Congratulations on the purchase of your Cecilware Griddle/Cheesemelter. Please take a few moments to
carefully read through this manual to ensure that the machine is operated and maintained properly. This
will enable the best possible performance from this product for many years.
Cecilware will not accept liability for the following if:
* The instructions in this manual have not been followed correctly.
* Non-authorized personnel have tampered with the m achine.
* Non-original spare parts are used.
* The machine has not been handled and cleaned correctly.
Packaging
Cecilware prides itself on quality and service, ensuring that at the time of packin g all product s are supplied
fully functioning and free of damage.
Should you find any damage that occurs in transit, please contact your Cecilware dealerimmediately.
Installation
Remove the Cecilware Griddle/Cheesemelter from the packaging. Be certain that all protective plastics
and residues are thoroughly cleaned from its surface.
Place the Cecilware Griddle/Cheesemelter on a firm level surface; the adjustable feet can assist in
leveling.
Local standards and regulations should be consulted in order to abide by standards set in relation to
positioning, spacing and ventilation. Cecilware recommends that you allow no less than 4” ventilation gap
around the perimeter of this unit. Common sense and initiative should be used when choosing a position
and operating of this product.
Caution:
Do not position or operate near combustible materials/flammable objects.
Once your Griddle/Cheesemelter has been placed into position, be sure that the st ainless ste el waste and
crumb trays have been correctly positioned.
Supply the appropriate power and connect to source; your Griddle/Cheesemelter is now ready to turn on
and operate. (For power supply, please see technical specification sheet, page 10)
Preparing the cooking surface:
Be sure the cooking surface is clean; then simply turn the unit on and apply a generous amount of oil to
the plates, using the thermostat setting of 230º F for the grill. Once the grill has reached that temperature,
switch off and wipe the plates clean of excess oil.
The Cheesemelter part of this unit does not need any preparation; it is ready to use.
Caution: The grill and oil will be HOT!!!!!!
2
Operation
Your Griddle/Cheesemelter should be turned on prior to usage to al low the cooking surface to warm up; 5
minutes should be sufficient.
To get efficient use out of this unit while in intermittent use, it is recommended that the thermostat be
turned down, when not cooking. This will assist in reducing power consumption and also allow for a
quicker heating response when needed.
Cecilware recommends that the cooking surface be lightly greased before each use. For ch eesemelting or
finishing, simply adjust the grilling grid to your needs beneath the hotplate and element.
Turn the thermostat dial towards the “ON” position. T he amber pilot light will activate to confirm this; adjust
the dial to the required setting. As the grill plate fluctuates in temperature, the thermostat will operate to
maintain set temperature and the light will continue to indicate when the elements are heating or have
reached the required temperature. Both the cheesemelter and the grill plate run off the one element and
thermostat.
A temperature setting of between 375º F and 430º F will be sufficient for general cooking. This may vary
for a particular food type, individual needs, or experience.
Simply place the food products on the grilling surface and cook to your needs. For cheesemelting or
finishing, place the food products on the grilling grid supplied and slide into the unit.
Cleaning, Care and Maintenance
*Switch the power off and disconnect from power source when cleaning.
*The Griddle/Cheesemelter should be cleaned regularly throughout use, and thoroughly cleaned after
each meal period. Regular cleaning will result in easier cleaning, as the build up of waste food particles
will be less. Correct preparation of the cooking surface when first used will assist in keeping the plates
clean.
*For best results, clean the plates while still warm using warm soapy water. A nylon cleaning cloth can be
used, but it is recommended that steel wool etc. be avoided, as they will damage the plates. Do not use
cold water on warm plates; a buckling effect may occur.
*When scrubbing the plates, take care not to clean back too far. If you do, you may have to prepare the
cooking surface again before use.
*Remove the waste and crumb trays from unit and discard waste; clean in hot soapy water.
*The remainder of the Griddle/Cheesemelter can be cleaned with a damp cloth u sing h ot, soapy water.
*Warm soapy water is recommended for cleaning, cleaning agents after prolonged use can damage
stainless steel.
3
Safety
*A Cecilware Recommended Qualified Service Technician should carry out repairs if necessary. Do not
remove any components or service panels on this product.
*Switch off power to and disconnect from the power source while cleaning.
*Allow the Griddle/Cheesemelter to cool down after using before dismantling for cleaning; the unit will still
be too hot to handle immediately after use
.
