Chevrolet Captiva 2009 User Manual

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1876598

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=1876598&pubCellSyskey=940&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Specifications

| Document ID: 1876598

|

Brakes

|

Antilock Brake System

|

Fastener Tightening Specifications

Application

Brake Pressure Modulator Valve Bracket Bolts 10 N·m 89 lb in Brake Pressure Modulator Valve Bracket Nut 10 N·m 89 lb in Brake Pressure Modulator Valve Bolt 10 N·m 89 lb in Brake Pipe Fittings 21 N·m 16 lb ft Electronic Brake Control Module (EBCM) to Brake Pressure Modulator Valve

Bolts Wheel Speed Sensor Bolt 8 N·m 71 lb in Yaw Rate Sensor Bolts 8 N·m 71 lb in

Specification

Metric English

3 N·m 27 lb in

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2079529

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2079529&from=sm

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Schematic and Routing Diagrams

| Document ID: 2079529

|

Brakes

|

Antilock Brake System

Control Module, Instrument Panel Display and Serial Data

|

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2079531

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2079531&from=sm

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Schematic and Routing Diagrams

| Document ID: 2079531

|

Brakes

Wheel Speed and YAW/Lateral Speed Sensors

|

Antilock Brake System

|

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 2165370

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2165370&pubCellSyskey=1238&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2165370

|

Brakes

|

Antilock Brake System

|

Antilock Brake System Automated Bleed Procedure

Warning: Refer to Brake Fluid Irritant Warning in the Preface section.

Caution: Refer to Brake Fluid Effects on Paint and Electrical Components Caution in the Preface

section.

Note: Before performing the antilock brake system (ABS) Automated Bleed Procedure, first perform a manual or pressure bleed of the base brake system. Refer to Hydraulic Brake System

Bleeding. The automated bleed procedure is recommended when one of the following conditions

exist:

• Base brake system bleeding does not achieve the desired pedal height or feel

• Extreme loss of brake fluid has occurred

• Air ingestion is suspected in the secondary circuits of the brake modulator assembly

The ABS Automated Bleed Procedure uses a scan tool to cycle the system solenoid valves and run the pump in order to purge any air from the secondary circuits. These circuits are normally closed off, and are only opened during system initialization at vehicle start up and during ABS operation. The automated bleed procedure opens these secondary circuits and allows any air trapped in these circuits to flow out toward the brake corners.

Automated Bleed Procedure

Caution: The Auto Bleed Procedure may be terminated at any time during the process by

pressing the EXIT button. No further Scan Tool prompts pertaining to the Auto Bleed procedure will be given. After exiting the bleed procedure, relieve bleed pressure and disconnect bleed equipment per manufacturers instructions. Failure to properly relieve pressure may result in spilled brake fluid causing damage to components and painted surfaces.

1. Raise and support the vehicle. Refer to Lifting and

2. Remove all 4 tire and wheel assemblies. Refer to Tire and Wheel Removal and Installation.

3. Inspect the brake system for leaks and visual damage. Refer to Symptoms - Hydraulic

Brakes. Repair or replace components as needed.

4. Lower the vehicle.

5. Inspect the battery state of charge. Refer to Battery Inspection/Test.

6. Install a scan tool.

7. Turn the ignition ON, with the engine OFF.

8. With the scan tool, establish communications with the ABS system. Select Special Functions. Select Automated Bleed from the Special Functions menu.

9. Raise and support the vehicle. Refer to Lifting and

10. Following the directions given on the scan tool, pressure bleed the base brake system. Refer to Hydraulic

11. Follow the scan tool directions until the desired brake pedal height is achieved.

12. If the bleed procedure is aborted, a malfunction exists. Perform the following steps before resuming the bleed procedure:

• If a DTC is detected, refer to Diagnostic Trouble Code (DTC) List - Vehicle and diagnose the appropriate DTC.

• If the brake pedal feels spongy, perform the conventional brake bleed procedure again.

Brake System Bleeding.

Jacking the Vehicle.

Refer to Hydraulic

Page

2

of 2Document ID: 2165370

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2165370&pubCellSyskey=1238&pubObj

...

13. When the desired pedal height is achieved, press the brake pedal to inspect for firmness.

14. Lower the vehicle.

15. Remove the scan tool.

16. Install the tire and wheel assemblies. Refer to Tire and

17. Inspect the brake fluid level. Refer to Master Cylinder Reservoir Filling.

18. Road test the vehicle while inspecting that the pedal remains high and firm.

Brake System Bleeding.

Wheel Removal and Installation.

2009 Saturn VUE - AWD

performed. Some of these procedures are as

Page

1

of 1Document ID: 1998897

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=1998897&pubCellSyskey=1627&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 1998897

|

Brakes

|

Antilock Brake System

|

Steering Angle Sensor Centering

The steering angle sensor does not require centering often. Centering of the steering angle sensor might be required after certain service procedures are follows:

• Steering gear replacement

• Steering column replacement

• Steering angle sensor replacement

• Intermediate shaft replacement

• Electronic brake control module (EBCM) replacement

• Collision or other physical damage

The steering angle sensor centering procedure can be completed with a scan tool using the following steps:

1. Using the steering wheel, align the front wheels forward.

2. Set the transmission in the PARK position.

3. Turn the ignition switch ON, with the engine OFF.

4. Clear any DTCs that may be set.

5. Select Steering Angle Sensor Centering in the EBCM Special Functions list.

6. Follow the scan tool directions to complete the centering procedure.

2009 Saturn VUE - AWD

Page

1

of 4Document ID: 2167671

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167671&pubCellSyskey=954&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2167671

|

Brakes

|

Antilock Brake System

Electronic Brake Control Module Replacement (Except

|

Hybrid)

Removal Procedure

Warning: Refer to Brake Fluid Irritant Warning in the Preface section.

Caution: Refer to Brake Fluid Effects on Paint and Electrical Components Caution in the Preface

section.

Caution: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM with the ignition switch in the OFF position. Failure to observe this precaution could result in damage to the EBCM/EBTCM.

1. Place the ignition switch in the OFF position.

2. Remove the underhood electrical center. Refer to Underhood

Block Replacement.

3. Without draining the coolant or removing the hoses, remove and position aside the radiator surge tank. Refer to Radiator Surge Tank Replacement.

4. Clean the electronic brake control module (EBCM) to brake pressure modulator valve (BPMV) area of any dirt or debris.

5. Disconnect the EBCM electrical connector by lifting the locking lever upward.

6. Disconnect the LF brake pipe fitting (1) from the BPMV.

Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.

7. Carefully position aside and secure the brake pipe to provide clearance for removal of the

Electrical Center or Junction

EBCM.

Page

2

of 4Document ID: 2167671

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167671&pubCellSyskey=954&pubObj

...

