Checkline DT-315AEB User Manual

– 1 –

TABLE OF CONTENTS

01.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02

02.0 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02

03.0 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03

04.0 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04

4.1 True RPM

4.2 Internal Triggering Mode

4.3 Synchronous Output Signal

4.4 FPM Display Mode

4.5 Deg m/sec Display Mode

05.0 Changing Memory Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07

06.0 Battery Management (DT-315A Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08

6.1 Charging the Battery

6.2 Replacing the Battery

07.0 Flash Tube Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09

08.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

09.0 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

10.0 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

WARNING

1. Do not look at the emitted light for long periods of
time, it can be harmful to the eyes.

2. Do not disassemble or repair the unit while in

operation.

3. Do not operate or store the instrument in the

following places: explosive areas, areas near
water, oil, dust or chemicals, or areas where
the temperature is above 104°F (40 °C).

– 12 –

10.0 WARRANTY

ELECTROMATIC Equipment Co., Inc. (ELECTROMATIC) warrants to the
original purchaser that this product is of merchantable quality and confirms
in kind and quality with the descriptions and specifications thereof. Product
failure or malfunction arising out of any defect in workmanship or material in the
product existing at the time of delivery thereof which manifests itself within one
year from the sale of such product, shall be remedied by repair or replacement of
such product, at ELECTROMATIC’s option, except where unauthorized repair,
disassembly, tampering, abuse or misapplication has taken place, as determined
by ELECTROMATIC. All returns for warranty or non-warranty repairs and/or
replacement must be authorized by ELECTROMATIC, in advance, with all
repacking and shipping expenses to the address below to be borne by the
purchaser.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE
WARRANTY OF MERCHANTABILITY AND FITNESS FOR ANY
PARTICULAR PURPOSE OR APPLICATION. ELECTROMATIC SHALL NOT
BE RESPONSIBLE NOR LIABLE FOR ANY CONSEQUENTIAL DAMAGE,
OF ANY KIND OR NATURE, RESULTING FROM THE USE OF SUPPLIED
EQUIPMENT, WHETHER SUCH DAMAGE OCCURS OR IS DISCOVERED
BEFORE, UPON OR AFTER REPLACEMENT OR REPAIR, AND WHETHER
OR NOT SUCH DAMAGE IS CAUSED BY MANUFACTURER’S OR
SUPPLIER’S NEGLIGENCE WITHIN ONE YEAR FROM INVOICE DATE.

Some State jurisdictions or States do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation may not apply to
you. The duration of any implied warranty, including, without limitation, fitness
for any particular purpose and merchantability with respect to this product, is

limited to the duration of the foregoing warranty. Some states do not allow
limitations on how long an implied warranty lasts but, not withstanding, this
warranty, in the absence of such limitations, shall extend for one year from the
date of invoice.

ELECTROMATIC Equipment Co., Inc.
600 Oakland Ave. Cedarhurst, NY 11516—USA
Tel: [phone]/ Tel: [phone]/ Fax: [phone]

Every precaution has been taken in the preparation of this manual. Electromatic Equipment Co., Inc.,
assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting
from the use of information contained herein. Any brand or product names mentioned herein are used for
identification purposes only, and are trademarks or registered trademarks of their respective holders.

– 2 –

1.0 INTRODUCTION

Congratulations on your purchase of a Check•Line® DT-311A or DT-315A
stroboscope/digital tachometer.

Please read the entire instruction manual thoroughly before initial set-up and
operation; the information contained herein will aid you in operating your
stroboscope safely and with excellent results.

If upon delivery shipping damage is detected, do not operate the unit. Notify the
shipping carrier immediately for damage claim instructions. Refer to nameplate
and record serial number for future reference.

Items included with the DT-311A/DT-315A are:

• Handle

• Flash tube removing tool

• AC charger/adapter (Model 315A only)

Optional Accessories:

• Carrying Case

2.0 SETUP

The DT-311A and DT-315A may be operated handheld or else mounted on a
tripod for added convenience.

To mount the strobe on a tripod (or any other mounting surface), use screw
1/4 -20unc, length 8mm or shorter for the tripod screwhole on the bottom.

– 11–

9.0 TROUBLESHOOTING

FPM reading is displayed but unit is not flashing:

• Flash tube may need to be replaced.
(see "Flash Tube Replacement" section).

