Champion D-H1M3 Service Manual

The Dishwashing Machine Specialists

Technical Manual

Door-Type Dishwasher

Model D-HBM3

High Temperature with Built-in Booster

D-H1M3 High Temperature

D-LFM3 Low Temperature

June, 1998

P.O. Box 4149 Winston-Salem, North Carolina 27115-4149 336/661-1556 Fax: 336/661-1660 Email: champion@championindustries.com

Manual P/N 112428 Rev. A

Champion

Machine Serial No.

Champion Industries, Inc.

2674 N. Service Road Jordan Station, Ontario, Canada L0R 1S0 905/562-4195 Fax: 905/562-4618

For machines beginning with serial no. 90343 and above

Complete the information below so it will be available for quick reference.

Model Number

____________________________

Serial Number

_________________________

Voltage and Phase

_______________________________________________________________

Champion Parts Distributor

___________________________________

Phone

______________

______________________________________________________________________________

Champion Service Agency

____________________________________

Phone

______________

______________________________________________________________________________

Champion Industries Service: 1 (800) 858-4477 Champion Service Fax: 1 (336) 661-1660 In Canada:

Champion Service: 1 (800) 263-5798 Canada Service Fax: 1 (905) 562-4618

We strongly recommend that you fax your orders.

NOTE: When calling to order parts, be sure to have the model number, serial number, voltage, and phase of your machine.

Machine Data Plate

with Model & Serial number located on left side of control cabinet.

Revision History

Revision Revised Serial Number Comments

Date Pages Effectivity

10/6/97 All 90343 Issue manual with replacement parts lists 4/23/98 43 91586 Redesigned overflow lift arm P/N 112469 order

P/N’s 112469-S and 322218 for machines built prior to S/N 91586

REVISIONS

CONTENTS

Page

WARRANTY................................................................................................................................. 5

INTRODUCTION......................................................................................................................... 6

GENERAL .................................................................................................................................... 7

Model Numbers ...................................................................................................................... 7

Standard Equipment................................................................................................................ 7

Options.................................................................................................................................... 7

Accessories ............................................................................................................................. 7

Electrical Power Requirements............................................................................................... 8

INSTALLATION........................................................................................................................... 9

Unpacking............................................................................................................................... 9

Changing from Straight-through to Corner Operation........................................................... 9

Electrical Connections............................................................................................................ 10

Plumbing Connections............................................................................................................11

Water Connections.................................................................................................................. 11

Drain Connections .................................................................................................................. 12

Chemical Connections............................................................................................................13

Model D-HB, D-H1 and D-LF......................................................................................... 13

Detergent................................................................................................................................. 13

Rinse Aid/Sanitizer................................................................................................................. 14

INITIAL START-UP ..................................................................................................................... 16

Model D-HB, D-H1 and D-LF

OPERATION................................................................................................................................. 17

Model D-HB, D-H1 and D-LF

MAINTENANCE.......................................................................................................................... 18

Maintenance Schedule............................................................................................................18

CLEANING...................................................................................................................... 18

Every 2 Hours or After Each Meal Period

Model D-HB, D-H1 and D-LF............................................................................ 18

Every 8 Hours or at the End of the Day

Model D-HB, D-H1 and D-LF............................................................................ 18

DELIMING ...................................................................................................................... 19

Deliming process

Model D-HB, D-H1 and D-LF............................................................................ 19

OPERATION CHECKS................................................................................................... 20

Daily...........................................................................................................................20

Weekly ....................................................................................................................... 20

CONTENTS

Page

TROUBLESHOOTING.................................................................................................................20

BASIC SERVICE.......................................................................................................................... 22

Electrical Service.................................................................................................................... 22

Fuses................................................................................................................................. 23

Motor Overloads............................................................................................................... 23

Timers............................................................................................................................... 24

Timed Fill/Low Water Tank Heat Protection................................................................... 25

Heater Element Wiring..................................................................................................... 26

Motor Connections........................................................................................................... 27

