Channel Plus DA-506BID User Manual
Warranty
600-189 rev C
600-189 rev C
Multiplex Technology, Inc. warrants this product to be free
from defects in materials and workmanship for a period of
one year from the date of purchase or MTI will repair, or at
its option, replace the defective product. To obtain
warranty service, call MTI for a return material
authorization (RMA) number and return the product
prepaid to Multiplex Technology, Inc., 3001 Enterprise
Street, Brea, CA 92821, Attention: Customer Service.
Please put the RMA number on the outside of the carton.
Any implied warranty arising from the sale of the product
including implied warranties of merchantability and fitness
for purpose are limited to the warranty stated above. MTI
shall not be responsible for losses or damages or
expenses, whether direct, consequential or incidental
arising from the use of or the inability to use this product.
Some states do not allow limitations on how long the
implied warranty lasts or the exclusion or limitation or
incidental or consequential damages, so the above
limitations and exclusions may not apply to you. This
warranty gives you specific legal rights, and you may have
other rights which may vary from state to state.
Your DA-506BID is supplied with
extra mounting ears. These allow
the DA-506BID to be mounted in
any OpenHouse structured wire
grid system.
TM
+15vdc
300mA
catv/ant
bi-directional 1x6 coax panel for cable or antenna systems
DA-506BID
short
long
T
M
TM
DA-506BID
Specifications: typical @ 25 C ± 5 C
OO
+15
vdc
3
0
0
m
A
ca
tv/a
n
t
b
i-d
ire
c
tio
na
l 1x6
c
o
a
x p
an
e
l fo
r cab
le
o
r ante
nn
a
syste
m
s
DA-506BID
sh
o
rt
lo
n
g
T
M
TM
The DA-506BID video amplifier hub distributes CATV
or antenna signals to 6 TVs. The has four short
run outputs (up to 75 feet) and two long run outputs (up to 150
feet) for maximum flexibility. The has a
broadband 54-806MHz amplifier and a 5-42MHz reverse
channel which is compatible with pay-per-view, interactive
cable and cable modems.
DA-506BID
DA-506BID
CATV/Ant input to TV output 4
TV output to CATV/Ant input -8dB -12dB
(5-42MHZ reverse channel)
Bandwidth
Max CATV/Antenna input (64 channels) 20dBmV
Power supply (370-086 included)
Long Short
Output run distance: 150 feet 75 feet
Gain:
dB 1dB
Forward 54-806MHz
Reverse 5-42MHz
15 VDC @ 300mA
+
15
v
d
c
3
0
0
m
A
c
a
tv
/a
n
t
b
i-
d
ire
c
tio
n
a
l 1x
6
c
o
a
x
p
a
n
e
l fo
r
c
a
b
le
o
r a
n
te
n
n
a
s
y
s
te
m
s
DA-506BID
s
h
o
rt
lo
n
g
T
M
TM
Herringbone patterns on several channels.
A wavy pattern on the TV picture is caused by one or more spurious
signals in the 6MHz reserved for that TV channel. These spurious
signals, or ‘spurs’ can come from several places. For example, a
modulator at channel 16 will interject a spur into channel 15.
But the prime cause of spurs is an over-driven distribution amplifier.
(This is also known as IM or InterModulation distortion.)
To determine if an amplifier is causing this distortion, an inexpensive
variable attenuator will allow you to perform this simple test:
Insert the variable attenuator before the amp. (If you have splitters
between the amp and TV, that’s OK.) By the attenuation,
you are the signal that reaches the amp. If you find that
the herringbone patterns disappear, then your problem is an overdriven amplifier.
Causes of an over-driven amp:
1) Too much gain in the system. Use the variable attenuator to find a
setting where the signals are not noisy, and the amp is not being
over-driven.
2) Strong local FM signal. If you have a nearby FM transmitting
tower, you may need to install an FM trap before the amplifier.
3) Strong local TV signal.
increasing
decreasing
If you have a nearby TV transmitting tower,
you may need a tuned filter to reduce this station’s signal. Often the
station management can supply filters for their neighbors.
Variable attenuators and FM traps are available at many hardware
stores and most electronic stores.
For more troubleshooting tips and installation advice,
visit us on the web at www.channelplus.com.
Troubleshooting Tips
Loading...