Chauvet Pro Ovation F-55WW Quick Start Guide

Quick Reference Guide

English EN Español ES Français FR Nederlands NL

QUICK REFERENCE GUIDE

About This Guide

The Ovation F-55WW Quick Reference Guide (QRG) has basic product information such as conn ection, mounting, menu options, and DMX values. Download the User Manual from www.chauvetprofessional.com

Disclaimer

The information and specifications contained in this QRG are subject to change without notice.

Safety Notes

• DO NOT open this product. It contains no user-serviceable parts.

• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.

• DO NOT look at the light source when the product is on.

• CAUTION: This product’s housing may be hot when lights are operating.

• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.

• DO NOT operate this product outdoors or in any location where dust, excessive heat, water, or humidity may affect it. (IP20)

• DO NOT leave any flammable material within 50 cm of this product while operating or connected to power.

• CAUTION: When transferring product from extreme temperature environments, (e.g ., cold truck to warm humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow product to fully acclimate to the surrounding environment before connecting it to power.

• USE a safety cable when mounting this product overhead.

• DO NOT operate this product if the housing, lenses, or cables appear damaged.

• DO NOT connect this product to a dimmer or rheostat.

• ONLY connect this product to a grounded and protected circuit.

• ONLY use the hanging/mounting bracket to carry this product.

• In the event of a serious operating problem, stop using immediately.

• The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.

Contact

Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux, contact your distributor to request support or return a product. From inside the U.S., UK, Ireland, Mexico, or Benelux, use the information in Contact Us at the end of this QRG.

What is Included

• Ovation F-55WW

•Gel frame

• Warranty Card

• Quick Reference Guide

AC Power

This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.

AC Plug

Connection Wire (U.S.) Wire (Europe) Screw Color

AC Live Black Brown Yellow/Brass AC Neutral White Blue Silver AC Ground Green/Yellow Green/Yellow Green

Replacing The Fuse

1. Disconnect this product from power.

2. Using a flat-head screwdriver, unscrew the fuse holder cap from the housing.

3. Remove blown fuse and replace with a good fuse of the same type and rating.

4. Screw the fuse holder cap back in place and reconnect power.

for more details.

• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breake r or by unplugging it.

Ovation F-55WW QRG Rev. 1

QUICK REFERENCE GUIDE

Mounting Clamp

Overhead Mounting

Safety Cable

DMX Linking

The Ovation F-55WW will work with a DMX controller using a 5-pin DMX serial connection. A DMX Primer is available from www.chauvetprofessional.com.

DMX Connection

The Ovation F-55WW uses a 5-pin DMX for its DMX personalities: 1, 2, or 5. See the User Manual for info rmation about connecting and configuring the product for DMX operation.

Master/Slave Connection

The Ovation F-55WW uses the DMX data connec tio n fo r its Ma ster/ S lav e mo d e. Se e the U ser Manu a l for in fo r ma tio n about how to connect and configure the product for master/slave operation.

RDM (Remote Device Management)

Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally along existing DMX cabling. Check the DMX controller’s User Manual or with the manufacturer as not all DMX controllers have this capability. The Ovation F-55WW supports RDM protocol that allows feedback to make changes to menu map options. Download the User Manual from www.chauvetprofessional.com

Mounting

Before mounting this product, read the Safety Notes. Use at least one mounting point per product. Make sure the mounting clamps are capable of supporting the weight of the product. For our Chauvet line of mounting clamps, go to

http://trusst.com/productcategory/truss-clamps/

Product Mounting Diagram

for more details.

Control Panel Description

Button Function

<MENU> Exits from the current menu or function

<ENTER>

<UP>

<DOWN>

Ovation F-55WW QRG Rev. 1

Enables the currently displayed menu or sets the currently selected value into the selected function

Navigates upwards through the menu list or increases the numeric value when in a function

Navigates downwards through the menu list or decreases the numeric value wh en in a function

QUICK REFERENCE GUIDE

Menu Map

Main Level Programming Levels Description

DMX Address Address 001–508

1CH 1-channel: Dimmer

DMX Channel

2CH 2-channel: Dimmer, strobe 5CH

Static

Master/Slave

Dimmer

Strobe Controls strobe rate

000-255

Master Master mode

Slave Slave mode

Off Linear dimmer

Dimmer Mode

Dimmer 1 Fast dimmer curve Dimmer 2 Medium dimmer curve Dimmer 3 Slow dimmer curve

On Display back light always on

10s

Back Light

20s 30s

600Hz

1200Hz

LED Frequency

2000Hz 4000Hz 6000Hz

25KHz

Fixture Hours _ _ _ _ Shows total product hours

Information

Version V_._-V_ _ Shows installed software version

UID _ _ _ _ _ _ _ _ _ _ _ _ Shows product UID

Factory Setting

Yes

Selects starting address (*highest channel restricted to personality chosen)

5-channel: Dimmer, Strobe, Auto programs, Auto speed, Dimmer speed.