8. Remove the 4 EBCM bolts (1).

9. Carefully pull the EBCM (1) from the BPMV.

Do not pry the components apart.

10. Remove the 12 EBCM seals, if necessary.

Installation Procedure

Page

3

of 4Document ID: 2167671

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167671&pubCellSyskey=954&pubObj

...

1. Install the EBCM seals, if removed.

2. Install the EBCM (1) to the BPMV.

Caution: Refer to Fastener Caution

3. Install the 4 EBCM bolts (1) and tighten the bolts in a cross pattern to 3 N·m (27 lb in).

in the Preface section.

Electrical Center or Junction Block

Page

4

of 4Document ID: 2167671

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167671&pubCellSyskey=954&pubObj

...

4. Position the LF brake pipe to the BPMV.

5. Connect the LF brake pipe fitting (1) to the BPMV and tighten to 21 N·m (16 lb ft).

6. Install the radiator surge tank. Refer to Radiator

7. Install the underhood electrical center. Refer to Underhood

Replacement.

8. If installing a new EBCM, program the EBCM. Refer to Control Module References.

9. Without starting the engine, place the ignition switch in the ON position.

10. Perform the Diagnostic

11. Observe the feel of the brake pedal after performing the diagnostic system check. If the pedal now feels spongy, air may have been in the secondary circuit of the brake modulator assembly, which may have been introduced into the primary circuit.

System Check - Vehicle.

Surge Tank Replacement.

If the pedal feels spongy, perform the Antilock

Brake System Automated Bleed Procedure.

2009 Saturn VUE - AWD

Page

1

of 7Document ID: 2167704

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167704&pubCellSyskey=1189&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2167704

|

Brakes

|

Antilock Brake System

Brake Pressure Modulator Valve Replacement (Except

|

Hybrid)

Removal Procedure

Warning: Refer to Brake Fluid Irritant Warning in the Preface section.

Caution: Refer to Brake Fluid Effects on Paint and Electrical Components Caution in the Preface

section.

Caution: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM with the ignition switch in the OFF position. Failure to observe this precaution could result in damage to the EBCM/EBTCM.

1. Turn the ignition switch to the OFF position.

2. Remove the underhood electrical center. Refer to Underhood

Block Replacement.

3. Without draining the coolant or removing the hoses, remove and position aside the radiator surge tank. Refer to Radiator Surge Tank Replacement.

Electrical Center or Junction

4. Disconnect the electronic brake control module (EBCM) electrical connector by lifting the locking tabs.

5. Disconnect the LF brake pipe fitting (1) at the brake pressure modulator valve (BPMV).

Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.

6. Disconnect the RF brake pipe fitting (2) from the BPMV.

Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and

Page

2

of 7Document ID: 2167704

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167704&pubCellSyskey=1189&pubObj

...

contamination.

7. Disconnect the master cylinder primary brake pipe fitting (1) from the BPMV.

Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.

8. Disconnect the master cylinder secondary brake pipe fitting (2) from the BPMV.

Cap the brake pipe fitting and plug the BPMV inlet port to prevent brake fluid loss and contamination.

Page

3

of 7Document ID: 2167704

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167704&pubCellSyskey=1189&pubObj

...

9. Disconnect the LR brake pipe fitting (1) from the BPMV.

Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.

10. Disconnect the RR brake pipe fitting (2) from the BPMV.

Cap the brake pipe fitting and plug the BPMV outlet port to prevent brake fluid loss and contamination.

11. Remove the BPMV bolt (1).

Page

4

of 7Document ID: 2167704

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167704&pubCellSyskey=1189&pubObj

...

12. Carefully remove the BPMV assembly (1) by pulling straight upward.

Do not pry on the accumulator caps on the underside of the BPMV.

13. Inspect the insulators for damage and replace, if necessary.

Installation Procedure

1. Install the BPMV assembly (1) to the bracket.

Caution: Refer to Fastener Caution

in the Preface section.

Page

5

of 7Document ID: 2167704

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167704&pubCellSyskey=1189&pubObj

...

2. Install the BPMV bolt (1) and tighten to 10 N·m (89 lb in).

3. Connect the LR brake pipe fitting (1) to the BPMV and tighten to 21 N·m (16 lb ft).

4. Connect the RR brake pipe fitting (2) to the BPMV and tighten to 21 N·m (16 lb ft).

Electrical Center or Junction Block

Page

6

of 7Document ID: 2167704

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167704&pubCellSyskey=1189&pubObj

...

5. Connect the master cylinder primary brake pipe fitting (1) to the BPMV and tighten to 21 N·m (16 lb ft).

6. Connect the master cylinder secondary brake pipe fitting (2) to the BPMV and tighten to 21 N·m (16 lb ft).

7. Connect the LF brake pipe fitting (1) to the BPMV and tighten to 21 N·m (16 lb ft).

8. Connect the RF brake pipe fitting (2) to the BPMV and tighten to 21 N·m (16 lb ft).

9. Connect the EBCM electrical connector.

10. Install the radiator surge tank. Refer to Radiator

11. Install the underhood electrical center. Refer to Underhood

Replacement.

12. Bleed the hydraulic brake system. Refer to Hydraulic

13. Turn the ignition switch to the ON position.

14. Perform the Diagnostic System Check - Vehicle.

15. Observe the brake pedal feel after performing the diagnostic system check. If the pedal now

Surge Tank Replacement.

Brake System Bleeding.

feels spongy, air may have been in, or may have been introduced into the primary circuit.

Page

7

of 7Document ID: 2167704

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167704&pubCellSyskey=1189&pubObj

...

If the pedal feels spongy, perform the Antilock Brake System Automated Bleed Procedure.

2009 Saturn VUE - AWD

Page

1

of 4Document ID: 2167744

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167744&pubCellSyskey=1190&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2167744

|

Brakes

|

Antilock Brake System

Brake Pressure Modulator Valve Bracket Replacement

|

(Except Hybrid)

Removal Procedure

1. Place the ignition switch in the OFF position.

2. Remove the underhood electrical center. Refer to Underhood

Block Replacement.

3. Without draining the coolant or removing the hoses, remove and position aside the radiator surge tank. Refer to Radiator Surge Tank Replacement.

Electrical Center or Junction

4. Remove the brake pressure modulator valve (BPMV) bolt (1).

Page

2

of 4Document ID: 2167744

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167744&pubCellSyskey=1190&pubObj

...

5. Without disconnecting the brake pipe fittings, carefully lift the BPMV assembly (1) upward to release the mounting pins from the BPMV bracket insulators.

Do not pry on the accumulator caps on the underside of the BPMV.

6. Position the BPMV assembly aside and secure with heavy mechanics wire or equivalent.

7. Remove the 2 BPMV bracket bolts (1).

8. Remove the BPMV bracket nut (1) and the BPMV bracket.

9. Inspect the insulators for damage and replace, if necessary.

Installation Procedure

Page

3

of 4Document ID: 2167744

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167744&pubCellSyskey=1190&pubObj

...

