Page 1
WHITE PVC
®
TRELLIS
91761
ASSEMBLY INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www .harborfreight.com
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight T ools .
For technical questions and replacement parts, please call 1-800-444-3353
Page 2
Specifications
Overall Dimensions
Bench Max. Weight Capacity
Materials
Weight
58-5/8” Wide X 27-1/4” Deep X 97” High
200 Lbs.
White PVC-U.V. treated for Weather Protection
89 Lbs.
Save This Manual
Y ou will need the man ual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice
with this manual. Write the invoice n umber on the inside of the front cover . K eep the
manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Keep children away. Children must never be allowed in the work area. Do not
let children play on this product without supervision.
4. Dress properly. Do not wear loose clothing or je welry as they can be caught in
moving parts. Protectiv e, electrically nonconductive clothes and nonskid footw ear
are recommended when working.
5. Use eye and ear protection. Always wear ANSI approved impact safety goggles
when assembling this product.
6. Do not overreach. Keep proper f ooting and balance at all times. Two or more
people are needed to assemble this product.
7. Use the right tool for the job. Do not attempt to force a small product or
attachment to do the work of a larger industrial product. There are cer tain
applications for which this product was designed. Do not modify this product and
do not use this product for a purpose for which it was not intended.
8. Stay alert. Watch what you are doing, use common sense . Do not assemb le this
product when you are tired.
9. Check for damaged parts. Before using this product, any par t that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for loose parts and any other condition
that may affect the operation of this product. Replace loose or worn parts
immediately . Any part that is damaged should be properly repaired or replaced
by a qualified technician.
SKU 91761 For technical questions, please call 1-800-444-3353. Page 2
Page 3
10. Warning: Locate Trelllis in a spot that is flat without an unev en surface, a wa y from
electrical wires. Caution: Hea vy winds could make the Trellis unstable.
11. Always distribute objects on Bench evenly. Uneven weight distribution could
cause toppling. Do not allow children to climb on the Trellis.
Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur . It must
be understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied b y the operator .
Unpacking
When unpacking, check to make sure the f o llowing parts are included. If any parts are
missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual.
Assembly Instructions
1. Assemble all parts on a smooth surface to avoid scratching. These parts fit
together and no hardware is required.
2. “Ladder”Assembly: Use Cross Beams (2) and Bars (3) to form “ladder”.
Set aside.
3. “Side Lattice” Assembly: Use four Bars (4) (horizontally), three Bars (5)
(vertically) with two Bars (11) (horizontally) at the top and bottom to build the
“lattice” assembly. Repeat instructions for the second side “lattice”.
See Figure B.
See Figure A.
4. Still working with the par ts on the ground, fit the Support Bar (7) between
the Posts (6). Fit the side “lattice” assembly between the two P osts (6). Repeat
for second side, “lattice” with Posts. Be sure all connections are secure.
See Figure B.
Bars (3)
Cross
Beams (2)
Figure A
SKU 91761 For technical questions, please call 1-800-444-3353. Page 3
Post (6)
Bars (4)
(horizontal)
Bars (5)
(vertical)
Bars (11)
(horizontal)
Support Bar
(7)
Bars (11)
(horizontal)
Figure B
Page 4
5. Choose your location: The location site should be a flat, even surface (three
possible set-up options:
should be taken:
prevent toppling.
Test that the Trellis is level. Pack dirt around Posts (6).
holes before positioning the Posts (6). Test that the Trellis is level.
1.)
The Trellis can be free standing but
caution
Always distribute weight evenly on the bench to
2.)
Stand the Trellis upright and place in 6” deep holes.
3.)
Place cement in the
If you are
not experienced in setting up this type of product, it is recommended that you
seek the assistance of a qualified handyman for placement of your Trellis.
6. Place the assembled sides of the Trellis flat on the ground nearest to the
location. With an assistant, insert the “ladder assembly” into the Posts (6).
See Figure C.
Gothic Cap (1)
Post (6)
Ladder
Assembly
Figure C
Metal
Bars
Clamps
Support
Bar (7)
Bench (8)
Figure D
Figure E
Figure F
7. There must be metal bars inserted in the two Braces (8) to support the weight
placed on the Bench (8).
Bar (7).
See Figure F–G.
8. Tap the Gothic Caps (1) on the end of each Post (6).
See Figure D.
Snap the Bench (8) over the Support
See Figure C.
SKU 91761 For technical questions, please call 1-800-444-3353. Page 4
Page 5
9. Place Covers (9) (not shown) over the ends of the “ladder” that are exposed.
Place the Covers (10) (not shown) o v er the Brace (8) pieces of the Bench. Tap
into place.
See Figure F.
10. After assembly of the T rellis is complete, test that the product is solid and stab le
before using the T rellis .
Cover (9)
Bench (8)
Support
Bar (7)
Figure G
Figure H
Parts List
Part # Description Qty.
4” X4” Gothic Cap
1
62” x 2” x 3-1/2” Cross Beam
2
21” X 1-1/2” x 1-1/2” Bar
3
25” x 1-1/2” x 1-1/2” Bar
4
47.5” x 13/16” x 1” Bar
5
89” x 4” x 4” Post
6
20-1/2” x 2” x 3-1/2” Support Bar
7
59” x 2” x 6” Bench
8
2 x 3-1/2” Cover
9
2” x 6” Cover
10
25” x 1-1/2” x 1-1/2” x 1-1/2” Bar
11
4
2
9
8
6
4
2
2
4
4
4
Cover (10)
SKU 91761 For technical questions, please call 1-800-444-3353. Page 5
Page 6
Assembly Drawing
(1)(2)
(9)
(11)
(3)
(5))
(4)
(8)
(6)
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFA CTURER AND/OR DISTRIBUTOR HAS PRO VIDED THE P A RTS DIAGRAM IN THIS MANUAL AS
A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENT ATION OR WARRANTY OF ANY KIND T O THE BUYER THAT HE OR SHE IS QUALIFIED T O
MAKE ANY REP AIRS T O THE PRODUCT OR THA T HE OR SHE IS QU ALIFIED T O REPLACE ANY P AR TS OF
THE PRODUCT . IN F ACT, THE MANUF ACTURER AND/OR DISTRIBUT OR EXPRESSLY STATES THat ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT
OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INST ALLA TION OF REPLA CEMENT P ARTS THERET O.
(7)
(10)
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
SKU 91761 For technical questions, please call 1-800-444-3353. Page 6
Loading...