Chamberlain HD620EV, WD832KEV User Manual

Download

Page 1

[] Please readthis manual andthe enclosed safety materials carefully!

[] Fastenthe rnannal nearthe garagedoor after installation.

[] The door WILL NOT CLOSEunlessthe ProtectorSystem®is connectedand

properlyaligned.

[] Periodicchecks ofthe garage dooropener are requiredto ensure safe operation.

[] The model numberlabel is located onthe left side panel ofyour garage

door opener.

[] This garage door opener is compatible with IViyO® and Secnrity÷ 2.0TM accessories.

[] {DONOT enable the Timer-to-Close feature ifyon are installing the garage door

opener on a one-piece door, TheTimer-to-Close is to be nsed ONLY with sectional doors.

Write down the following information for future reference:

SerialNumber:

Date of Purchase:

I / / {

ot os

www.charnberlain.corn

The Chamberlain Group, Inc.

845 Larch Avenue

Eimhurst, Illinois 60126-1196

Page 2

Safety Symbol and Signal Word Review

Thisgaragedooropenerhasbeendesignedandtestedto offersafeserviceprovideditisinstalled, operated,maintainedand testedinstrictaccordancewiththe instructionsandwarningscontainedinthis manual.

WhenyouseetheseSafetySymbolsand SignalWordsonthefollowingpages,theywillalertyoutothe possibilityofseriousinjury ordeathifyoudonotcomplywiththewarningsthataccompanythem.The hazardmaycomefromsomethingmechanicalorfromelectricshock.Readthe warningscarefully.

Mechanical

Electrical

WhenyouseethisSignalWord onthe followingpages,itwillalertyoutothepossibilityofdamageto yourgaragedoorand/orthe garagedoor opener ifyoudo not complywiththecautionarystatementsthat accompanyit.Readthemcarefully.

Checkthe Door

TopreventpossibleSERIOUSINJURYor DEATH:

• ALWAYScallatraineddoorsystemstechnicianifgaragedoorbinds,sticks,or isout of balance. AnunbalancedgaragedoormayNOTreversewhenrequired.

• NEVERtrytoloosen,moveoradjustgaragedoor, doorsprings,cables,pulleys,bracketsortheir hardware,ALL ofwhichareunderEXTREMEtension.

• DisableALLlocksand removeALL ropesconnectedtogaragedoorBEFOREinstallationand operatinggaragedooropenertoavoidentanglement.

ALWAYSdisablelocksBEFOREinstallingandoperatingtheopener. ONLYoperategaragedooropenerat120V,60 Hztoavoid malfunctionanddamage.

1. Disablelocksandremoveanyropesconnectedtothe garagedoor.

2. Liftthedoorhalfwayup.Releasethedoor. Ifbalanced,itshouldstayin place,supportedentirelybyitssprings.

3. Raiseandlowerthedoorto checkforbindingor sticking.Ifyourdoor binds,sticks,or isoutofbalance,callatraineddoorsystems

technician.

4. Checkthe sealon the bottomofthe door.Any gap betweenthefloor andthe bottomofthedoormustnotexceed1/4inch(6mm). Otherwise,thesafetyreversalsystemmaynotworkproperly.

5. The openershouldbe installedabovethecenterofthe door. Ifthere is atorsionspringor centerbearingplateinthe wayoftheheader bracket,itmaybe installedwithin4feet(1.2m)to the leftor rightofthe doorcenter.Seepage12.

Torsion Extension Spring OR Spring

Page 3

Additional ItemsYou May Need:

Surveyyourgarageareato seeifyouwillneed anyofthefollowingitems:

• (2)2X4 PIECESOFWOOD Maybeusedto fastentheheaderbrackettothestructuralsupports.Alsousedtopositionthe garagedooropenerduringinstallationandfortestingthesafetyreversingsensors.

• SUPPORTBRACKETANDFASTENINGHARDWARE Mustbeusedifyouhaveafinishedceilingin yourgarage.

• EXTENSIONBRACKETS(MODEL41A5281)ORWOODBLOCKS Dependingupongarage construction,extensionbracketsorwoodblocksmaybeneededto installthesafetyreversingsensor.

• FASTENINGHARDWARE Alternatefloor mountingofthesafetyreversingsensorwillrequirehardwarenotprovided.

• OUTSIDEQUICKRELEASE(MODEL7702CB) Requiredfora garagewithNOaccessdoor.

• DOORREINFORCEMENT Requiredifyouhavealightweightsteel,aluminum,fiberglassorglasspaneldoor.

• RAILEXTENSIONKIT Requiredifyourgaragedoor ismorethan7 feet (2.13m)high.

Tools Needed

5/32

3/16

5/16_

I/25/80 0 0 LJl/4

7/16 9/16

Page 4

CartonInventory

Your garage door opener ispackaged in one carton which contains the motor unit and all parts illustrated below. Accessories vary depending on the garage door opener model purchased. Depending on your model, other accessories may be included with your garage door opener. Instructions for these accessories will be attached tothe accessory and are not included in this manual. Ifanything is missing, carefully check the packing material. Hardware for assembly and installation is shown on the next page. Save the carton and packing material until the installation and adjustment is complete. The images throughoutthis manual are for reference only and your product may look different.

A. Headerbracket B. PulIey

C. Doorbracket D. Carveddoor arm

E. Straightdoorarm

(Packagedinsidefront rail section)

F. Trolley

NOTE: Besuretoassemblethetrolleybeforesliding ontorail.

G. Emergencyreleaseropeand handle H. Rail (1frontand4 centersections)

I. Hangingbrackets (2)

(Packagedinsidethe frontrailsection)

J. Garagedooropener(motorunit)

K. Sprocketcoverandscrews

L. "U"bracket M. Belt N. Doorcontrol O. Remotecontrol

P. The ProtectorSystem®

Safetyreversingsensors with 2 conductorwhite andwhite/blackwire attached:SendingSensor(1), ReceivingSensor(1), andSafety SensorBrackets(2)

NOT SHOWN

Whiteandred/white wire Owner'smanual

Page 5

HardwareInventory

Bolt 1/4"-20xl-3/4"

ASSEMBLYHARDWARE

LockNut 1/4"-20

Lock Washer 3/8"

Nut 3/8"

Bolt

Hex Screw #8x3/8" (2) (packed with the sprocket cover)

Clevis Pin 5/16"x1-1/2"

Carriage Bolt

' (2)

Nut

5/16"-18 (6)

Drywall Anchors (2)

INSTALLATIONHARDWARE

Self-Threading Screw 1/4"-14x5/8" (2)

Wing Nut 1/4"-20 (2)

.................................!.....................................!........................................................!l!

Clevis Pin 5/16"x1-1/4" O1 IJj'4q Clevis Pin 5/16"x1"0 1

Hex Bolt 5/16"-18x7/8" (4)

Lock Washer 5/16"-18 (5) Ring Fastener (3)

DOOR CONTROLHARDWARE

Screw 6-32x1" (2)

Screw 6ABxl" (2)

Insulated Staples (Not Shown)

Page 6

STEP 1 Assemble the rail and trolley

TopreventINJURYfrompinching, keephandsandfingersawayfromthejointswhile assemblingthe rail.

Toavoidinstallationdifficulties,donotrunthegaragedooropeneruntilinstructedtodoso. Thefrontrailhasacutout"windod' atthe doorend(see illustration).Theholeabovethiswindowis

largeronthetopof the railthanonthe bottom.A smallerhole3-1/2"(8.9cm)awayis closetotherail edge.Rotatethebackrail soit hasa similarholeclosetotheoppositeedge,about4-3/4"(12 cm)from

thefarend.

1. Removethestraightdoor armandhangingbracketpackagedinsidethefrontrailand set asideforInstallationStep5and 9.NOTE: TopreventINJURYwhileunpackingtherail

carefullyremovethestraightdoor armstoredwithintherailsection.

2. Alignthe railsectionson a flatsurfaceasshownand slidethetaperedendsintothe larger ones.Tabsalongthesidewill lockintoplace.

3. Placethemotoruniton packingmaterialtoprotectthecover,andrestthebackendoftherail ontop. Forconvenience,putasupportunderthe frontend oftherail.

4. Asa temporarystop,insertascrewdriverintothe hole 10"(25cm)fromthefrontendoftherail, asshown.

5. Checkto be surethereare4plasticwearpadsinsidethe innertrolley.Iftheybecameloose duringshipping,checkallpackingmaterial.Snapthembackintopositionasshown.

6. Slidethetrolleyassemblytowardthescrewdriverasshown.

7. Slidethe railontothe "U"bracket,untilit reachesallthestopsonthetopandsidesofthe "U" bracket.

Inner Trolley

Wear Pads

FrontRail

Section

(TO DOOR)

Trolley,

Rail Tal

Window Cut-Out

To garage

dooropener (TO MOTORUNIT)

SLIDE TO STOPS ON TOPAND SIDES OF "U"BRACKET

Page 7

STEP 2 Fastenthe rail to the motor unit

ToavoidSERIOUSdamageto garage dooropener,useONLYthosebolts/fastenersmountedinthe topofthe opener,

1, Inserta 1/4"-20xl-3/4"boltintothecoverprotectionboltholeonthebackendofthe railas

shown,Tightensecurelywitha 1/4"-20locknut,DoNOTovertighten,

2, Removetheboltandnutfromthetop ofthe motor unit, 3, Usethecartonto supportthefrontendofthe rail, 4, Placethe"U"bracket,flat sidedownontothemotorunitandalignthebracketholes withthe

boltholes,

5, Fastenthe"U"bracketwiththepreviouslyremovedboltandlocknut;DONOTuseanypower

tools,Theuseofpowertoolsmaypermanentlydamagethegaragedooropener,

HARDWARE

Bolt and Nut

)_ (Mounted in the

garage door opener)

Bolt 1/4"-20xl -3/4" _Lock Nut 1/4"-20

Bolt

Lock Nut -_

Bolt 1/4"-20x1-3/4""U" Bracket _ _t

Cover Protection

Bolt Hole

I I

LockNut1/4"-20

Page 8

STEP

3 Installthe idler pulley

Laythebeltbesidetherail,asshown.Grasptheendwiththe hookedtrolleyconnectorand passapproximately12"(30 cm)of beltthrough thewindow.Keeptheribbedsidetowardthe rail,andallowittohang untilAssemblyStep4.