Mechanical Service................................................................................................................. 28

Pump Seal Replacement ................................................................................................... 28

REPLACEMENT PARTS LIST .................................................................................................... 29

ELECTRICAL SCHEMATICS .................................................................................................... 64

LIST OF FIGURES

Figure 1 — Placement for Corner Operation.............................................................................. 9

Figure 2 — Changing the Track Assembly ................................................................................ 10

a — Straight-Through Configuration

b — Corner Configuration

Figure 3 — D-HB 3/4" NPT Water Supply Connection............................................................. 11

Figure 4 — D-H1/ D-LF 3/4" NPT Water Supply Connection.................................................. 11

Figure 5 — Drain Connection..................................................................................................... 12

Figure 6 — Chemical Connection Points ................................................................................... 13

Figure 7 — Wash Tank Detergent Equipment Insertion Points................................................. 13

Figure 8 — Rinse Aid Injection Point (D-HB, D-H1 Only) ...................................................... 14

Figure 9 — Rinse Aid/Sanitizer Injection Points (D-LF)........................................................... 15

Figure10 — Operator Controls .................................................................................................... 16

Figure11 — Door Activated Drain Lever Assembly ................................................................... 16

Figure 12 — Fuses........................................................................................................................ 23

Figure 13 — Motor Overload....................................................................................................... 23

Figure 14 — Cycle Timer ............................................................................................................. 24

Figure 15 — Cycle Timer Chart ................................................................................................... 24

Figure 16 — Fill Timer................................................................................................................. 24

Figure 17 — Fill Timer Chart....................................................................................................... 24

Figure 18 — Float Switch ............................................................................................................. 25

Figure 19 — Float Switch Troubleshooting Chart........................................................................ 25

Figure 20 — Pump Motor Wiring Diagrams................................................................................ 27

Figure 21 — Pump Seal Replacement.......................................................................................... 28

Figure 22 — Doors, Panels and Gauges....................................................................................... 30

Figure 23 — Door Guides, Stops, and Lift Bracket..................................................................... 32

Figure 24 — Door Handle and Spring Assembly ........................................................................ 34

CONTENTS

LIST OF FIGURES (cont’d)

Figure 25— Track Assembly....................................................................................................... 36

Figure 26 — Wash/Rinse Spray Piping ........................................................................................ 38

Figure 27 — Wash/Rinse Spray Arms ......................................................................................... 40

Figure 28 — Drain Assembly and Scrap Screens ........................................................................ 42

Figure 29 — Wash Tank Heat, Thermostats, and Float Switch.................................................... 44

Figure 30 — Electric Booster and Thermostat (D-HB Only)....................................................... 46

Figure 31 — D-HB Lower Fill Piping Assembly......................................................................... 48

Figure 32 — D-HB, D-H1 Upper Fill Piping Assembly .............................................................. 50

Figure 33 — D-H1, D-LF Lower Fill Piping Assembly .............................................................. 52

Figure 34 — D-LF Upper Fill Piping Assembly.......................................................................... 54

Figure 35 — Pump Assembly ....................................................................................................... 56

Figure 36 — Control Cabinet........................................................................................................ 58

Figure 37 — Dishracks and PRV.................................................................................................. 60

Figure 38 — Electrical Schematic D-HB/D-H1/D-LF, 3 Phase................................................... 64

Figure 39 — Electrical Schematic D-HB/D-H1/D-LF, 1 Phase................................................... 65

CONTENTS

WARRANTY

LIMITED WARRANTY

Champion Industries Inc. (herein referred to as Champion), P.O. Box 4149, Winston-Salem, North Carolina 27115, and P.O. Box 301, 2674 North Service Road, Jordan Station, Ontario, Canada, L0R 1S0, warrants machines, and parts, as set out below.