1. Install the BPMV bracket.

2. Loosely install the BPMV bracket nut (1).

Caution: Refer to Fastener Caution

3. Install the 2 BPMV bracket bolts (1) and tighten to 10 N·m (89 lb in).

4. Tighten the BPMV bracket nut to 10 N·m (89 lb in).

in the Preface section.

Electrical Center or Junction Block

Page

4

of 4Document ID: 2167744

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167744&pubCellSyskey=1190&pubObj

...

5. Carefully position the BPMV assembly (1) to the BPMV bracket insulators.

6. Install the BPMV bolt (1) and tighten to 10 N·m (89 lb in).

7. Install the radiator surge tank. Refer to Radiator

8. Install the underhood electrical center. Refer to Underhood

Replacement.

Surge Tank Replacement.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2158259

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2158259&pubCellSyskey=1415&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2158259

|

Brakes

|

Antilock Brake System

|

Front Wheel Speed Sensor Replacement

Callout Component Name

Warning: Refer to Brake Dust Warning in the Preface section.

Preliminary Procedures

1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.

2. Remove the tire and wheel. Refer to Tire

3. Remove the brake rotor. Refer to Front Brake Rotor Replacement. Wheel Speed Sensor Electrical Connector

1

Procedure

Release the electrical connector from the bracket. Wheel Speed Sensor Bolt

Caution: Refer to Fastener Caution in the Preface section.

2

Tighten 8 N·m (71 lb in)

Wheel Speed Sensor

3

Procedure

Route the wheel speed sensor electrical harness through the splash shield.

and Wheel Removal and Installation.

2009 Saturn VUE - AWD

information display assembly can not

Page

1

of 1Document ID: 1873589

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=1873589&pubCellSyskey=1056&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 1873589

|

Brakes

|

Antilock Brake System

|

Electronic Traction Control Switch Replacement

The electronic traction control switch (1) located in the driver be serviced separately. Should the switch assembly need to be replaced, the entire driver information display assembly will need to be replaced. Refer to Driver Information Display Switch

Replacement .

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 2167745

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167745&pubCellSyskey=1243&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2167745

|

Brakes

|

Antilock Brake System

|

Vehicle Yaw Sensor Replacement

Callout Component Name

Warning: Refer to SIR Warning in the Preface section.

Preliminary Procedures

1. Disable the SIR system. Refer to SIR Disabling and Enabling.

2. Remove front floor rear console. Refer to Front

Electronic Brake Control Vehicle Yaw Sensor Bolt (Qty: 2)

1

Caution: Refer to Fastener Caution in the Preface section.

Tighten

8 N·m (71 lb ft) Electronic Brake Control Vehicle Yaw Sensor Assembly

Floor Console Replacement.

Procedure

2

1. Remove the console bracket and bolts.

2. Position the wire harness assembly out of the way.

3. Disconnect any electrical connectors.

4. Transfer components as needed.

Page

2

of 2Document ID: 2167745

12/1/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167745&pubCellSyskey=1243&pubObj

...

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1749013

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1749013&pubCellSyskey=9265&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Specifications

|

Body Repair

| Document ID: 1749013

|

Fastener Tightening Specifications

Application

Fuel Filler Door Bolts 2.5 N·m 22 lb in Front Door Check Link Bolts 10 N·m 89 lb in Front Door Check Link to Body 20 N·m 15 lb ft Front Door Hinge To Body Bolts 36 N·m 27 lb ft Front Door Hinge To Door Bolts 25 N·m 18 lb ft Front Fender Bolts 9 N·m 80 lb in Front Outer Door Panel Bolts 8 N·m 71 lb in Hood Hinge Bolts 25 N·m 18 lb ft Hood Latch Bolts 10 N·m 89 lb in Liftgate Hinge Bolts 25 N·m 18 lb ft Liftgate Hinge Nuts 25 N·m 18 lb ft Liftgate Strut Anchor 25 N·m 18 lb ft Quarter Panel Bolts 9 N·m 80 lb in Quarter Panel Nuts 9 N·m 80 lb in Rear Door Check Link Bolts 10 N·m 89 lb in Rear Door Check Link to Body Bolt 20 N·m 15 lb ft Rear Door Hinge To Body Bolts 36 N·m 27 lb ft Rear Door Hinge To Door Bolts 25 N·m 18 lb ft Rear Outer Door Panel Bolts 8 N·m 71 lb in Hood Latch Release Cable Bolt 9 N·m 80 lb in Fuel Tank Filler Door Bolt 2.5 N·m 22 lb in Hood Latch Release Handle Screw 10 N·m 89 lb in

Specification

Metric English

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 2166688

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166688&pubCellSyskey=9286&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166688

|

Hood Primary Latch Release Cable Replacement

Callout

Component Name

Preliminary Procedures

1. Remove the headlamps. Refer to Headlamp Replacement.

2. Remove the hood release handle. Refer to Hood

Replacement.

3. Remove the front compartment front sight shield. Refer to Front Compartment Sight

Shields Replacement.

Hood Latch Release Cable Bolt (Qty: 2)

Caution: Refer to Fastener Caution in the Preface section.

1

Tighten 9 N·m (80 lb in)

Hood Latch Release Cable

Procedure

2

1. Disconnect the hood release cable from the hood latch by squeezing the hood release cable retainer.

Primary Latch Release Cable Handle

2. Attach mechanic's wire to the existing cable to ease installation of the new

Page

2

of 2Document ID: 2166688

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166688&pubCellSyskey=9286&pubO

...

cable.

3. Release the cable from the latch assembly and pull through the dash panel.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166693

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166693&pubCellSyskey=149890&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166693

|

Front Side Door Adjustment

Warning: In order to prevent SIR deployment, personal injury, or unnecessary SIR system

repairs, do not strike the door or the door pillar in the area of the side impact sensor (SIS). Turn OFF the ignition and remove the key when performing service in the area of the SIS.

1. Remove the door lock striker. Refer to Front Side Door Lock Striker Replacement.

2. For up, down, forward, or rearward adjustment, loosen the hinge to hinge pillar bolts.

3. Move the door within the door opening to achieve the best alignment and operation.

Caution: Refer to Fastener Caution

4. Tighten all of the hinge fasteners that were loosened.

Tighten Tighten the hinge fasteners to 25 N·m (18 lb ft).

5. Install the striker to the approximate proper position.

6. Adjust the door striker. Refer to Front Side

7. Inspect the door weatherstrips for proper fit.

in the Preface section.

Door Lock Striker Adjustment.

