How it Works
CHAUVET DJ
Loading...
F
G
H
I
Loading...
Loading...
Gobo Shot 50W IRC
User Manual
18 pgs1.06 Mb0
Table of contents
Loading...

CHAUVET DJ Gobo Shot 50W IRC User Manual

Download
Page 1
User Manual
Page 2
TABLE OF CONTENTS
1. Before You Begin .......................................................................................................... 3
Claims ....................................................................................................................................................... 3
2. Introduction ................................................................................................................... 5
3. Setup .............................................................................................................................. 7
Fuse Replacement .................................................................................................................................... 7
Power Linking ............................................................................................................................................ 8
Orientation ................................................................................................................................................. 9
Rigging ...................................................................................................................................................... 9
4. Operation ......................................................................................................................10
Starting Address ...................................................................................................................................... 10
4-Channel ................................................................................................................................................ 11
Manual Mode ........................................................................................................................................... 12
Display ..................................................................................................................................................... 12
Reset Software ........................................................................................................................................ 12
Load Factory Defaults ............................................................................................................................. 12
IRC-6 (Infrared Remote Control) ............................................................................................................. 13
IRC-6 Operation ...................................................................................................................................... 13
Wired Remote .......................................................................................................................................... 14
5. Technical Information ..................................................................................................16
6. Technical Specifications ..............................................................................................17
Page 2 of 18 Gobo Shot™ 50W IRC User Manual Rev. 5
Page 3
What Is

Unpacking
Instructions

and check the container to make sure all the
included accessories) appear damaged from
missing components or parts, damage not related to shipping,
Text
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected

Symbols

Critical installation, configuration, or operation information. Not damage to the product, or cause harm to the operator.

Disclaimer

are subject to change ity for any errors or
and reserves the right to revise or recreate this manual at any time.

1. BEFORE YOU BEGIN

Included

Claims

Conventions
• Gobo Shot™ 50W IRC
• 10 Gobos
• Hanging bracket with mounting
hardware
Carefully unpack the product immediately parts are in the package and are in good condition.
If the box or the contents (the product and shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®. Failure to report damage to the carrier immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Convention Meaning
Symbol Meaning
• Power cord
• Wired remote with RJ45 cable
• Warranty card
• Quick Reference Guide
The information and specifications contained in this User Manual without notice. CHAUVET® assumes no responsibility or liabil omissions, Download the latest version from www.chauvetlighting.com.
© Copyright 2014 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author Date
A. Leon 8/13/14
following these instructions may make the product not work, cause
Important installation or configuration information. The product may not function correctly if this information is not used.
Useful information.
Gobo Shot™ 50W IRC User Manual Rev. 5 Page 3 of 18
Page 4
Product at a
x
P
x
P
x
P
P
x
P

Safety Notes

Do not touch the product’s housing when operating because it may be very hot.
This product is not intended for permanent installation.
Glance
Use on Dimmer Outdoor Use Sound-Active DMX Master/Slave
These notes i nclude important information about the mounting, usage, and maintenance of this product; read before using the product.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing
the fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening device using a
safety cable.
• Make sure there are no flammable materials close to the product when operating.
•
• Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the product to rain or moisture.
• Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
• The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the product at higher temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
•
Auto Programs Auto-ranging Power Supply Replaceable Fuse User-Serviceable
• Keep this User Manual for future use. If you sell the product to another user, be sure to give this document to the next owner.
Page 4 of 18 Gobo Shot™ 50W IRC User Manual Rev. 5
Page 5

2. INTRODUCTION

Overview

Gel Frame Holder
Back Panel View
Gobo Door
Thumbscrew
IRC Sensor
DMX In
DMX Out
Wired Remote In
Gobo Door
LED Display
Thumbscrew
Gel Frame
Holder
Focus
Power In
Fuse Holder
Power Out
Safety Loop
Gobo Shot™ 50W IRC User Manual Rev. 5 Page 5 of 18
Wired Remote Out
Control Buttons
Page 6

