Page 1
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu
rv961 Range Cooker
Manual for Installation, Use and Maintenance
Page 2
2
Important
This appliance must only be used for the purpose for which it is
intended, i.e. domestic cooking. Any other use could be dangerous
and may lead to premature failure of the appliance.
The CDA Group Ltd cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product. Please note
that CDA reserve the right to invalidate the guarantee supplied with
this product following incorrect installation or misuse of the appliance.
This appliance is not designed to be used by people (including
children) with reduced physical, sensorial or mental capacity, or
who lack experience or knowledge about it, unless they have had
supervision or instructions on how to use the appliance by someone
who is responsible for their safety.
Under no circumstances should any external covers be removed for
servicing or maintenance except by suitably qualified personnel.
Appliance information:
Please enter the details on the appliance rating plate below for
reference, to assist CDA Customer Care in the event of a fault with
your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number
Page 3
3
CE Declarations of Conformity:
This appliance has been designed, constructed and marketed in
compliance with safety requirements of EEC Directive 2006/95/
EEC (Low voltage) and requirements of EMC Directive 2004/108/EEC.
This appliance has been manufactured to the strictest standards and
complies with all applicable legislation, including Electrical safety (LVD)
and Electromagnetic interference compatibility (EMC). Parts intended
to come into contact with food conform to EEC/89/109.4
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as
urban waste. It must be taken to a special local authority dierentiated
waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving from
inappropriate disposal and enables the constituent materials to be
recovered to obtain significant savings in energy and resources. As a
reminder of the need to dispose of household appliances separately,
the product is marked with a crossed-out wheeled dustbin.
Page 4
4
User Information
• Read the instructions carefully before using the cooker.
• Keep the instructions in a safe place for future reference.
• Follow the instructions for first use (page 6).
• Always use oven gloves when removing shelves and trays from the
cooker.
• Always grill with the door closed.
• Do not grill food containing fat without using the grill pan grid.
• Do not use the grill pan for roasting.
• Do not place cooking utensils or plates directly on the oven base.
• Do not cover the grill pan grid or the oven walls with aluminium foil.
• Do not store inflammable substances or items that cannot withstand
heat (such as wood, paper, cloths, spray cans, etc.) in the storage
drawer.
• Do not attempt to repair the internal workings of your oven.
• Cookers become hot during and immediately after use. Do not
touch the oven internal parts or the hob until the appliance has
been allowed to cool.
• After use, ensure that all the control knobs are switched o.
• Keep children away from the cooker when in use and immediately
after use.
• This cooker has been designed for use only as a cooking appliance.
Any other use (e.g. heating rooms) should be considered incorrect
and therefore dangerous.
• Never put cooking foil or plastic materials on the ceramic surface
when the hob is hot. These materials could melt and cause damage
to the hob.
• Never use the hob top for storage.
Page 5
5
• Pan handles should never stand out beyond the edge of the
worktop. This will help ensure children cannot reach them.
• Do not use pans with rough bases (e.g. cast iron) as these may
scratch the hob surface.
• Do not switch on the hob zones without cookware in place.
• Do not lean over the hob when it is in use.
• Follow the cleaning instructions carefully.
• Ensure any base of the saucepan is clean and dry before placing it
on the hob to prevent damage to the surface of the hob.
• The appliance is not intended to be operated by any means of an
external timer or separate remote-control system.
• Do not use the hob if the glass surface is cracked or damaged,
to prevent risk of electric shock. Disconnect it from the power
supply.
When correctly installed, your product meets all safety
requirements laid down for this type of product. However, special
care should be taken around the rear or the underneath of the
appliance as these areas are not designed or intended to be
touched and may contain sharp or rough edges that could cause
injury.
Page 6
6
Before First Use
Before using the ovens for the first time we recommend that you
clean them with soapy water, rinse carefully and then heat on each
of the below programmes at maximum temperature for the specified
time. A slightly unpleasant smell may be produced, caused by grease
remaining on the oven elements from the production process.
Please note:
• This range cooker has been fitted with a cooling fan to achieve
maximum eciency and to maintain low surface temperatures. The
cooling fan will switch on automatically when the ovens reach a
preset temperature and switch o automatically when the ovens
have cooled suciently, even after the ovens are switched o.