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 2166698

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166698&pubCellSyskey=149891&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166698

|

Front Side Door Replacement

Callout

Component Name

Preliminary Procedures

1. Disable the supplemental inflatable restraint (SIR) system. Refer to SIR Disabling and

Enabling.

2. Remove the front door trim panel. Refer to Front Side Door Trim Panel Replacement.

3. Remove front door check link bolt. Refer to Front Side Door Check Link Replacement.

Front Side Door Bolt (Qty: 4)

Caution: Refer to Fastener Caution in the Preface section.

1

Tighten 25 N·m (18 lb ft)

Front Side Door

Procedure

2

1. Remove the water deflector.

2. Support the door before removing the hinge bolts.

3. Disconnect the electrical connector, if equipped.

4. With the aid of an assistant, remove the door.

Page

2

of 2Document ID: 2166698

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166698&pubCellSyskey=149891&pub

...

5. If installing new door, transfer all necessary components.

6. Verify door is properly aligned. If door adjustments are needed, refer to Front

Side Door Adjustment.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166700

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166700&pubCellSyskey=149894&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166700

|

Rear Side Door Adjustment

Warning: In order to prevent SIR deployment, personal injury, or unnecessary SIR system

repairs, do not strike the door or the door pillar in the area of the side impact sensor (SIS). Turn OFF the ignition and remove the key when performing service in the area of the SIS.

1. Remove the door striker. Refer to Rear Side Door Lock Striker Replacement.

2. For up, down, forward, or rearward adjustment, loosen the hinge to hinge pillar bolts.

3. Move the door within the door opening to achieve the best alignment and operation.

Caution: Refer to Fastener Caution

4. Tighten all of the hinge fasteners that were loosened.

Tighten Tighten the hinge fasteners to 25 N·m (18 lb ft).

5. Install the striker to the approximate proper position.

6. Adjust the door striker. Refer to Rear Side

7. Inspect the door weatherstrips for proper fit.

in the Preface section.

Door Lock Striker Adjustment.

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 2166707

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166707&pubCellSyskey=149904&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166707

|

Rear Side Door Replacement

Callout

Warning: Refer to SIR Warning in the Preface section.

Component Name

Preliminary Procedures

1. Disable the supplemental inflatable restraint (SIR) system. Refer to SIR Disabling and

Enabling.

2. Remove the rear door trim panel. Refer to Rear Side Door Trim Panel Replacement.

3. Remove rear side door check link. Refer to Rear Side Door Check Link Replacement.

Rear Side Door Bolt (Qty: 4)

Caution: Refer to Fastener Caution in the Preface section.

1

Tighten 25 N·m (18 lb ft)

Rear Side Door Assembly

Procedure

1. Remove the water deflector.

2

Page

2

of 2Document ID: 2166707

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166707&pubCellSyskey=149904&pub

...

2. Support the door before removing the hinge bolts.

3. Disconnect the electrical connector, if equipped.

4. With the aid of an assistant, remove the door.

5. If installing new door, transfer all necessary components.

6. Verify door is properly aligned. If door adjustments are needed, refer to Rear

Door Adjustment.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166711

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166711&pubCellSyskey=9344&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166711

|

Front Fender Replacement

Callout Component Name

Preliminary Procedures

1. Remove the bumper fascia. Refer to Front Bumper Fascia Replacement.

2. Remove Front Fender Wheel Opening Molding. Refer to Front

Molding Replacement.

3. Remove the wheelhouse liner. Refer to Front Wheelhouse Liner Replacement.

4. Remove the rocker panel molding. Refer to Rocker Panel Molding Replacement.

5. Remove the front fender center molding. Refer to Front Fender Center Molding

Replacement.

Front Fender Bolt (Qty: 9)

1

2 Front Fender

Caution: Refer to Fastener Caution in the Preface section.

Tighten

9 N·m (80 lb in)

Fender Wheel Opening

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166716

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166716&pubCellSyskey=149980&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166716

|

Liftgate Adjustment

1. Note the original position of the liftgate latch striker.

2. Remove the striker.

3. Loosen the hinge-to-roof panel bolts for forward or rearward adjustments.

4. If Adjusting hinge to roof panel Bolts. Lower Rear And Headliner if as needed.

5. Loosen the liftgate-to-hinge bolts for up and down adjustment.

6. Move the liftgate within the liftgate opening to achieve the best alignment and operation.

7. Install striker to approximately the proper position.

8. Adjust the striker to achieve the best operation and alignment of the liftgate.

9. Inspect the seals for proper engagement.

Caution: Refer to Fastener Caution

10. Tighten the bolts when the proper adjustment is achieved.

Tighten Tighten the bolts to 25 N·m (18 lb ft).

in the Preface section.

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 2166720

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166720&pubCellSyskey=149981&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166720

|

Liftgate Replacement

Callout Component Name

Warning: When a lift gate hold open device is being removed or installed, provide alternate

support to avoid the possibility of damage to the vehicle or personal injury.

Preliminary Procedures

1. Disconnect the strut rods. Refer to Liftgate Strut Replacement.

2. Remove the rear door upper garnish molding. Refer to Liftgate Garnish Molding

Replacement.

Liftgate Body Side Hinge Bolt (Qty: 4)

1

2

Caution: Refer to Fastener Caution in the Preface section.

Tighten

25 N·m (18 lb ft) Liftgate

Procedure

1. Disconnect the electrical connector.

2. Transfer part as needed.

Page

2

of 2Document ID: 2166720

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166720&pubCellSyskey=149981&pub

...

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166725

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166725&pubCellSyskey=9379&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

| Document ID: 2166725

|

Body Repair

|

Hood Primary Latch Release Cable Handle Replacement

Callout Component Name

Hood Latch Release Handle Screw (Qty: 2)

1

2

Caution: Refer to Fastener Caution in the Preface section.

Tighten

10 N·m (89 lb in) Hood Latch Release Handle

Tip To release the handle, pull down the cable and unhook from the handle.

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 2166731

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166731&pubCellSyskey=149997&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

| Document ID: 2166731

|

Body Repair

Front Side Door Upper Hinge and Lower Hinge

|

Replacement

Callout

Component Name

Preliminary Procedures

1. Remove front fender. Refer to Front Fender Replacement.

2. Remove front door. Refer to Front

3. Remove the insulator pad between the fender and the hinge pillar to remove bolts.

Front Side Door Hinge to Body Bolt (Qty: 4)

Caution: Refer to Fastener Caution in the Preface section.

1

Tighten 36 N·m (26 lb ft)

Front Side Door Hinge Assembly

Side Door Replacement.

Procedure

1. If installing new door, transfer all necessary components.

2. Verify door is properly aligned. If door adjustments are needed, refer to Front

Side Door Adjustment.

Page

2

of 2Document ID: 2166731

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166731&pubCellSyskey=149997&pub

...

Tip Support the door during procedure.