2. Removethetape fromthe idlerpulley.Theinsidecentershouldbe pre-greased.Ifdry, regreasetoensureproperoperation.

3. Placetheidlerpulleyintothewindowasshown.

4. Inserttheidler boltfromthetopthroughtherail andpulley.Tightenwitha3/8"lockwasherand nutunderneaththerail untilthe lockwasheris compressed.

5. Rotatethepulleyto be sureit spinsfreely.

6. Locatethe railtab.The railtabisbetweentheidlerboltand thetrolleyinthefront railsection. Useaflathead screwdriverandlifttherailtab untilthetabisvertical(90°).

HARDWARE

Bolt

_ LookWasher 3/8'

Nut 3/8"

Lock Washer 3/8"

Nut 3/8"

CORRECT

iNCORRECT

Grease Inside Pulley

Idler Pulley

Trolley Connector

Page 9

STEP

4 Install the belt

Pullthe beltaroundtheidlerpulleyandtowardthetrolley.Theribbedside mustcontactthe pulley. Hookthetrolleyconnectorintothe retainingsloton thetrolley.(a) Withthetrolleyagainstthescrewdriver,dispensetheremainderofthe beltalongtherail

towardthemotorunitaroundthesprocket.Thesprocketteethmustengagethebelt.(b) Threadtheinnernutandlockwasherontothetrolleythreadshaft(c). Checktomakesurethe

beltisnottwisted. Insertthetrolleythreadedshaftthroughtheholeinthetrolley.Be surethebeltisnot

twisted.(c)

Looselythreadtheouternutontothetrolleythreadedshaft. Removethescrewdriver.

Pulley

Outer Nut

Sprocket

Inner

Lock Nut

Washer

Lded

Shaft

Page 10

STEP 5 Tighten the belt and installthe sprocketcover

ALWAYSkeephandclearofsprocketwhileoperatingopener, SecurelyattachsprocketcoverBEFOREoperating,

1, Spinthe innernutandlockwasherdownthetrolleythreadedshaft,awayfromthetrolley 2, Totightenthebelt,turnouternut inthedirectionshownuntilthe lineonthespringretainer

plateisvisible,Besurethebeltis nottwisted,andthe ribbedsidefacesthe rail,

3, Tightentheinnernuttosecuretheadjustment,Thissetsthespringto optimumbelttension, 4, Positionthe sprocketcoveroverthe sprocketasshownandfastentothe mountingplatewith

8x3/8"hexscrewsprovided,

Youhavenowfinishedassemblingyourgaragedooropener.Pleasereadthefollowingwarnings beforeproceedingtotheinstallationsection.

HARDWARE

HexScrew#8x3/8" (Packedwiththe sprocketcover)

Outer Nut Spring Retainer

Inner Nut

CORRECT

iNCORRECT

LockWasher

Line

f t----- HexScrew#8x3/8"

- SprocketCover

Page 11

Installation

IMPORTANTINSTALLATIONINSTRUCTIONS

ToreducetheriskofSEVEREINJURYorDEATH:

1. READANDFOLLOWALLINSTALLATIONWARNINGSAND INSTRUCTIONS.

2. Installgaragedoor openerONLYonproperlybalancedandlubricatedgaragedoor.An improperlybalanceddoormayNOTreversewhenrequiredandcouldresultinSEVERE INJURYor DEATH.

3. ALL repairstocables,springassembliesandotherhardwareMUSTbemadebyatrained doorsystemstechnicianBEFOREinstallingopener.

4. DisableALLlocksand removeALL ropesconnectedtogaragedoorBEFOREinstalling openertoavoidentanglement.

5. Installgaragedoor opener7feet(2.13m)or moreabovefloor.

6. Mounttheemergencyreleasewithinreach,butatleast6feet(1.83m)abovethefloorand avoidingcontactwithvehiclestoavoidaccidentalrelease.

7. NEVERconnectgaragedoor openerto powersourceuntil instructedtodoso.

8. NEVERwearwatches,ringsorlooseclothingwhileinstallingorservicingopener.Theycould becaughtin garagedoor or openermechanisms.

9. Installwall-mountedgaragedoorcontrol:

• withinsightofthe garagedoor.

• outofreachofchildrenat minimumheightof5feet(1.5m).

• awayfromALLmovingpartsof thedoor.

10. Placeentrapmentwarninglabelonwallnextto garagedoor control.

11. Placemanualrelease/safetyreversetestlabelin plain viewon insideofgaragedoor.

12. Uponcompletionofinstallation,testsafetyreversalsystem.DoorMUSTreverseoncontact witha 1-1/2"(3.8cm)highobject(or a2x4laidflat)onthefloor.

13. To avoidSERIOUSPERSONALINJURYor DEATHfromelectrocution,disconnectALL electricpowerBEFOREperforminganyserviceor maintenance.

14. DONOTenabletheTimer-to-Clocefunctionalityifoperatingeitherone-pieceorswinging garagedoors.TobeenabledONLYwhenoperatingasectionaldoor.

Page 12

Installation

STEP 1 Determinethe headerbracketlocation

To preventpossibleSERIOUSINJURYorDEATH:

• HeaderbracketMUSTbe RIGIDLYfastenedtostructuralsupportonheaderwallor ceiling, otherwisegarage doormightNOTreversewhenrequired.DONOTinstallheaderbracketover drywall.

• ConcreteanchorsMUSTbe usedif mountingheaderbracketor 2x4intomasonry.

• NEVERtrytoloosen,moveoradjustgaragedoor,springs,cables,pulleys,brackets,or their hardware,ALLofwhichare underEXTREMEtension.

• ALWAYScalla traineddoorsystemstechnicianifgarage door binds,sticks,orisoutof balance. AnunbalancedgaragedoormightNOTreversewhenrequired.

Installationproceduresvaryaccordingto garagedoor types.Followtheinstructionswhichapplytoyour door.

1. Closethedoorandmarktheinsideverticalcenterlineofthegaragedoor.

2. Extendthe line ontotheheaderwallabovethedoor.

Youcanfastentheheaderbracketwithin4feet (122 m) ofthe left orrightofthedoor centeronlyifa torsionspringor centerbearingplateisintheway; oryoucanattachitto theceilingwhenclearanceisminimal (It maybemountedonthewallupsidedownif necessary,to gainapproximately1/2"(1cm).

Ifyouneedtoinstalltheheaderbracketon a 2x4 (onwallorceiling),uselagscrews(not provided)tosecurelyfastenthe2x4tostructuralsupports.

3. Openyourdoortothehighestpointoftravelasshown.Drawanintersectinghorizontallineon theheaderwall2" (5 cm)abovethe highpoint:

• 2" (5cm)abovethe highpointfor sectionaldoorand one-piecedoorwithtrack.

• 8" (20cm)abovethe highpointforone-piecedoorwithouttrack.

Thisheightwillprovidetravelclearanceforthetop edgeofthedoor.NOTE:Ifthetotalnumberofinches

exceedstheheightavailableinyourgarage,usethemaximumheightpossible,orrefertopage !2 for ceilinginstallation.

Header Wall

Vertical Centerline of Garage Door

2x4 Structural

Supports

OPTIONAL CEILING MOUNT

FORHEADER BRACKET

J Header Wall "777,----1 2' (5 ore)

_Track

Highest Point

of Travel

-----Door

(5 cm)

Track

Highest Point of Travel

Sectional door with curved track

ij_______eaderWall I_1_ 8" (20cm)

Door I_-

_._r_ _Highest

__'_ Pointof

II 1Travel

Hardware /

One-piecedoerwithouttrack:

jambhardware

One-piecedoorwithhorizontaltrack

_ HeaderWall

8"(20 cm)

_/_ _,",,_ HgUest

Door

"'_ "_\ il Pointof

4 r ve'

L_/ ' Pivot

One-piecedoorwithouttrack:

pivothardware

Page 13

Installation

STEP 2 Install theheader bracket

Youcanattachtheheaderbracketeithertothewallabovethegaragedoor,orto theceiling.Followthe instructionswhichwill workbestforyourparticularrequirements.Donotinstallthe headerbracket over

drywall.Ifinstallingintomasonry,useconcreteanchors(notprovided).

HARDWARE

Screw5/16"-9xl-5/8" _[_

Lag

'--U

WALL INSTALLATION

1. Centerthebracketon the verticalcenterlinewiththebottomedgeofthe bracketon the horizontallineasshown.

2. Marktheverticalsetofbracketholes.Drill3/16"pilotholesand fastenthebracketsecurelytoa structuralsupportwiththehardwareprovided.

WallMount

OptionalMounting

Holes

(Header Wall)

2x4 Structural Support

Highest Point _ /

of Garage

DoorTravel

Vertical

GarageDoor

-'_ LagScrew

i" 5/tB"-gxl-5/8

DoorSpring

(Garage Door)

CEILING INSTALLATION

1. Extendthe verticalcenterlineonto theceiling asshown.

2. Centerthebracketon the verticalmark,nomorethan6" (15cm)fromthewall. Makesurethe arrow ispointingawayfromthewall.The bracketcanbemountedflushagainsttheceiling

whenclearanceisminimal.

3. Markthesideholes.Drill3/16"pilotholesandfastenbracketsecurelyto a structuralsupport withthe hardwareprovided.

CeilingMounting

Holes

6" (15 cm) Maximum

Door Spring

(FinishedCeiling)

Vertical

Centerline of GarageDoor

Lag Screw 5/16"-9xl-5/8"

(Header Wall)

Page 14

Installation

STEP 3 Attachthe rail to the headerbracket

1. Alignthe railwiththeheaderbracket.Inserttheclevispinthroughtheholes intheheader bracketandrail.Securewiththe ringfastener.

NOTE: Usethepackingmaterialasaprotectivebasefor thegaragedooropener.

HARDWARE

0 vis. ,l Xll,, O

Ring Fastener

STEP 4 Position the garagedoor opener

To preventdamagetogaragedoor,restgaragedooropenerrailon 2x4placedontopsedion of door.

1. Removethe packingmaterialand liftthegarage door openeronto aladder.

2. Fullyopenthe doorandplacea2x4(laidflat) underthe rail.Forone-piecedoorswithout tracks,laythe2x4onit'sside.

NOTE: A 2x4 isidealforsettingthedistancebetweentherail and thedoor.Iftheladder isnottall enoughyou willneedhelp atthispoint. Ifthe doorhitsthe trolleywhenitisraised,pullthetrolleyrelease armdowntodisconnecttheinnerand outertrolley.Slidetheoutertrolleytowardthegarage door opener.Thetrolleycanremaindisconnecteduntilinstructed.

