Champion PP-28 User Manual
STANDARD FEATURES
• NEW Factory authorized startup
• Balanced door system
• Detergent/chemical connection provisions
• Door safety switch on each door
• Enclosure panels (front and sides)
• External lift-out refuse basket
• Fully automatic wash and rinse cycle
• Hold-down grid
• 7.5-Hp drip-proof pump motor
• Interchangeable upper and lower wash and rinse arms
• Low water tank heat protection
• Recessed, front-mounted controls
• Six-inch diameter vent connection
• Electric wash tank heat
PP-28 POT, PAN, UTENSIL WASHER
Project
Item No.
Quantity
PP-28
Pot, Pan, Utensil
Door Type
Washing Machine
OPTIONS & ACCESSORIES
: Corner Operation
: Straight-through Operation
: Front-loading Operation
: Ten-inch Shelf on front-loading machine
: Steam Coil tank heat
: Steam Injector tank heat
Boosters, Stainless Steel (completely interplumbed,
controls are interwired)
: Steam: 40°F Rise (built-in) (externally mounted
with cover for corner model)
: Steam: 70°F Rise (externally mounted with cover)
: Electric: 40°F Rise (built-in) (externally mounted
with cover for corner model)
: Electric: 70°F Rise (externally mounted with cover)
: Exhaust Fan, 1/3 Hp
: Racks, Stainless Steel (5" x 28" x 28")
: NEW Champion ION scale prevention system
NOTE: ALL electric boosters require separate electrical connection.
Photo is for general visual
representation only. Please
refer to specifications for
the latest detailed product
information.
SPECIFIER STATEMENT
Specified unit will be Champion model PP-28 pot, pan, utensil
door type washing machine.
Features adjustable wash cycle depending on solid wares from
2 to 5 minutes, revolving upper and lower high pressure spray
arms, large wash chamber spacious enough to accommodate
140 quart mixing bowls, fully automatic operation, and made
entirely of heavy gauge stainless steel from the base to spray
arms. One year parts and labor warranty.
Champion Industries, Inc.
3765 Champion Blvd., Winston-Salem, NC 27105
Tel: 336/661-1556 Fax: 336/661-1979
www.championindustries.com
(PDF) 12/15 Printed in U.S.A.
CH048
Champion, an Ali Group Company
PP-28
10"
2A
2A
1A
3A 6A 5A
4
5A
6A
4
1A
3A
2A
1A
3A
3B
4
1A3A
Steam BoosterElectric or Steam Heat
Front Loading
Operation
Corner
Operation
Plan ViewPlan View Plan View
34"
15"
11-1/4"
3-1/4"
4-1/4"
7-3/4"
2-3/4"
24"
28-1/2"
4-1/2" 4-1/2"
1"
9-1/2"
8-3/4"
24-1/4"
12-1/2"
4-1/2"
1"
73"
1"
2"
28-7/8"
1-1/2" Roll
36"
34"
Table
Height
Connection
12"
Plumbing
Clearance
106"
Doors
Removal
95"
Doors
Up
28-7/8" Opening
28-1/2" Inside Track
28-3/8"
Inside Track
Booster
Consult Factory
for Clearance
Booster
Consult Factory
for Clearance
* With built-in booster, allow
approximately 24" clearance
for ease of use.
Wall
Wall
28-3/8"
Inside Track
28"
Clearance
Through
Machine
19"
17"
24-1/4"
12-1/2"
10-1/2"
35-3/4"
42"
37"
25-1/4"
34"
15"
11-1/4"
3-1/4"
4-3/4"
6" Min.
6" Min.
6" Min.
6" Min.
4-3/4"
24"
28-1/2"
9-1/2"
4-5/8"
3"
4"
5"
4"
35-3/4"
33" 33"
33-1/4"
Pot, Pan, Utensil
Door Type
Washing Machine
Volume crated: 111 cu. ft.
Shipping weight crated: 1100 lbs.
Shipping weight crated
with built-in booster: 1200 lbs.
Front Loading
Operation
2-1/2"
Details, Dimensions & Connections
Electric or Steam Heat
70° Rise
Steam & Electric
Left Side
Mounted
70° Rise
Steam & Electric
Front
Mounted
70° Rise
Steam & Electric
Left Side
Mounted
Dimensions shown in inches
Typical Table Construction
51"
Corner Operation
Warning: Plumbing and electrical connections should be made
by qualified workmen who will observe all the applicable plumbing,
sanitary, safety codes and the National Electrical Code.
Plumbing Notes: Because of the variation in house-supplied steam
and water pressures, steam and water pressure regulating valves (PRVs)
are needed (water PRV is standard on model with built-in booster). The
PRVs can either be purchased from Champion or obtained locally.
Note: Water Hammer Arrestor (meeting ASSE-1010 standard or
equivalent) to be supplied (by others) in common water supply line at
service connection.
Machine Load Amps
Voltage Electric Heat Steam Heat
208/60/3 50 22 53 25
240/60/3 45 21 48 24
Electric Heat &
Exhaust Fan
480/60/3 22 11 24 13
Due to an ongoing value analysis program at Champion, specifications contained in this catalog are subject to change without notice.
Champion Industries, Inc., 3765 Champion Blvd., Winston-Salem, NC 27105 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
Front View Side View
Utilities
1 Electrical
A See box (1) for machine connection.
B See box (2) for separate built-in 27 kW electric booster connection.
2 Hot Water
A 1" NPT 180°F connection. Flow pressure 20-22 psi/82.5 gph.
B 1" NPT 140°F connection. Flow pressure 20-22 psi/82.5 gph.
Unmounted water PRV provided.
3 Drain
A 1-1/2" NPT connection. Maximum flow 15 gpm.
B 3/4" NPT steam booster relief to open drain.
4 Vent
6" diameter. 200 CFM. (Contact the factory for optional
exhaust fan connections.)
Steam Heat &
Exhaust Fan
5 Steam
A 3/4" NPT connection. Flow pressure 15-30 psi. (Tank heat only).
B 1-1/4" NPT connection (Tank & Booster 40° rise).
2” NPT connection (Tank & Booster 70° rise). Consult factory for location
6 Condensate
A 1/2" NPT machine connection return to boiler
(steam coil heat only).
B 3/4" NPT machine connection return to boiler
(steam heat, steam booster).
Loading...