Dimensions

10.2 in
258 mm
12.6 in
320 mm
12 in
306 mm
Page 6 of 18 Gobo Shot™ 50W IRC User Manual Rev. 5
Page 7

AC Power

ranging power supply and it can work with an
circuit breaker, power outlet, and
’s back panel, or
’s specifications chart. The listed current rating indicates the
(circuit breaker or fuse). Make
an appropriate electrical ground to avoid the risk of
a rheostat (variable resistor) or dimmer circuit, even
Fuse

3. SETUP

The Gobo Shot™ 50W IRC has an auto­input voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements ( wiring), use the current value listed on the label affixed to the product refer to the product product’s average current draw under normal conditions.
Always connect the product to a protected circuit sure the product has electrocution or fire.
Never connect the product to if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Replacement
Disconnect the product from power before replacing the fuse.
1. Disconnect the product from power.
2. With a flat-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse.
4. Replace with a fuse of the same ty pe and r atin g.
5. Screw the fuse holder cap back in place and reconnect power.
Always replace a blown fuse with another of the same type and rating.
Gobo Shot™ 50W IRC User Manual Rev. 5 Page 7 of 18
Page 8

Power Linking

provides power linking via the Edison/IEC outlet located in the back of the
Power Linking
The power linking diagram shown above corresponds to the North American
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
1st Product
2nd Product
3rd Product
Additional Products
The product unit.
Diagram
You can power link up to 9 Gobo Shot™ 50W IRC units on 120 VAC or up to 17 Gobo Shot™ 50W IRC units on 230 VAC.
version of the product ONLY! If using the product requirements may differ in your country or region.
Page 8 of 18 Gobo Shot™ 50W IRC User Manual Rev. 5
Page 9

Mounting

, read and follow the safety recommendations indicated in
may be mounted in any position; however, make sure
Mount the
always consider the length of the
knobs allow for directional adjustment when aiming the
on the
Mounting Clamp
CHAUVET®)
Safety Cable
(such as
from
CHAUVET®)
Rubber Feet
Hanging/Mounting
Bracket
Bracket
Knobs (2x)
Before mounting the product the Safety Notes.

Orientation

The Gobo Shot™ 50W IRC adequate ventilation is provided around the product.

Rigging

• Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
• Make sure that the structure or surface onto which you are mounting the product can support the product’s weight (see the Technical Specifications
).
• When mounting the product overhead, always use a safety cable. product securely to a rigging point, such as an elevated platform or a truss.
• When rigging the product onto a truss, you should use a mounting clamp of appropriate weight capacity (you must supply your own mounting clamps). The bracket has 13-mm holes, which are appropriate for this purpose.
• When po wer linking m ultiple products, you must power linking cable and mount the products close enough for the cable to reach.
• The bracket adjustment product to the desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the knobs.
• The rubber feet also serve as floor supports. When mou nting the product floor, make sure that the product and cables are away from people and vehicles.
(such as CLP-15 or
CLP-15N from
Mounting Diagram
CH-05
Adjustment
Gobo Shot™ 50W IRC User Manual Rev. 5 Page 9 of 18
Page 10

Control Panel
Operation

To access the control panel functions, use the four buttons located underneath the
<UP>

Menu Map

Main Function
Programming Levels
Description
CU
Reset
rESt
in this mode, changes in programming levels and settings
Configuration
When selecting a starting DMX address, always consider the number of DMX channels
choose a starting address that is too high, you could
DMX mode,

4. OPERATION

display.
Button Function
<MENU>
<DOWN>
<ENTER>
Selects an operation mode or backs out of the current menu option Scrolls up the list of options or selects a higher value Scrolls down the list of options or selects a lower value Activates a menu option or a selected value
DMX Address d001—d512
StoP
Gobo
Manual Mode nAn
Display diS
Load LoAd
While in Manual mode (nAn), the Gobo Shot™ 50W IRC also responds to the IRC-6. When using the IRC-6 will show on the display.
Set the product in DMX mode to control with a DMX controller.
(DMX)
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket on the product.
GoSP 000—255
diNN L000—L255 SHut S000—S100
CCU
diS
rdiS