All other door types

Page 15

Installation

STEP 5 Hangthe garagedoor opener

ToavoidpossibleSERIOUSINJURYfromafallinggarage door opener,fastenitSECURELYto structuralsupportsofthegarage.ConcreteanchorsMUSTbeusedifinstallingANYbracketsinto masonry.

Hangingthegaragedooropenerwillvarydependingonyourgarage.Belowarethreeexample installations.Yourinstallationmaybedifferent.ForALL installationsthegaragedoor openerMUSTbe connectedtostructuralsupports.Theinstructionsillustrateone oftheexamplesbelow.

FinishedCeiling ...........

Unfinished Ceiling

HARDWARE

Lock Washer 5/16"-18

_ _Nut5/16"-18

1, Onfinishedceilings,usethelagscrewstoattachasupportbracket(notprovided)tothe

structuralsupportsbeforeinstallingthegaragedooropener,

2, Makesurethe garagedoor opener isalignedwiththeheaderbracket,Measurethe distance

fromeachsideofthegaragedooropenertothesupportbracket, 3, Cutbothpiecesofthe hangingbracket(notprovided)torequiredlengths, 4, Attachthe endofeachhangingbrackettothesupportbracketwithappropriatehardware(not

provided), 5, Attachthe garagedoor opener tothe hanging bracketswiththehexbolts,lockwashers,and

nuts.

6. Removethe2x4andmanuallyclosethedoor.Ifthedoorhitstherail,raisethe headerbracket.

.... - 5/1L_ilk6"VV_h7/8"_6"-18

pnr°°tvided) Nut5/16"-1

Page 16

Installation

STEP 6 Install the light bulbs STEP 7 Attachthe emergencyreleaserope and handle

TopreventpossibleOVERHEATINGoftheend panelor lightsocket:

• UseONLYA19incandescent(100Wmaximum)or compactfluorescent(26Wmaximum)light bulbs.

• DO NOTuseincandescentbulbs largerthan 100W.

• DO NOTusecempactfluorescentlightbulbslargerthan 26W(100W)equivalent.

• DO NOTusehalogen bulbs.

• DO NOTuseshortneckor specialtylightbulbs.

1. Pullonthe top sidesofthelightlensand rotatethe lightlensdown.

2. InsertanA19incandescent(100Wmaximum)or compactfluorescent(26W,100Wequivalent) lightbulb intothelightsocket.

3. Rotatethelensuptoclose.

NOTE: Donot usahalogen,shortneck,orspecialtylightbulbsas thesemayoverheattheendpanel or lightsocket.DonotusaLEDbulbsas theymayreducetherangeorpefformanceofyourremotecontrols.

TopreventpossibleSERIOUSINJURYorDEATHfromafallinggaragedoor:

• Ifpossible,useemergencyreleasehandletodisengagetrolleyONLYwhengaragedooris CLOSED.Weakor brokenspringsor unbalanceddoor couldresultin an opendoorfallingrapidly and/orunexpectedly.

• NEVERuseemergencyreleasehandleunlessgaragedoorwayisclearofpersonsand obstructions.

• NEVERusehandletopulldoor openor closed.Ifropeknotbecomesuntied,youcouldfall.

1. Insertoneendoftheemergencyreleaseropethroughthehandle.Makesurethat"NOTICE"is rightside up.Tie a knotat least 1inch (2.5cm)fromtheend oftheemergencyreleaserope.

2. Inserttheotherendoftheemergencyreleaseropethroughthe holeinthetrolleyreleasearm. Mounttheemergencyreleasewithinreach,butatleast6feet (1.83m)abovefloor,avoiding centactwithvehiclestopreventaccidentalreleaseand securewitha knot.

NOTE: flit isnecessaryto cuttheemergencyreleaserope,sealthecutend withamatchorlighterto preventunraveling.Ensuretheemergencyreleaseropeandhandleareabovethetopofall vehiclesto avoidentanglement.

Page 17

Installation

STEP 8 Install thedoor bracket

Fiberglass,aluminumorlightweightsteelgaragedoorsWILLREQUIREreinforcementBEFORE installationofdoorbracket.Contactyourdoormanufacturerforreinforcementkit.

Figure1showsonepiece ofangleironasthehorizontalbrace.Fortheverticalbrace,2piecesofangle ironareusedtocreateaU-shapedsupport.Thebestsolutionistocheckwithyour garagedoor manufacturerfor anopener installationdoor reinforcementkit.

NOTE: Manydoorreinforcementkitsprovidefordirectattachmentof theclevispin and door arm.In this caseyouwillnotneed thedoor bracket;proceedtothenextstep.

A horizontal and vortical reinforeementis needed for

ligNweigbt garage doors (fiberglass, ataminnm, steel, doors with glass panel, otc.) (not provided).

A horizontal reinforcement brace should be long

enongb to be sennrod to two or three vortical supports.

A vertical reinforcement brace shonld cover fhe heigN

of fho fop panel.

Self-Threading Screw

1/4"-14x5/8"

HARDWARE

SECTIONAL DOORS

1. Centerthedoorbracketonthepreviouslymarkedverticalcenterlineusedforthe header bracketinstallation.NotecorrectUP placement,asstampedinsidethebracket.

2. Positionthe topedge ofthebracket2"-4"(5-10cm)belowthetopedgeofthedoor,OR directlybelowanystructuralsupportacrossthetopofthedoor.

3. Mark,drillholesandinstallasfollows,dependingon yourdoor'sconstruction:

Metalorlightweightdoorsusing a verticalangleironbracebetween thedoorpanelsupport andthedoorbracket:

• Drill3/16"fasteningholes.Securethedoorbracketusingthetwoselfthreadingscrews. (Figure2)

• Alternately,usetwo 5/16"bolts,lockwashersandnuts(notprovided).(Figure3)

Metal,insulatedorlightweightfactory reinforceddoors:

• Drill3/16"fasteningholes.Securethedoorbracketusingtheself-threadingscrews. (Figure4)

WoodDoors:

• Usetopandbottomorside to sidedoor bracketholes.Drill5/16" holesthroughthedoorand securebracketwith5/16"x2"carriagebolts,lockwashersand nuts(notprovided).(Figure5)

NOTE: The!/4"-!4xS/8"self-threadingscrewsarenotintendedforuseon wooddoors.

FIGURE2 Vertical

_ Reinforcement

Ioll_l VerticalCenterline

DoorB_'_

Self-ThreadingScrew 1/4"-14x5/8"

FmGURE3

Bolt5/16"-18x2" (notprovided)

VerticalReinforcement

VerticalCenterline ofGarageDoor

Door Bracket

Lock Washer 5/16"

Nut 5/16"-18

_ ertical

Centerline of Garage

Door

Usilf-Threading

Screw 1/4"-14x5/8"

FmGURE5 Reinforcement Board

Bolt5/16"-18x2" InsideEdgeof Dooror

(notprovided) _,__

Vear_;;'DOe_trer'ine°f_ ,_, .

Page 18

Installation

STEP 8 Install thedoor bracket (continued)

ONE-PIECE DOORS

1. Center the door bracket on the top ofthe door, in line with the header bracket as shown.

2. Mark either the left and right, or the top and bottom holes.

Metal Doors:

• Drill 3/16" pilot holes and fasten the bracket with the self-threading screws provided.

Wood Doors:

• Drill 5/16" holes and use 5/16"x2" carriage bolts, lock washers and nuts (not provided) or 5/16"xl - 1/2" lag screws (not provided) depending on your installation needs.

NOTE: The door bracket may be installed on the top edge of the door ff required for your insta//ation. (Refer to the dotted line optional placement drawing.)

HeaderWall

2x4 Support (Finished Ceiling)

For a door with no exposed framing, or for the optional installation, use lag screws

5/16"xl -1/2" (not provided) to fasten the door bracket.

Metal Door _;_j Self-Threading

Screw 1/4"-14x5/8"

Door r '_ Top of Door Bracket ', (Inside Garage)

Top Edge of

Door

Optional Placement

Wood Door _ Nut 5/16"-18

@ ,@----Lock Washer 5/16" @

Door Bracket '_,,_,' ,. _ Top of Door

-->_ (Inside Garage)

J_ _,, _-_ Top Edge

ofDoor

_\ pO_t_°enma_nt

__ Carriage Bolt 5/16"x2"

(not provided)

Page 19

Installation

STEP 9 Connectthe doorarm to the trolley

Installationwillvaryaccordingto thegaragedoortype.Followtheinstructionswhichapplytoyour door.

SECTIONAL DOORS

IMPORTANT:Thegrooveonthestraightdoor armMUSTfaceawayfromthecurveddoorarm.

1. Closethedoor.Disconnectthetrolleybypullingthe emergencyreleasehandle.

2. Attachthe straightdoorarmtotheouter trolleyusingtheclevispin.Securewiththe ring fastener.

3. Attachthe curveddoorarmtothedoorbracketusingthe clevispin.Securewiththering fastener.

4. Bringarm sectionstogether.Findtwopairsof holesthatlineupandjoin sections.Selectholes asfarapartas possibletoincreasedoorarmrigidityandattachusingthebolts,nuts,andlock

washers.

5. Pullthe emergencyreleasehandletowardthegaragedooropeneruntilthetrolleyrelease armishorizontal.Thetrolleywillre-engageautomaticallywhenthegaragedoor openeris activated.

NOTE: ffthe holes in thecurveddoorarmandthestraightdoorarmdonotalign,reversethestraight doorarm,selecttwoholes(asfarapartaspossible)andattachusingbolts, nuts,andlockwashers, ffthe straightdoorarmishangingdowntoofar,youmayout6 inches(! 5cm)from thesofidend.

ClevisPin5/16"x1-1/4"

Ring Fastener

HARDWARE

ClevisPin5/16"x1"

HexBolt5/16"-18x7/8"

_ Nut5/16"-18 _

Lock Washer

5/16" -18

_'Straight ,

DoorArm

_. (Groove

facing

ClevisPin 5/16"xl"

Hex Bolt 5/16"-18x7/8"

Pin 5/16"x1-1/4"

Page 20

Installation

STEP 9 Connectthe doorarm to the trolley (continued)

ONE-PIECE DOORS

IMPORTANT:Thegrooveonthestraightdoor armMUSTfaceawayfromthecurveddoorarm.

1. Closethedoor.Disconnectthetrolleybypullingthe emergencyreleasehandle.

2. Fastenthestraightdoorarmandthecurveddoorarmtogethertothelongestpossiblelength (witha2or 3 holeoverlap)usingthebolts,nuts,andlockwashers.

