Chauvet COLORtube 3.0 EQ User Manual

CT3EQ

CONTROLLER

Snapshot

COLORTUBE™

3.0 EQ

Use on Dimmer

Outdoor

Sound Activated

DMX

Master/Slave

Autoswitching

Power Supply

External Power

Supply

Replaceable Fuse

User Serviceable

Duty Cycle

(Optional)

User Manual

3000 N 29th Ct, Hollywood, FL 33020 U.S.A.

[phone] – [phone]

FAX [phone]

www.chauvetlighting.com

TABLE OF CONTENTS

1. BEFORE YOU BEGIN............................................................................................................................................................ 3

WHAT IS INCLUDED ...................................................................................................................................................................... 3

UNPACKING INSTRUCTIONS ........................................................................................................................................................... 3

MANUAL CONVENTIONS ................................................................................................................................................................ 3

ICONS........................................................................................................................................................................................ 3

SAFETY INSTRUCTIONS................................................................................................................................................................. 4

2. INTRODUCTION .................................................................................................................................................................... 5

FEATURES.................................................................................................................................................................................. 5

PRODUCT OVERVIEW (CT3EQ CONTROLLER) ................................................................................................................................. 6

PRODUCT OVERVIEW (COLORTUBE™ 3.0 EQ) .............................................................................................................................. 7

3. SETUP .................................................................................................................................................................................... 8

AC POWER ................................................................................................................................................................................ 8

FIXTURE LINKING (COLORTUBE™ 3.0 EQ) .................................................................................................................................... 8

MOUNTING ................................................................................................................................................................................. 9

Orientation.......................................................................................................................................................................... 9

Rigging ............................................................................................................................................................................... 9

FIXTURE LINKING....................................................................................................................................................................... 10

Data Cabling .................................................................................................................................................................... 10

DMX Data Cable .............................................................................................................................................................. 10

Cable Connectors ............................................................................................................................................................ 10

3-Pin to 5-Pin Conversion Chart ..................................................................................................................................... 11

Setting up a DMX Serial Data Link ................................................................................................................................. 11

4. OPERATING INSTRUCTIONS ............................................................................................................................................ 12

CONFIGURING THE STARTING ADDRESS ........................................................................................................................................ 12

CONTROL PANEL FUNCTIONS ...................................................................................................................................................... 12

MENU MAP ............................................................................................................................................................................... 13

Operation ................................................................................................................................................................................ 14

DMX ................................................................................................................................................................................. 14

DMX CHANNEL VALUES ............................................................................................................................................................. 14

Mode Channel DMX Details ............................................................................................................................................ 15

Sound Active Mode Channel 2 Values ........................................................................................................................... 15

STANDALONE AUTOMATIC AND SOUND-ACTIVE .............................................................................................................................. 16

DIP Switch Settings ......................................................................................................................................................... 16

SETTING THE STARTING ADDRESS ............................................................................................................................................... 19

GENERAL TROUBLESHOOTING ..................................................................................................................................................... 19

CONTACT US ............................................................................................................................................................................ 19

5. APPENDIX ............................................................................................................................................................................ 20

DMX PRIMER ........................................................................................................................................................................... 20

GENERAL MAINTENANCE ............................................................................................................................................................ 20

RETURNS PROCEDURE ............................................................................................................................................................... 21

CLAIMS .................................................................................................................................................................................... 21

TECHNICAL SPECIFICATIONS ....................................................................................................................................................... 22

COLORtube™ 3.0 EQ ..................................................................................................................................................... 22

CT3EQ Controller (Optional) ........................................................................................................................................... 22

COLORtube™ 3.0 EQ User Manual 2 4/5/2010 11:04 AM

1. BEFORE YOU BEGIN

CONVENTION

MEANING

[10]

A DIP switch to be configured

<Menu>

A key to be pressed on the fixture’s control panel

1~512

A range of values

50/60

A set of values of which only one can be chosen

Settings

A menu option not to be modified (for example, showing the operating mode/current status)

MENU > Settings

A sequence of menu options to be followed

ON

A value to be entered or selected

ICONS

MEANING

This paragraph contains critical installation, configuration or operation information. Failure
to comply with this information may render the fixture partially or completely inoperative,
cause damage to the fixture or cause harm to the user.