Warranty of Machines: Champion warrants all new machines of its manufacture bearing the name “Champion”

and installed within the United States and Canada to be free from defects in material and workmanship for a period of one (1) year after the date of installation or fifteen (15) months after the date of shipment by Champion, whichever occurs first. [See below for special provisions relating to glasswashers.] The warranty registration card must be returned to Champion within ten (10) days after installation. If warranty card is not returned to Champion within such period, the warranty will expire after one year from the date of shipment.

Champion will not assume any responsibility for extra costs for installation in any area where there are jurisdictional problems with local trades or unions.

If a defect in workmanship or material is found to exist within the warranty period, Champion, at its election, will either repair or replace the defective machine or accept return of the machine for full credit; provided, however, as to glasswashers, Champion’s obligation with respect to labor associated with any repairs shall end (a) 120 days after shipment, or (b) 90 days after installation, whichever occurs first. In the event that Champion elects to repair, the labor and work to be performed in connection with the warranty shall be done during regular working hours by a Champion authorized service technician. Defective parts become the property of Champion. Use of replacement parts not authorized by Champion will relieve Champion of all further liability in connection with its warranty. In no event will Champion’s warranty obligation exceed Champion’s charge for the machine. The following are not covered by Champion’s warranty:

a. Lighting of gas pilots or burners. b. Cleaning of gas lines. c. Replacement of fuses or resetting of overload breakers. d. Adjustment of thermostats. e. Adjustment of clutches. f. Opening or closing of utility supply valves or switching of electrical supply current. g. Cleaning of valves, strainers, screens, nozzles, or spray pipes. h. Performance of regular maintenance and cleaning as outlined in operator’s guide. i. Damages resulting from water conditions, accidents, alterations, improper use, abuse,

tampering, improper installation, or failure to follow maintenance and operation procedures.

j. Wear on Pulper cutter blocks, pulse vanes, and auger brush. Examples of the defects not covered by warranty include, but are not limited to: (1) Damage to the exterior or

interior finish as a result of the above. (2) Use with utility service other than that designated on the rating plate. (3) Improper connection to utility service. (4) Inadequate or excessive water pressure. (5) Corrosion from chemicals dispensed in excess of recommended concentrations. (6) Failure of electrical components due to connection of chemical dispensing equipment installed by others. (7) Leaks or damage resulting from such leaks caused by the installer, including those at machine table connections or by connection of chemical dispensing equipment installed by others. (8) Failure to comply with local building codes. (9) Damage caused by labor dispute.

Warranty of Parts: Champion warrants all new machine parts produced or authorized by Champion to be free

from defects in material and workmanship for a period of 90 days from date of invoice. If any defect in material and workmanship is found to exist within the warranty period Champion will replace the defective part without charge.

DISCLAIMER OF WARRANTIES AND LIMITATIONS OF LIABILITY

. CHAMPION’S WARRANTY IS ONLY TO THE EXTENT REFLECTED ABOVE. CHAMPION MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED, TO ANY WARRANTY OF MERCHANTABILITY, OR FITNESS OF PURPOSE. CHAMPION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THE REMEDIES SET OUT ABOVE ARE THE EXCLUSIVE REMEDIES FOR ANY DEFECTS FOUND TO EXIST IN CHAMPION DISHWASHING MACHINES AND CHAMPION PARTS, AND ALL OTHER REMEDIES ARE EXCLUDED, INCLUDING ANY LIABILITY FOR INCIDENTALS OR CONSEQUENTIAL DAMAGES.

Champion does not authorize any other person, including persons who deal in Champion dishwashing machines to change this warranty or create any other obligation in connection with Champion Dishwashing Machines.

INTRODUCTION

Welcome to Champion . . .

and thank you for allowing us to take care of your dishwashing needs.

This manual covers the door-type series dishwasher models D-H1, D-HB, and D-LF. Your machine was completely assembled, inspected, and thoroughly tested at our factory before it was shipped to your installation site.

This manual contains:

• Warranty Information

• Operation and Cleaning Instructions

• Maintenance Instructions

• Troubleshooting Guide

• Basic Service Information

• Replacement Parts Lists

• Electrical Schematics

Complete and return your warranty registration card within ten (10) days after the installation of your machine.

