Service
Fuel
Checking Things Under the Hood
All-Wheel Drive
Rear Axle
Four-Wheel Drive
Front Axle
Headlamp Aiming
Bulb Replacement
Windshield Wiper Blade Replacement
Tires
Appearance Care
Vehicle Identification
Electrical System
Capacities and Specifications
Maintenance Schedule
Maintenance Schedule
Customer Assistance Information
Customer Assistance and Information
Reporting Safety Defects
Vehicle Data Recording and Privacy
GENERAL MOTORS, GM, the GM Emblem,
CHEVROLET, the CHEVROLET Emblem, and the
name TRAILBLAZER are registered trademarks
of General Motors Corporation.
This manual includes the latest information at the time it
was printed. GM reserves the right tomakechangesafter
that time without further notice. For vehiclesfirstsoldin
Canada, substitute the name “General Motors ofCanada
Limited” for Chevrolet Motor Division wherever itappears
in this manual.
This manual describes features that may or may not be
on your specific vehicle.
Read this manual from beginning to end to learn about
the vehicle’s features and controls. Pictures, symbols,
and words work together to explain vehicle operation.
Keep this manual in the vehicle for quick reference.
Litho in U.S.A.
Part No. 25820780 A First Printing
Canadian Owners
A French language copy of this manual can be obtained
from your dealer/retailer or from:
Helm, Incorporated
P.O. Box 07130
Detroit, MI 48207
1-800-551-4123
helminc.com
Propriétaires Canadiens
On peut obtenir un exemplaire de ce guide en français
auprès de concessionnaire ou à l’adresse suivante:
Helm Incorporated
P.O. Box 07130
Detroit, MI 48207
1-800-551-4123
helminc.com
Index
To quickly locate information about the vehicle use the
Index in the back of the manual. It is an alphabetical
list of what is in the manual and the page number where
it can be found.
2008 General Motors Corporation. All Rights Reserved.
ii
Safety Warnings and Symbols
A circle with a slash
through it is a safety
symbol which means
“Do Not,” “Do not do this” or
“Do not let this happen.”
A box with the word CAUTION is used to tell about
things that could hurt you or others if you were to ignore
the warning.
{ CAUTION:
These mean there is something that could hurt
you or other people.
Cautions tell what the hazard is and what to do to avoid
or reduce the hazard. Read these cautions.
A notice tells about something that can damage the
vehicle.
Notice: These mean there is something that could
damage your vehicle.
Many times, this damage would not be covered by the
vehicle’s warranty, and it could be costly. The notice
tells what to do to help avoid the damage.
There are also warning labels on the vehicle which use
the same words, CAUTION or Notice.
iii
Vehicle Symbols
" : Charging System
The vehicle has components and labels that use
symbols instead of text. Symbols are shown along
with the text describing the operation or information
relating to a specific component, control, message,
gage, or indicator.
M : This symbol is shown when you need to see your
owner manual for additional instructions or information.
* : This symbol is shown when you need to see a
service manual for additional instructions or information.
Vehicle Symbol Chart
Here are some additional symbols that may be found on
the vehicle and what they mean. For more information
on the symbol, refer to the index.
0 : Adjustable Pedals9 : Airbag Readiness Light# : Air Conditioning
! : Antilock Brake System (ABS)g : Audio Steering Wheel Controls or OnStar
®
$ : Brake System Warning Light
I : Cruise ControlB : Engine Coolant TemperatureO : Exterior Lamps# : Fog Lamps
. : Fuel Gage+ : Fusesi : Headlamp High/Low-Beam Changerj : LATCH System Child Restraints
* : Malfunction Indicator Lamp
: : Oil Pressure
} : Power
/ : Remote Vehicle Start
> : Safety Belt Reminders
7 : Tire Pressure Monitor
F : Traction Control
M : Windshield Washer Fluid
iv
Section 1Seats and Restraint System
Front Seats ......................................................1-2
Restraint System Check ..................................1-70
Checking the Restraint Systems ......................1-70
Replacing Restraint System Parts
After a Crash ............................................1-71
.1-63
1-1
Front Seats
Manual Seats
{ CAUTION:
You can lose control of the vehicle if you try to
adjust a manual driver’s seat while the vehicle is
moving. The sudden movement could startle and
confuse you, or make you push a pedal when you
do not want to. Adjust the driver’s seat only when
the vehicle is not moving.