3. Attachthe straightdoorarmtothedoorbracketusingthe clevispin.Securewiththering fastener.

4. Attachthe curveddoorarmtothetrolleyusingtheclevispin.Securewiththeringfastener.

5. Pullthe emergencyreleasehandletowardthegaragedooropeneruntilthetrolleyrelease armishorizontal.

HARDWARE

ClevisPin5/16'x1-1/4" ClevisPin5/16"x1'

HexBolt5/16"-18x7/8"

RingFastener _ Nut5/16'-18 _

LockWasher

5/16"-18

CORRECT

One-Piece Doer without Track

iNCORRECT

,ClevisPin5/16"x1-1/4" '_,_

Hex Bolt5/16"-18x7/8"

One-PieceDoorwith Track

"_:_ Clevis Pin

"'%_¢,/Clevis Pin _v 5/16"x1-1/4"

Hex Bolt5/16"-18x7/8"

Page 21

Installation

STEP 10 Install the door control

TopreventpossibleSERIOUSINJURYorDEATHfromelectrocution:

• Besurepoweris NOTconnectedBEFOREinstallingdoorcontrol.

• ConnectONLYto 12VOLTlowvoltagewires. TopreventpossibleSERIOUSINJURYorDEATHfromaclosinggaragedoor:

Installdoor controlwithinsightofgarage door,out of reachofchildrenat aminimumheightof5 feet(1.5m),andawayfromALLmovingpartsofdoor. NEVERpermitchildrento operateorplaywithdoorcontrolpushbuttonsorremotecontrol transmitters.

Activatedoor ONLYwhenitcanbeseenclearly,isproperlyadjusted,andthereareno

obstructionstodoor travel.

ALWAYSkeepgaragedoor in sightuntilcompletelyclosed.NEVERpermitanyoneto crosspath

ofclosinggaragedoor.

INTRODUCTION CompatiblewithMyQ® enabledaccessories,seepage 39.Yourgaragedooropener iscompatiblewith

upto2 MyQ® doorcontrols.NOTE:OlderChamberlaindoorcontrolsandthirdpartyproductsare not

compatible.

Installthedoorcontrolwithinsightofthedoorataminimumheightof 5feet (1.5m) wheresmallchildren cannotreach,andawayfromthemovingpartsofthe door.Forgangboxinstallationsitis notnecessary

to drillholesor installthe drywallanchors.Usethe existingholesinthe gang box.

NOTE: Yourproductmaylookdifferentthantheillustrations.

HARDWARE

Screw _ Sorew ilil

6-32xt" (2) 6ABxt"(2)

DrywallAnchors(2)

4-5

1. Strip 7/16inch(11mm) of insulationfromoneendofthe wireandseparatethewires.

2. Connectonewiretoeachofthetwoscrewsonthe backofthedoorcontrol.Thewirescanbe connectedtoeitherscrew.Ifyourgarage ispre-wiredforthedoorcontrolchooseanytwo wiresto connect,notewhichwiresareusedsothe correctwiresareconnectedtothegarage door openerin a laterstep.

3. Markthelocationofthebottommountingholeand drilla5/32inch (4mm)hole.

4. Installthebottomscrew,allowing1/8 inch(3mm)toprotrudefromthewall.

5. Positionthe bottomholeofthedoorcontroloverthescrewandslidedownintoplace.

6. Liftthepushbarupandmarkthetop hole.

7. Removethedoor controlfromthewall and drill a5/32 inch(4mm)holeforthetop screw.

8. Positionthe bottomholeofthedoorcontroloverthescrewandslidedownintoplace.Attach thetopscrew.

ram)

DRYWALL

GANG BOX

DRYWALL

Page 22

Installation

STEP 11Wire the door control to the garagedoor opener

HARDWARE

InsulatedStaple

(NotShown)

1. Runthewhiteandred/whitewirefromthedoorcontroltothegaragedooropener.Attachthe wiretothewallandceilingwiththestaple(notapplicableforgang boxorpre-wired installations).Donotpiercethewirewiththe stapleasthismaycauseashortor anopen

circuit.

2. Strip7/16inch(11mm)ofinsulationfromtheendofthewirenearthegaragedooropener.

3. Connectthewireto the redandwhiteterminalsonthegaragedooropener.Ifyourgarageis pre-wiredmakesureyouusethe samewiresthatareconnectedtothedoorcontrol.To insert or releasewiresfromthe terminal,pushinthetabwithscrewdrivertip.

STEP 12Attachthe warning labels

1. Attachtheentrapmentwarninglabel onthewallnear thedoor controlwithtacksorstaples.

2. Attachthemanualrelease/safetyreversetestlabelinavisiblelocationon the insideofthe garagedoor.

Page 23

Installation

STEP 13 Install the ProtectorSystem® HARDWARE

Besurepower isNOTconnectedtothegarage dooropenerBEFOREinstallingthesafetyreversing sensor.

ITo preventSERIOUSINJURYor DEATHfromclosinggaragedoor:

• Correctlyconnectandalign thesafetyreversingsensor.ThisrequiredsafetydeviceMUSTNOTbe

• disabled. nsta the safetyreversng sensorso beams NOHGHERthan6 (15cm)abovegaragefoor.

IMPORTANTINFORMATIONABOUTTHE SAFETYREVERSINGSENSORS

Thesafetyreversingsensorsmustbe connectedandalignedcorrectlybeforethe garagedoor openerwillmoveinthedowndirection.

Thesendingsensor(withan amber LED)transmitsan invisiblelightbeamtothereceivingsensor(witha greenLED).Ifanobstructionbreaksthelightbeamwhilethedooris closing,thedoorwillstopand reversetothefullopenposition,andthegarage dooropenerlightswillflash10times.

NOTE:For energyefficiencythegarage dooropenerwillenters/eepmodewhenthedooris fu//y closed.Thesleepmodeshutsthegaragedooropenerdownunti/activated.Thesleepmodeis sequencedwiththegarage door opener/ightbu/b;asthe/ightbu/bturnsoffthesensorLEOswillturn off andwheneverthegaragedooropenerlightsturn on thesensorLEOswilllight.Thegarage dooropener

willnot go intothesleep modeuntilthegarage dooropenerhascompleted5 cyclesuponpower up.

NOTE: Wheninstallingthesafetyreversingsensorscheck thefollowing:

• Sensorsareinstalledinsidethegarage,one on eithersideofthedoor.

• Sensorsarefacingeachotherwiththelensesalignedandreceivingsensorlensdoesnot receivedirectsunlight.

• Sensorsarenomorethan6 inches(15cm)abovethefloorand thelightbeamis unobstructed.

Invisible Light Beam Protection Area

Safety Reversing Sensor

6" (15 cm) max. above floor

CarriageBolt _ Wing Nut

1/4"-20xl/2" 1/4"-20

The safety reversing sensors can be attached to the door track, the wall, or the floor. The sensors should be no more than 6 inches (15 cm) above the floor. If the door track will not support the sensor bracket a wall installation is recommended. Choose one of the following installations.

DOOR TRACK INSTALLATION

1. Slide the curvedarmsofthesensorbracketaroundthe edgeofthe doortrack.Snapintoplace so thatthesensorbracketisflushagainstthe track.

2. Slide the carriageboltintothe sloton eachsensor.

3. Inserttheboltthroughtheholein thesensorbracketandattachwiththewingnut.Thelenses on bothsensorsshouldpointtowardeachother.Makesurethelensisnotobstructedbythe

sensorbracket.

Carriage Bolt 1/4"-20xl/2"

Page 24

Installation

STEP 13 Install the ProtectorSystem® (continued) FLOOR,NSTALLAT,ON

wALL..STAL T.O.

Ifadditionalclearanceisneededanextensionbracket(notprovided)or woodblockscanbe used,Make sureeachbrackethasthe sameamountofclearancesotheywillaligncorrectly,

1, Positionthe sensorbracketagainstthewallwiththecurved armsfacingthedoor, Makesure

thereisenoughclearanceforthe beamto be unobstructed,Markholes,

2, Drill3/16inchpilotholesforeachsensorbracketandattachthe sensorbracketstothewall

usinglagscrews(notprovided),

3, Slidethe carriagebolt intotheslotoneachsensor,

4. Inserttheboltthroughtheholeinthe sensorbracketand attachwiththewingnut.The lenses onbothsensorsshouldpointtowardeachother,Makesurethelensisnotobstructedbythe sensorbracket,

' _ /Notprov,ded/

°_¢_1 Nomorethan

_! 61nches(15cm)

CarriageBolt

Lens ,_ 1/4"-20xl/2"

Useanextensionbracket(notprovided)orwoodblocktoraisethesensorbracketifneeded,

1, Carefullymeasurethe positionof bothsensorbracketssotheywillbethesamedistancefrom

thewallandunobstructed, 2, Attachthesensorbracketstothefloor usingconcreteanchors(notprovided), 3, Slide the carriageboltintothe sloton eachsensor, 4, Inserttheboltthroughtheholein thesensorbracketandattachwiththewingnut,Thelenses

on bothsensorsshouldpointtowardeachother,Makesurethelensisnotobstructedbythe

sensorbracket,

provided)

Carriage Bolt 1/4"-20xl/2"

Nut

1/4"-20

Page 25

Installation

STEP 14Wire the Safety ReversingSensors

Ifyour garagealreadyhaswiresinstalledforthesafetyreversingsensors,proceedtopage25.

HARDWARE

InsulatedStaple (NotShown)

6#_i_ _ INSTALLATIONWITHOUTPRE-WIRING

1. Runthewirefromboth sensorstothegaragedoor opener.Attachthewiretothewalland ceilingwiththestaples.

2. Strip7/16inch(11mm)of insulationfromeachsetofwires.Separatethewires.Twistthewhite wirestogether.Twistthewhite/blackwirestogether.

3. Insertthewhitewiresintothewhiteterminalonthe garagedooropener. Insertthewhite/black wiresintothe greyterminalonthegaragedooropener.Toinsertorremovethewiresfromthe terminal,pushinthe tabwithascrewdrivertip.

