Chicco Corso User guide

Read all instructions BEFORE
assembly and USE of product.
KEEP INSTRUCTIONS FOR
FUTURE USE.

IS0185E_01

Corso

™

Stroller

Owner's Manual

©2019 Artsana USA, INC. 09/19

www.chiccousa.com

WARNING

Failure to follow all warnings and instructions may result in

serious injury or death. For your child's safety, read the labels and

owner's manual before using the product.

• PLEASE SAVE OWNER'S MANUAL
FOR FUTURE USE.

• ADULT ASSEMBLY REQUIRED.

• NEVER LEAVE CHILD
UNATTENDED. Always keep child
in view while in the stroller.

• AVOID SERIOUS INJURY from
falling or sliding out. Always use
seat belt. After fastening buckles,
adjust belts to get a snug fit around
your child.

• AVOID FINGER ENTRAPMENT: Use
care when folding and unfolding
the stroller. Be certain the stroller
is fully opened and latched before
allowing your child near the
stroller.

• USE OF THE STROLLER with a
child weighing more than 50 lbs
(22.7 kg), will cause excessive wear
and stress on the stroller. Use the
stroller with only one child at a
time.

• STROLLER TO BE USED only
at walking speed. Product not
intended for use while jogging,
skating, etc.

• TO PREVENT A HAZARDOUS,
UNSTABLE CONDITION, never
place purses, shopping bags,
parcels or accessory items on the
canopy or handle. Do not place
more than 10 lbs (4.5 kg) in the
storage basket. Do not place more
than 1 lb (0.5 kg) in each seat back
pocket.

2

• DO NOT use storage basket as a
child carrier.

• NEVER ALLOW YOUR STROLLER to
be used as a toy.

• DISCONTINUE USING YOUR
STROLLER should it become
damaged or broken.

• AVOID STRANGULATION. DO
NOT place items with a string
around your child's neck, suspend
strings from this product, or attach
strings to toys.

• NEVER USE STROLLER ON STAIRS
or escalators. You may suddenly
lose control of the product and
your child may fall out. Also, use
extra care when going up or down
a step or curb.

• Do not attempt to attach any
infant car seat to the stroller other
than the Chicco infant car seat.
Injury or death may result when
attempting to use this stroller in
conjunction with infant car seats
from other manufacturers.

• Before use, remove and dispose
of all plastic bags and packaging
materials and keep them out of
reach of children.

• Before assembly, check that the
product and all of its components
have not been damaged during
transportation.

WARNING

Failure to follow all warnings and instructions may result in

serious injury or death. For your child's safety, read the labels and

owner's manual before using the product.

• Do not use accessories, spare parts,
or any component not supplied or
approved by Chicco as they may
make the stroller unsafe.

Using Chicco Infant car seat
with stroller:

• Infant Car Seat Adapter must
be properly attached to use the
Chicco infant car seat.

• ONLY USE a Chicco infant car seat
with this product.

• Only use this product to transport
infants that are within the size and
weight limitations of the infant car
seat.

• FALL HAZARD: Always check that
infant car seat is securely attached
to stroller frame by pulling up on
the infant car seat.

• ALWAYS SECURE your child with
the car seat harness. Always make
sure child is properly harnessed in
the car seat.

• Refer to your Chicco infant car
seat owner's manual for additional
warnings and use instructions
before using this product.

3

Components

A.

B.

C.

A. - Stroller Frame

B. - Front Wheels

C. - Rear Wheels

4

D.

D. - Rear Axle

Components

E.

G.

H.

E. - Washers

F.

F. - Pins

G. - Hubcaps

Note: Parts E, F, and G are in a small red bag.

H. - Seat Frame

I.

I. - Armbar

5

Components

K.

J.

J. - Canopy

K. - Infant Car Seat Adapter

6

How to Assemble Stroller

WARNING

When opening the Stroller, ensure that your child, or other children, are at a
safe distance. Ensure that during these operations, the movable parts of the
Stroller do not come into contact with your child.

1

“CLICK!”

If you have hardwood floors or
linoleum you may want to
perform this step on carpeting
or lay down some protection for
your floors.

1. Stand the Stroller Frame (A) on
end, as shown. Locate the handle
and rotate the handle up and
unfold the Stroller Frame. Make
sure the frame is fully open and
locked by pressing down on the
handle.

7

How to Assemble Stroller

2

2. Insert the Rear Axle (D) into
the opening on the Rear Stroller
Frame, as shown. Make sure to
insert the end without the ears
first. Slide it through until the
axle comes out on the other side.
Make sure the Axle is centered

between both brake levers.