All information, illustrations and specifications contained in this manual are based upon the latest product information available at the time of publication. Champion constantly improves its products and reserves the right to make changes at any time or to change specifications or design without notice and without incurring obligation.

For your protection, factory authorized parts should always be used for repairs. Replacement parts may be ordered from your Champion authorized parts distributor or

from your Champion authorized service agency. When ordering parts, please supply the model number, serial number, voltage and phase of your machine, the part number, part description and quantity.

INTRODUCTION

GENERAL

This manual covers the Champion door type dishwashing machine. These machines are fully automatic and come equipped with a 1-HP pump motor.

The D-series dishwasher is available in the following models:

Model Numbers

D-H1, D-HB, D-LF The D-H1 model is a high temperature (180°F/82°C rinse) sanitizing model without booster. The D-HB model is a high temperature (180°F/82°C rinse) sanitizing model with booster. The D-LF is a low temperature (Min. 120°F/49°C-140°F/60°C Optimum) sanitizing model for

use with a sodium hypochlorite (Chlorine) based sanitizer at a minimum concentration of 50PPM in the final rinse.

Standard Equipment includes:

D-H1, D-HB, D-LF

• Automatic tank fill • Common utility connections

• Built-in electric (D-HB only) or • Two dish racks (peg and flat bottom)

steam booster heater (D-HB only) • Detergent/chemical connection provisions

• Door activated drain • Stainless steel front and side panels

• Field convertible to corner model • Top-mounted, splash-proof control console

• Electric tank heat • 60-second time cycle

• Balanced three door lift system • 1-1/2" O.D. gravity drain connection

• Low-water tank heat protection • Water pressure regulating valve

• 1-hp drip-proof pump motor (mounted) (D-HB only)

• Door safety switches • Interchangeable upper and lower spray arms

Options (D-HB only)

• Electric booster (70°F/39°C temperature rise)

heater for 110°F/43°C supply water

• Steam injector or steam coil tank heat

(steam booster 40°F/23°C – 70°F/39°C rise)

• Single source gas booster system

Accessories

Additional dishracks: Dish rack (peg) P/N 101285 Silverware rack (flat bottom) P/N 101273 3/4” Pressure reducing valve (PRV) P/N 112387

GENERAL

Electrical Power Requirements for Electric Heat / Electric Booster

Model Voltage Booster Rise Machine Power Requirement

(D-HB Only) Full Load Amps (125% Service Factor)

D-H1/LF 115/60/1 — 48 Amps 60 Amps D-H1/LF 208/60/1 — 23 Amps 29 Amps D-H1/LF 220/60/1 — 23 Amps 29 Amps D-H1/LF 230/60/1 — 23 Amps 29 Amps D-H1/LF 240/60/1 — 24 Amps 30 Amps D-H1/LF 208/60/3 — 12 Amps 15 Amps D-H1/LF 220/60/3 — 13 Amps 16 Amps D-H1/LF 230/60/3 — 13 Amps 16 Amps D-H1/LF 240/60/3 — 13 Amps 16 Amps D-H1/LF 380/60/3 — 7 Amps 9 Amps D-H1/LF 415/60/3 — 8 Amps 10 Amps D-H1/LF 480/60/3 — 6 Amps 8 Amps D-H1/LF 575/60/3 — 5 Amps 6 Amps

D-HB 115/60/1 — — — D-HB 208/60/1 40°F/23°C 59 Amps 74 Amps D-HB 220/60/1 40°F/23°C 61 Amps 76 Amps D-HB 230/60/1 40°F/23°C 63 Amps 79 Amps D-HB 240/60/1 40°F/23°C 65 Amps 81 Amps D-HB 208/60/3 40°F/23°C 33 Amps 41 Amps D-HB 220/60/3 40°F/23°C 35 Amps 44 Amps D-HB 230/60/3 40°F/23°C 36 Amps 45 Amps D-HB 240/60/3 40°F/23°C 37 Amps 46 Amps D-HB 380/60/3 40°F/23°C 20 Amps 25 Amps D-HB 415/60/3 40°F/23°C 20 Amps 25 Amps D-HB 480/60/3 40°F/23°C 17 Amps 21 Amps D-HB 575/60/3 40°F/23°C 14 Amps 18 Amps