2

Use a soft marker to outline around the outside of hinge for install purposes.

When re-installing door, align hinge with marks made during removal procedures.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166732

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166732&pubCellSyskey=9274&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166732

|

Hood Hinge Replacement

Callout Component Name

Preliminary Procedures

1. Remove the hood. Refer to Hood Replacement.

2. Remove the front fender. Refer to Front

Hood Hinge Bolt (Qty: 4)

1

2

Caution: Refer to Fastener Caution in the Preface section.

Tighten

25 N·m (18 lb ft) Hood Hinge

Tip Adjust the hood hinge, if needed. Refer to Hood Adjustment.

Fender Replacement.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166750

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166750&pubCellSyskey=150000&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166750

|

Liftgate Hinge Replacement

Callout Component Name

Preliminary Procedures

1. Remove the liftgate. Refer to Liftgate Replacement.

2. Drop the rear of the headliner to access the bolts. Refer to headliner replacement.

Headlining

3. Use a grease pencil to mark the liftgate hinge position to the body prior to removal.

1

Trim Panel Replacement.

Liftgate Hinge Nut (Qty: 2)

Caution: Refer to Fastener Caution in the Preface section.

Tighten

25 N·m (18 lb ft) Liftgate Hinge

Procedure

2

• Adjust the liftgate, if needed. Refer to Liftgate Adjustment.

• Inspect the hinge gasket and replace if damaged or torn.

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 2166756

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166756&pubCellSyskey=150006&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

| Document ID: 2166756

|

Body Repair

Rear Side Door Upper Hinge and Lower Hinge

|

Replacement

Removal Procedure

Warning: In order to prevent SIR deployment, personal injury, or unnecessary SIR system

repairs, do not strike the door or the door pillar in the area of the side impact sensor (SIS). Turn OFF the ignition and remove the key when performing service in the area of the SIS.

1. Mark around the hinge location with a soft marker for installation alignment purposes.

2. Support the door.

3. With the door fully latched on the striker, remove the hinge to door bolts.

4. Remove the hinge to body bolts and remove the hinges one at a time.

Installation Procedure

Page

2

of 2Document ID: 2166756

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166756&pubCellSyskey=150006&pub

...

1. Position the hinge to the vehicle with the marks made prior to removal.

Caution: Refer to Fastener Caution in the Preface section.

2. Install the hinge to door bolts.

Tighten Tighten the bolts to 25 N·m (18 lb ft).

3. Install the hinge to body bolts.

Tighten Tighten the bolts to 36 N·m (27 lb ft).

4. Inspect the door for proper alignment. Refer to Rear Door

Adjustment.

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 2150107

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2150107&pubCellSyskey=9276&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2150107

|

Hood Adjustment

1. Loosen the hinge-to-body bolts to adjust the hood fore and aft, and cross-vehicle. Position the hood as needed.

2. Adjust the hood latch and hood bumpers to adjust the hood up and down at the front of the hood.

Caution: Refer to Fastener Caution

in the Preface section.

3. Tighten the hinge and latch bolts.

Page

2

of 2Document ID: 2150107

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2150107&pubCellSyskey=9276&pubO

...

Tighten

• Tighten the hinge-to-hood bolts to 25 N·m (18 lb ft).

• Tighten the hinge-to-body bolts to 25 N·m (18 lb ft).

• Tighten the hood latch fastener to 25 N·m (18 lb ft).

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166759

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166759&pubCellSyskey=9271&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166759

|

Hood Replacement

Callout Component Name

Warning: When a hood hold open device is being removed or installed, provide alternate

support to avoid the possibility of damage to the vehicle or personal injury.

Preliminary Procedure

Disconnect the hood strut rod. Refer to Hood Strut Replacement.

Hood Hinge Bolt (Qty: 4)

1

2

Caution: Refer to Fastener Caution in the Preface section.

Tighten

25 N·m (18 lb ft) Hood

Tip

• Disconnect any electrical connectors before removing.

• Transfer any parts as needed.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1869774

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1869774&pubCellSyskey=9275&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 1869774

|

Hood Insulator Replacement

Callout Component Name

1 Hood Insulator Plastic Retainer (Qty: 11) 2 Hood Insulator

2009 Saturn VUE - AWD

center of the latch assembly

Page

1

of 1Document ID: 2135295

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2135295&pubCellSyskey=9284&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2135295

|

Hood Latch Adjustment

Inspection Procedure

1. Release the primary hood latch in order to inspect the operation of the pop-up spring.

2. Attempt to raise the hood while the hood is in the pop-up position.

• The hood should raise without the hood striker binding against the latch.

• The secondary latch should engage in order to prevent the hood from being raised.

Adjustment Procedure

1. Loosen the bolts retaining the hood latch to the support bracket.

Caution: Refer to Fastener Caution

2. Move the hood latch from side to side until the striker enters the and tighten to 10 N·m (89 lb in).

in the Preface section.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166761

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166761&pubCellSyskey=9318&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166761

|

Hood Primary and Secondary Latch Replacement

Callout

Component Name

Preliminary Procedure

Remove the front compartment sight shields. Refer to Front Compartment Sight Shields

Replacement.

Hood Latch Mounting Bolt (Qty: 3)

Caution: Refer to Fastener Caution in the Preface section.

1

Tighten 10 N·m (89 lb in)

Hood Latch Assembly

Procedure

2

1. Disconnect the remote start electrical connector, if equipped.

2. Disconnect the release cable from the hood latch by squeezing the cable retainer.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166765

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166765&pubCellSyskey=150018&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166765

|

Front Side Door Check Link Replacement

Callout Component Name

Preliminary Procedures

1. Remove the front door trim panel. Refer to Front Side Door Trim Panel Replacement.

2. Remove the water deflector. Front Side Door Check Link to Body Bolt

1

2

3

Caution: Refer to Fastener Caution in the Preface section.

Tighten

20 N·m (18 lb ft) Front Side Door Check Link Bolt (Qty: 2)

Tighten 7 N·m (62 lb in)

Front Side Door Check Link

Tip Remove the check link from the door through the center opening.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166766

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166766&pubCellSyskey=150019&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166766

|

Rear Side Door Check Link Replacement

Callout Component Name

Preliminary Procedures

1. Remove the Rear door trim panel. Refer to Rear Side Door Trim Panel Replacement.

2. Remove the water deflector. Rear Side Door Check Link Body Bolt

1

2

3

Caution: Refer to Fastener Caution in the Preface section.

Tighten

20 N·m (15 lb ft) Rear Side Door Check Link Bolt (Qty: 2)

Tighten 7 N·m (62 lb in)

Rear Side Door Check Link

Tip Remove the check link from the door through the center opening.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166771

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166771&pubCellSyskey=149892&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166771

|

Fuel Tank Filler Door Replacement

Callout Component Name

Fuel Tank Filler Door Bolt (Qty: 2)

1

2 Fuel Tank Filler Door

Caution: Refer to Fastener Caution in the Preface section.