Controls intensity

Turns off di splay backlight after 10 sec of inactivity

Turns off di splay backlight after 20 sec of inactivity

Turns off di splay backlight after 30 sec of inactivity

Selects the PWM output frequency

Reset to factory defaults

DMX Values

5 Ch

Channel Function Value Percent/Setting

1 Dimmer 000 2Strobe

3 Auto Programs

4 Auto Speed 000

5 Dimmer Speed

255 0-100%

000

010 No function

011

255 Strobe, slow to fast 010 No function

000 011

070 Auto Program 1

071

130 Auto Program 2

131

190 Auto Program 3

191

255 Auto Program 4 255 0-100% 051 Preset dimmer speed from display menu

000 052

101 Dimmer speed mode off

102

152 Dimmer speed mode 1 (fastest)

153

203 Dimmer speed mode 2

204

255 Dimmer speed mode 3 (slowest)

Ovation F-55WW QRG Rev. 1

QUICK REFERENCE GUIDE

2 Ch

Channel Function Value Percent/Setting

1 Dimmer 000 2Strobe

255 0-100%

000

010 No function

011

255 Strobe, slow to fast

1 Ch

Channel Function Value Percent/Setting

1 Dimmer 000

255 0-100%

Ovation F-55WW QRG Rev. 1

GUÍA DE REFERENCIA RÁPIDA

Acerca de Esta Guía

La Guía de Referencia Rápida (GRR) del Ovation F-55WW contiene información básica sobre el producto, como montaje, opciones de menú y valores DMX. Descargue el Manual de Usuario de www.chauvetprofessional.com información más detallada.

Exención de Responsabilidad

La información y especificaciones contenidas en esta GRR están sujetas a cambio sin previo aviso.

Notas de Seguridad

• NNO abra este producto. No contiene piezas reparables por el usuario.

• NO mire a la fuente de luz cuando el producto esté encendido.

• Para evitar un desgaste innecesario y alargar su vida útil, desconecte complemente el producto de la alimentación, mediante el interruptor o desenchufándolo, durante los periodos en los que no se use .

• Cuidado: cuando transfiera el producto desde ambientes con tem peratura extrema (p. ej., del remolque frío de un camión a una sala de baile con calor y humedad), puede formarse condensa ción en la electrónica interna del producto. Para evitar que se produzca una avería, d eje que el p roducto se aclima te completamen te al ambien te antes de conectar la alimentación.

• ¡CUIDADO! La carcasa de este producto está caliente cuando las luces están en funcionamiento.

• Monte este producto en una ubicación con ventilación adecuada, al menos a 20'' (50 cm) de superficies adyacentes.

• NO deje ningún material inflamable a menos de 50 cm de este pro ducto mientras esté fun cionando o conectado a la alimentación.

• USE un cable de seguridad cuando monte este producto en lo alto.

• NO ponga en funcionamiento este producto en el exterior o en cualquier ubicación en la que el polvo, calor excesivo, agua o humedad puedan afectarlo.

• NO ponga en funcionamiento este producto si sospecha que la carcasa, lentes o cables están dañados.

• NO conecte este producto a un atenuador o reostato.

• Conecte este producto SOLO a un circuito con toma de tierra y protegido.

• Use SOLAMENTE los soportes de colgar/montar o las asas para mover este producto.

• En caso de un problema grave de funcionamiento, deje de usarlo inmediatamente.

• La máxima temperatura ambiente es de 113 °F (45 °C). No haga funcionar este producto a temperaturas más altas.

Contacto

Fuera de EE.UU, Reino Unido, Irlanda, México o Benelux, póngase en contacto con su distribuidor para solicitar asistencia o devolver el producto.Visite Contact Us

para información de contacto.

Qué va Incluido

• Ovation F-55WW

• Marco de Gel

• Tarjeta de Garantía

• Guía de Referencia Rápida

Corriente Alterna

Este producto tiene una fuente de alimentación con detección automática que.uede funcionar con un rango de tensión de entrada de100 a 240 VCA, 50/60 Hz.

Enchufe CA

Conexión Cable (EE.UU.) Cable (Europa) Color del tornillo

CA Cargado Negro Marrón Amarillo/Latón

CA Neutro Blanco Azul Plata

CA Tierra Verde/Amarillo Verde/Amarillo Verde

fpara

• Para evitar un desgaste innecesario y alargar su vida útil, desconecte complemente el producto de la alimentación, mediante el interruptor o desenchu fándolo, durante los periodos en los que no se use.

Sustitución del Fusible

1. Desconecte el producto de la toma de corriente.

2. Con un destornillador de estrella Nº2 desatornille la tapa del portafusibles.

3. Quite el fusible fundido del portafusibles y sustitúyalo con otro del mismo tipo y categoría.

4. Vuelva a atornillar la tapa del portafusibles en su sitio y conecte de nuevo la alimentación.

Ovation F-55WW QRG Rev. 1

+ 14 hidden pages