D-HB 115/60/1 — — — D-HB 208/60/1 — — — D-HB 220/60/1 — — — D-HB 230/60/1 — — — D-HB 240/60/1 — — — D-HB 208/60/3 70°F/39°C 50 Amps 63 Amps D-HB 220/60/3 70°F/39°C 52 Amps 65 Amps D-HB 230/60/3 70°F/39°C 54 Amps 68 Amps D-HB 240/60/3 70°F/39°C 56 Amps 70 Amps D-HB 380/60/3 70°F/39°C 30 Amps 38 Amps D-HB 415/60/3 70°F/39°C 33 Amps 41 Amps D-HB 480/60/3 70°F/39°C 28 Amps 35 Amps D-HB 575/60/3 70°F/39°C 23 Amps 29 Amps

GENERAL

INSTALLATION

Unpacking

CAUTION:

Care should be taken when lifting the machine to prevent damage.

1. Immediately after unpacking the machine, inspect for any shipping damage.

If damage is found, save the packing material and contact the carrier immediately.

2. Remove the dishwasher from the skid. Adjust the feet if required, then move the

machine to its permanent location.

3. Level the machine (if required) by placing a level on the top of machine and adjusting

the feet. Level the machine front-to-back and side-to-side.

4. Remove the two dishracks and pressure gauge from the interior of the machine.

Install the pressure gauge in the upper fill piping of the dishwasher in the petcock provided.

NOTE:

The installation of your machine must meet local health codes.

Changing from Straight-through to Corner Operation

Your door-type dishwasher is shipped from the factory in a straight-through configuration. The following instructions explain how to convert your machine for corner operation.

Refer to Fig. 1 below.

1. Place the dishwasher so the operator controls are readily accessible.

2. Minimum clearance from any corner wall is 5-1/4" (133mm).

INSTALLATION

Figure 1

Placement for Corner Operation

Note:

Power switch is readily accessible.

Do not place the dishwasher closer than 5-1/4" (133mm) to any wall.

5-1/4"[133mm] MIN.

WALL

FRONT

POWER ON SWITCH

5-1/4"[133mm] MIN.

WALL

FRONT

POWER ON SWITCH

Changing from Straight-through to Corner Operation (cont’d)

Refer to Fig. 2 and perform the steps below.

1. Remove the front rack guide (A). Discard the square spacers.

2. Move front rack guide (A) to the left side of the rack tracks. (See Fig. 2b) Use existing hardware.

3. Unbolt the track (B) and rack support rod (C).

4. Remove and save the two remaining fasteners from rear track.

5. Bolt (B) and (C) as shown in Fig. 2b.

Electrical Connections

WARNING:

Electrical and grounding connections must comply with the National Electrical Code and/or Local Electrical Codes.

WARNING:

When working on the dishwasher, disconnect the electric service and place a tag at the disconnect switch to indicate work is being done on that circuit.

1. A qualified electrician must compare the electrical power supply with the machine electrical specifications stamped on the MACHINE ELECTRICAL CONNECTION PLATE located inside the top mounted control cabinet before connecting to the incoming service at a fused disconnect switch.

2. Motor rotation was set at the factory. Check the rotation of the motor shaft (CW when viewed from rear of motor). For three phase machines, reversing the motor direction is done in the control cabinet by reversing the wires L1 and L2 on the disconnect side of the main electrical connection block. For single phase machines, motor rotation is changed at the motor connection plate on the rear of the single phase motor.