Staple

7/16" (11 mm)

Page 26

Installation

STEP 14Wire the Safety ReversingSensors(continued)

PRE-W,RED,NSTALLAT,ON

Cuttheend of thesafetyreversingsensorwire,makingsurethereisenoughwire to reachthe pre-installedwiresfromthewall. Separatethesafetyreversingsensorwiresandstrip7/16inch(11mm)ofinsulationfromeach end.Ohoosetwoofthepre-installedwiresandstrip7/16inch(! 1mm)ofinsulationfromeach end.Makesurethatyouchoosethesamecolorpre-installedwiresfor eachsensor. Connectthepre-installedwirestothesensorwireswithwirenutsmakingsurethecolors correspondforeachsensor.Forexample,thewhitewirewouldconnecttotheyellowwireand thewhite/blackwirewouldconnecttothe purplewire. Atthe garagedoor opener,strip7/16inch (! 1mm)ofinsulationfromeachend ofthe wires previouslychosenforthesafetyreversingsensors.Twistthelike-coloredwirestogether. Insertthewiresconnectedto the whitesafetysensorwirestothewhiteterminalonthegarage dooropener.Insertthewiresthatareconnectedtothe white/blacksafetysensorwirestothe greyterminalon thegaragedooropener.

Pre-installed Safety reversing wires sensor wires

Not Provided

Safety reversing Pre-installed wires

sensor wires

White Yellow (for example)

White/Black Purple (for example)

Yellow

_r exampe)

Purple

x°armp,e/

To insert or remove the wires from the terminal, push in the tab with a screwdriver tip.

Page 27

Installation

STEP 15 Connectpower

To preventpossibleSERIOUSINJURYorDEATHfromelectrocutionorfire:

• Besurepoweris NOTcennectedto the opener,anddiscennectpowertocircuitBEFORE removingcovertoestablishpermanentwiringconnection.

• Garagedoor installationandwiringMUSTbeincompliancewithALLlocalelectricalandbuilding codes.

• NEVERusean extensioncord,2-wireadapter,orchangepluginanywayto makeitfitoutlet.Be surethe opener isgrounded.

Toavoidinstallationdifficulties,donotactivatethegaragedooropenerat thistime. Toreducethe riskof electricshock,your garagedooropener hasagroundingtypeplugwithathird groundingpin.Thisplugwillonlyfitintoagroundingtypeoutlet.Iftheplugdoesn'tfitintoyouroutlet, contacta qualifiedelectriciantoinstallthe properoutlet.

THEREARETWOOPTIONSFORCONNECTINGPOWER:

TYPICAL WIRING

1. Pluginthegaragedooropenerintoagroundedoutlet.

2. DONOTrungaragedoor openeratthistime.

PERMANENT WIRING

Ifpermanentwiringisrequiredbyyourlocalcode,refertothefollowing procedure.Tomakea permanentconnectionthroughthe7/8inchholeinthetopof themotorunit(accordingto local

code):

1. Removethemotorunitcoverscrewsand setthecoveraside.

2. Removetheattached3-prong cord.

3. Connecttheblack(line)wiretothescrewonthebrassterminal;the white(neutral)wiretothe screwonthesilverterminal;andthegroundwiretothegreengroundscrew.Theopener

must be grounded.

4. Reinstallthecover.

GroundTab

Green Ground Black Screw Wire

Ground- Wire

WhiteWire Black

Wire

Page 28

Installation

STEP 16 Ensurethe safetyreversingsensorsare aligned

Thedoorwillnotcloseifthe sensorshave notbeeninstalledandalignedcorrectly.

Whenthelightbeamisobstructedormisalignedwhilethedoor isclosing,thedoorwillreverseandthe garagedooropenerlightswillflashtentimes.Ifthedooris alreadyopen, itwill notclose.Thesensors canbealignedbylooseningthe wingnuts,aligningthesensors,andtighteningthewingnuts.

Checkto makesurethe LEDs inbothsensorsareglowingsteadily.TheLEDsinbothsensorswillglow steadilyiftheyarealignedand wiredcorrectly.

If the receiving sensor is in direct sunlight,

switch it with sending sensor so it is on the

opposite side of the door.

IFTHEAMBERLEDON THESENDINGSENSORIS NOTGLOWING:

1. Makesurethereispowertothegaragedooropener.

2. Makesurethesensorwire isnot shorted/broken.

3. Makesurethesensor hasbeenwiredcorrectly:whitewirestowhiteterminaland white/black wiresto greyterminal.

IFTHEGREENLEDONTHERECEIVINGSENSORISNOTGLOWING:

1. Makesurethesensorwire isnot shorted/broken.

2. Makesurethesensorsare aligned.

STEP 17 Ensurethe door control iswired correctly

Ifthedoorcontrolhasbeeninstalledandwired correctly,thecommandLEDon the Motion-Detecting

ControlPanel willblink.

Page 29

Introduction

Withoutaproperlyinstalledsafetyreversalsystem,persons(particularlysmallchildren)couldbe SERIOUSLYINJUREDor KILLEDbyaclosinggaragedoor.

• Incorrectadjustmentofgaragedoortravellimitswillinterferewithproperoperationof safety reversalsystem.

• AfterANYadjustmentsaremade,thesafetyreversalsystemMUSTbetested.DoorMUSTreverse

on contactwith1-1/2"(3.8cm)highobject(or2x4 laidflat)onfloor.

One-PieceDoorsOnly

WhensettingtheUP travelforaone-piecedoorensurethatthedoordoesnotslantbackwardswhen fullyopen(UP).Ifthedoor isslantedbackwardsthiswillcauseunnecessarybuckingand/orjerking whenthe doorisopeningor closing.

To preventdamagetovehides,besurefullyopendoorprovidesadequateclearance.

Yourgaragedooropenerisdesignedwithelectroniccontrolstomakesetupandadjustmentseasy.The adjustmentsallowyoutoprogramwherethedoorwillstopintheopen (UP)andclose(DOWN)position. Theelectroniccontrolssensetheamountofforcerequiredto openandclosethedoor. Theforce is adjustedautomaticallywhenyouprogramthetravel. Ifanythinginterfereswiththedoor'supwardtravelitwill stop.Ifanythinginterfereswiththedoor's downwardtravel,itwillreverse.

Programming Buttons

Theprogrammingbuttonsarelocatedontheleftsidepanelof thegaragedooropenerandare used toprogramthetravel.

PROGRAMMINGBUTTONS

AdiustmentButton

DOWNButton

Towatcha shortinstructionalvideoonhowtoprogramthetravelon yournewgarage door openeruseyoursmartphoneto readthe QR Code:

Page 30

STEP 1 Program the Travel

Withoutaproperlyinstalledsafetyreversalsystem,persons(particularlysmallchildren)couldbe SERIOUSLYINJUREDor KILLEDbyaclosinggaragedoor.

• Incorrectadjustmentofgaragedoor travellimitswillinterferewithproperoperationofsafety reversalsystem.

• AfterANYadjustmentsaremade,thesafetyreversalsystemMUSTbetested.DoorMUSTreverse

on contactwith1-1/2"(3.8cm)highobject(or2x4 laidflat)onfloor.

1. Pressand holdtheAdjustmentButtonuntiltheUPButtonbeginsto flashand/orabeepis heard.

2. PressandholdtheUPButtonuntilthedooris inthedesiredUPposition.NOTE: TheUPand

DOWNButtonscanbeusedto movethe door up and downasneeded.

3. Oncethe doorisinthe desiredUP positionpressand releasethe AdjustmentButton.The garagedoor openerlightswillflashtwiceandthe DOWNButtonwillbegintoflash.

4. PressandholdtheDOWNButtonuntilthedooris inthedesiredDOWNposition.NOTE:The

UPandDOWNButtonscanbeusedtomovethedoorupanddownasneeded.

5. Oncethe doorisinthe desiredDOWNpositionpressandreleasethe AdjustmentButton.The garagedoor openerlightswillflashtwiceandthe UPButtonwillbegintoflash.

6. Pressandreleasethe UPButton.WhenthedoortravelstotheprogrammedUPposition,the DOWNButtonwillbegintoflash.

7. Pressandreleasethe DOWNButton.ThedoorwilltraveltotheprogrammedDOWNposition. Programmingiscomplete.

*Ifthegaragedooropenerlightsareflashing5 timesduringthestepsforProgramthe Travel,the programminghastimedout.Ifthegaragedooropenerlightsareflashing10timesduringthestepsfor ProgramtheTravel,thesafetyreversingsensorsaremisalignedorobstructed(refertopage28).When thesensorsare alignedandunobstructed,cyclethedoorthroughacompleteupanddowncycleusing theremotecontrolor theUP and DOWNbuttons.Programmingiscomplete.Ifyouare unabletooperate thedoor upand down,repeatthestepsfor Programmingthe Travel.

PROGRAMMING BUTTONS

UP Button

_ djustment ButtonDOWN Button

Page 31

STEP 2 Test the SafetyReversalSystem

STEP 3 Test the ProtectorSystem®

Withoutaproperlyinstalledsafetyreversalsystem,persons(particularlysmallchildren)couldbe SERIOUSLYINJUREDor KILLEDbyaclosinggaragedoor.

• SafetyreversalsystemMUSTbetestedeverymonth.

• AfterANYadjustmentsaremade,thesafetyreversalsystemMUSTbetested.DoorMUSTreverse on contactwith1-1/2"(3.8cm)highobject(or2x4 laidflat)onthefloor.

1. Withthedoorfullyopen,placea 1-1/2inch(3.8cm)board(ora 2x4laidflat) onthe floor, centeredunderthegaragedoor.

2. Presstheremotecontrolpushbuttontoclosethedoor. ThedoorMUSTreversewhenitmakes contactwiththe board.

Ifthedoorstopsand doesnotreverseontheobstruction,thedowntravelneedsto be increased(referto AdjustmentStep1).Repeatthetest.Whenthedoor reversesuponcontactwiththe1-1/2inchboard, removetheboardandopen/clocethe door3or4 timestotesttheadjustment.Ifthegaragedooropener continuestofailthesafetyreversaltest,callatraineddoor systemstechnician.

Withoutaproperlyinstalledsafetyreversingsensor,persons(particularlysmallchildren)couldbe SERIOUSLYINJUREDorKILLEDbyaclosinggarage door.

1. Openthedoor.Placethegarage door openercartoninthe pathofthe door.

2. Presstheremotecontrolpushbuttontoclosethedoor.The doorwillnot movemorethanan inch(2.5cm),andthe garagedooropener lightswill flash10 times.

Thegaragedooropenerwillnotclosefroma remotecontroliftheLED ineithersafetyreversingsensor isoff(alertingyouto the factthatthesensor ismisalignedor obstructed).Ifthegaragedooropener closesthe doorwhenthesafetyreversingsensorisobstructed(andthesensorsare nomorethan6 inches[15cm]abovethefloor),callforatraineddoorsystemstechnician.