If the vehicle has a manual seat, it can be moved
forward or rearward.
1. Lift the bar to unlock
the seat.
2. Slide the seat to the
desired position and
release the bar.
Try to move the seat with your body to be sure the seat
is locked in place.
1-2
Power Seats
Manual Lumbar
On vehicles with power
seats, the controls used to
operate them are located
on the outboard side of
the seats.
To adjust the seat:
• Move the seat forward or rearward using the
horizontal control.
• Raise or lower the front of the seat cushion using
the front of the horizontal control.
• Raise or lower the rear of the seat cushion using
the rear of the horizontal control.
• Raise or lower the entire seat using the entire
horizontal control.
For seats with power reclining seatbacks, see “Power
Reclining Seatbacks” under Reclining Seatbackson page 1-7.
On vehicles with this
feature, the knob is
located on the outboard
side of the driver seat.
Turn the knob to increase or decrease lumbar support.
1-3
Power Lumbar
Heated Seats
On vehicles with power
lumbar, the control is
located on the outboard
side of the seat.
To increase or decrease support, hold the control
forward or rearward.
1-4
Your vehicle may have
heated front seats. The
buttons used to control this
feature are located on the
front door armrests. The
engine must be running
for the heated seat feature
to work.
To heat the entire seat, press thehorizontalbuttonwith
the heated seat and seatback symbol. Pressthebuttonto
cycle through the temperature settings of high,medium,
and low and to turn the heatedseatoff. The indicator
lights above the button will come ontodesignatethe
level of heat selected: three for high,twoformedium,
and one for low. The low settingwarmstheseatbackand
seat cushion until the seat temperature isnearbody
temperature. The medium and high settings heatthe
seatback and seat cushion to a slightlyhigher
temperature. You will be able to feelheatinabout
two minutes.
To heat only the seatback, press the vertical button with
the heated seatback symbol. An indicator light on the
button will come on to designate that only the seatback
is being heated. Additional presses will cycle through
the heat levels for the seatback only.
The feature will shut off automatically when the ignition
is turned off.
Memory Seat
If your vehicle has this
feature, the controls for
the memory function
are located on the
driver door.
These buttons are used to program and recall memory
settings for the driver’s seating position and the
adjustable pedals, if equipped. The settings for these
features can be saved for up to two drivers.
To store the memory settings:
1. Adjust the driver’s seat, including the seatback
recliner and lumbar and the adjustable pedals,if
equipped, to the desired position.
See Adjustable Throttle and Brake Pedal onpage 2-24 for more information.
2. Press and hold the 1 or 2 button of the memory
control for three seconds. A double chimewillsound
to let you know that the positionhasbeenstored.
To repeat the procedure for a seconddriver,followthe
preceding steps, but press the other numberedmemory
control button.
To recall the memory settings, do one of the following:
• Press and release button 1 or 2 while the vehicle
is in (P) Park. A single chime will sound and the
memory position will be recalled.
• If programmed to do so through the Driver
Information Center (DIC), pressing the unlock button
on the remote keyless entry transmitter will recall
the preset driver’s memory seat and adjustable
pedals position. The numbers on the back of the
transmitters, 1 or 2, correspond to the numbers
on the memory controls.
• If programmed to do so through the DIC, placing
the key in the ignition will recall the driver’s
memory seat and adjustable pedals positions.
1-5
See “Seat Recall” under DIC Vehicle Customization onpage 3-56 for more information.
