Cecilware FE100G General Manual

FE100G

Automatic Coffee Urn

OPERATION MANUAL

Contents

SPECIFICATIONS
INSTALLATION
ADJUSTMENTS
OPERATING INSTRUCTIONS
MAINTENANCE TIPS PARTS LIST
ILLUSTRATIONS WIRING
DIAGRAMS

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND

LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

THIS INSTALLATION MUST CONFORM WITH THE NATIONAL

FUEL GAS CODE ANSI Z223.1 (Latest Edition).

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION OR

MAINTENANCE CAN CAUSE PROPERTY DAMAGE. INJURY OR DEATH.

READ THE INSTALLATION. OPERATION AND MAINTENANCE

INSTRUCTIONS THOROUGHLY BEFORE INSTALLING

OR SERVICING THIS EQUIPMENT.

Every Ceclware product has been carefully inspected before shipment. The finest of materials and the highest
standards of workmanship have been but into the equipment.
Within 1 year of purchase, should any Cecilware product show defect in factory workmanship or material, we agree to
Repair, at our option or replace without cost to user such parts which prove upon factory inspection to have been so
defective. All equipment must be shipped transportation charges prepaid for acceptance. This warranty covers
replacement parts only, labor charges are covered for 90 days after installation.
This warranty does not apply under the following conditions:

• neglect or abuse of equipment

• excessive lime condition

• Improper installation

• any outside modification to equipment
Every Cecilware urn body is covered for three years. This warranty covers the stainless steel body
and stainless steel liners only.
Portable equipment such as Electric Fryers, Food Warmers, Electric Stoves, Dispensers, Plug-In
Urns, Coffee Brewers and Warmers must be returned to the factory or brought to an authorized
service station for repair.

WARRANTY

CECILWARE CORPORATION

43-05 20th Avenue, Long Island City, N.Y. 11105 • 718-932-1414

N529A-4/92

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER
FLAMMABLE VAPORS AND LIQUIDS IN THE
VICINITY OF THIS OR ANY OTHER APPLIANCE.

SAFETY PRECAUTIONS

FOR YOUR SAFETY, THE FOLLOWING SAFETY PRECAUTIONS

SHOULD BE FOLLOWED AND ENFORCED.

1. Instructions must be posted in a prominent location and all safety precautions taken in the event the
user smells gas. Obtain this information from your local gas supplier.

IF YOU SMELL GAS:

1. OPEN WINDOWS 3. EXTINGUISH ANY OPEN FLAMES

2. DON'T TOUCH ELECTRICAL SWITCHES 4. IMMEDIATELY CALL YOUR GAS SUPPLIER

2. Lighting - Follow instructions on label attached to side of urn, or see page 2.

3. This appliance is equipped with a three prong (grounding) plug for your protection against shock hazard and

should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding
prong from this plug.

4. A wiring diagram of the control is located on the inside of the removable control box panel.

5. Do not place anything over the flue opening.

6. Do not place combustibles or non-combustible materials in the vicinity of the urn as this could cause fires or

obstruct air to the main burners.

7. This installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code ANSI Z223.1 latest edition.

8. Provide adequate air supply and ventilation.

9. Provide adequate clearance for air openings into the combustion chamber.

10. Provide clearances for servicing and proper operation.

11. This appliance must be electrically grounded in accordance with local codes, or in the absence of local codes,
with the National Electrical Code ANSI/NF PA No. 70 latest edition.

12. FOR USE ON NON-COMBUSTIBLE FLOORS - MINIMUM CLEARANCE FROM COMBUSTIBLE
CONSTRUCTION 6" FROM SIDE - 8" FROM BACK.

13. Urn must be disconnected from gas supply during any pressure testing of pipelines in excess of 1/2 psig, and
isolated (by turning off manual gas shut -off valve) during any testing equal to or less than 1/2 psig.

14. Retain this manual for future reference.

1

FE-100
Gas

SPECIFICATIONS

Dimensions

Body Depth 16"
Overall Depth

to faucet centers: 19 1/2"
Working Height 26"
Overall Height: 31"
Overall Width: 37 1/2"
Water Connection: 1/4" tubing
Constructed of type 304,

18-8 Stainless Steel
Approx Ship Wt; 125 Ibs.

Performance 15 gals. per hr.
Gas Data 32,000 BTU. Natural & Propane

Electrical Data 120V. 3 amps

plug-in for

electrical
accessories

Note: Use TOSSAWAY- PAPER FILTERS No. 718

INSTALLATION INSTRUCTIONS

FE-100G GAS AUTOMATIC

SPECIFICATIONS:

Natural Gas - 32,000 BTU @ 4" W.C. Pressure Electrical Connections — Cord Type Plug-in
Propane Gas- 32,000 BTU @ 10" W.C. Pressure 120 Vac, 15 Amp — 50/60 Hz

Power Requirement — 3A @ 120V 50/60 Hz

INSTALLATION:

CAUTION: Examine the gas specifications label attached to the urn to be certain that the type of I)JS for which the unit is equipped is the

same as the gas supply.

It is essential to leave a minimum clearance of 6" from the side walls and 8" from the rear wall.
Machine is supplied with a water strainer (23) and a 19" length of 1/4" (outside diameter) copper tubing with a flare fitting. Connect the copper
tubing with the flare fitting to the water connection at the rear of the machine. The other end of the strainer is connected with a suitable length
of '/4" tubing and shut off valve (supplied by a plumber) to a cold water supply. Water pressure should be a minimum of 20 Ibs. for proper
operation.

Before connecting the gas line, turn on the water supply valve and insert the line cord into a 120V grounded outlet. The water will start entering

the urn and the water filling operation will be going on while the gas connections are made, thus saving installation time.
Connect the 3/8" gas line to the gas shut-off valve (1) located at the rear of the thermostat control. Check all gas connections with soap solution

before attempting to light urn.

LIGHTING AND ADJUSTMENTS - (Refer to Illustration 1) Water must be visible in the gauge glass before lighting pilot.

Turn on the main gas valve and set the thermostat dial to the desired temperature. Turn the gas cock valve (9) on top of the thermostat to the
"pilot" position. Insert a lighted match through the opening located on the bottom of the urn and depress the pilot button (10) while lighting the
pilot. Hold down the pilot button for at least 30 seconds and release. The pilot will remain lit.

NOTE: It may be necessary on the first lighting to hold the pilot button for a longer period to allow the trapped air to escape from the lines. Turn
the gas cock valve (9) to the "ON" position and the burner will light.

2