGS AND CAUTIONS ...... ...... . 2
DRAWINGS ............................................................... 2
TOOLS REQUIRED FOR INSTALLATION ................ 3
INSPECT THE UNIT BEFORE INSTALLING ............ 3
INTRODUCTION ....................................................... 3
COMPONENTS ......................................................... 4
PARTS ....................................................................... 5
INSTALLATION ......................................................... 6
Secure Wall Bracket .............................................. 6
Tighten Centris Adjustment Screw......................... 6
Install FWD-111 on Wall Bracket........................... 7
Flush Mount – 75mm/100mm Pattern.................... 8
Recessed Mount – 75mm/100mm Pattern ............ 8
200mm/100mm Pattern ................. .... ... ... ... .... ... ... . 9
Installing Non-VESA Compliant Mounts ................ 9
CABLE MANAGEMENT ............................................ 10
ADJUSTMENTS ........................................................ 10
TOOLS REQUIRED FOR
INSTALLATION
• Electric drill and bit set
• Phillips Screwdriver
• Level
NOTE: Other tools may be required depending on the
mounting surface and method of installation.
INSPECT THE UNIT BEFORE
INSTALLING
WARNING: Watch for pinch points. Do not put your fin-
gers between movable parts.
1. Carefully inspect the FWD-111 for shipping damage. If
any damage is apparent, call your carrier claims agent and
do not continue with the installation until the carrier has
reviewed the damage.
NOTE: Read all instructions before starting installation.
2. Lay out components to ensure you have all the required
parts before proceeding (refer to Figure 1 on page 4).
Rotational Tilt, Pitch, and Roll Adjustment............. 10
Lateral tension Adjustment .................................... 10
INTRODUCTION
Depending on the size of your display, select one of the following FWD-111 installation configurations:
• Install your display using the “Flush Mount – 75mm/
100mm Pattern” on page 8.
• Install your display using the “Recessed Mount – 75mm/
100mm Pattern” on page 8.
• Install your display using the “200mm/100mm Pattern” on
page 9.
• Install your display using the “Installing Non-VESA Compliant Mounts” on page 9.
3
Page 4
Installation Instructions FWD-111
COMPONENTS
10
80
70
90
30
120
100
40
20
50
Figure 1. FWD-111 Components
60
160
110
150
140
130
4
Page 5
Installation Instructions FWD-111
PARTS
Table 1: Parts
ITEM
NUMBER DESCRIPTION QTY NOTES
10 WALL MOUNT 1
20 PHILLIPS PAN HEAD MACHINE SCREW, M4 x 12mm 4 FLUSH MOUNT
30 PHILLIPS PAN HEAD MACHINE SCREW, M4 x 30mm
(USE WITH 40)*
40 3/4” NYLON SPACER 4
50 PHILLIPS PAN HEAD MACHINE SCREW, M4 x 20mm
(USE WITH 60)**
60 3/8” NYLON SPACER 4
70 200mm x 100mm INTERFACE BRACKET
(USE WITH 80 AND 90)***
90 PHILLIPS PAN HEAD MACHINE SCREW, M4 x 5mm 4
100 PHILLIPS PAN WOOD SCREW, #10 x 2-1/2” 2
110 WASHER 2
120 WALL BRACKET 1
130 COVER PLATE 2 CABLE
140 COVER PLATE FLAT HEAD SCREW 4
150 3/16” HEX KEY 1 For Adjustments
160 5/32” HEX KEY 1 For Set Screw
4
4
1
RECESSED
MOUNT
200mm x 100mm
Mtg. Hole Pattern80 PHILLIPS FLAT HEAD MACHINE SCREW, M4 x 12mm 6
SINGLE STUD
MOUNTED
MANAGEMENT
NOTES:
• *Use M4 x 30mm screws (30) with spacers (40) for recessed applications.
• **Use M4 x 20mm screws (50) with spacers (60) for recessed applications.
• ***Use the six flat head screws (80) to mount the 200mm x 100mm interface bracket (70).
Use four M4 x 5mm screws (90) to mount the Centris bracket to the 200mm x 100mm
interface bracket (70).
5
Page 6
Installation Instructions FWD-111
INSTALLATION
Secure Wall Bracket
WARNING: It is the responsibility of the installer to ver-
ify that the surface to which the FWD-111 is
anchored will safely support the combined
load of all attached components and equipment.
Install the FWD-111 as follows:
1. Determine the exact mounting location prior to install a tion, considering the unit’s swing and extension radius.
WARNING: Improper installation can result in serious
personal injury! Make sure that the structural members can support a redundant
weight factor five times the total weight of
the equipment. If not, reinforce the structure before installing the FWD-111.
2. Using the wall bracket (120) as a template, drill two 3/32”
pilot holes to a minimum depth of 1-1/2”.
3. Using two #10 x 2-1/2” wood screws (100) and two washers (110), secure the wall bracket (120). See Figure 2.
4. Check mount to insure it is level and adjust to level if necessary.
120
100
Figure 2. Secure Wall Bracket
110
5. Make sure no power is supplied to the display before
attempting to mount the display.
6. Remove four screws (supplied) from the back of your display (see Figure 3).
Tighten Centris Adjustment Screw
1. Check adjustment screw on the Centris mount interface to
ensure that the screw is tight. See Figure 4.
