Page 1
CARTON INVENTORY
®
TO
PRESS
R ING
TO
PRESS
R ING
TO
PRESS
R ING
WIRELESS GATEBELL KEYPAD
MODEL 920GA
TABLETOP MOUNTING
Keypad
Remote Control
Power Adapter
Screws (4)
Receiver
1
Insert remote control and power
adapter into receiver. Plug into outlet.
TO
PRESS
R ING
LEARN
LEARN
LEARN
LEARN
PRESS
RING
TO
3
2
1
4
5
Top Mounting Hole
LEARN
LEARN
Bottom
Mounting
Hole
Battery Cover
Battery
Remove battery cover and battery.
Determine location for keypad. Mark
the bottom mounting hole.
Program remote control to the gate
operator radio receiver. Refer to your
gate operator manual for programming
instructions.
Remove foam spacer on underside of
keypad cover. Check range before installing.
Using two people, hold the keypad and
receiver in the desired locations. Make sure
the keypad rings the gatebell when pressed.
If no chime is heard, repeat test using a new
location for the receiver.
NOTE: For optimal range performance, mount the receiver to an external wall that is close to the gate operator. DO NOT MOUNT TO METAL.
For the top mounting screw, mark 4
1/4" (10.8 cm) up the centerline from
the bottom of the keypad. Drill 1/8"
pilot holes for top and bottom screws.
See keypad mounting reference.
Secure keypad with bottom screw, using
care to avoid cracking plastic housing.
Reinstall battery and slide battery cover
up and snap it into place. Close cover.
Install top mounting screw, allowing
1/8" (3.2 mm) to protrude above surface.
Position keypad on screw head and adjust
for snug fit.
KEYPAD MOUNTING
(For reference only)
4 1/4"
(10.8 cm)
Drywall Anchors (2)
INSTALLATION • MOUNT KEYPAD
Lift
INSTALLATION • MOUNT RECEIVER
6
Page 2
Top Cover
9V Battery
Bottom Mounting Hole
Battery Cover
© 2007, The Chamberlain Group, Inc.
114A3448B All Rights Reserved
The battery should produce power for at least one year.
Replace when the keypad illumination becomes dim or it
doesn’t stay on after a keystroke.
Dispose of old battery properly.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
KEYPAD TO INDOOR RECEIVER
CAUTION: Pressing the learn button for more than 6 seconds will clear all the learned keypads.
The keypad can also be programmed to the gate operator using a 4-digit PIN entry code. Refer to your gate operator manual.
LEARN
LEARNLEARN
1
Push “Press to Ring” on the
keypad cover.
Push “Press to Ring” on the
keypad cover within 30 seconds.
Repeat operational test to verify.
Press and release the learn button
on the back of the indoor receiver.
The gatebell will ring.
Press remote control button to open
the gate.
PRESS
R I N G
T O
2
PRESS
R I N G
T O
1
2
3
NOTE: Two people will be needed to properly test the gate doorbell.
Learn Button
PROGRAMMING
OPERATIONAL TEST
THE KEYPAD BATTERY
WALL MOUNTING
Plug power adapter into receiver.
Plug into outlet.
LEARNLEARN
LEARN
1
2
LEARN
LEARN
LEARN
LEARN
LEARN
LEARN
5
4
Screw antenna into receiver. Determine
location for indoor receiver.
Mounting Holes
Insert remote control into receiver.
LEARN
6
Mark and drill pilot holes using 1/4"
drill bit.
Insert drywall anchors.
Position receiver on screw heads.
Drywall
Anchors
Wall
3
Wall
Screw
Install mounting screws, allowing
1/8" (3.2 mm) to protrude above
surface.
INSTALLATION • MOUNT RECEIVER
FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-9131
2 1/8" (5.4 cm)
STOP
The included keypad is learned
to the receiver at the factory.
Follow the next steps to learn
replacement or additional
keypads only.
Loading...