Page 32

IMPORTANTSAFETYINSTRUCTIONS

ToreducetheriskofSEVEREINJURYorDEATH:

1. READANDFOLLOWALLWARNINGSAND INSTRUCTIONS.

2. ALWAYSkeepremotecontrolsoutof reachofchildren.NEVERpermitchildrentooperateor playwithgaragedoorcontrolpushbuttonsor remotecontrols.

3. ONLYactivategaragedoorwhenitcanbeseendearly,it isproperlyadjusted,andthere are noobstructionstodoor travel.

4. ALWAYSkeepgaragedoor insightandawayfrompeopleand objectsuntilcompletely closed. NOONESHOULDCROSSTHEPATHOFTHEMOVINGDOOR.

5. NOONESHOULDGOUNDERA STOPPED,PARTIALLYOPENEDDOOR.

6. Ifpossible,useemergencyreleasehandletodisengagetrolleyONLYwhengaragedoor is CLOSED.Usecautionwhen usingthereleasewiththedoor opener.Weakorbrokensprings or unbalanceddoorcouldresultinan opendoorfallingrapidlyand/orunexpectedlyand increasingtheriskof SEVEREINJURYorDEATH.

7. NEVERuseemergencyreleasehandleunlessgaragedoorwayisclearofpersonsand obstructions.

8. NEVERusehandle to pullgaragedooropen orclosed.Ifropeknotbecomesuntied,you couldfall.

9. AfterANYadjustmentsare made,thesafetyreversalsystemMUSTbetested.

10. SafetyreversalsystemMUSTbetestedeverymonth.GaragedoorMUSTreverseon contactwith1-1/2"(3.8cm)highobject(ora 2x4laidflat)onthefloor.Failuretoadjustthe garagedooropenerproperlyincreasestheriskofSEVEREINJURYor DEATH.

11. ALWAYSKEEPGARAGEDOORPROPERLYBALANCED(seepage2).Animproperly balanceddoormayNOTreversewhenrequiredand couldresultinSEVEREINJURYor

DEATH.

12. ALLrepairstocables,springassembliesand other hardware,ALL ofwhichareunder EXTREMEtension,MUSTbe madebyatraineddoor systemstechnician.

13. ALWAYSdisconnectelectricpowertogaragedooropener BEFOREmakingANY repairsorremovingcovers.

14. Thisoperatorsystemisequippedwithanunattendedoperationfeature.Thedoorcould moveunexpectedly.NOONESHOULDCROSSTHEPATHOFTHEMOVINGDOOR.

15. DONOTenabletheTimer-to-Closefunctionalityifoperatingeitherone-pieceor swinginggaragedoors.Tobeenabled ONLYwhenoperatingasectionaldoor.

16. SAVETHESEINSTRUCTIONS.

Page 33

Features

Yourgaragedooropenerisequippedwithfeaturesto provideyouwithgreatercontroloveryourgarage dooroperation,

Alert2Close

TheAlert2Closefeatureprovidesavisualandanaudiblealertthat an unattendeddooris closing,

TIMER-TO-CLOSE (TTC)

TheTimer-to-Closefeatureautomaticallyclosesthedooraftera specifiedtimeperiodthatcanbe adjustedusingthedoorcontrol.DONOTenablerrc if operatinga one-piecedoor.TFC is to beused ONLYwithsectionaldoors.Factorydefaultissettooff.Thegaragedooropenerwillbeepandthe lights willflash beforeclosingthedoor.TheTTCfeaturewilldeactivateifthegaragedoor encountersan obstructiontwice;or thesafetyreversingsensorsareincorrectlyinstalled.Thegaragedoorwillreverse openand WILLNOTcloseuntiltheobstructionsare clearor thesafetyreversingsensorsarecorrectly installed.Whentheobstructionhasbeenclearedorthesafetyreversingsensorshavebeenaligned,the doorwillclosewhenthegaragedooropenerisactivated.TTCWILLNOTwork ifthegaragedooropener isoperatingbybatterypowerorifthesafetyreversingsensorsaremisaligned.ThisfeatureisNOT intendedtobetheprimarymethodofclosingthedoor.Akeyless entry shouldbeinstalled inthe event of anaccidental lock outwhen using this feature.

MyQ® MyQ®technologyusesa900MHzsignalto providetwo-waycommunicationbetweenthegaragedoor

openerand MyQ®enabled accessories.Yourgaragedoor openeriscompatiblewithupto 8MyQ® accessories.

REMOTE CONTROLS AND DOOR CONTROLS (MyQ®) Yourgaragedooropenerhasalreadybeenprogrammedat the factorytooperatewithyourremote

control,whichchangeswitheachuse,randomlyaccessingover 100 billionnew codes.Compatiblewith MyQ®enabledaccessories,seepage 39.

NOTE: OlderChamberlainremotecontrols,doorcontrols,and thirdpadyproductsarenotcompatible.

THE PROTECTOR SYSTEM ® (SAFETY REVERSING SENSORS) Whenproperlyconnectedandaligned,thesafetyreversingsensorswilldetectan obstructioninthepath

oftheinfraredbeam.Ifanobstructionbreakstheinfraredbeamwhilethedooris closing,thedoorwill stopandreversetofull openposition,andtheopenerlightswillflash10times.Ifthe doorisfullyopen, andthe safetyreversingsensorsarenot installed,oraremisaligned,thedoorwillnotclosefroma remotecontrol.However,youcanclosethedoorifyouholdthe buttononthedoorcontrolor keyless entryuntilthe door isfullyclosed.Thesafetyreversingsensorsdonoteffecttheopeningcycle. ENERGY CONSERVATION

Forenergyefficiencythegaragedooropenerwill entersleepmodewhenthedoorisfullyclosed.The sleepmodeshutsthegaragedooropenerdownuntilactivated.Thesleep modeissequencedwiththe garagedooropenerlightbulb;asthe lightbulbturnsoffthe sensorLEDswillturnoffandwheneverthe garagedooropenerlightsturnon thesensorLEDswilllight.Thegaragedooropenerwillnotgointothe sleepmodeuntilthegaragedooropenerhascompleted5 cyclesuponpowerup.

LIGHTS Thegaragedooropenerlightbulbswillturnon whentheopenerisinitiallyplugged in;powerisrestored

afterinterruption,or whenthegarage door opener isactivated.Thelightswilltum offautomaticallyafter 4-1/2minutes.AnincandescentA19 lightbulb (100wattmaximum)orformaximumenergyefficiencya 26W(100Wequivalent)compactfluorescentlight(CFL)bulbmaybe used.NOTE:Dorictus® halogen,

shortneck,or speda/ty/ightbu/bsasthesemayoverheattheend pane/or/ightsocket.Dorictus®LED bulbsas theymayreducetherangeorpefformanceofyourremotecontrols.

Light Feature Thegaragedooropenerisequippedwithan addedfeature;the lightswillturnonwhensomeoneenters throughtheopen garagedoorandthesafetyreversingsensorinfraredbeamis broken,Foradded controloverthe lightbulbsonyourgaragedooropener,seepage33.

Page 34

Using your GarageDoorOpener

Thegaragedooropenercanbe activatedthrougha wall-mounteddoorcontrol,remotecontrol,wireless

keylessentryor MyQ® accessory. Whenthedoorisclosedand thegarage door opener isactivatedthedoor will open.Ifthedoor senses

anobstructionorisinterruptedwhileopeningthedoorwillstop.Whenthe door isinanypositionother

thanclosedandthegarage dooropenerisactivatedthe doorwillclose.Ifthegaragedooropener

sensesanobstructionwhileclosing,the door willreverse.Ifthe obstructioninterruptsthesensorbeam

thegaragedooropenerlightswillblink10times.However,youcanclosethe doorifyouholdthebutton

onthe doorcontrolor keylessentryuntilthedoorisfullyclosed.Thesafetyreversingsensorsdonot affecttheopening cycle.

Thesafetyreversingsensormustbe connectedand alignedcorrectlybeforethe garagedooropener will

moveinthe downdirection.

Using the Motion DetectingControlPanel

Tosynchronizethedoorcontrolto the garagedooropener,pressthepushbaruntilthegaragedoor

openeractivates(itmaytakeup to3presses).Testthedoorcontrolbypressingthepushbar,eachpress ofthepushbar willactivatethe garage dooropener.

LOCKButton/

Motion Sensor Switch

ON(R-C) Push Bar _ HOLDOPEN

1, 5, and _ Ii J- Button(TTC) 10 Minute _1_1

OFF(R-C) TTCLED LIGHT Button

Motion Sensor

PUSH BAR

Pressthe pushbartoopenor closethe door. LIGHTS LightButton

Pressthe LIGHTbuttontoturnthe garagedooropenerlightsonor off.Whenthe lightsareturnedon theywillstayon untilthe LIGHTbuttonispressedagain,or untilthegaragedooropenerisactivated. Oncethe garage dooropenerisactivatedthe lightswillturnoffafterthespecifiedperiodoftime(the factorysettingis4-1/2minutes).TheLIGHTbuttonwill notcontrolthelightswhenthedooris in motion.

To changethe amount of time thegaragedooropenerlightswill stay on:

Pressand holdtheLOCKbutton(approximately10seconds)untilthegaragedooropenerlightsflash. Thetimeintervalisindicatedbythe numbertimesthegaragedooropenerflashes:

• 1flashis1-1/2 minutes

• 2 flashesis2-1/2minutes

• 3 flashesis3-1/2minutes

• 4 flashesis4-1/2minutes

To cyclethroughthetimeintervalsrepeatthestepabove.

LightFeature Thelightswillturn on whensomeoneentersthroughtheopengaragedoorandthesafetyreversing

sensorinfraredbeamis broken.

• Deactivate:PressandholdtheLIGHTbutton(approximately10seconds)untilthegarage door openerlightsturnon,thenoffagain.

• Activate: Startwiththegaragedooropenerlightson.Pressandholdthe LIGHTbutton

(approximately10 seconds)untilthe garagedoor opener lightstumoff,thenonagain.

IfthecommandLEDiscontinuouslyblinking,the LOCKfeatureneedsto be deactivated.

