Page 1
STANDARD FEATURES
• Access doors on both sides of hood
•Cleanout doors on end and side of machine for
quick access and service
• All-purpose 58" wide peg belt
• Automatic tank fill
• Chemical dispensing equipment
connection provisions
• Chrome-plated piping
(above top of machine)
• Convenient water connection
CH041
Upright 60" Conveyor
Water Saver
Dishwashing Machine
W-6-WS
W-6-WS UPRIGHT CONVEYOR
SPECIFIER STATEMENT
Specified unit will be a Champion model W6 steam
heated water saver high temperature upright conveyor
dishwashing machine.
Features quick release stainless steel Wash and Econo
Rinse spray arms with removeable end caps, vent
openings with 7" stainless steel stacks and locking
dampers on both ends, solid state controls, external
scrap bucket on 4 foot prewash aid. Capability to handle
more than 28,000 dishes per hour in a single operation.
One year parts and labor warranty.
Project____________________________________
Item No.____________________________________
Quantity______________________________________
Champion Industries, Inc.
P. O. Box 4149, Winston-Salem, NC 27115
Tel: 336/661-1556 Fax: 336/661-1979
www.championindustries.com
OPTIONS & ACCESSORIES
Auto Fill
Auto Fill with drain interlock
Blower-Dryer
(Requires minimum 11' unload)
Cold Water Thermostat
Prewash
External Scrap Bucket
8' Wash and/or Rinse Tank
De-Ionized Final Rinse
(Customer supplied de-ionized water)
Insulated Hood/Lower Panels
Isolation Switches
(motors)
Steam Pressure Regulator (unmounted)
Water Pressure Regulator (mounted)
Standard with built-in booster
Silverware Nozzle
For combination belt with silver warebelt on side
• Common drain
• Common electric connection
• Common steam connection (separate connection
required for optional blower-dryer)
• Control 120-volt circuit
• Conveyor drive motor, heavy duty 1-Hp
• Door safety switches on all inspection doors
• Electric eye conveyor shut-off switch on unload end
(with start switch)
• Enclosure panels on all four sides
•Energy sentinel (idle pump shut-off)
•Heavy-gauge stainless steel construction
•Low-water tank heat protection
•Prewash, wash and rinse dual pump motors
3-Hp each
• Push-button start-stop station on load and
unload end
•Tank heat: choice of steam coil or steam injector
•Top mounted control console, easy-to-reach
•Rinse saver economical energy system
(2M) 8/03 Printed in U.S.A.
Page 2
Plan
View
2
HP
2
HP
17"
6"
16"
38
1
/
2
"
Upright 60" Conveyor
Water Saver
Dishwashing Machine
W-6-WS
W-6-WS UPRIGHT CONVEYOR
Due to an ongoing value analysis program at Champion, specifications contained in this catalog are subject to change without notice.
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
C
L
3 HP
3 HP
3 HP
1
/
4
HP
1
/
4
HP
3 HP
3 HP
3 HP
68"
60"
10"
4"
48" 11"
42"
10"
6"
2 HP
6'
24"
Door
Drying Tunnel
Champion
32"
27
3
/4"
7"
4"
Start/Stop
1 HP
Drive
7' Min.
6"
5
3
/4"
36"
Dimensions and connections vary depending on length of
unload section.
Plumbing Notes: Due to variations in house supplied
steam and water pressures, steam and water pressure regulating
valves (PRV’s) are needed, (water PRV is standard on
machines with built-in booster.) The PRV’s can either be
purchased from Champion or obtained locally.
Warning: Plumbing and electrical connections should be
made by qualified workmen who will observe all the applicable
plumbing, sanitary, safety, and the National Electrical Code.
Note: Water Hammer Arrestor (meeting ASSE-1010
standard or equivalent) to be supplied by others, in common
supply line at service connection.
Basic Machine with One (1) 4' Prewash Unit
Plan View
Front View
Drying
Tunnel
Front View
24"
Door
24"
Door
4' 4'
10'
4' 5'
Min.
2'
24"
Door
7"
Start/Stop
20"
Clearance
12"
Plumbing
Clearance
99"
Door
Removal
61"
Machine
Height
38"
10"
4"
93
1
/4"
Door
Removal
12"
Door
Eco
Rinse Rinse Wash Prewash
ChampionChampionChampion
Champion
1/4
HP
3
HP
3
HP
3
HP
5
3
/4"
5"
A - Load B - Prewash C - Wash/Rinse & EcoRinse
D - Unload
SPECIFICATIONS
Minimum machine without blower-dryer:
A5, C10, D7 = 22'
Minimum machine with blower-dryer:
A5, C10, D13 = 28'
W-6-WS is available with the C10 section only.
Load section minimum length is 5'.
Unload section minimum length is 7' without
blower-dryer, and 13' with blower-dryer.
A B4 Prewash Unit is recommended.
W-6-WS may have more than one B or C sections.
Dimensions shown in inches
Loading...