This paragraph contains important installation or configuration information. Failure to
comply with this information may prevent the fixture from functioning correctly.

This paragraph reminds you of useful, although not critical, information.

What is included

 1 x COLORtube™ 3.0 EQ
 1 x Power Cable
 2 x Mounting Bracket Kit
 1 x Warranty Card

Unpacking Instructions

Manual Conventions

 1 x User Manual

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.

CHAUVET manuals use the following conventions to differentiate certain types of information from
the regular text.

Icons

This manual uses the following icons to indicate information that requires special attention on the part
of the user.

COLORtube™ 3.0 EQ User Manual 3 4/5/2010 11:04 AM

Safety Instructions

Please read these instructions carefully. It includes important
information about the installation, usage and maintenance of this
product.

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

Always make sure that you are connecting to the proper voltage, and that the line voltage you are

connecting to is not higher than that stated on the decal or rear panel of the fixture.

This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to

rain or moisture.
Make sure there are no flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent

surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing fuse and be sure to replace with

same fuse source.
Secure fixture to fastening device using a safety chain.
Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher

than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair the

unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center.
Never connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Avoid direct eye exposure to the light source while it is on.

COLORtube™ 3.0 EQ User Manual 4 4/5/2010 11:04 AM

2. INTRODUCTION

Features

7 user-selectable static colors plus blackout via master/slave
36 user-selectable automated programs with variable speeds via master/slave or optional controller
15 user-selectable EQ modes via master/slave
36 user-selectable EQ modes via optional controller
Additional power output: max 32 units
100 ft max distance between each tube
Includes 2 rail-mounted, sliding brackets
Mount flush to ceiling/wall or to truss with clamps
Center point and balance point marks
For best results, use the optional CT3EQ Controller

Options

CT3EQ Controller
5 ft (1.5 m) signal extension cable (LED-SIG5A)
15 ft (4.6 m) signal extension cable (LED-SIG15A)

CT3EQ Controller (Optional)
Features

6-channel DMX-COLORtube™ 3.0 EQ controller
RGB color mixing with variable strobe rate via stand-alone or DMX
7 selectable preset colors (plus blackout) with variable strobe speeds
Built-in RGB color fading with variable speeds
Built-in automatic programs via DMX (most with variable speed and/or strobe rates)
Built-in sound activated programs via DMX (36 different color combinations)

Additional Features

Controls up to 225 tubes
Addresses each tube automatically

COLORtube™ 3.0 EQ User Manual 5 4/5/2010 11:04 AM

Product Overview (CT3EQ Controller)

Sound

Sensitivity

Signal Output
to Tubes

ENTER
button

UP

button

Power Switch

Microphone

DMX LED

indicator

MODE

button

DOWN
button

DMX Out

DMX In

DC Power

Input

COLORtube™ 3.0 EQ User Manual 6 4/5/2010 11:04 AM

Signal In

Power In

Signal Out

Power Out

Power Indicator

Sound

Sensitivity

Microphone

DIP Switches

Product Overview (COLORtube™ 3.0 EQ)

Front Side

Back Side

COLORtube™ 3.0 EQ User Manual 7 4/5/2010 11:04 AM

(Optional)

Signal In

Signal

Power

Power In

3. SETUP

AC Power

This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line voltage

to which you are connecting it is within the range of accepted voltages.

Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat

(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0

to 100% switch.

To determine the power requirements for a particular fixture, see the label affixed to the back plate of

the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating indicates its

average current draw under normal conditions.

Always connect the fixture to a circuit with a suitable electrical ground.

Fixture Linking (COLORtube™ 3.0 EQ)

The COLORtube™ 3.0 EQ has both signal and power linking. Please see the diagram below for a description

on how to link these fixtures.

COLORtube™ 3.0 EQ User Manual 8 4/5/2010 11:04 AM

Step # 2

Step # 3

Pressure
Plate

Bolt and Lock

Washer

Mounting

Bracket

Mounting

Orientation

The COLORtube™ 3.0 EQ may be mounted in any safe position.