Page 35

Usingthe ControlPanel (continued)

LOCK

The LOCKfeatureisdesignedtopreventactivationofthegaragedooropenerfromremotecontrols

whilestillallowingactivationfromthe doorcontroland keylessentry,Thisfeatureisusefulforadded peaceofmindwhenthehomeisempty(i,e,vacation),

• Activate: PressandholdtheLOCKbuttonfor2seconds,ThecommandLEDwillflashas longasthelockfeatureisactivatedand yourhandheldremotecontrolwillnot operateyour

dooratthistime,

• Deactivate:Pressandholdthe LOCKbuttonagainfor2seconds,ThecommandLEDwill

stopflashingandnormaloperationwill resume, TIMER-TO-CLOSE IX) NOTenableTTCif operatingaone-piece door.TheTTCcanbeturnedonoroff andthetime

intervalcanbeadjustedto1,5,and10minuteintervals,Once theTTChasbeensetandthedooris open,theselectedcloseintervalwillblinkandbeginto countdownto closethedoor,

• Activate: Pressand holdtheONbuttonuntiloneofthe TTCLEDslightup,ThenpresstheON buttonagainto cyclethroughthetimeintervaloptions(thecorrespondingTTCLEDwilllight

foreachtimeinterval),Thegarage dooropenerlightbulbs willblinkasconfirmation,

• Deactivate:PressandholdtheOFFbuttonuntilall TTCLEDstumoffandabeepisheard

fromthemotorunit,

• Temporarily holddooropen(suspendTTC):Pressand releasetheHOLDOPENbutton, Pressthe HOLDOPENbuttonagainto resumenormalTTCoperation,

PROGRAM

Anycompatibleremotecontrols,wirelesskeylessentry,orMyQ® accessoriescanbe programmedtothe garagedooropenerbypressingthe Learn button,

CommandLED

MotionSensor

•Switch

....... _ON (TTC) PushBar

HOLDOPEN

LEARNButton-- _ "_ _ 1,5, and _ IllJ.-Button(TTC)

O _ OFF(TTC) 10Minute I _1

LOCKButton/ ooo

TTCLED I _t..-- LIGHTButton

MotionSensor

RemoteControl

Yourremotecontrolhas beenprogrammedat thefactory to operatewithyourgaragedooropener.

OlderChamberlainremotecontrolsare NOTcompatible,seepage 39 forcompatibleaccessories, Programmingcanbedonethroughthe doorcontrolor thelearnbuttonthegaragedooropener,To programadditionalaccessoriesrefertotheinstructionsprovidedwiththeaccessoryor visit www,chamberlain,com,Ifyourvehicleisequippedwitha Homelinke, youmayrequire an external adapterdependingonthemake,model,andyearofyourvehicle,Visitwww,homelink,comforadditional

information, TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROUKEYLESS ENTRY PIN

USING THE MOTION-DETECTING CONTROL PANEL

1, Pressthe LEARNbuttononthedoorcontroltoenterProgrammingMode,

2, PresstheLEARNbuttonagain,the LEDwillflashonce,

3. RemoteControl: Pressthe buttonontheremotecontrolthatyouwishtooperateyourgaragedoor, Keyless Entry:

Entera4-digitpersonalidentificationnumber(PIN)ofyourchoiceonthekeylessentry keypad,ThenpresstheENTERbutton,

Thegaragedooropenerlightswillflash(ortwoclickswill be heard)whenthe codehasbeen programmed,Repeatthestepsforprogrammingadditionalremotecontrolsor keylessentrydevices,

1 The command LED _

will flash once.

2 The command LEDwill

flash once again.

? ? ?

Page 36

RemoteControl(continued)

PROGRAM A REMOTE CONTROL USING THE LEARN BUTTON

1, Locatethe LearnButton, 2, Pressandimmediatelyreleasethe Learn button,TheLearnLEDwillglowsteadyfor30

seconds,Within30seconds,,,

3, Pressandholdthebuttonontheremotecontrolthatyouwishtouse,

Releasethebuttonwhenthe garagedoor opener lightsblinkortwoclicksareheard, Whenreplacingthe lightlenscover,ensuretheantennawiresarehangingstraightdown,

To Erase the Memory

ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES

1, PressandholdthelearnbuttonongaragedooropeneruntilthelearnLEDgoesout

(approximately6 seconds),All remotecontrolandkeylessentrycodesarenowerased, Reprogramanyaccessoryyouwishtouse,

ERASE ALL DEVICES (Including MyQ®enabled accessories)

1, PressandholdthelearnbuttonongaragedooropeneruntilthelearnLEDgoesout

(approximately6 seconds),

2, Immediatelypressandholdthe learnbuttonagainuntilthelearn LEDgoesout,Allcodesare

nowerased, Reprogramanyaccessoryyouwishtouse,

To Openthe Door Manually

TopreventpossibleSERIOUSINJURYor DEATHfromafallinggaragedoor:

• Ifpossible,useemergencyreleasehandletodisengagetrolleyONLYwhengaragedooris CLOSED,Weakorbrokenspringsorunbalanceddoorcould resultinanopendoorfalling rapidlyand/orunexpectedly,

• NEVERuseemergencyreleasehandleunlessgaragedoorwayisclearofpersonsand obstructions,

• NEVERusehandletopulldoor open orclosed,Ifropeknotbecomesuntied,youcouldfall.

DISCONNECTTHETROLLEY

1, Thedoorshouldbefullyclosedif possible,

2, Pulldownon the emergencyreleasehandlesothetrolleyreleasearmsnapstothevertical

position,Thedoorcan nowbe raised and loweredas oftenasnecessary,

RECONNECTTHETROLLEY

1, Pulltheemergencyreleasehandletowardthegaragedooropenersothetrolley releasearm

snapsto thehorizontalposition, ThetrolleywillreconnectonthenextUPorDOWNoperation,eithermanuallyorby usingthe doorcontrolor remotecontrol,

Page 37

Maintenance

MaintenanceSchedule

EVERYMONTH

• Manuallyoperatedoor.If it is unbalancedor binding,callatraineddoorsystemstechnician.

• Checktobe suredoor opensand closesfully.Adjustifnecessary,seepage28.

• Testthe safety reversal system. Adjust if necessary, see page 28.

EVERY YEAR

• Oildoorrollers,bearingsandhinges.Thegaragedooropener doesnotrequireadditional

lubrication. Do not grease the door tracks.

The RemoteControl Battery

TopreventpossibleSERIOUSINJURYor DEATH:

• NEVERallow smallchildrennearbatteries.

• Ifbatteryisswallowed,immediatelynotifydoctor. Toreduceriskoffire, explosionorchemicalburn:

• ReplaceONLYwith3V2032coinbatteries.

• DONOTrecharge,disassemble,heatabove212°F(100°C)or incinerate.

The3V2032lithiumbatteryshouldproducepowerforup to 5 years.If thebatteryislow,theremotecontrol'sLEDwillnotflashwhenthe buttonis pressed. Toreplacebattery,pryopenthecasefirstinthe middle(1),thenat eachside(2 and 3)withthevisorclip. Replacethebatterieswithonly3V2032coincellbatteries.Insert batterypositivesideup.Disposeofoldbatteriesproperly.

NOTICE:Tocornp]ywith FCCand/orlndustryCanada (IC)rules,adjustmentorrnod_f_ationsofthistransceiverare prohib_ted.THERE ARENO USER SERVICEABLEPARTS.Any changes orrnodificationsnotexpresslyapproved by the partyresponsble for compliance

couldvo)dthe useCsauthorityto operate the equ)prnent. Thisdevice compliesw)thPart15 of the FCCru(esand ICRSS-210. Operationissubjectto the fo((owingtwo conditions: (1)this device maynotoause harmfulinterference, and (2)th)sdev)cemustacceptanyinterference received,including)nterferencethat rnaycauce undesired operation

ThsOhssBdgita apparatuscornp eswithCanadian CES-003. AVIS:Lesr_glesde h FCCet/ou d'(ndustrie Canada (IC)interdisenttout ajustementou toute modificationde ce r_cepteur. IL

N'EXlSTEAUCUN EPIECESUSCEPTIBLED'ETREENTRETENUEPARL'UT)L(SATEUR.Tout changement ouroute modif#atiomeon express_mentapprouv6 par#. part(eresponsablede h conformit6peut avoirpour resultatd'an nuJetlautor_ de I'utU(sateurdefaire

fonct)onnerr6qu)pement. Cet appare)lestconforrneaux dispos_t)onsde h part)e15du r_g(ernentde (aFCCet de rnorme ICRSS-210 Son ut)lisat)onest

assujett)eauxdeux condito)ns suivantes: (1)ced)spos_flfne peut causerdesinterf6rences nu[s)bles,et(2) ced_pos_ifdo_accepter route)nterference recue, ycornpdsuneinterference pouvant causerun fonct)onnement non souhait6. Cetappare nurnerique de acasseBestcon orrnea a nomle NMB-003 duCanada

Page 38

DiagnosticChart

Yourgaragedooropenerisprogrammedwithself-diagnosticcapabilities.The UPand DOWNarrowsonthe garagedooropener flashthediagnosticcodes.

DIAGNOSTICCODE SYMPTOM SOLUTION

UpArrow DownArrow Flash(es) Flash(es)

1 1 Thegaragedoor openerwill notcloseandthelight Safetysensorsarenotinstalled,connected,or wiresmaybe cut.Inspectsensorwiresfora

bulbsflash, disconnectedorcutwire.

1 2 Thegaragedoor openerwill notcloseandthelight Thereisa shortorreversedwireforthesafetysensors.Inspectsafetysensorwireatallstapleand

bulbsflash, connectionpoints,replacewireor correctasneeded

1 3 Thedoor controlwill notfunction. Thewiresforthe doorcontrolareshortedorthedoorcontrolisfaulty.Inspectsafetysensorwireatall

staplepointsandconnectionpointsand replacewire orcorrectasneeded.

1 4 Thegaragedoor openerwill notcloseandthelight Safetysensorsaremisalignedorweremomentarilyobstructed.Realignbothsensorsto ensureboth

bulbsflash. LEDsaresteadyand notflickering.Makesurenothingis hangingor mountedonthedoorthatwould

interruptthesensor'spathwhiledosing.

1 5 Doormoves6-8"stopsor reverses. Manuallyopenand closethedoor.Checkforbindingor obstructions,suchasa brokenspringordoor

lock,correctas needed.Checkwiringconnectionsattravelmoduleand atthelogicboard.Replace travelmoduleifnecessary.

Nomovement,onlya singledick. Manuallyopenand closethedoor.Checkforbindingor obstructions,suchasa brokenspringordoor

lock,correctas needed.Replacelogicboardifnecessary.

Openerhurnsfor 1-2secondsnomovement. Manuallyopenandclosethedoor.Checkforbindingor obstructions,suchasa brokenspringordoor

lock,correctas needed.Replacemotorifnecessary.