*Do not immerse in water or use hose to clean.
*If the power cord is damaged, it must be replaced by a Cecilware Recommended Qualified Service
Technician in order to avoid a hazard.
Trouble Shooting
If your Cecilware Griddle/Cheesemelter does not operate, please check the following before placing a
service call.
Griddle with Cheesemelter EL-1624T, EL-1636T
Problem Cause Remedy
The unit is not working and the
indicator light is not on
The unit is heating but the
indicator light is not on
1. Mains power supply 1. Check mains power supply
2. Power switch has not
been turned on
3. Fuse in the plug has
blown
4. Plug and lead are
damaged
5. Internal wiring fault
6. Thermal cut-out has
activated
1. The indicator bulb has
blown
2. Check the unit is correctly plugged in
and turned on
3. Replace the fuse in the plug with
correctly rated fuse
4. Call service agent or qualified
technician
5. Call service agent or qualified
technician
6. This is a safety device that has
disconnected the power: call a service
agent or qualified technician
1. Replace the indicator light: call a
service agent or qualified technician
4
Trouble Shooting Cont…
Problem Cause Remedy
Indicator light is on but the unit
is not heating
1. Faulty element(s)
1. Call service agent or qualified
2. Ensure that the thermostat is set
2.Operation of
thermostat
3. Faulty thermostat
3. Call service agent or qualified
technician
correctly, also ensure the dial is not
spinning on the thermostat and
giving the wrong reading
technician
1.Carbon build up
1. Ensure that the plates are kept clean
and free of carbon build up
2. Ensure that the thermostat is set
Slow heat up of the cooking
surfaces
Please ensure:
*There is correct power supply.
*The machine is plugged in correctly and power is switched on.
*The timer and thermostat are in the correct position.
*The elements are clear of any food waste.
Note: All Cecilware products are tested prior to packing.
2. Thermostat setting
3. Faulty element(s)
correctly, also ensure the dial is not
spinning on the thermostat and
giving the wrong reading
3. Call service agent or qualified
technician
Compliance
Cecilware products have undergone strict product testing in order to comply with regulatory standards
and specifications set by international, independent, and federal authorities.
As testimony to such compliance, Cecilware products carry the following marks/symbols:
5
Electrical Diagram
Model: EL-1624T:
thermostat
240V
on/off
switch
pilot light
heating
element
EL-1636T:
240V
on/off
switch 1
thermostat 1
pilot light 1
heating
element 1
on/off
switch 2
thermostat 2
pilot light 2
heating
element 2
The above circuit diagram has been provided to assist qualified technicians. A Recommend Qualified
Service Technician should carry out repairs if needed. Do not remove any components or service panels
on this product.
6
Explosion View
MODEL: EL -1624T
2
3
4
5
6
7
8
14
9
10
11
13
12
7
MODEL: EL – 1636T
2
3
4
14
13
12
11
5
6
10
7
8
9
8
Spare Parts List
No. Description
1 GRIDDLE PLATE 1 NA 1 NA
2 ELEMENT CLAMP (UPPER) 2 NA 2 NA
3 ELEMENT FIXING PALTE 1 08036 2 08043
4 ELEMENT CLAMP (LOWER) 3 NA 4 NA
5 THERMOSTAT 1 08078 2 08078
6 PILOT LIGHT 1 08067 2 08067
7 THERMOSTAT DIAL 1 08041 2 08041
8 GRILLING RACK 1 08037 1 08044
EL-1624T EL-1636T
QTY Part NO. QTY Part NO.
9 CRUMB TRAY 1 08038 1 08045
10 ON/OFF SWITCH 1 08054 2 08054
11 DRIP TRAY 1 08039 1 08039
12 FEET 4 080040 4 08040
13 BASE PLATE 1 NA 2 NA
14 CORD AND PLUG 1 08047 1 08047
*NA = not available except by special order.
9
Specifications
CECILWARE
MODEL
EL-1624T 2400
EL-1636T
VOLTAGE
240V 60HZ
POWER
(watts)
3600
DIMENSIONS (inches)
W×D×H
×22”×12 1/4”
24”
×22”×121/4”
36”
10
CECILWARE CORPORATION
43-05 20th AVENUE, LONG ISLAND CITY, NEW YORK 11105-1295 ■
718-932-1414 FAX 718-932-7860 www.cecilware.com
11
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.