8

How to Assemble Stroller

2

3A

3A. On one side of the Rear Axle,
slide a Rear Wheel (C), and turn the
Wheel until the brake tab fits into
one of the grooves on the Wheel.

9

How to Assemble Stroller

3B

3C

3B. On the same side slide a
Washer (E) onto the Rear Axle.

3C. Secure the Wheel to the Rear
Axle using the Pin (F). Push the
straight side of the Pin through the
hole on the Rear Axle. The curve
on the Pin must curve around the
outside of the Rear Axle, as shown.
Make sure Washer is between the
Pin and Wheel.

10

How to Assemble Stroller

WARNING

Check that the wheels are fitted correctly.

3D

3D. Line up the tabs on the
Hubcaps (G) with the holes on the
Wheel. Snap the Hubcap onto the
Wheel to cover the Washer and
Pin. Repeat Step 3 for other side.

Pull on each Wheel to make sure
the Wheel assembly is securely
attached to the frame.

11

How to Assemble Stroller

4

4. Attach the Front Wheel (B) to
the Stroller Frame by lining up and
inserting the Front Wheel Pin into
the corresponding opening on
the Stroller Front Leg, as shown.
Repeat for the other side.

Make sure both Wheels are
secure by pulling down on
Wheel assemblies.

12

Front Wheel Swivel Locks

The stroller has front Swivel/Fixed wheels. It is recommended that you use
the Fixed Mode on uneven surfaces and the Swivel Mode on normal road
surfaces. When using swivel locks, make sure you lock both front wheels.

5

5. To release the Front Wheel to a
Swivel position, push down on the
Buttons located above the Front
Wheels, as shown. To lock the
Front Wheels push up on the
Buttons and move the stroller
forward. The wheels will lock into
a straight position.

13

Remove Front Wheels

6

6. Remove the Front Wheels by
pushing in on the Release Button,
just above the wheel (as shown).
And, at the same time, pull the
Front Wheel off of the Stroller
Frame. Repeat for the other side.

14

7A

7B

“CLICK!”

How to Use the Seat

7A. Open the Seat Frame (H). Line
up and insert the hubs on both
sides of the Seat Frame into the
hub slots on the Stroller Frame as
shown (7B). Pull up on the Seat
Frame to make sure it is securely
attached to the Stroller Frame.

15

How to Use the Seat

8

8. Press the buttons on both hubs,
as shown, and pull up to remove
the Seat Frame.

Note: The Seat Frame can be
attached in a Forward Facing
position and a Parent Facing
position, as shown.

16

Forward Facing Position Parent Facing Position

How to Use the Seat

9

The Seat can be adjusted to 3
positions.

9. To recline the Seat, press the
Recline Button on the back of the
Seat, as shown. Rotate the Seat up

or down to the desired position.

1.

2.

3.

17

How to Use the Seat

10

1.

2.

The Footrest can be adjusted to 4
positions.

10. Press in on both Footrest
Buttons and, at the same time,
rotate the Footrest up or down to
the desired position.

3.

4.

18

11

How to Use the Canopy

11. To attach the Canopy, slide
the Canopy attachment clips
onto the corresponding
attachment points on the Seat
Frame, as shown. Make sure that
back panel of Canopy is located
behind the seat frame.

19

How to Use the Canopy

12A

12B

12A. To open the Canopy, pull the
front edge of the Canopy forward.
Reverse this step to close the
Canopy.

12B. Pull forward on the Canopy
flap to uncover the mesh panel.
Reverse this step to close the mesh

panel.

20

12C

How to Use the Canopy

12C. To Extend the Canopy, unzip
the zipper and pull forward on the
front Canopy edge. Reverse this

step to close the extension panel.

21

How to Use the Canopy

13

13. To remove the Canopy, pull up
on the attachment clips on each
side of the Canopy at the same

time.

22

Using the Brakes

WARNING

Always apply the brakes whenever the stroller is stationary. Never leave the
stroller on a sloped surface, with a child onboard, even with the brakes applied.

14A

14B

14A. Push down on the Brake Lock
Levers located on each side of the
Rear Wheel assembly, to lock the
Rear Wheels.

14B. Pull up on the Brake Lock
Levers to unlock the Rear Wheels.

23

Using the Suspension

15

The Stroller has 2 Suspension
Modes.

15. Flip the Lever up for smooth
terrain and flip the Lever down for
rough terrain. Make sure both of
the Suspension Levers are in the
same position.

A straight line ( ) indicates
a stiff suspension, a stable ride for
more control on smooth terrain.

24

A wavy line ( ) indicates a
soft suspension, a smoother ride
on rough terrain.