INSTALLATION

Figure 2a

Straight-Through Configuration

Figure 2b

Corner Configuration

Figure 2

Changing the Track Assembly

Electrical Connections (cont’d)

3. A knock-out is provided at the rear of the top mounted control cabinet for the electrical service connection. A single source electrical connection has been provided. A fused disconnect switch or circuit breaker (supplied by others) is required to protect each power supply circuit.

Plumbing Connections

CAUTION:

Plumbing connections must comply with local sanitary and plumbing codes.

Water Connections

1. Connect the hot water supply using a 3/4” NPT connection. The connection point is located behind the lower front panel of the dishwasher. Supply enters from underneath the machine.

2. Minimum incoming water supply temperature requirements are listed below: D-HB with built-in 40°F/23°C rise electric booster (Minimum 140°F/60°C)

(Min./Max. flow pressure 20-22 psi/138 Kpa) D-HB with built-in 70°F/39°C rise electric booster (Minimum 110°F/43°C)

(Min./Max. flow pressure 20-22 psi/138 Kpa) D-H1 without built-in booster (Minimum 180°F/70°C)

(Min./Max. flow pressure 20-22 psi/138 Kpa) D-LF (Minimum 120°F/49°C - 140°F/60°C Optimum)

(Min./Max. flow pressure 20-22 psi/138 Kpa)

3. A manual shut-off valve for steam and water (supplied by others) should be installed in supply line to allow for servicing of the machine. The shut-off valve should be the same size or larger than the supply line.

INSTALLATION

11"

[280mm]

FLOOR

11"

[280mm]

FLOOR

D-HB

D-H1, D-LF

Figure 3

D-HB

3/4” NPT Water Supply Connection

Behind Front Panel

Figure 4

D-H1, D-LF

3/4” NPT Water Supply Connection

Behind Front Panel

Water Connections (cont’d)

4. A 3/4" Pressure Regulating Valve (PRV), should be installed on the incoming water supply line if water flow pressure exceeds 20-22 psi/138 Kpa. A PRV is standard equipment on Model D-HB. A PRV is not standard equipment on Models D-H1 and D-LF. The PRV may be obtained locally or direct from Champion.

Drain Connections

Refer to Fig. 5 for the location of the machine drain.

1. Models D-HB, D-H1, and D-LF are GRAVITY DRAIN machines equipped with a 1-1/2" hose connection point.

• Drain height for ALL MODELS must not exceed 11" [280mm] above floor level.

WARNING:

Connection of the machine to a drain line higher than the machine drain height will prevent the machine from draining properly.

Ventilation

NOTE:

Ventilation must comply with local sanitary and plumbing codes.

CAUTION:

Exhaust air should not be vented into a wall, ceiling, or concealed space of a building. Condensation can cause damage.

INSTALLATION

Figure 5

D-HB, D-H1, D-LF

1-1/2" Drain Connection

Lower Center of Machine

1-1/2" Drain Connection

11” [280mm] above floor level

Chemical Connections

NOTE:

Consult a qualified chemical supplier for your chemical needs.

Models D-HB, D-H1 and D-LF

1. Refer to Fig. 6 Labeled chemical signal connection points are provided inside the control cabinet for chemical dispensing equipment (supplied by others).

Detergent

1. Refer to Fig. 7

Two removable black plugs, located on the rear and left side of the wash tank are provided as detergent equipment insertion points.

INSTALLATION

Figure 6

D-HB, D-H1, D-LF

Chemical Connection Points

Left Side Interior of Control Cabinet

Signal connection points include:

• Detergent signal 120VAC between Wire #10 and Wire #2

(1 AMP MAX AMP LOAD)

• Rinse Aid/Sanitizer signal 120VAC between Wire #15 and Wire #2

(1 AMP MAX AMP LOAD)

1/2" Black Removable Plug

Detergent Sensor Point

Figure 7

D-HB, D-H1, D-LF

Wash Tank Detergent Equipment

Insertion Points

1/2" Black Removable Plug

Detergent Injection Point

5 6

CAUTION

120V SUPPLY DISPENSERS ONLY

RINSE/SANI

COMMON

RETURN

DETERGENT

18 19 15

Chemical Connections (cont’d)

Detergent (cont’d)

2. Detergent may be added manually if dishwasher is not equipped with dispensing equipment. Consult your chemical supplier for recommended amounts.