Tighten

2.5 N·m (22 lb in)

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166773

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166773&pubCellSyskey=170572&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166773

|

Fuel Tank Filler Door Latch Replacement

Callout Component Name

Fuel Tank Filler Door Latch Bolt (Qty: 2)

Caution: Refer to Fastener Caution in the Preface section.

1

2 Fuel Tank Filler Door Latch

Procedure

Disconnect the electrical connector.

Tighten

2.5 N·m (22 lb in)

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166775

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166775&pubCellSyskey=150049&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166775

|

Fuel Tank Filler Pipe Housing Replacement

Callout Component Name

Fuel Filler Door Pocket Bolt (Qty: 3)

Caution: Refer to Fastener Caution in the Preface section.

1

2 Fuel Filler Door Pocket

Tip Remove fuel filler cap.

Tighten 10 N·m (89 lb in)

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166776

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166776&pubCellSyskey=72077&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166776

|

Hood Strut Replacement

Callout Component Name

Warning: When a hood hold open device is being removed or installed, provide alternate

support to avoid the possibility of damage to the vehicle or personal injury.

Hood Strut Retainer (Qty: 2)

Procedure

1

1. Release the locking tabs on the strut.

2. Ensure the clip is fully seared when rod is reinstalled. If the clip cannot be fully seated a new rod should be installed.

2 Hood Strut

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1869772

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1869772&pubCellSyskey=162516&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 1869772

|

Hood Front Weatherstrip Replacement

Callout

1

Component Name

Hood Front Weatherstrip

Procedure

The hood front weatherstrip is held in place with plastic retainers that are part of the weatherstrip.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1869830

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1869830&pubCellSyskey=162517&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 1869830

|

Hood Rear Weatherstrip Replacement

Callout

1

Component Name

Hood Rear Weatherstrip

Tip The hood front weatherstrip is held in place with plastic retainers that are part of the weatherstrip.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1845405

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1845405&pubCellSyskey=9355&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 1845405

|

Hood Rear Outer Seal Replacement

Callout

1

Component Name

Hood Rear Outer Seal

Procedure

1. Clean the area where the seal will be mounted. Use a suitable solvent with a mixture of 50 percent isopropyl alcohol and 50 percent water by volume, or high-flash naphtha.

2. Warm the hood panel using J hood rear outer seal installation.

3. Do NOT touch the adhesive surface when tape is removed. Peel the tape liner off and install the outer rear hood seal.

25070 Heat Gun, to a minimum, prior to the

Special Tools

J 25070 Heat Gun

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1869771

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1869771&pubCellSyskey=139198&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 1869771

|

Front Compartment Sight Shields Replacement

Callout Component Name

1 Front Compartment Front Sight Shield Plastic Retainer (Qty: 11) 2 Front Compartment Front Sight Shield

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 1867529

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1867529&pubCellSyskey=150070&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 1867529

|

Front Side Door Auxiliary Sealing Strip Replacement

Removal Procedure

1. Open the door.

2. Remove the door lower weather-strip from the door.

Installation Procedure

Page

2

of 2Document ID: 1867529

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1867529&pubCellSyskey=150070&pub

...

1. Install the door lower weather-strip.

2. Close door.

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 1867533

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1867533&pubCellSyskey=150073&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

| Document ID: 1867533

|

Body Repair

|

Rear Side Door Lower Rear Auxiliary Sealing Strip Replacement

Removal Procedure

1. Open the door.

2. Remove the door lower weather-strip from the door.

Installation Procedure

Page

2

of 2Document ID: 1867533

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1867533&pubCellSyskey=150073&pub

...

1. Install the door lower weather-strip.

2. Close door.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2166780

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166780&pubCellSyskey=150079&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166780

|

Liftgate Strut Replacement

Callout

1

Component Name

Liftgate Strut

Warning: When a lift gate hold open device is being removed or installed, provide alternate support to avoid the possibility of damage to the vehicle or personal injury.

Caution: Apply pressure only at the end of the liftgate/hood assist rod that you are removing or attaching. Do NOT apply pressure to the middle of the rod because damage or bending will result.

Procedure

• Release the locking tabs on the strut.

• Ensure the clip is fully seated when rod is reinstalled. If the clip cannot be fully seated, a new rod should be installed.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2151299

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2151299&pubCellSyskey=9340&pubO

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2151299

|

Hood Latch Support Replacement

Callout Component Name

Preliminary Procedure

Remove hood latch. Refer to Hood Primary and Secondary Latch Replacement.

Hood Latch Support Bolt (Qty: 3)

1

2 Hood Latch Support

Caution: Refer to Fastener Caution in the Preface section.

Tighten

10 N·m (89 lb in)

2009 Saturn VUE - AWD

Page

1

of 2Document ID: 2166784

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166784&pubCellSyskey=150098&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 2166784

|

Front Side Door Weatherstrip Replacement

Removal Procedure

1. Remove the door check link-to-body bolt.

2. Remove the door weatherstrip.

Installation Procedure

Page

2

of 2Document ID: 2166784

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166784&pubCellSyskey=150098&pub

...

1. Install the door weatherstrip.

Caution: Refer to Fastener Caution in the Preface section.

2. Install the door check link-to-body bolt.

Tighten Tighten the door check link-to-body bolt 20 N·m (15 lb ft).

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1867301

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1867301&pubCellSyskey=150100&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 1867301

|

Front Door Opening Weatherstrip Replacement

Callout

Component Name

Preliminary Procedures

1. Remove the center pillar lower garnish molding. Refer to Center Pillar Lower Garnish

Molding Replacement

2. Remove the windshield pillar garnish molding. Refer to Windshield Pillar Garnish

Molding Replacement

3. Remove the front door sill plate. Refer to Front Carpet Retainer Replacement .

Front Side Door Opening Weatherstrip

Procedure

1

1. Install the weatherstrip to the pinch-weld flange. Ensure that the weatherstrip is fully seated.

2. Mark the location of the weatherstrip opening when removing from the pinch weld.

3. Align the weatherstrip to the door opening with the bond joint positioned at the lower center of the door opening.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1843491

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1843491&pubCellSyskey=150104&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 1843491

|

Liftgate Weatherstrip Replacement

Callout

1

Component Name

Liftgate Weatherstrip

Procedure

Clean the area where the seal will be mounted. Use a suitable solvent with a mixture of 50 percent isopropyl alcohol and 50 percent water by volume, or highflash naphtha.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1867303

11/15/2010

http://localhost:9001/si/showDoc.do?docSyskey=1867303&pubCellSyskey=150112&pub

...