16A

16B

Accessory Pockets

WARNING

Never place more than 1 lb (0.5 kg) in each seat back pocket.

16A. Locate the 4 accessory
pockets on the inside of the basket.

2 bottle pockets in back corners
and 2 organizer pockets on sides.

16B. Locate the 2 accessory
pockets on the back of the seat.

1 zippered organizer pocket and 1
mesh organizer pocket.

25

How to Use Safety Harness

WARNING

T

his stroller features three harness positions. Always use a harness position
located ABOVE the child's shoulder line. If multiple harness positions are
above the child's shoulder line, use the one closest to it.

17A

17A. The Shoulder Straps can be
adjusted to 3 height positions as
shown.

3

2

1

26

How to Use the Safety Harness

17B

17B. To adjust the Shoulder
Harness to another height position,
locate the D-ring on the back of
the seat as shown. Slide the D-ring
through opening on the seat back.
Then pull through the opening on
the seat pad. Re-insert the D-ring
into the correct height position,
and repeat for the other side.
Always use the same height
position for both straps. Depending
on Shoulder Harness height
position, D-ring may be located
below visible opening in seat back.

Seat Front

27

How to Use the Safety Harness

18

18. This stroller has a 5-point
safety harness. The Shoulder
Strap Connector is designed to
break away from the Waist Clip
when not secured in the Crotch
Strap Buckle.

Make sure the Shoulder Strap
Connector is in the correct
position, as shown. Slide the
Shoulder Strap Connector onto
the Waist Strap Clip and repeat
for the other side. Then slide both
Waist Clips into the Crotch Strap
Buckle, as shown. Pull on both
sides to make sure the Clips are
secured to the Buckle.

28

How to Use the Safety Harness

WARNING

Never leave child unattended. Avoid serious injury from falling or sliding out.

Always use seat belt.

19

19. The Safety Harness can be
released by pressing the button
on the center of the Buckle and
pulling both Waist Clips out.

Pull up on the Shoulder Strap
Connector to remove it from the
Waist Strap Clip.

29

How to Use the Safety Harness

20

20. The length of the Shoulder
Straps can be adjusted by
pulling on the adjustment
buckles to tighten or loosen.

The length of the waist straps
can be adjusted. Press the tab at
the end of the Waist Strap Clip
and pull on the strap to tighten or
loosen, to better fit your child.

30

How to Use the Armbar

21A

21B

21A. To use Armbar (I), Insert
the Armbar Tongues into the
corresponding openings on the
Seat Frame. To release the Armbar
press in on the buttons located at
the sides of the Armbar, as shown
(21B).

“CLICK!”

31

How to Use the Infant Car Seat Adapter

WARNING

Do not remove the Seat from the Stroller frame with the child inside.

22A

22A. Remove the Seat from the
Stroller Frame (refer to Step 8).
Rotate both arms on the Infant Car
Seat Adapter (K) down, as shown.

32

How to Use the Infant Car Seat Adapter

22B

“CLICK!”

22B. Line up the Tongues on both
sides of the Infant Car Seat Adapter
to the slots on the Stroller frame
as shown. Push down until it clicks
into place. Pull up on the Infant
Car Seat Adapter to make sure it
is securely attached to the Stroller
Frame.

33

22C

How to Use the Infant Car Seat Adapter

22C. To remove the Infant Car Seat
Adapter, press both buttons on the
attachement and pull up.

34

Using the Chicco Infant Car Seat

WARNING

ONLY USE a Chicco infant car seat with this product. Always make sure
child is properly harnessed in the car seat. Only use this product to transport
infants that are within the size and weight limitations of the infant car seat.
Refer to your Chicco infant car seat owner's manual for additional warnings
and use instructions before using this product.

35

Using the Chicco Infant Car Seat

23A

23B

23A. With the Infant Car Seat
Adapter attached, place the
Chicco infant car seat into the
Stroller Frame. The infant car
seat can be attached in a
Forward Facing or Parent Facing
position. Make sure infant car
seat clicks into the Stroller Frame
on both sides.

“CLICK!”

1

2

Pull up on the infant car seat;
make sure it is secured to Stroller
Frame (23B). If the infant car
seat is not secured see Step 22
to make sure the Infant Car Seat
Adapter is assembled and
attached correctly.

36

CLICK!

!

CLIC!

CHECK!

!
VERIFICAR!

Using the Chicco Infant Car Seat

24

Parent Facing

Position

24. To remove the infant car seat ,
squeeze the Release Handle on the
back of the infant car seat and lift
up on the carrying handle.

Note: The infant car seat can be
attached in a Forward Facing
position and a Parent Facing
position, as shown.

