Challenger SL01, SL01B, SL02B, SL03, SL03B Instruction Manual
...
22
22
2 PRODUCT DESCRIPTION
Item
Item
Item
Quantity
Quantity
Quantity
Pattern
Pattern
Pattern
SL01, SL01B / SL02, SL02B
SL03, SL03B
Manual
1
1
1
INSTRUCTION MANUAL
Lens
shields
Detector
Detector
Wood screws
Φ4x25.4MM
+Rubber
washers
Wood screws
Φ4x25.4MM
+Rubber
washers
3
Manual
1
Lens
shields
SL01/SL01B/SL02/
SL02B/SL03/SL03B
Φ3.5 x 10MM
Screws
Rubber
washer
Rubber
washer
1 PACKAGE CONTENTS
SL01, SL01B, SL02, SL02B, SL03, SL03B are passive infra
red sensors to switch various types of load upon detection
of movement. Suitable for indoor or outdoor use and used
in residential or commercial environments.
MOTION DETECTOR LIGHT CONTROL
SL01/SL01B/SL02/
SL02B/SL03/SL03B
MOTION DETECTOR LIGHT CONTROL
SL01/SL01B/SL02/
SL02B/SL03/SL03B
MOTION DETECTOR LIGHT CONTROL
1
Corner
mounting
bracket
Rated Voltage
230V~ 10% 50/60Hz
230V~ 10% 50/60Hz
230V~ 10% 50/60Hz
CHALLENGER_SL01/SL01B/SL02/SL02B/SL03/SL03B
_Instructions_Rev01
3.28.0218401810101
LEDs OFF.
Load ON
2sec, then
OFF.
Test
mode
Warning
OFF
Watch
1S.
W
W
W
Load ON.
No test
mode
YES
Warning
OFF
Watch
1S.
LEDs all OFF.
LEDs all
OFF.
Load OFF.
W
W
2sec
2sec
5 TROUBLE SHOOTING
If the detector is not functioning correctly, please check the
following table for assistance:
Problem
Lighting
device
does
not turn
on
Nuisance
triggering
Lighting
device
does not
turn off
LED
notondoes
turn
Possible cause
1.Exceeding the
detection
range.
2.No power
supplied.
3.TIME knob is
not located to
TESTposition.
4. Wired
incorrectly.
1. time
setting.
2.D is
nuisance
triggered.
3.Wired
incorrectly.
Incorrect
etector
There are heat
sources, highly
reflective objects
or any objects
which may be
swayed in the
wind within the
detection
coverage.
1. Power does
not turn on.
2. Wired
incorrectly.
3. LUX Knob
incorrectly.
4. Malfunctioned
load.
adjusted
Suggested solution
1. Walk in the effective
detection range
2. Switch on the power.
3.TIME knob must be
located toTEST position.
4. Refer to wiring diagrams.
1.To test the delay time
specified onTIME
check is
triggered if lighting device
off as the delay time is up.
2. Keep away from detection
coverage to avoid activating while doing
test.
3. Make sure load and wires
are connected correctly.
knob
and
nuisance
does not turn
the
detector
detector
Avoid aiming the
toward any heat sources,
such as air conditioners,
electric fans, heaters or any
highly reflective surfaces.
Make sure there are no
swaying objects within the
detection coverage.
detector
1. Switch on the power.
2. Refer to wiring diagrams
( FIG.5) and
oad is malfunctioned.
check if t he
l
3. Check if LUX knob are set
the correct position.to
4. Replace the disabled load
with a new one.
NOTE
The following conditions may cause lower sensetivity:
In very foggy conditions, the sensitivity may be reduced
due to moisure collating on thelens.
In very hot conditions, the sensitivity may be reduces as
high ambient temperature could be close to body
temperature.
In cold conditions when heavy clothing is used, very little
heat is emitted from the body (especially if face is covered)
Cleaning: Wipe with dry cloth only. Soap or roughcloth
may damage the detector lens.
FIG.22
FIG.23
Slot path
Distributed by:
CHALLENGER SECURITYPRODUCTS
10 Sandersons Way, Blackpool, FY4 4NB
Email enquiries.challenger@adivision.co.uk
Website: www.challenger.co.uk
:
RoHS
Conform
CAUTION!
Due to our policy of continuous improvement we reserve
the right to change specification without prior notice.
Errors and omissions excepted.
These instructions have been carefully checked prior to
publication. However, no responsibility can be accepted
by Challenger for any misinterpretation of these
instructions.
CHALLENGER_SL01/SL01B/SL02/SL02B/SL03/SL03B
_Instructions_Rev01
Loading...