Rigging

Mount the fixture securely. This may be done with a screw, nut and bolt, or a hanging clamp. The hole in each
bracket is 13 mm in size. When rigging consider routine maintenance and DIP switch access. Please see the
following steps for installation.

1. Attach the bracket (1 or 2) to the mounting point.

2. Slide the bottom ridge of the tubes into place, as shown in the first diagram below.

3. Attach the pressure plate by using the bolt and lock washer that are included. This is done with a
#5 Allen wrench.

COLORtube™ 3.0 EQ User Manual 9 4/5/2010 11:04 AM

Fixture Linking

COMMON

DMX -

INPUT

OUTPUT

1

3

2 1 3

2

1

3

2

Resistance 120
ohm ¼ W between
pin 2 (DMX -) and
pin 3 (DMX +) on
the output of the
last fixture

To avoid signal transmission
problems and interference, it is
always advisable to connect a DMX
signal terminator.

DMX connector configuration

You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller
or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a serial data link determines the number
of fixtures the data link can support.

Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA­485 standard, no more than 32 fixtures should be connected on one data link. Connecting
more than 32 fixtures on one serial data link without the use of a DMX optically-isolated
splitter may result in deterioration of the digital DMX signal.

Data Cabling

To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.

DMX Data Cable

Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable must
have the following characteristics:

Maximum recommended serial data link distance: 500 m (1640 ft)
Maximum recommended number of fixtures on a serial data link: 32

Type: shielded, 2-conductor twisted pair
Maximum capacitance between conductors: 30 pF/ft
Maximum capacitance between conductor and shield: 55 pF/ft
Maximum resistance: 20 ohms/1000 ft
Nominal impedance: 100 ~ 140 ohms

Cable Connectors

Cabling must have a male XLR connector on one end and a female XLR connector on the other end.

Do not allow contact between the common and the fixture’s chassis ground. Grounding the
common can cause a ground loop, and your fixture may perform erratically. Test cables with
an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted
to the shield or each other.

COLORtube™ 3.0 EQ User Manual 10 4/5/2010 11:04 AM

This drawing
provides a general
illustration of the
DMX input/output
panel of a lighting
fixture.

Universal DMX Controller

Continue the link

3-Pin to 5-Pin Conversion Chart

3-PIN TO 5-PIN CONVERSION CHART

Conductor

3-Pin Female (Output)

5-Pin Male (Input)

Ground/Shield

Pin 1

Pin 1

Data ( - ) signal

Pin 2

Pin 2

Data ( + ) signal

Pin 3

Pin 3

Not used

Pin 4

Not used

Pin 5

If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to 3-pin
adapter. CHAUVET Model No: DMX5M, or DMX5F. The chart below details a proper cable
conversion:

Setting up a DMX Serial Data Link

1. Connect the (male) 3-pin connector side of

the DMX cable to the output (female) 3-pin
connector of the controller.

2. Connect the end of the cable coming from

the controller which will have a (female)
3-pin connector to the input connector of
the next fixture consisting of a (male) 3-pin
connector.

3. Then, proceed to connect from the output

as stated above to the input of the following
fixture and so on.

CHAUVET Certified DMX Data Cables

Order Code Description
DMX1.5 DMX Cable 1.5 m/4.9 ft
DMX4.5 DMX Cable 4.5 m/14.8 ft
DMX10 DMX Cable 10 m/32.8 ft

COLORtube™ 3.0 EQ User Manual 11 4/5/2010 11:04 AM

4. OPERATING INSTRUCTIONS

Button

Function

<MODE>

Used to select the current
operating mode, as well
as back out of the current
menu option

<UP>

Used to select increasing
advancement in the value

<DOWN>

Used to select decreasing
advancement in the value

<ENTER>

Used to select a value and
store it to memory

Configuring the Starting Address

Each fixture requires a starting address from 1~512. A fixture requiring one or more channels for
control begins to read the data on the channel indicated by the starting address. For example, a
fixture that uses seven DMX channels and is addressed to start on DMX channel 100, will read data
from channels: 100, 101, 102, 103, 104, 105 and 106. Choose the starting addresses for each fixture
so that the channels used do not overlap. In addition, you should note the starting address selected
for future reference.