Forward Facing

Position

37

How to Fold the Stroller

WARNING

When folding the Stroller, make sure that your child and other children are at
a safe distance. Ensure that during the operations, the movable parts of the
Stroller do not come in contact with your child.

25A

With the Seat attached:

25A. To Fold the Stroller, lock rear
wheel brakes, and make sure the
Front Wheels are in Swivel Mode.
Lift up on the bottom edge of the
Seat frame and fold in half.

Note: The stroller will fold to its
smallest size when the seat is
attached forward facing and
adjusted to the most upright
position.

38

25B

How to Fold the Stroller

25B. Locate the Fold Handle and
lift up on the handle, as shown.
When the Stroller is folding,
the front wheels will swivel to
the side and Push Handle will
fold down to make the Stroller
compact.

39

How to Fold the Stroller

26

With the Infant Car Seat Adapter
attached:

26. To Fold the Stroller, lock rear
wheel brakes, and make sure the
Front Wheels are in Swivel Mode.
Fold the front section of the Infant
Car Seat Adapter towards the back
section. Locate the Fold Handle
and lift up on the handle, as shown
in 25B.

40

27

How to Remove the Seat Fabric

27. Remove the Seat from the
Stroller Frame. Flip the Seat frame
over and undo the Seat strap.
Unsnap 2 snap buttons on one side
of the Stroller Frame as shown.

Repeat for the other side.

41

28

How to Remove the Seat Fabric

28. Locate both snap buttons on
the footrest frame. Press in the
snap button and pull the footrest
from stroller frame. Repeat for the
other side and slide the seat frabric

from the footrest as shown.

42

29

How to Remove the Seat Fabric

29. Flip the Seat back over to the
front. Remove the Seat from the
Stroller Frame. Locate the zipper
on the side of the seat and undo
the zipper.

43

How to Remove the Seat Fabric

30A

30B

30A. Undo the hook and loop and
locate the Shoulder Strap D-rings.
Push the Shoulder Strap D-rings
through the seat back (refer to
Step 17B). Pull the Shoulder Straps
through the front side to remove.

30B. Make sure to push the waste
belt straps through the openings in
the seat fabric, as shown.

44

How to Remove the Seat Fabric

30C

30C. Remove the plastic board in
the seat back.

45

How to Remove the Seat Fabric

31A

31B

31A. Undo the hook and loop and
locate the crotch strap D-ring.
Push the D-ring through the
opening on the seat bottom. Pull
the crotch strap through the front
side to remove.

31B. Remove the plastic board in
the seat bottom.

46

How to Remove the Seat Fabric

32

32. To remove the crotch strap
pad and the shoulder pads. Locate
the positioner strap tab (on the
crotch strap) and thread it through
the buckle slot. Repeat for the
D-ring on the crotch strap and
both shoulder straps. Remove the
crotch pad and shoulder pads from
the straps.

47

33

How to Reattach the Seat Pads

33. To attach the crotch strap pad,
thread the crotch strap through
the crotch pad. Locate both
positioner strap tabs and insert
the tab into the opening below
the crotch buckle and the slot on
the D-ring. Pull the positioner tab
through to the back of the crotch
buckle, as shown.

48

How to Reattach the Seat Pads

34

34. To attach the shoulder strap
pad, thread the shoulder strap
through the shoulder pad. Locate
the positioner strap tab and insert
the tab into the slot on the D-ring,
as shown. Repeat for the other
shoulder strap pad.

49

Cleaning and Maintenance

This product requires regular maintenance. The cleaning and maintenance of the
stroller must only be carried out by an adult.

CLEANING

Removable fabric parts of the product may be machine washed separately in cold
water and mild soap on delicate cycle. No bleach. Drip dry.

Periodically wipe clean plastic parts with a soft damp cloth. Always dry the metal
parts to prevent the formation of rust if the stroller has come into contact with
water.

MAINTENANCE

Lubricate the moving parts only if necessary, with a light application of a silicone
based lubricant. Periodically check the condition of the wheels, and keep them
clean of dust and sand. To avoid friction that may prevent the correct operation of
the stroller, ensure that all the movable plastic parts placed along the metal frame
are clean of dust, dirt or sand. Keep the stroller in a dry place. Prolonged
exposure to direct sunlight may cause the fabric to fade.

50

For More Information

@

If you have any questions or comments about this product, or are missing any
of the parts please do not return this product to the store. Contact us in one of
the following ways:

(877)-424-4226

[e-mail]

www.chiccousa.com

1826 William Penn Way
Lancaster, PA 17601

51

52

www.chiccousa.com