Page 1
Smart Anti-theft Alarm System
Installation and Operation Manual
ADWC
SOS
Page 2
Installation Safety
1. Keep children and bystanders away while installing the products.
2. The Alarm PIR Unit must be mounted in a location free from vibration as
unwanted alarm conditions will occur.
3.Wear ANSI-approved safety goggles during installation.
4. This product is not a toy. Mount it out of reach of children.
Operation Safety
1. Do not operate electrically powered products in explosive atmospheres, such as
in the presence of flammable liquids, gases, or dust. Electrically powered
products create sparks which may ignite the dust or fumes.
2. The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
3. Do not expose the product to rain or wet conditions. Water entering the Power
Adapter will increase the risk of electric shock.
Alarm PIR Unit
Speaker
Battery indicator
(Low battery the LED light)
PIR
Base
Function:
1. Receiving and processing remote control.
2. Alarm bells
3. Doorbell rings
Arm button
Disarm button
Register button
Packing List
Alarm PIR Unit
SOS
Remote control
Mounting Screw
1
User Manual
Transmission Frequency
Quantity
Ring Time
Alarm sound intensity
Supply Voltage
Operating current
Detection distance
Detection angle
Battery Installation
868.35 Mhz
1
about 30 seconds
100db (Distance: 30 cm)
6V(1.5V 4pcs) AA battery
70mA~100mAH
0~5m
0
120
2
Page 3
REMOTE CONTROL
Learning remote control
Battery indicator:
Arm button: click the button, the system enter arming status
Disarm button: Click the button, the system enter disarming status
SOS
Function:
Bell button: Click the button, the system enter doorbell mode
SOS button: click the button,the alarm will sound on the PIR unit.
Remote Host conversion mode
Transmission Frequency
Transmission Distance
Supply Voltage
Operating current
The total number coding
Battery Installation
SOS
Low battery the LED light
868.35 Mhz
0~150m
3V CR2032 battery
5mA~6mAH
1000000
Clears the original component identification code to enter this feature! When you need to replace
the components need to use this feature!
SOS
1. Keep on press button
about 5 seconds
3. press button on the
remote control the
LED turn off on the host
2.The LED light
on the host
. press button
to exit learn model.
Note: Only learn one remote unit at a time.
PIR+PIR Alarm Unit
50~
SOS
1.press the button on the host
or keep on press button on
remote control until ring "DI" tone .
2.Host sound "DI" tone
3.Wait about 50~70 seconds
until the host response "DI"
tone, enter the armed status
70
4.when the host is triggered
3
5. Wait about 10 seconds 6. The host enters alarm
status (about 30 seconds)
4
Page 4
SOS
7.press the button on the host
or button on remote control to
stop the alarm and disarm
SOS alarm
Due to our policy of continuous improvement we reserve the right to change
specification without prior notice. Errors and omissions accepted. These instructions
have been carefully checked prior to publication. However, no responsibility can be
accepted by Challenger Security Products for any misinterpretation of these
instructions.
SOS
1. Press the SOS button
NOTICE: If there is no in operation ,after the alarm ends to enter the theft mode.
2. The host enters alarm status
(about 30 seconds)
3.press the button on the host
or button on remote control to
stop the alarm and disarm
Doorbell function
SOS
1.press the button on the host or keep on press
button on remote control until ring "Ding Dong" tone .
3. Host ring "DINGDONG" sound
5
2. When the host is triggered
SOS
CHALLENGER SECURITY PRODUCTS
10 SANDERSONS WAY, BLACKPOOL, FY4 4NB
Email:
Website:
enquiries.challenger@adivision.co.uk
www.challenger.co.uk
RoHS
Challenger_AWDC_Instructions_Rev01
Loading...