Rinse Aid/Sanitizer

Model D-HB and D-H1 Refer to Fig. 8

1. A rinse aid injection point is provided via a 1/4" NPT plug located in the final rinse piping. The plug is located in a cross fitting on the outlet side of the vacuum breaker. The vacuum breaker is located behind the control cabinet at the top of the machine.

2. Use a liquid rinse aid.

NOTE:

Models D-HB and D-H1 do not require sanitizer.

INSTALLATION

Figure 8

Rinse aid Insertion Point

D-HB, D-H1 Only

1/4" NPT plug

Rinse aid Injection Point

Chemical Connections (cont’d)

Rinse Aid/Sanitizer (cont’d)

Model D-LF Refer to Fig. 9

2. Use a liquid rinse aid.

3. A sanitizer injection point is provided via a 1/8" NPT plug located in the final rinse piping. The plug is located in a cross fitting on the outlet side of the vacuum breaker. The vacuum breaker is located behind the control cabinet at the top of the machine.

4. Use a sodium hypochlorite (Chlorine) based sanitizer at a minimum concentration of 50PPM in the final rinse. Use chlorine test papers to verify and monitor the 50PPM chlorine level.

WARNING:

Never premix rinse aid with the sanitizing agent. Mixing may cause hazardous gases to form.

CAUTION:

Some metal, including silver, aluminum, and pewter are attacked by sodium hypochlorite (chlorine sanitizer). Avoid cleaning these metals in a D-LF dishwasher.

INSTALLATION

Figure 9

D-LF

Rinse Aid/Sanitizer Injection Points

1/4" NPT plug

Rinse aid injection point

1/8" NPT plug

Sanitizer injection point

INITIAL START-UP

After plumbing and electrical connections are completed, follow the steps below to place your machine in service.

Model D-HB

, D-H1 and D-LF

Refer to Figs. 10 and 11 below.

1. Remove any foreign material from inside the machine. Make sure scrap screens are in place.

2. Make sure drain lever assembly is closed.

3. Close the Door.

4. Turn the water and main power sources to the dishwasher ON.

5. Flip the Power switch to the ON position. The “power on” light will illuminate and the machine will automatically fill with water.

6. Check the machine for leaks.

7. Push the Green Start Button to check automatic cycle.

8. Check pump motor rotation. Rotation is CW when viewed from rear of motor.

9. If machine checks okay, lift the drain lever assembly to drain machine.

10. Flip the power switch to OFF.

INITIAL START-UP

WASH RINSE

Champion

OFF

TURN OFF POWER BEFORE

SERVICING MACHINE

WARNING!

CYCLE

POWER

START

Figure 10

Operator Controls

Top Mounted Control Cabinet

Figure 11

Door Activated

Drain Lever Assembly

Main power switch

circuit breaker

Green pushbutton

start switch

Green in cycle lite

Pressure gauge

Temperature Gauges

Drain lever assembly

DOOR

OPERATION

Model D-HB, D-H1 and D-LF

1. Close the door and flip power switch ON Power light illuminates. Tank fills automatically and tank heat comes on.

2. Monitor wash tank temperature gauge Wait for temperature reading to reach Min. 150°F/66°C (D-HB, D-H1 Only) Temperature reading must be Min.120°F-140°F/49°C-60°C Optimum (ForD-LF Only)

3. Prescrap and load ware into rack Place dishes edgewise in peg rack, cups and bowls upside down in flat rack, and silverware spread evenly in single layer in flat rack.

4. Open door, insert rack

5. Close door, Push Green start button Green cycle light will illuminate. Automatic cycle begins.

Machine washes for 45 sec., then pauses for 1 sec.