The COLORtube™ 3.0 EQ fixture uses six DMX channels. If this is your first time using DMX, we
recommend reading the “DMX Primer” section in the “Appendix”.

Control Panel Functions

Access control panel functions using the four buttons located directly underneath the LCD Display on
the included wired remote.

The Control Panel shows the current state of the unit. It is used to select the operating mode, as well
as the sub-features. For a detailed layout of the control panel functions, please see the “menu map”
section on the following page.

COLORtube™ 3.0 EQ User Manual 12 4/5/2010 11:04 AM

Menu Map

MAIN FUNCTION

SUB-FUNCTION

SELECTION

INSTRUCTION

STATIC COLORS

Black

Flash

000~100

(0~100%)

Select different preset colors, as well as the strobe
speed

Red

Green

Blue

Yellow

Cyan

Purple

White

AUTO PROGRAM

1~35

Run/Flash Speed

001~100

(0~100%)

Set the speed of the program from one step to
another

Set the speed of the strobe

EQ SOUND MODE

1~36

Set the EQ sound mode

Interval

001~100

Set the interval between color changing: slow~fast

DMX-512

-

001~512

Sets the DMX starting address

COLOR FADE

Speed

000~100

(0~100%)

Set the speed of the program from one step to
another

MANUAL RGB

Red

000~100

(0~100%)

Set a custom color by combining red, green, and
blue together

Green

Blue

FIND TUBES

-

-

Automatically detect the quantity of tubes
connected in the series

For best results, first power on all of the tubes at the same time (simultaneously), and then power on
the controller.

COLORtube™ 3.0 EQ User Manual 13 4/5/2010 11:04 AM

OPERATION

1

2 3 4

5

6

Dimmer

000~005

Red
000~255

Green
000~255

Blue
000~255

No Function

000~005 No Strobe
006~255 Strobe

Red

006~011

No Function

No Function

No Function

Green

012~017

Blue

018~023

Yellow

024~029

Cyan

030~035

Purple

036~041

White

042~047

Mode 1~4
See Chart Below

048~071

000~255
Run Speed

000~005 No Strobe
006~255 Strobe

Mode 5~21
See Chart Below

072~173

000~255
Run Speed

No Function

Mode 22~34
See Chart Below

174~249

000~255
Run Speed

000~005 No Strobe
006~255 Strobe

Sound
See Chart Below

250~255

Sound
Activity Color
Change

No Function

No Function

DMX

This is the operating mode which will allow for control with an external DMX controller. You must set the starting
address for this mode. If this is your first time using DMX, then it is recommended that you refer to the “DMX
Primer” section in the “Appendix” of this manual.

1. Press <MODE> until DMX-512 appears on the LCD screen.

2. Press <ENTER>.

3. Using <UP> and <DOWN>, select the desired DMX address.

DMX Channel Values

COLORtube™ 3.0 EQ User Manual 14 4/5/2010 11:04 AM

Mode Channel DMX Details

CHANNEL 1 MODE (VALUES 048~249)

1.

3 Color Change

048~053

18.

Back N, Flow G 1

150~155

2.

7 Color Change

054~059

19.

Back N, Flow RB

156~161

3.

Rainbow 1

060~065

20.

Back N, Flow RG

162~167

4.

Rainbow 2

066~071

21.

Back N, Flow W

168~173

5.

3 Color Flow

072~077

22.

3 Color Flow Fill 2

174~179

6.

7 Color Flow

078~083

23.

7 Color Flow Fill 2

180~185

7.

3 Color Flow Roll 1

084~089

24.

3 Color Flow Roll 2

186~191

8.

7 Color Flow Roll 1

090~095

25.

7 Color Flow Roll 2

192~197

9.

3 Color Flow Fill 1

096~101

26.

Back R, Flow G 2

198~203

10.

7 Color Flow Fill 1

102~107

27.

Back G, Flow W 2

204~209

11.

3 Color Change

108~113

28.

Back B, Flow R 2

210~215

12.

7 Color Change

114~119

29.

Back W, Flow R 2

216~221

13.

Back R, Flow G 1

120~125

30.

Back N, Flow R 2

222~227

14.

Back G, Flow W 1

126~131

31.