Starting Address

the selected DMX mode uses. If you restrict the access to some of the product’s channels.
The Gobo Shot™ 50W IRC uses up to 4 DMX channels in its 4-channel which defines the highest configurable address to 509.
If unfamiliar with D MX, download the DMX Primer from www.chauvetlighting.com. To select the starting address, do the following:
1. Press <MENU> repeatedly until d001—d512 shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
Selects the DMX starting address Gobo rotation, stop Gobo rotation Reverse gobo rotation Gobo rotation speed Dimmer (0—100%) Shutter (0—20 Hz) Normal display Reverse display Resets fixture Loads factory defaults
Page 10 of 18 Gobo Shot™ 50W IRC User Manual Rev. 5
Page 11

DMX Channel Modes, Assignments, and Values

1
Dimmer
000 ó 255
0—100%
000 ó 003
216 ó 255
Closed
Open
000 ó 063
192 ó 255
Stop
Reverse rotation
4
Gobo Rotation Speed
000 ó 255
Gobo speed (slow to fast)

4-Channel

Channel Function Value Setting
2 Shutter
3 Gobo Rotation
004 ó 007 008 ó 215
064 ó 127 128 ó 191
Open Strobe, with increasing speed (0—20 Hz)
Rotation Stop
Gobo Shot™ 50W IRC User Manual Rev. 5 Page 11 of 18
Page 12

Configuration
(Standalone)

to a DMX string
Load Factory
Set the product in the standalone Manual mode to control without a DMX controller.
• Connect the product to a suitable power outlet.
Never connect a product that is operating in a standalone mode connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller.

Manual Mode

To enable the Manual mode, do the following:
1. Press <MENU> repeatedly until nAn shows on the display.
2. Press <ENTER> and Gobo, GoSP, diNN, or SHut show on the display.
3. Use <UP> or <DOWN> to select the desired option as follows.
To select from the gobo rotation options:
1. Select Gobo and press <ENTER>.
2. Use <UP> or <DOWN> to select CU (gobo rotation), CCU (reverse gobo rotation), or StoP (stop).
3. Press <ENTER>.
To select the gobo rotation speed:
1. Select GoSP and press <ENTER>.
2. Use <UP> or <DOWN> to select 000—255.
3. Press <ENTER>.
For dimmer control:
1. Select diNN and press <ENTER>.
2. Use <UP> or <DOWN> to select L000—L255 (0—100%).
3. Press <ENTER>.
To set the shutter speed:
1. Select SHut and press <ENTER>.
2. Use <UP> or <DOWN> to select S000—S100 (0—20 Hz).
3. Press <ENTER>.
Page 12 of 18 Gobo Shot™ 50W IRC User Manual Rev. 5

Display

Reset Software

Defaults
You are able to flip the display for easy readability in any mounting situation. To select your display angle:
1. Press <MENU> repeatedly until diS (normal dis play ) or rdiS (inverted display) shows on the display.
2. Use <UP> or <DOWN> to select the des ired display.
3. Press <ENTER>.
To reset the software in the Gobo Shot™ 50W IRC, do the following:
1. Press <MENU> repeatedly until rESt shows on the display.
2. Press <ENTER>.
To load the factory default settings in the Gobo Shot™ 50W IRC, do the following:
1. Press <MENU> repeatedly until LoAd shows on the display.
2. Press <ENTER>.
Page 13