To stop recall movement of the memory seat feature at
any time, press one of the memory buttons or power
seat controls.
Easy Exit Seat
The control for the easy exit seatfunctionislocatedon
the driver’s door below the memory buttons 1 and 2.
The easy exit seat button is usedtoprogramandrecall
the desired driver’s seat position when exitingorentering
the vehicle. The power lumbar, recline, andadjustable
pedals, if equipped, positions will not bestoredor
recalled when using the easy exit seatfunction.
The seat position can be saved foruptotwodrivers.
To store the easy exit seat position:
1. Press and release the 1 or 2 button of the memory
control for less than three seconds. The seat will
move to the stored memory position.
2. Adjust the seat to the desired exit position.
3. Press and hold the easy exit seat button for more
than three seconds. A double chime will sound to
let you know that the position has been stored
for the selected button 1 or 2.
To repeat the procedure for a second driver, follow
the preceding steps, but press the other numbered
memory control button.
To recall the easy exit seat position:
• Press the easy exit seat button on the memory
control while the vehicle is in (P) Park. The seat
will move to the stored exit position.
• Or, if the easy exit seat feature is activated in the
Driver Information Center (DIC), removing the key
from the ignition will move the seat to the exit
position. See “Easy Exit Seat” under DIC VehicleCustomization on page 3-56 for more information
on activating this feature in the DIC.
If an easy exit seat position has not been stored, the
default position is all the way rearward.
1-6
Reclining Seatbacks
Manual Reclining Seatbacks
{ CAUTION:
You can lose control of the vehicle if you try to
adjust a manual driver’s seat while the vehicle is
moving. The sudden movement could startle and
confuse you, or make you push a pedal when you
do not want to. Adjust the driver’s seat only when
the vehicle is not moving.
If the seats have manual reclining seatbacks, the lever
used to operate them is located on the outboard
side of the seat(s).
{ CAUTION:
If either seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there. Always
push and pull on the seatbacks to be sure they
are locked.
To recline the seatback, do the following:
1. Lift the recline lever.
2. Move the seatback to the desired position, then
release the lever to lock the seatback in place.
3. Push and pull on the seatback to make sure it is
locked.
1-7
To return the seatback to an upright position, do the
following:
1. Lift the lever fully without applying pressure to the
seatback and the seatback will return to the upright
position.
2. Push and pull on the seatback to make sure it is
locked.
Power Reclining Seatbacks
If your seats have power
reclining seatbacks, use
the vertical power seat
control located on the
outboard side of the
seat(s).
• To recline the seatback, press the controltowardthe
rear of the vehicle.
• To raise the seatback, press the controltowardthe
front of the vehicle.
1-8
{ CAUTION:
Sitting in a reclined position when your vehicle is
in motion can be dangerous. Even if you buckle
up, your safety belts cannot do their job when you
are reclined like this.
The shoulder belt cannot do its job. In a crash,
you could go into it, receiving neck or other
injuries.
The lap belt cannot do its job either. In a crash the
belt could go up over your abdomen. The belt
forces would be there, not at your pelvic bones.
This could cause serious internal injuries.
For proper protection when the vehicle is in
motion, have the seatback upright. Then sit well
back in the seat and wear your safety belt
properly.
Do not have a seatback reclined if your vehicle is
moving.
1-9
Head Restraints
Adjust the head restraint so that the top of the restraint
is at the same height as the top of the occupant’s
head. This position reduces the chance of a neck injury
in a crash.
Pull the head restraint up
to raise it.
To lower the head restraint, press thebutton,located
on the top of the seatback, andpushthehead
restraint down.
1-10
Rear Seats
Rear Seat Operation
Your vehicle has flip and fold second row seats which
provide additional cargo space.
To flip and fold the seat(s), do the following:
1. Pull up on the loop located where the seat cushion
meets the seatback and flip the seat cushion
forward.
Notice: Folding a rear seat with the safety belts
still fastened may cause damage to the seat or
the safety belts. Always unbuckle the safety belts
and return them to their normal stowed position
before folding a rear seat.