Back N, Flow G 2

228~233

15.

Back B, Flow R 1

132~137

32.

Back N, Flow RB 2

234~239

16.

Back W, Flow R 1

138~143

33.

Back N, Flow RG 2

240~245

17.

Back N, Flow R 1

144~149

34.

Back N, Flow W 2

246~249

CHANNEL 2 (WHEN CHANNEL 1 MODE VALUES ARE 250~255)

No Function

000~006

Back: W

Active: B

133~139

Back: R

Active: G

007~013

Back: W

Active: RG

140~146

Back: R

Active: B

014~020

Back: W

Active: GB

147~153

Back: R

Active: GB

021~027

Back: N

Active: R

154~160

Back: R

Active: RG

028~034

Back: N

Active: G

161~167

Back: R

Active: RB

035~041

Back: N

Active: B

168~174

Back: R

Active: W

042~048

Back: N

Active: RB

175~181

Back: G

Active: R

049~055

Back: N

Active: RG

182~188

Back: G

Active: B

056~062

Back: N

Active: GB

189~195

Back: G

Active: RG

063~069

Back: N

Active: W

196~202

Back: G

Active: RB

070~076

G & DOT

203~209

Back: G

Active: W

077~083

GB & DOT

210~216

Back: B

Active: R

084~090

B & DOT

217~223

Back: B

Active: G

091~097

SYNC COLORS

224~230

Back: B

Active: RG

098~104

SYNC & DOT

231~237

Back: B

Active: RB

105~111

SYNC CROSS

238~244

Back: B

Active: W

112~118

CYCLE COLORS

245~251

Back: W

Active: R

119~125

AUTO MOTION

252~255

Back: W

Active: G

126~132

Sound Active Mode Channel 2 Values

COLORtube™ 3.0 EQ User Manual 15 4/5/2010 11:04 AM

Standalone Automatic and Sound-Active

DIP Switch Settings

COLORtube™ 3.0 EQ User Manual 16 4/5/2010 11:04 AM

COLORtube™ 3.0 EQ User Manual 17 4/5/2010 11:04 AM

COLORtube™ 3.0 EQ User Manual 18 4/5/2010 11:04 AM

Setting the Starting Address

SYMPTOM

POSSIBLE CAUSE(S)

POSSIBLE ACTION(S)

Breaker/Fuse

keeps blowing

Excessive circuit load

Check total load placed on the electrical circuit.

Short circuit along the power

wires

Check for a short in the electrical wiring (internal and/or

external).

Device does not

power up

No power

Check for power on Mains.

Loose power cord

Check power cord

Fixture is not

responding to

DMX

Wrong DMX addressing

Check Control Panel and unit addressing

Damaged DMX cables

Check DMX cables

Wrong polarity settings on the

controller

Check polarity switch settings on the controller
Loose DMX cables

Check cable connections

Faulty DMX interface

Replace DMX input

Faulty Main PCB

Replace Main PCB

Loss of signal

Non DMX cables

Use only DMX compatible cables

Bouncing signals

Install terminator as suggested.

Long cable / Low level signal

Install amplifier right after fixture with strong signal.

Too many fixtures

Install an optically coupled DMX splitter after unit #32.

Interference from AC wires

Keep DMX cables separated from power cables or

black lights.

This DMX mode enables the use of a universal DMX controller device. Each fixture requires a start address
from 1~512. A fixture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a fixture that uses six DMX channels and was addressed to start
on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and 105. Choose start
addresses so that the channels used do not overlap, and note the start address selected for future reference.

If this is your first time addressing a fixture using the DMX control protocol, we suggest jumping to the
“Appendix” section and reading the heading “DMX Primer”. It contains very useful information that will help you
understand its use.

General Troubleshooting

If you still have a problem after trying the above solutions, please contact CHAUVET Technical
Support.

