Chicago Electric 3/4 HP DIRTY WATER SUBMERSIBLE PUMP WITH FLOAT User Manual

3/4 HP DIRTY WATER SUBMERSIBLE

PUMP WITH FLOAT

94649

ASSEMBLY AND OPERATING INSTRUCTIONS

Due to continuing improvements, the product shown above may differ slightly from the actual product.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

REV 08i

Specifications

Motor
Pump Cord
Discharge Size
Discharge Fittings
Delivery Height
Flow Rate
Horsepower
Max. Particle Size

Warning: The pump should not be submerged in water deeper than the length of the
power cord, which is 18 feet long.

120 V, 60 Hz, 7 Amp
18 Ft. - 3 Prong Plug
1-1/2”
1-1/2”, 1-1/4” and 1”

26.6 Ft.
3300 GPH
3/4 HP
1”

Min. Water Level
Operating Temp.
Min. Switch Level
Dimensions
Housing Material
Pump Weight
Motor Drive

4”
95° F
3”
6” Dia. x 13-1/2” H
PP Plastic

10.4 lb.
Magnetic Drive

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Avoid pump damage. Do not operate dry. Never lift or transport the pump by the
power cable or float switch cable.

2. Do not pump certain liquids. Do not pump gasoline, hydrocarbons, fuel oil,
kerosene, fats, salt or waste water, or chemical agents. Do not pump hot liquids.

3. Avoid fire or explosion. Do not pump in close proximity to flammable or explosive
materials.

4. Avoid working alone. If an accident happens, an assistant can bring help.

5. Avoid electrical shock. If the submersible pump is to be installed in a location
where a breakdown or fault could cause injury to persons, or damage to objects, the
power source must utilize a Ground Fault Circuit Interrupter (GFCI). This device will
immediately shut down power in case of a short circuit. This device must be tested
periodically. No persons should be in contact with the water being pumped.

6. Keep children away. Children must never be allowed in the work area. Do not let
them handle machines, tools, or extension cords.

7. Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.

REV 07/06

Page 2SKU 94649

8. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically nonconductive clothes and nonskid footwear are
recommended when working. Wear restrictive hair covering to contain long hair.

9. Use eye and ear protection. Always wear ANSI approved impact safety goggles.

10. Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across electrical cables or frames.

11. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.

12. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified technician.
Do not use the tool if any switch does not turn On and Off properly.

13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor Freight
Tools.

14. Use proper power outlet. This pump has a three prong plug. The third prong (round)
is the ground. Plug the pump cord only into a three-prong, Ground Fault Circuit
Interrupter receptacle. Cutting off the ground prong will result in a safety hazard and
void the warranty.

15. Using Extension Cords. An extension cord up to 50 feet must have a wire size
of 18 AWG; up to 100 feet must have a wire size of 16 AWG. Do not submerge
extension cords or make contact with water. Note: Do not make the extension cord

connection underwater.

16. Use the right tool for the job. Do not attempt to force a small tool or attachment to
do the work of a larger industrial tool. There are certain applications for which this tool
was designed. Do not modify this tool and do not use this tool for a purpose for which
it was not intended.

17. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.

18. Pacemaker safety warning. People with pacemakers should consult with their
physician(s) before using this product; operation of equipment in close proximity to a
heart pacemaker could cause interference or failure of the pacemaker.

Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.

Page 3SKU 94649