2. Lift the lever, located
on the outboard side
of the seatback,
and fold the seatback
forward.
The head restraint will automatically fold out of the
way as the seatback is folded down.
1-11
To return the seat(s) to the original position, do the
following:
{ CAUTION:
If either seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there. Always
push and pull on the seatbacks to be sure they
are locked.
1. Lift the seatback until it locks into the upright
position. Push and pull on the seatback to
make sure it is locked.
2. Return the head restraints to the upright position by
reaching behind the seat and pulling it forward until
it locks into place. Push and pull on the head
restraint to make sure that it is locked.
3. Flip the seat cushion back into place.
1-12
Safety Belts
Safety Belts: They Are for Everyone
This section of the manual describes how to use
safety belts properly. It also describes some things not
to do with safety belts.
{ CAUTION:
{ CAUTION:
It is extremely dangerous to ride inacargoarea,
inside or outside of a vehicle. Inacollision,people
riding in these areas are more likelytobeseriously
injured or killed. Do not allow peopletorideinany
area of your vehicle that is notequippedwithseats
and safety belts. Be sure everyone inyourvehicleis
in a seat and using a safetybeltproperly.
Do not let anyone ride where asafetybeltcannot
be worn properly. In a crash, ifyouoryour
passenger(s) are not wearing safety belts, the
injuries can be much worse. You canhitthings
inside the vehicle harder or be ejectedfromthe
vehicle. You and your passenger(s) can be
seriously injured or killed. In the samecrash,you
might not be, if you are buckledup.Alwaysfasten
your safety belt, and check that yourpassenger(s)
are restrained properly too.
This vehicle has indicators as a reminder to buckle the
safety belts. See Safety Belt Reminders on page 3-31
for additional information.
1-13
In most states and in all Canadian provinces, the law
requires wearing safety belts. Here is why:
You never know if you will be in a crash. If you do have
a crash, you do not know if it will be a serious one.
A few crashes are mild, and some crashes can be
so serious that even buckled up, a person would not
survive. But most crashes are in between. In many
of them, people who buckle up can survive and
sometimes walk away. Without safety belts, they
could have been badly hurt or killed.
After more than 40 years of safety belts in vehicles,
the facts are clear. In most crashes buckling up does
matter... a lot!
Why Safety Belts Work
When you ride in or on anything, you go as fast as
it goes.
Take the simplest vehicle. Suppose it is just a seat on
wheels.
1-14
Put someone on it.Get it up to speed. Then stop the vehicle. The rider
does not stop.
1-15
The person keeps going until stopped by something. In
a real vehicle, it could be the windshield...
1-16
or the instrument panel...
or the safety belts!
With safety belts, you slow down as the vehicle does.
You get more time to stop. You stop over more distance,
and your strongest bones take the forces. That is why
safety belts make such good sense.
Questions and Answers About Safety
Belts
Q: Will I be trapped in the vehicle after a crash if I
am wearing a safety belt?
A: You could be — whether you are wearing a safety
belt or not. But your chance of being conscious
during and after an accident, so you can unbuckle
and get out, is much greater if you are belted.
And you can unbuckle a safety belt, even if you are
upside down.
Q: If my vehicle has airbags, why should I have to
wear safety belts?
A: Airbags are supplemental systems only; so they
work with safety belts — not instead of them.
Whether or not an airbag is provided, all occupants
still have to buckle up to get the most protection.
That is true not only in frontal collisions, but
especially in side and other collisions.
1-17
Q: If I am a good driver, and I never drive far from
home, why should I wear safety belts?
A: You may be an excellent driver, but if you are in a
crash — even one that is notyourfault—youand
your passenger(s) can be hurt. Being agooddriver
does not protect you from things beyondyour
control, such as bad drivers.
Most accidents occur within 25 miles (40 km) of
home. And the greatest number of serious injuries
and deaths occur at speeds of less than 40 mph
(65 km/h).