Contact Us

World Wide

COLORtube™ 3.0 EQ User Manual 19 4/5/2010 11:04 AM

General Information CHAUVET

Technical Support CHAUVET

World Wide Web www.chauvetlighting.com

3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084

3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)

5. APPENDIX

DMX Primer

There are 512 channels in a DMX connection. Channels may be assigned in any manner. A fixture
capable of receiving DMX will require one or a number of sequential channels. The user must assign
a starting address on the fixture that indicates the first channel reserved in the controller. There are
many different types of DMX controllable fixtures and they all may vary in the total number of
channels required. Choosing a start address should be planned in advance. Channels should never
overlap. If they do, this will result in erratic operation of the fixtures whose starting address is set
incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET
carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)

General Maintenance

To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.

Unplug fixture from power.
Use a vacuum or air compressor and a soft brush to remove dust collected on external

vents.

Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl

Alcohol and a soft lint free cotton cloth or lens tissue.
Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.
Gently polish optical surfaces until they are free of haze and lint.

The cleaning of external optical lenses and/or mirrors must be carried out periodically to optimize light
output. Cleaning frequency depends on the environment in which the fixture operates. Damp, smoky
or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. Clean
with soft cloth using normal glass cleaning fluid. Clean the external optics at least every 20 days.
Clean the fixture at least every 30/60 days.

Always dry the parts carefully after cleaning them.

Never spin a fan using compressed air.

COLORtube™ 3.0 EQ User Manual 20 4/5/2010 11:04 AM

Returns Procedure

Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued.
Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #).
Products returned without the RMA # will be refused. Call CHAUVET and request an RMA # prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to pack fixture properly; any shipping damage resulting from

inadequate packaging is the customer’s responsibility. As a suggestion, proper UPS packing or

double-boxing is always a safe method to use.

CHAUVET reserves the right to use its own discretion to repair or replace product(s).

If you are given an RMA #, please include the following information on a piece of paper inside
the box:

1) Your name

2) Your address

3) Your phone number

4) The RMA #

5) A brief description of the symptoms

Claims

Damage incurred in shipping is the responsibility of the shipper; therefore, the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.

COLORtube™ 3.0 EQ User Manual 21 4/5/2010 11:04 AM

Technical Specifications

COLORtube™ 3.0 EQ

WEIGHT & DIMENSIONS

Length .............................................................................................................................. 39.2 in (995 mm)

Width .................................................................................................................................. 4.5 in (114 mm)

Height ................................................................................................................................... 2.9 in (75 mm)

Weight ..................................................................................................................................... 4 lbs (1.8 kg)

POWER

Autoswitching Power Supply ............................................................................... 100~240 VAC, 50/60 Hz

Power Consumption @ 120 V ........................................................................................ 36 W (0.3 A) max

Power Consumption @ 230 V ........................................................................................ 24 W (0.1 A) max

THERMAL

Maximum ambient temperature .......................................................................................... 104° F (40° C)

ORDERING INFORMATION

COLORtube™ 3.0 EQ ................................................................................................ COLORTUBE3.0EQ

WARRANTY INFORMATION

Warranty.................................................................................................................. 1-year limited warranty

CT3EQ Controller (Optional)

WEIGHT & DIMENSIONS

Length ................................................................................................................................ 8.4 in (214 mm)

Width .................................................................................................................................. 4.6 in (116 mm)

Height ................................................................................................................................... 1.8 in (47 mm)

Weight .................................................................................................................................. 0.6 lbs (0.3 kg)

POWER

External Autoswitching Power Supply (100~240 VAC, 50/60 Hz) ................................. 12 VDC, 500 mA

Power Consumption @ 120 V ........................................................................................ 12 W (0.1 A) max

Power Consumption @ 230 V ...................................................................................... 24 W (<0.1 A) max

THERMAL

Maximum ambient temperature .......................................................................................... 104° F (40° C)

CONTROL & PROGRAMMING

Data input ................................................................................................... locking 3-pin XLR male socket

Data output ............................................................................................. locking 3-pin XLR female socket

Data pin configuration................................................................................. pin 1 shield, pin 2 (-), pin 3 (+)

Protocols ........................................................................................................................ USITT DMX512-A

DMX Channels ........................................................................................................................................... 6

ORDERING INFORMATION

CT3EQ Controller ...................................................................................................CT3EQCONTROLLER

WARRANTY INFORMATION

Warranty.................................................................................................................. 2-year limited warranty

COLORtube™ 3.0 EQ User Manual 22 4/5/2010 11:04 AM