Stroboscope is in external trigger mode, no flash:

• Check flash tube. Replace if necessary.

• Check for damaged wiring and/or loose pin connections.

Stroboscope is in internal trigger mode, no flash:

• Check flash tube. Replace if necessary.

• Check for damaged wiring and/or loose pin connections..

DT-311A

DT-315A

– 3 –

3.0 OVERVIEW

01. LED display: Displays

function and value

02. EXT: External mode

indicator

03. INT: Internal mode indicator

04. B-CH: Battery charge

indicator (DT-315A only)

05. FPM: Flash per minute

indicator

06. deg: Phase shift degree

indicator

07. mSec: Millisecond delay

time indicator

08. Signal switch: Switches

the unit from the external
mode to the internal mode
(and vice-versa)

09. Display mode switch: When unit is set to the externalmode, the strobe

will switch to RPM (FPM)/deg/msec each time “MODE” is depressed

RPM (FPM) Displays flashes per minute. External input 0-35,000 RPM

(FPM)

deg Displays flash delay in degrees
msec Displays flash delay in msec

10. Setter: Changes the flashing rate

11. (x2) Switch: In the internal mode, pressing “x2”doubles the flashing rate

12. (+) Switch: In the internal mode, when object appears to be standing still,

pressing “+” will give the illusion that the object is moving towards the
rotating direction at a speed of 1 rotation in 6 seconds

13. (÷2) Switch: In the internal mode, pressing “÷2” divides the flashing rate

by two

14. (–) Switch: In the internal mode, when object appears to be standing still,

pressing

“

–“ will give the illusion that the object is moving in reverse at a

speed of 1 rotation in 6 seconds

15. Input and output connector:

PIN #1: +12V
PIN #2: Synch output signal
PIN #3: Input signal
PIN #4: 0V

16. Power cord (DT-311A) / AC adapter (DT-315A)

17. Power switch

– 10 –

8.0 SPECIFICATIONS

INTERNAL MODE

Flashing Range 40.0 - 35,000 FPM (flashes per minute)

Accuracy ±0.01% of reading

Resolution 0.1 FPM: 40.0 - 4,999.9 FPM

0.2 FPM: 5,000 - 7,999.8 FPM

0.5 FPM: 8,000 - 9,999.5 FPM
1 FPM: 10,000 - 35,000 FPM

Phase Shift Use +/- push buttons (360° in 6 seconds)

Display Update Time 0.2 sec approx.

Output Signal Synchronous, 400 μsec. Pulse output,

0 to +12 VDC amplitude(approx.), 4.7 Kø impedance

Rate Multiplier/Divider Multiply by 2, divide by 2

EXTERNAL MODE

Flashing Range 0.0 - 35,000 FPM

Accuracy ±0.01% ±1 digit

Phase Shift 0 - 359° with 1° resolution

Delay Time 0 - 2,000 msec from 40 - 10,000 FPM

External Trigger Input Signal LO level: 0 - 0.8 VDC, HI level:

2.5 - 12 VDC or open collector (NPN),
pulse width 50 μsec min.

Input Impedance 4.7 Kø at 12 V / 6.8 Kø at 0 V

GENERAL

Display 5 digits, 0.4" (10 mm) high, LED

Flash Tube Power/Life Xenon, 10 W max. (100 million flashes)

Flash Duration 10 - 40 μsec

Sensor Power Supply 12 VDC (40 mA)

Low Battery Indicator Display shows all L’s

Power Requirement

DT-311A 115 VAC or 220 VAC ±10% 60/50 Hz, 30 VA

(specify voltage)

DT-315A Internal Battery Pack

Operating Temp. Range 32° - 104°F ( 0 - 40°C )

Weight

DT-311A 2.6 lb (1.2 kg)

DT-315A 4.4 lb (2 kg)

Dimensions

DT-311A 7.28"L x 4.72"W x 4.72"H (185 x 120 x 120 mm)
DT-315A 9.84"L x 4.72"W x 4.72"H (250 x 120 x 120 mm)

Warranty 1 year

Standard Accessories Handle, flash tube removal tool Handle, flash tube

removal tool and AC charger/adapter

Optional Accessories Carrying case