Bolted Exterior Body Panels and Closures

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Body Repair

| Document ID: 1867303

|

Rear Door Opening Weatherstrip Replacement

Callout

Component Name

Preliminary Procedure

1. Remove the center pillar lower garnish molding. Refer to Center Pillar Lower Garnish

Molding Replacement

2. Remove the rear door sill plate. Refer to Rear Carpet Retainer Replacement .

Rear Side Door Opening Weatherstrip

Procedure

1

1. Install the weatherstrip to the pinch-weld flange. Ensure that the weatherstrip is fully seated.

2. Mark the location of the weatherstrip opening when removing from the pinch weld.

3. Align the weatherstrip to the door opening with the bond joint positioned at the lower center of the door opening.

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 1751766

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=1751766&pubCellSyskey=9944&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Specifications

| Document ID: 1751766

|

Body Repair

|

Bumpers and Fascias

Fastener Tightening Specifications

Application

Front Bumper Air Deflector Screw/Bolt 2 N·m 18 lb in Front Bumper Fascia Bolts 10 N·m 89 lb in Front Bumper Fascia Shield Screw 2 N·m 18 lb in Front Bumper Impact Bar Bolts 30 N·m 22 lb ft Rear Bumper Fascia (Inside Wheel Well) Bolts 10 N·m 89 lb in Rear Bumper Fascia Center Bracket Bolts 10 N·m 89 lb in Rear Bumper Fascia Retainers 2 N·m 18 lb in Rear Bumper Fascia Side Bracket Bolts 7 N·m 62 lb in Rear Bumper Fascia Screws 2 N·m 18 lb in Rear Bumper Fascia Tail Lamp Pocket Screws 2 N·m 18 lb in Rear Bumper Fascia Upper Bracket Bolts 10 N·m 89 lb in Rear Bumper Impact Bar Bolts 30 N·m 22 lb ft

Specification

Metric English

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 1871873

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=1871873&pubCellSyskey=164223&pub

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 1871873

|

Body Repair

|

Front Bumper Fascia Energy Upper Absorber

Bumpers and Fascias

Replacement

Callout Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .

1 Front Bumper Fascia Energy Absorber Push Pin (Qty: 2)

Front Bumper Fascia Energy Absorber

2

Tip Release the 2 retaining tabs to remove the absorber assembly.

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 1871874

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=1871874&pubCellSyskey=164224&pub

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 1871874

|

Body Repair

|

Front Bumper Fascia Energy Lower Absorber

Bumpers and Fascias

Replacement

Callout Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement.

Front Bumper Fascia Energy Absorber

1

Tip Release the 2 retaining tabs to remove the absorber assembly.

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 2166924

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166924&pubCellSyskey=9987&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2166924

|

Body Repair

|

Bumpers and Fascias

Front Bumper Impact Bar Replacement

Callout Component Name

Preliminary Procedure

Remove the bumper fascia. Refer to Front Bumper Fascia Replacement.

Front Bumper Impact Bar Bolt (Qty: 8)

1

2

Caution: Refer to Fastener Caution in the Preface section.

Tighten

30 N·m (22 lb ft) Front Bumper Impact Bar

Procedure

1. Disconnect the electrical connectors/harnesses as needed.

2. Transfer any parts as needed.

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 1875880

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=1875880&pubCellSyskey=164867&pub

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 1875880

|

Body Repair

|

Bumpers and Fascias

Radiator Opening Upper Cover Replacement

Callout Component Name

1 Radiator Opening Upper Cover Plastic Retainer (Qty: 11) 2 Radiator Opening Upper Cover

2009 Saturn VUE - AWD

|

Page

1

of 2Document ID: 2166925

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166925&pubCellSyskey=9978&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2166925

|

Body Repair

|

Bumpers and Fascias

Front Bumper Fascia Replacement (Base)

Callout Component Name

Preliminary Procedures

1. Remove the radiator opening upper cover. Refer to Radiator Opening Upper Cover

Replacement.

2. Remove the front wheelhouse liner to fascia screw only. Refer to Front Wheelhouse

Liner Replacement.

3. Remove the front bumper fascia air deflector. Refer to Front Bumper Fascia Air

Deflector Replacement.

Front Bumper Fascia Bolt (Qty: 2)

Caution: Refer to Fastener Caution

1

2 Front Bumper Fascia Retainer (Qty: 2)

Tip Reach underneath the wheelhouse to access the bolts.

Tighten 10 N·m (89 lb in)

Front Bumper Fascia

in the Preface section.

3

Page

2

of 2Document ID: 2166925

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166925&pubCellSyskey=9978&pubObj

...

Tip Pull forward to remove the front bumper fascia.

2009 Saturn VUE - AWD

|

Page

1

of 2Document ID: 2166926

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166926&pubCellSyskey=9978&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2166926

|

Body Repair

|

Bumpers and Fascias

Front Bumper Fascia Replacement (Red Line)

Callout Component Name

Preliminary Procedures

1. Remove the front compartment sight shields. Refer to Front Compartment Sight

Shields Replacement.

2. Remove the front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement.

3. Remove the front bumper air deflector. Refer to Front Bumper Fascia Air Deflector

Replacement.

Front Bumper Fascia Bolt (Qty: 2)

1

2 Front Bumper Fascia Retainer (Qty: 2)

3

Caution: Refer to Fastener Caution in the Preface section.

Tighten

2 N·m (18 lb in)

Front Bumper Fascia

Procedure

1. Disconnect the electrical connectors.

2. Transfer necessary parts.

Page

2

of 2Document ID: 2166926

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166926&pubCellSyskey=9978&pubObj

...

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 2166928

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166928&pubCellSyskey=9972&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2166928

|

Body Repair

|

Bumpers and Fascias

Front Bumper Fascia Air Deflector Replacement

Callout Component Name

Preliminary Procedure

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.

1 Front Bumper Air Deflector Plastic Retainer (Qty: 2)

Front Bumper Air Deflector Bolt/Screw (Qty: 6)

2

3

4 Front Bumper Air Deflector

Caution: Refer to Fastener Caution in the Preface section.

Tighten

2 N·m (18 lb in) Front Bumper Air Deflector Bolt/Screw (Qty: 3)

Tighten 2 N·m (18 lb in)

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 2166929

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166929&pubCellSyskey=157374&pub

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2166929

|

Body Repair

|

Bumpers and Fascias

Front Bumper Fascia Skid Plate

Callout Component Name

Preliminary Procedure

Remove the front bumper fascia energy lower absorber. Refer to Front Bumper Fascia

Energy Lower Absorber Replacement.

Front Bumper Fascia Skid Plate Screw (Qty: 2)

1

2

Caution: Refer to Fastener Caution in the Preface section.

Tighten

2 N·m (18 lb in) Front Bumper Fascia Skid Plate

Tip Release the retaining tabs to remove the skid plate assembly.

