Loading...
® Models NLS1, NLS2, NLS1C & NLS2C
Wireless Portable Intercom - Extreme Range
Overview
The Intercom has up to a 1000 foot (300 m) range and allows multiple simultaneous conversations, using a 900 MHz secure digital radio link. The intercoms
form an exclusive network and respond only to other intercoms in the network.
Carton Inventory
HOLD
OFF
VOLUME |
|
|
||
|
|
MONITOR |
Rubber Pads |
|
ACTIVE |
|
|
||
TALK |
|
CHANNEL |
Models NLS1 & NLS1C (1) |
|
1 |
3 |
NLS2 & NLS2C (2) |
||
|
||||
2 |
4 |
|
||
Intercom
Models NLS1 & NLS1C (1)
NLS2 & NLS2C (2)
Operation & Features
|
Channel |
Talk |
Active Light |
Channel |
Lights |
Button |
Speaker |
Select Button |
|
|
|
|
|
|
Monitor |
4 |
2 1 |
TALK |
|
E |
|
|
3 |
|
ACTIV |
|
||||
|
|
|
|
||||
Button |
|
|
|
|
|
ME |
|
|
|
MON |
|
OLUV |
OFF |
D |
|
|
|
|
TORI |
|
HOL |
|
|
AC Adapter |
|
Dipswitch #1 |
Learn Button |
Dipswitch #2 |
|
|
|
Volume
DOWN
Button
Volume
UP
Button
On/Off: To turn intercom ON, press Talk button. To turn intercom OFF, hold down the Volume DOWN button for 3 seconds.
Talk Button: To talk, hold down
the Talk button. All intercoms in |
HOLD |
|
|
OFF |
VOLUM |
E |
|
the network that are on the same |
ACTIVE |
|
|
|
|
||
|
|
MONITOR |
|
channel will receive the signal. |
|
|
|
Release the Talk button when done |
|
|
|
talking and within 10-15 seconds |
|
|
|
press and hold the Talk button of a |
|
|
|
different intercom to make a secure channel between the two. Once the channel is made the other intercoms in the network cannot hear the conversation.
Volume: Pressing the Volume DOWN button will lower the volume and pressing the Volume UP button will increase the volume.
Channel Select Button: Press the Channel Select button to set intercom to one of four secure channels or the paging channel.
The default channel for the intercom is the paging channel where all four channel lights are lit. An intercom on a channel can only hear an intercom on the same channel or on the paging channel.
|
HOLD |
|
|
|
|
|
OFF |
|
E |
|
|
|
VOLUM |
|
|
||
|
|
|
|
||
ACTI |
VE |
|
|
|
|
|
|
|
|
|
|
TALK |
|
|
MONITOR |
||
|
1 |
CHA |
NNE |
L |
|
|
|
||||
|
3 |
|
|
||
|
2 |
|
|
|
|
|
4 |
|
|
|
|
Battery: The AA Alkaline batteries |
|
(not provided) will last up to a year |
|
depending on use. When batteries |
|
are low intercom will emit three |
|
beeps every ten minutes. |
|
A DC Adapter (not provided) can |
|
also be used to power the intercom. |
|
In this case, the channel lights will |
OPTIONAL |
remain on. |
|
Conference Mode: Conference Mode allows multiple intercoms to participate in a conversation compared to Normal Mode in which only two intercoms
can communicate. All intercoms must be set to the same channel or the paging channel
to be in Conference Mode. To put intercom 1 2 in Conference Mode set Dipswitch #2 to UP
position.
Monitor Mode: Monitor Mode is used to monitor the noise in a
specific room. Place the intercom |
|
HOLD |
|
|
|
|
OFF |
|
E |
|
|
|
VOLUM |
|
|||
|
|
|
|||
ACTI |
VE |
|
|
|
|
|
|
|
|
||
in the room that is to be monitored |
TALK |
|
|
|
|
|
|
|
|
|
|
and press the Monitor button until |
|
1 |
CHA |
NNE |
|
|
3 |
|
|||
|
2 |
|
|
|
|
|
4 |
|
|
|
|
|
|
|
|
|
|
a tone is heard. For extended Monitor usage, consider using a
plug-in transformer. Any other networked intercom can listen to that room. If a specific channel is selected
for Monitor Mode then only other intercoms on that channel or on the paging channel can listen. Press the Talk button to exit Monitor Mode. A tone will be heard indicating Monitor Mode is no longer active.
Voice Activation Mode (VOX): Voice Activation Mode (VOX) allows a call to be answered without pressing the Talk button. Once a call is heard on an intercom which has been set to VOX, a response can be given by speaking loudly into the intercom. There will be a slight delay when VOX is first activated by a voice,
but will continue to transmit audio until the |
|
speaking stops. To put intercom into VOX, |
|
place Dipswitch #1 to the UP position. While |
|
in VOX mode, a call may be initiated by |
1 2 |
pressing the TALK button. |
|
1
Assemble Intercom
Step 1
Install 4 AA Alkaline batteries (not provided).
Step 2
INTERCOM |
LEARN MODE |
|
Press the Learn button |
OR |
until a beep is heard. |
|
Each intercom will emit a tone when entering programming mode. It may take up to 3-1/2 minutes for a secure network to be established. Repeat for any additional intercoms.
Add to an Existing Network
4 |
2 1 |
TALK |
|
|
3 |
|
CTIVE |
TORI |
OLUME HOLD |
|
V OFF |
MON |
|
Adhere rubber pads to bottom. Repeat Steps 1 and 2 for any additional intercoms.
Programming Intercom
The intercom must be programmed to at least one other intercom to become a network or it can be programmed into an existing network.
Create New Network
Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put any networked intercom into Learn Mode (refer to table below).
INTERCOM |
LEARN MODE |
|
Press the Learn button |
OR |
until a beep is heard. |
|
Each intercom will emit a tone when entering Programming Mode. It may take up to 3-1/2 minutes for a secure network to be established. Repeat for any additional intercoms.
NOTE: Do not program new intercoms to each other before adding them to the network or they will form a separate network and the memory will need to be cleared.
4 |
2 |
1 |
TALK |
|
|
|
|
||
3 |
|
|
|
|
|
||||
|
|
|
|
|
|
ACTIVE |
|
|
|
|
|
|
TORI |
OLUME |
|
HOL |
|
||
|
|
|
|
|
|
V |
OFF |
|
D |
|
|
MON |
|
|
|
|
|
|
|
|
HOLD |
|
|
OFF |
E |
|
VOLUM |
|
|
|
|
AC |
TIVE |
|
|
|
MONITOR
Before programming, clear memory on all intercoms. Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put the second intercom into Learn Mode (refer to the following table).
Press and release the Talk button to verify network is complete.
2
Loading...