IRC-6 (Infrared
Remote Control)

can be used to control one Gobo

IRC-6 Operation

The IRC-6 (infrared remote control) from CHAUVET® Shot™ 50W IRC. Set the product in Manual mode (nAn) to use the IRC-6.
Note: Make sure to point the IRC-6 directly at the receiver.
The following IRC-6 buttons are used with the Gobo Shot™ 50W IRC:
• <BLACKOUT> - tur n s LE D o n/off
• <STROBE> - strobing (0–20 Hz)
• <SPEED> - gobo rotation
Note: After pr essing the <SPEED> button, CU shows on the display until
you increase or decrease the gobo rotation speed (see below).
• <%> - master dimmer
• <MANUAL> - stops rotation
• <FADE/SNAP> - selects clockwise/counter-clockwise
• <+> (plus) - increases effect
- to increase gobo rotation, press the <SPEED> button first (settings 0–255)
- to increase strobing, press the <STROBE> button first (settings S000–S100)
- to increase dimming, press the <%> button first (settings L000–L255)
• <-> (minus) - decreases effect
- to decrease gobo rotation, press the SPEED button first (settings 0–255)
- to decrease strobing, press the STROBE button first (settings S000–S100)
- to decrease dimming, press the % button first (s ettings L000–L255)
• <0>–<9> - preset rotation speeds 0— 9 (slow to fast)
The buttons on the IRC-6 not listed above are reserved for future us e with the Gobo Shot™ 50W IRC.
The Gobo Shot™ 50W IRC responds to the IRC-6 while in Manual mode (nAn). When using the IRC-6 in this mode, changes in programming levels and settings will show on the display
Gobo Shot™ 50W IRC User Manual Rev. 5 Page 13 of 18
Page 14
the back of the
The Wired Remot e I n/Out ports allow one G o bo Shot™ 50W IRC to rem ote ly

Wired Remote

To operate the Gobo Shot™ 50W IRC with the included wired remote, follow the instructions below:
Plug the wired remote into the Wired Remote In port on projector, and use the remote as follows:
• To control the gobo’s rotation speed, turn the ROTATION SPEED knob to the desired speed (slow to fast).
• To control the direction of the gobo’s rotation, flip the DIRECTION switch to either CCW (counter-clockwise) or CW (clockwise).
• To control the power to the Gobo Shot™ 50W IRC, flip the POWER switch to either ON or OFF.
control the acti ons of another Gobo S hot ™ 50W IRC without the need of an additional wired re mote. Using a sta nd ard RJ45 (networ k) ca ble, co nnect the projector wit h th e wi re d remote from its Wir ed R e mot e Out port to the Wired Remote In port of the other proj ect or . G ob o Shot™ 50W IRC projectors confi gured in this ma nner operat e in unis on.
When using just one wired remote to control more than one Gobo Shot™ 50W IRC, be sure to use the RJ45 cables to connect the projectors. Do not use DMX connections or the fixtures will not respond correctly.
Page 14 of 18 Gobo Shot™ 50W IRC User Manual Rev. 5
Page 15

Included Gobos

Changing
Gobo Replacement Diagram
Gobos
Gobo
To change the gobos in the Gobo Shot™ 50W IRC, do the following:
1. Turn off and disconnect the product from power.
2. Place the product on a flat, level surface.
3. Loosen the gobo door thumbscrew and pull open the hin ged gobo door.
4. Remove the expansion ring that holds the gobo in place and remove the gobo from the gobo holder.
5. Insert a new gobo and hold it in place with the expansion ring.
6. Close the gobo door.
7. Tighten the gobo door thumbscrew.
Gobo Holder
Expansion Ring
Gobo Shot™ 50W IRC User Manual Rev. 5 Page 15 of 18
Page 16
Product
up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear. To maintain optimum
surfaces carefully after