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 1873258

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=1873258&pubCellSyskey=164348&pub

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 1873258

|

Body Repair

|

Bumpers and Fascias

Rear Bumper Fascia Lower Skid Plate Replacement

Callout Component Name

Preliminary Procedure

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

1 Rear Bumper Fascia Skid Plate Push Pins (Qty: 4) 2 Rear Bumper Fascia Skid Plate

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 2166930

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166930&pubCellSyskey=9990&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2166930

|

Body Repair

|

Bumpers and Fascias

Rear Bumper Fascia Replacement

Callout Component Name

Preliminary Procedure

Remove the right and left rear wheelhouse if needed. Refer to Rear Wheelhouse Panel Liner

Replacement.

Rear Fascia Bolt/Screw (Qty: 2)

1

2 Rear Fascia Retainer (Qty: 8)

3

Caution: Refer to Fastener Caution in the Preface section.

Tighten

10 N·m (89 lb in)

Rear Bumper Fascia

Procedure

1. Disconnect the electrical connector.

2. Transfer components as necessary.

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 2166931

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166931&pubCellSyskey=70088&pubO

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2166931

|

Body Repair

|

Bumpers and Fascias

Rear Bumper Fascia Bracket Replacement

Callout Component Name

Preliminary Procedure

Remove the rear bumper fascia. Refer to Rear Bumper Fascia Replacement.

Rear Fascia Side Bracket Screw (Qty: 3)

1

2 Rear Fascia Side Bracket

Caution: Refer to Fastener Caution in the Preface section.

Tighten

7 N·m (62 lb in)

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 2151298

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2151298&pubCellSyskey=9951&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2151298

|

Body Repair

|

Bumpers and Fascias

Rear Bumper Impact Bar Replacement

Callout Component Name

Preliminary Procedure

Remove the bumper fascia. Refer to Rear Bumper Fascia Replacement.

Rear Bumper Impact Bar Bracket Bolt (Qty: 6)

1

2

Caution: Refer to Fastener Caution in the Preface section.

Tighten

30 N·m (22 lb ft) Rear Bumper Impact Bar

Procedure

1. Unclip the electrical harness from the impact bar.

2. Transfer the necessary components.

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 2166933

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2166933&pubCellSyskey=9992&pubObj

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 2166933

|

Body Repair

|

Bumpers and Fascias

Rear Bumper Fascia Reflector Replacement

Callout Component Name

Preliminary Procedure

Remove the rear bumper. Refer to Rear Bumper Fascia Replacement.

1 Rear Bumper Fascia Bolt (Qty: 2)

Rear Bumper Fascia Reflector

Caution: Refer to Fastener Caution in the Preface section.

2

Tip Push forward on the tab in order to remove the reflector from the fascia.

Tighten 10 N·m (89 lb in)

2009 Saturn VUE - AWD

|

Page

1

of 1Document ID: 1869786

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=1869786&pubCellSyskey=157966&pub

...

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

| Document ID: 1869786

|

Body Repair

|

Bumpers and Fascias

Rear Bumper Fascia Insert Replacement

Callout Component Name

Rear Bumper Fascia Insert

1

Procedure

Pull down to remove.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1750239

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=1750239&pubCellSyskey=46713&pubO

...

Cellular, Entertainment, and Navigation

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Specifications

|

| Document ID: 1750239

|

Driver Information and Entertainment

Fastener Tightening Specifications

Application

Antenna Bracket Fastener 10 N·m 89 lb in Antenna Mast 10 N·m 89 lb in Communication Interface Module Bolt 3 N·m 27 lb in Front Speaker Screw 2.5 N·m 22 lb in Radio Screw 2.5 N·m 22 lb in Rear Speaker Screw 2.5 N·m 22 lb in

Specification

Metric English

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2079539

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2079539&from=sm

Cellular, Entertainment, and Navigation

|

Radio

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Schematic and Routing Diagrams

|

Driver Information and Entertainment

| Document ID: 2079539

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2079542

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2079542&from=sm

Cellular, Entertainment, and Navigation

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Speakers (UW6)

Schematic and Routing Diagrams

|

Driver Information and Entertainment

| Document ID: 2079542

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2079547

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2079547&from=sm

Cellular, Entertainment, and Navigation

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Audio Amplifier

Schematic and Routing Diagrams

|

Driver Information and Entertainment

| Document ID: 2079547

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2079550

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2079550&from=sm

Cellular, Entertainment, and Navigation

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Speakers (U61) 1 of 2

Schematic and Routing Diagrams

|

Driver Information and Entertainment

| Document ID: 2079550

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2079556

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2079556&from=sm

Cellular, Entertainment, and Navigation

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Speakers (U61) 2 of 2

Schematic and Routing Diagrams

|

Driver Information and Entertainment

| Document ID: 2079556

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2079562

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2079562&from=sm

Cellular, Entertainment, and Navigation

|

Digital Radio

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Schematic and Routing Diagrams

|

Driver Information and Entertainment

| Document ID: 2079562

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2079566

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2079566&from=sm

Cellular, Entertainment, and Navigation

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Steering Wheel Controls

Schematic and Routing Diagrams

|

Driver Information and Entertainment

| Document ID: 2079566

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2081050

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2081050&pubCellSyskey=149077&pub

...

Cellular, Entertainment, and Navigation

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Schematic and Routing Diagrams

|

Driver Information and Entertainment

| Document ID: 2081050

OnStar Schematics

OnStar

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 2167907

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=2167907&pubCellSyskey=149693&pub

...

Cellular, Entertainment, and Navigation

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Driver Information and Entertainment

| Document ID: 2167907

OnStar Button Assembly Replacement

Callout

Component Name

Preliminary Procedure

Remove the roof console assembly. Refer to Roof Console Replacement.

Communication Center Call Switch Screw (Qty: 2)

Caution: Refer to Fastener Caution in the Preface section.

1

Tighten 2 N·m (18 lb in)

Communication Center Call Switch Assembly

Procedure

2

1. Disconnect the electrical connection.

2. Reconfigure the OnStar System. Refer to Control Module References.

2009 Saturn VUE - AWD

Page

1

of 1Document ID: 1874904

12/2/2010

http://localhost:9001/si/showDoc.do?docSyskey=1874904&pubCellSyskey=149734&pub

...

Cellular, Entertainment, and Navigation

|

VUE, VUE Hybrid (VIN Z), Captiva Sport Service Manual

Repair Instructions

|

Driver Information and Entertainment

| Document ID: 1874904

Mobile Telephone Microphone Replacement

Callout Component Name

Preliminary Procedure

Remove the roof console assembly. Refer to Roof Console Replacement.

Communication Interface Mobile Microphone Assembly

1

Procedure

Disconnect the electrical connection.