Safety belts are for everyone.
How to Wear Safety Belts Properly
This section is only for people of adult size.
Be aware that there are special things to know about
safety belts and children. And there are different
rules for smaller children and infants. If a child will be
riding in the vehicle, see Older Children on page 1-32
or Infants and Young Children on page 1-35. Follow
those rules for everyone’s protection.
It is very important for all occupants to buckle up.
Statistics show that unbelted people are hurt more often
in crashes than those who are wearing safety belts.
Occupants who are not buckled up can be thrown out of
the vehicle in a crash. And they can strike others in
the vehicle who are wearing safety belts.
First, before you or your passenger(s) wear a safety
belt, there is important information you should know.
1-18
Sit up straight and always keep your feet on the floor in
front of you. The lap part of the belt should be worn
low and snug on the hips, just touching the thighs.
In a crash, this applies force to the strong pelvic bones
and you would be less likely to slide under the lap
belt. If you slid under it, the belt would apply force on
your abdomen. This could cause serious or even
fatal injuries. The shoulder belt should go over the
shoulder and across the chest. These parts of the
body are best able to take belt restraining forces.
The shoulder belt locks if there is a sudden stop or
crash.
1-19
Q: What is wrong with this?
A: The shoulder belt is too loose. It will not give as
much protection this way.
{ CAUTION:
You can be seriously hurt if your shoulder belt is
too loose. In a crash, you would move forward too
much, which could increase injury. The shoulder
belt should fit snugly against your body.
1-20
Q: What is wrong with this?
A: The lap belt is too loose. It will not give nearly as
much protection this way.
{ CAUTION:
You can be seriously hurt if your lap belt is too
loose. In a crash, you could slide under the lap
belt and apply force on your abdomen. This could
cause serious or even fatal injuries. The lap belt
should be worn low and snug on the hips, just
touching the thighs.
1-21
Q: What is wrong with this?
A: The belt is buckled in the wrong buckle.
{ CAUTION:
You can be seriously injured if your belt is buckled
in the wrong place like this. In a crash, the belt
would go up over your abdomen. The belt forces
would be there, not on the pelvic bones. This
could cause serious internal injuries. Always
buckle your belt into the buckle nearest you.
1-22
Q: What is wrong with this?
A: The belt is over an armrest.
{ CAUTION:
You can be seriously injured if your belt goes over
an armrest like this. The belt would be much too
high. In a crash, you can slide under the belt. The
belt force would then be applied on the abdomen,
not on the pelvic bones, and that could cause
serious or fatal injuries. Be sure the belt goes
under the armrests.
1-23
Q: What is wrong with this?
A: The shoulder belt is worn under the arm. It should
be worn over the shoulder at all times.
{ CAUTION:
You can be seriously injured if you wear the
shoulder belt under your arm. In a crash, your
body would move too far forward, which would
increase the chance of head and neck injury. Also,
the belt would apply too much force to the ribs,
which are not as strong as shoulder bones. You
could also severely injure internal organs like your
liver or spleen. The shoulder belt should go over
the shoulder and across the chest.
1-24
Q: What is wrong with this?
A: The belt is behind the body.
{ CAUTION:
You can be seriously injured by not wearing the
lap-shoulder belt properly. In a crash, you would
not be restrained by the shoulder belt. Your body
could move too far forward increasing the chance
of head and neck injury. You might also slide
under the lap belt. The belt force would then be
applied right on the abdomen. That could cause
serious or fatal injuries. The shoulder belt should
go over the shoulder and across the chest.
1-25
Q: What is wrong with this?
A: The belt is twisted across the body.
{ CAUTION:
You can be seriously injured by a twisted belt. In a
crash, you would not have the full width of the belt
to spread impact forces. If a belt is twisted, make
it straight so it can work properly, or ask your
dealer/retailer to fix it.
1-26
Loading...
+ 454 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.