2. If needed, use a Phillips screwdriver to tighten the screw.
Figure 3. Remove Screws
6
Figure 4. Tighten Centris Adjustment Screw
Page 7
Installation Instructions FWD-111
Install FWD-111 on Wall Bracket
1. Install the FWD-111 on the wall bracket by placing the top
of the FWD-111 over the top of the wall bracket and pushing the bottom of the FWD-111 over the bottom of the
wall bracket (see Figure 5).
2. Using the 5/32” hex wrench (160), secure the FWD-111 to
the wall bracket by tightening the set screw (see Figure 6).
NOTE: Refer to the “INTRODUCTION” on pag e 3 to deter-
mine the correct procedure to mount your display
using the applicable VESA mounting-hole pattern
configuration.
Figure 5. Install FWD-111 on Wall Bracket
Set screw
Figure 6. Tighten Setscrew to Secure
7
Page 8
Installation Instructions FWD-111
Flush Mount – 75mm/100mm Pattern
To flush mount the display using the 75mm/100mm mounting
hole pattern, do the following:
1. Install two M4 x 12mm screws (20) into the top mounting
holes on the display (see Figure 7 and Figure 8).
2. Align the mounting holes on the Centris mount with the
screws installed on the display. Hang the display on the
mount.
3. Install two remaining M4 x 12mm screws (20) into the
bottom mounting holes on the display.
4. Secure the display to the mount by tightening all fo ur
M4 x 12mm screws (20).
5. Proceed to “CABLE MANAGEMENT” on page 10 and
the “ADJUSTMENTS” on page 10 and perform those two
procedures to complete the installation process.
75mm/75mm
VESA Pattern
(Inside Mounting Holes)
Figure 7. 75mm/100mm VESA Mounting Patterns
100mm/100mm
VESA Pattern
(Outside Mounting Holes)
Recessed Mount – 75mm/100mm Pattern
T o recess mount the display using the 75mm x 100mm mounting hole pattern, do the following:
20
NOTE: Use one of the following screw and spacer combina-
tions: (30 with 40) or (50 with 60).
CAUTION: If your display uses a screw size other than
M4 X 20mm or M4 X 30mm, DO NOT use the
M4 X 20mm or M4 X 30mm screws. Using the
wrong screws could result in damage to your display.
1. Select four screws (30 or 50) and four spacers (40 or 60),
depending on your display model.
2. Place four spacers (40 or 60) over the mounting holes on
the back of your display (see Figure 7, Figure 8
and Figure 9).
3. Align the mounting holes on the Centris mount with the
spacers installed on the back of your display.
4. Secure the mount to your display using the four screws (30
or 50) that were selected in step 1.
5. Perform the procedure to “Install FWD-111 on Wall
Bracket” on page 7.
6. Proceed to “CABLE MANAGEMENT” on page 10 and
the “ADJUSTMENTS” on page 10 and perform those two
procedures to complete the installation process.
Figure 8. Flush Mount – 75mm/100mm Pattern
30 or 50
40 or 60
8
Figure 9. Recessed Mount – 75mm/100mm Pattern
Page 9
Installation Instructions FWD-111
200mm/100mm Pattern
To mount the display using the 200mm x 100mm mounting
hole pattern, do the following:
1. Attach interface bracket (70) to the display using six
M4 x 12mm flat head screws (80). See Figure 10.
2. Start two M4 x 5mm Phillips pan head screws (90) into the
top two mounting holes of the display (see Figure 11).
3. Hang the mount from th e two screws started in Step 2.
4. Install the remaining two M4 x 5mm Phi llips pan head
screws (90) into the bottom two mounting holes of the display.
5. Secure the display to the mount by tightening all four
M4 x 5mm Phillips pan head screws (90).
6. Proceed to “CABLE MANAGEMENT” on page 10 and
the “ADJUSTMENTS” on page 10 and perform those two
procedures to complete the installation process.
Installing Non-VESA Compliant Mounts
1. For custom interface brackets, contact:
Chief Manufacturing.
80
70
Figure 10. Install 200mm/100mm Pattern
90
Figure 11. Hang Display onto Mount
9
Page 10
Installation Instructions FWD-111
CABLE MANAGEMENT
WARNING:Make sure your cables do not run through a
pinch point.
1. Connect and secure power/audio/video cables, making
sure to leave sufficient slack to allow for movement of the
display.
2. Route power/audio/video cables under each arm, allowing
sufficient slack in cables for extension and avoiding pinch
points
3. Secure cables using cover plates (130) and four screws
(140).
ADJUSTMENTS
CAUTION: Overtightening adjustment will cause
excessive wear.
Rotational Tilt, Pitch, and Roll Adjustment
1. Test the Centris adjustment by tilting, pitching, and rolling
the Centris mount interface (see Figure 12).
2. If necessary, remove display from the mount.
3. Use a Phillips screwdriver to tighten or loosen the Centris
adjustment screw.
4. Check for desired tension.
5. Repeat the procedure until desired tension is obtained.
Lateral Tension Adjustment
1. Using a 3/16” hex wrench (150), slightly tighten or loosen
lateral tension adjustment bolt (see Figure 13).
2. Check for desired tension.
3. Repeat Steps 1 and 2 until desired tension is obtained.
Figure 12. Adjust Centris Adjustment Screw
Lateral Tension Adjustment Bolts
10
Figure 13. Lateral Tension Adjustment
Page 11
Page 12
Loading...