1 6 Doorcoastsafterithascometoacompletestop. Programtraveltocoastingpositionor havedoorbalancedbyatraineddoorsystemstechnidan. 2 1-5 Nomovement,orsound. Replacelogicboard. 3 2 Unabletosetthetravelor retainposition. Checktravelmoduleforproperassembly,replaceif necessary.

Page 39

DIAGNOSTICCODE SYMPTOM SOLUTION

UpArrow DownArrow Flash(es) Flash(es)

4 1-4 Doorismovingstopsor reverses. Manuallyopenand closethedoor.Checkforbindingor obstructions,suchas abrokenspringor doorlock,

correctasneeded.Ifthedoorisbindingorstickingcontactatraineddoorsystemstechnician.If door isnot bindingor stickingattempttoreprogramtravel(refertopage28).

4 5 Openerrunsapproximately6-8",stopsandreverses. C_mmunicati_nerr_rt_trave_m_du_e_Checktra_e_m_du_econnecti_ns_rep_acetra_e_m_du_eif

necessary.

4 6 Thegarage door openerwill notcloseandthe light Safetysensorsare misalignedorweremomentarilyobstructed.RealignbothsensorstoensurebothLEDs

bulbsflash, aresteadyandnotflickering.Makesurenothingis hangingor mountedonthedoorthatwouldinterrupt

thesensor'spathwhileclosing.

Thegaragedooropenercanbeep for several reasons:

• GaragedooropenerhasbeenactivatedthroughadeviceorfeaturesuchasTimer-to- Closeorgaragedoormonitor,seepage32.

My remote controlwillnotactivatethegaragedoor:

• Verifythe lockfeatureisnot activatedonthedoorcontrol.

• Reprogramthe remotecontrol.

• Iftheremotecontrolwillstillnot activatethedoorcheckthe diagnosticcodestoensure thegaragedooropenerisworkingproperly.

My doorwillnotcloseandthelightbulbsblink onmymotor unit: Thesafetyreversingsensormustbeconnectedand alignedcorrectlybeforethegarage dooropenerwillmoveinthe downdirection.

• Verifythe safetysensorsareproperlyinstalled,alignedandfreeofanyobstructions.

Mygaragedooropenerlight(s)willnotturnoffwhenthedoorisopen: Thegaragedoor openerisequippedwitha featurethatturnsthelight on whenthe safetyreversingsensors havebeenobstructedorwhen the motionsensoronthe door controldetectsmovementin thegarage.These featurescanbe disabledusingthe door control,seepage33. My neighbor'sremote controlopensmy garagedoor: Erasethememoryfromyourgaragedooropenerandreprogramtheremotecontrol(s). TheLEDsonthedoorcontrolblink:

Ifyouhavea SmartControlPanelinstalledandtheFIC issettoa customtime,presstheONbuttononthe PremiumMotion-DetectingControlPaneltosetthetimeproperly. My vehicle's Homelink_ is not programmingto my garagedoor opener: Dependingonthemake,model,and yearofyourvehicleanexternaladaptermaybe required.Visit

www.homelink.comforadditionalinformation.

Page 40

Accessories

7702CB OutsideQuickRelease: 41A5281 ExtensionBrackets:

Requiredfora garage withNO (Optional)Forsafetyreversing

_ accessdoor, _ sensorinstallationonto thewallor

floor,

88080B 8 Foot(2.4m) RailExtension: PILCEV

Toallowan 8 foot(2,4m)doorto

_ openfully,

8810CB 10Foot(3m) RailExtension: CLLP1

Toallowa 10foot(3 m)doorto

openfully,

MyQ®RemoteLightControl: Controlhomelightingandgarage

doorswithoneremote,For usewith plug-inlamps,Synchronizetowork withMyQ®compatiblegaragedoor openersandremotecontrols,

LaserParkingAssistant:

Park intherightspoteverytime!A laserbeamisactivatedbyyour garagedooropenerandprojected ontothedashboardofyour vehicle toguideperfectparking,

CLSS1

AGDMEV

BIK01

SystemSurgeProtector: 953EV RemoteControl:

TheGarageDoorOpener WorkswithALL Chamberlainopenersfrom SurgeProtectorisdesignedto _ 1993-present,MyQ®compatible,Includes

protectChamberlaingarage _ visorclip,

dooropenersagainstdamage fromlightningandpower surges,Easytoinstall,

Garage Doorand Gate 956EV

Monitor:

Monitoropen/closedstatusfor

upto4MyQ®compatible garagedooropenersand closethemfromanywherein thehome,

KeychainRemoteControl: WorkswithALLChamberlainopenersfrom

1993-present,MyQ®compatible,Withkey

ring.

InstallationUpgradeKit: 940EV TheInstallationUpgradeKit

includesallcomponents

neededtohanggaragedoor openersupto24"(61cm)from theceiling,

WirelessKeypad: For useoutsideofthe hometoenable accesstothegarage usinga4-digitPIN. WorkswithALLChamberlainopenersfrom

1993-present.MyQ®compatible.

Page 41

Contactinformation

For installation and service information call:

1-800-528-9131

Before calling, please havethe model number of the garage

door opener. If you are calling about a Troubleshooting issue,

it is recommended thatyou have access to your garage door

openerwhile calling. If you are ordering a repair part please

havethe following information: part number, part name, and

model number.

Addressrepairpartsordersto:

TheChamberlainGroup,Inc.

6050S. CountryClubRoad

Tucson,AZ85706

CHAMBERLAIN® FiVEYEAR LiMiTEDWARRANTY

LIFETIME MOTORAND BELT LIMITED WARRANTY

The Chamberlain Group, Inc.® ("Seller") warrants to the first retail purchaser of this product, for the

residence inwhich this product is originally installed, that it is free from defects in materials and/ or workmanship for a period of five years from the date of purchase, except that the motor and belt are warranted to be free from defects in materials and/or workmanship for the lifetime of the product while you own your residence. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, and maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety.

If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800- 528-9131, toll free, before dismantling this product. You will be advised of disassembly and shipping instructions when you call. Then send the product or component, pre-paid and insured, as directed to our service center for warranty repair. Pleaseinclude a brief description of the problem and a dated proof- of-purchase receipt with any product returned for warranty repair.

Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective andcovered by this limited warranty, will be repaired or replaced (at Seller's sole option) at no cost to you and returned pre-paid. Defective parts will be repaired or replaced with new or factory

rebuilt parts at Seller's sole option. [You are responsible for any costs incurred in removing and/or

reinstalling the product or any component .] ALL iMPLiED WARRANTIES FOR THE PRODUCT, INCLUDING BUTNOT LIMITED TOANY iMPLIED WARRANTIESOF MERCHANTABiLiTY AND FITNESSFORA PARTICULARPURPOSE, ARE LIMITED iN DURATIONTOTHEAPPLICABLELiMiTED WARRANTYPERIODSET FORTHABOVEFORTHE RELATEDCOMPONENT(S), AND NO iMPLIED WARRANTIES WiLL EXIST ORAPPLYAFTERSUCH PERIOD. Some States do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. THIS LIMITED WARRANTY DOESNOT COVERNON-DEFECT

DAMAGE, DAMAGE CAUSED BY iMPROPER INSTALLATION,OPERATION OR CARE (iNCLUDiNG, BUT NOT LIMITEDTO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THiSPRODUCT), LABOR CHARGES FOR REINSTALLINGA REPAIRED OR REPLACED UNIT,REPLACEMENT OF CONSUMABLE

ITEMS (E.G., BATTERIESIN REMOTECONTROLTRANSMITTERS AND LIGHT BULBS), OR UNITS INSTALLED FOR NON-RESIDENTIAL USE. THiS LiMiTED WARRANTY DOES NOT COVERANY

PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITEDTO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES.THISLIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLEFOR CONSEQUENTIAL, INCIDENTALOR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE, OR INABILITYTO USE, THIS PRODUCT. INNO EVENT SHALL SELLER'S LIABILITYFOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITYEXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON ISAUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITYINCONNECTION

WITH THE SALEOFTHIS PRODUCT. Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal

rights, and you may also have other rights, which vary from state to state.

Page 42

RepairParts

RailAssemNyParts

1 Belt 41A5250

2 Pulley 144C54 3 MasterLink 4A1008 4 Rail 41A5665

5 TrolleyAssembly 4105141-1 6 "U" Bracket 12D598-1

NotShown

Wear Pads 183A163

Hardware Bag 041A7920-2

Owner's Manual 114A4309

Accessories

1 Motion-Detecting 41A7327-1

ControlPanel

2 RemoteControl 953ESTD

InstallationParts

1 Curved Door Arm 178B35 2 Door Bracketwith Clevis 41A5047-1

Pin and Fastener

3 Emergency Release 41A2828

Ropeand Handle

4 HeaderBracketwith 41A5047-2

Clevis Pin and Fastener

5 Remote Control 29B137

Visor Clip 6 Safety Sensor Bracket 41A5266-1 7 Safety Sensor Kit 41A5034

Receivingand sending

sensors with wire 8 Straight Door Arm 178B34 9 White and Red/White 41B4494-1

Wire

10 3V2030 Lithium Battery 10A20 11 Hanging Brackets 12B776

Page 43

RepairParts

GarageDoorOpenerParts-WD832KEV

Belt CapRetainer 41A4371 2 Gearand Sprocket 41A4885-5 3 End Panel with Light Socket 41A7760 4 Light Socket 41C279 5 Light Lens 41D7570 6 Capacitor 39B532

Capacitor Bracket 12A373 8 Travel Module 41D7742-7 9 Cover 41A7620-8

10 ReceiverLogic Board 45ACT

I End Panelfor Receiver Logic Board 41D7638

with Light Socket

2 Motor with Travel Module 41A7442 13 Line Cord 41B4245 14 Terminal Block 41A3150

NotShown

Wire Harness Kit 41A7948

Page 44

RepairParts

GarageDoorOpenerParts- HD620EV

3 5

7 14 11

Belt CapRetainer 41A4371

2 Gearand Sprocket 41A4885-5 3 Drive and Worm Gear 41A2817

4 Line Cord 41B4245 5 End Panel with Light Socket 41A7760 6 Light Socket 41C279

Light Lens 41D7572

8 Capacitor 30B652 9 Terminal Block 41A3150

10 Motor and Travel Module 41A7766

I Travel Module 41D7742-5

2 Cover 41A7620-4 13 ReceiverLogic Board 45ACT 14 EndPanelfor Receiver Logic Board 41D7638

with Light Socket

NotShown

Wire Harness Kit 41A7950

114A4309E All RightsReserved