6. During Final Rinse monitor pressure Machine final rinses for 14 sec. Pressure

gauge and final rinse temperature gauge reading must read between 20-22 PSI. gauge Temperature gauge must read

180-195°F/82-91°C (D-HB, D-H1 Only) Min. 120°-140°F/49°C-60°C Optimum (D-LF Only)

7. 60-second cycle complete Green cycle light goes out.

8. Open door, remove clean rack Insert another rack of soiled ware.

9. After each meal period or every two Lift drain lever assembly to drain

hours operation machine. Flush interior and clean scrap

screens and pump intake strainer. Check spray arms and clean if necessary.

NOTE:

Opening the door at any time during the cycle will stop the machine. Closing the door and pushing the Green start button will resume the cycle where it left off.

OPERATION

MAINTENANCE

Cleaning your machine is the best maintenance that you can provide. Components that are not regularly flushed and cleaned do not perform well.

The Maintenance intervals shown in the following schedules are the minimum requirements necessary for the proper performance of your machine. Maintenance intervals should be shortened whenever your machine is faced with abnormal working conditions, hard water, or multiple shift operations.

Maintenance Schedule

CLEANING

• Every 2 Hours or After Each Meal Period

Model D-HB

, D-H1, and D-LF

1. Flip the power switch OFF.

2. Lift drain lever, drain the machine.

3. Flush tank interior with fresh water.

4. Remove and clean the scrap screens. Clean the pump intake screen.

5. Inspect the spray arm nozzles and rinse nozzles. Clean if necessary.

6. Close door, flip power switch ON to refill machine.

• Every 8 Hours or at the End of the Day

Model D-HB, D-H1, and D-LF

1. Flip the power switch OFF.

2. Lift drain lever, drain the machine.

3. Flush tank interior with fresh water.

4. Remove and clean the scrap screens. Clean the pump intake screen.

5. Remove the spray arms.

6. Clean and inspect the spray arm bearings.

7. Flush the wash arm and rinse arm assemblies and nozzles.

8. Back flush the scrap screens and pump intake strainer.

9. Thoroughly clean the exterior of the machine. DO NOT HOSE DOWN WITH WATER.

10. Reassemble the machine. Leave the door open to aid overnight drying.

CAUTION:

DO NOT LEAVE WATER IN WASH TANK OVERNIGHT

MAINTENANCE

DELIMING

Your dishwasher should be delimed regularly depending on the mineral content of your water. Inspect the machine interior for mineral deposits and use a deliming solution for the best cleaning results.

NOTE:

Consult your chemical supplier for an appropriate deliming solution.

WARNING:

Deliming solutions or other acids must not come in contact with household bleach (sodium hypochlorite) or any chemicals containing chlorine, iodine, bromine, or fluorine. Mixing will cause hazardous gases to form. Skin contact with deliming solutions can cause severe irritation and possible chemical burns. Consult your chemical supplier for specific safety precautions.

DELIMING PROCESS

Model D-HB, D-H1, and D-LF

1. Remove all dishes from machine.

2. Remove any chemical pick-up tubes from their containers.

3. Place each tube in a container of fresh water and prime the chemical lines for several minutes to thoroughly flush chemical from the lines. Leave pick-up tubes out of their containers.

4. Drain the machine and refill with fresh water.

5. Spray interior walls with delimimg solution and let sit for 5 or 10 minutes depending on amount of build-up. Add deliming solution to wash tank. Do not let chemicals sit for longer than 15 minutes.

6. Push the Green start button and run an automatic cycle.

7. Repeat Steps 3-4 if necessary.

8. Lift the drain lever assembly and drain the machine.

9. Refill the machine and run a complete cycle two additional times. Drain and refill the machine after each cycle to thoroughly flush any deliming solution from the interior of the machine.

10. Flip the power switch to OFF.

11. Drain machine.

12. Deliming is complete.

MAINTENANCE

+ 48 hidden pages