5. TECHNICAL INFORMATION

Dust build-
Maintenance
performance and minimize wear, clean the product at least twice a month. However, usage and environmenta l condit io ns contr ib ut e to increased cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external surface/vents.
4. Clean all external optics and glass/transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
6. Softly wipe any dirt or grime to the outside edges of the external optics or glass/transparent surface.
7. Gently polish the external optics and glass/transparent surfaces until they are free of haze and lint.
Always dry the external optics and glass/transparent cleaning them.
Do not spin the cooling fan using compressed air because you could damage it.
Page 16 of 18 Gobo Shot™ 50W IRC User Manual Rev. 5
Page 17
Dimensions and
Length
Width
Height
Weight
12 in (306 mm)
12.6 in (320 mm)
10.2 in (258 mm)
10.8 lb (5 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
102 W
109 W
Operating current
0.8 A
0.4 A
Power linking current (units)
8 A (9 units)
8 A (17 units)
Fuse
F 2 A, 250 V
F 2 A, 250 V
Power I/O
US/Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Power
Lifespan
LED
50 W
50,000 hours
Color
Quantity
Current
White 1 2 A
Photo Optic
Parameter
Illuminance @ 2 m
2937 lx
Beam angle
26°
Strobe rate
0—20 Hz
53 mm outside
1 mm max thickness (size D)
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Fan-cooled
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
4
Ordering
Product Name
Item Code
UPC Number
Gobo Shot™ 50W IRC
03050718
781462210663

6. TECHNICAL SPECIFICATIONS

Weight
Gobo size
40 mm image
Gobo Shot™ 50W IRC User Manual Rev. 5 Page 17 of 18
Page 18
, United Kingdom, or Ireland, contact your distributor of
s to

Returns

Support office and request a Return
. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
end the merchandise prepaid, in its original box, and with its original packing
the following information on a piece of paper
properly. Any shipping damage resulting from inadequate
o use its own discretion to repair or replace

Contact Us

WORLD HEADQUARTERS - CHAUVET®
General Information
Toll free: (800) 762-1084
Technical Support
Wor l d Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - CHAUVET® Europe Ltd.
General Information
Fax: +44 (0)1773 511110
Technical Support
MEXICO - CHAUVET® Mexico
General Information
Voice: +52 (728) 285-5000
Technical Support
request support or to return a product. Visit our website for contact details.
To return a product or reques t supp ort :
• In the U.S., contact CHAUVET® World Headquarters (see below).
• In the UK or Ireland, contact CHAUVET® Europe Ltd. (see b elow ) .
• In Mexico, contact CHAUVET® Mexico (see below).
• In any other country, DO NOT contact CHA UV E T®. Contact your distributor. See
www.chauvetlighting.com
for distributors outside the U.S., United Kingdom, or
Ireland.
If you live outside the U.S. record and follow their instructions on how to return CHAUVET® product them. Visit our website for contact details.
Call the corresponding CHAUVET® Technical Merchandise Authorization (RMA) number before shipping the product
return. You must s
and accessories. CHAUVET® will not issue call tags. Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on the box.
Before sending the product, clearly write and place it inside the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product packaging will be your responsibility. FedEx packing or double-boxing are recommended.
CHAUVET® reserves the right t returned product(s).
Address: 5200 NW 108th Avenue Sunrise, FL 33351 Voice: (954) 577-4455 Fax: (954) 929-5560
Address: Unit 1C Brookhill Road Industrial Estate Pinxton, Nottingham, UK NG16 6NT Voice: +44 (0)1773 511115
Voice: (954) 577-4455 (Press 4) Fax: (954) 756-8015 Email: tech@chauvetlighting.com
Email: uktech@chauvetlighting.com Wor l d Wide Web www.chauvetlighting.co.uk
Page 18 of 18 Gobo Shot™ 50W IRC User Manual Rev. 5
Address: Av. Santa Ana 30 Parque Industrial Lerma Lerma, Mexico C.P. 52000
Outside the U.S., United Kingdom, Ireland, or Mexico, contact your dealer. Follow their instructions to
Email: servicio@chauvet.com.mx
Wor l d Wide Web www.chauvet.com.mx
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use