• The range cooker is equipped with a safety thermostat which will
switch o the ovens to prevent overheating. Overheating can be
caused by incorrect use of an oven or defective components. If
an oven switches o due to overheating, wait for the oven to cool
down before using it again. If the error continues, contact CDA
Customer Care.
15 minutes grill 60 minutes fan oven
60 minutes
conventional oven
Page 7
7
Fig. 1
Hob:
1. Front left dual zone 1.0/2.2kW / 140/210mm
2. Rear left zone 1.2kW / 140mm
3. Centre dual zone 1.1/2.0kW 140x250mm
4. Rear right zone 1.8kW / 180mm
5. Front right zone 1.2kW / 140mm
6. Residual heat indicators
Control panel:
7. Timer control
8. Left oven function control
9. Left oven temperature control
10. Right oven function control
11. Front left dual zone control
12. Rear left zone control
13. Centre dual zone control
14. Rear right zone control
15. Front right zone control
1
43
2
5
15
7 8 9 10 11 12 13 14
00 00
00 00
00
6
Page 8
8
How to Use the Hob
The ceramic surface of the hob allows fast transmission of heat
vertically from the heating elements under the glass to the pans on
the hob top.
The heat does not spread horizontally, so the hob top remains
relatively cool only a few centimetres from the zone in use.
Please note:
The heating elements are equipped with a temperature limiter that will
switch the element o to prevent damage to the hob.
The temperature limiter may also operate when incorrect pans
are used or pans are poorly positioned. This will aect cooking
performance.
The temperature limiter can be seen in the zone as the straight line
out from the centre of the element. This is not a fault with the hob.
Using the single zones
The heating element is formed of a coil of resistant material which
reaches the required cooking temperature quickly.
Before using the hob, first check the hob and the pan are clean and
dry, then place the pan correctly onto the zone.
The power level for each zone can be regulated by turning the
control knob to the required level between 0 (o) and MAX
(maximum).
Page 9
9
Using the dual zones
The dual zones are formed of two separate coils of resistant material.
To turn on the dual zone, turn the control knob fully clockwise to
the position.
Residual heat indicators
The hob is equipped with residual heat indicators which warn when
any of the zones are hot to the touch, both during and after cooking.
A light will show on the display to indicate a zone is hot until the zone
is at a safe temperature to touch, when the residual heat indicator will
switch o.
Please note:
You should avoid touching the zones when the hob is in use, or
when a residual heat indicator is on.
In the event of a power cut, the residual heat indicators will illuminate
after the power supply is restored. However, when there is no power
supply to the hob the residual heat indicators will not work, so extra
care must be taken.
Page 10
10
Ecient Use of Your Hob
The hob is equipped with zones of dierent sizes, designed to
accommodate most shapes and sizes of pan. For best results, only
use pans with flat bottoms and choose appropriate zones depending
on the sizes of the pans. The most ecient use of the hob is shown
below, where the pans and zones are correctly chosen.
Use pan lids where possible to minimize the energy usage of your
appliance.
Turn o each zone a few minutes before the end of cooking time.
The residual heat in the zones will continue to cook the food for the
remaining cooking time.
It is very important that the pans used on the hob are made of a
suitable material and have the correct type of base. The base should
be flat and smooth, as any rough part on the pan base could scratch
the ceramic hob top.
Zone Size Minimum Pan Size (cm) Maximum Pan Size (cm)
140 mm 14 16
180 mm 16 20
220 mm 20 24
fig.2
Page 11
11
Choose pans which are between the sizes recommended in the table
above, and with bases that are as non-reflective as possible, e.g. dull
and dark.
Only pans recommended for use on ceramic hobs should be used.
Pans with aluminium bases may leave silver streaks or spots on the
hob. Glassware and pans with rough circular machined bases should
not be used.
Please note:
At the end of cooking, remember to turn o the hob.
Page 12
12
Using Your Main Oven
Important
Cooking function knob
To choose the function, turn the cooking function knob clockwise to
the required setting.
Each of the oven functions uses dierent elements within the oven to
oer you the best choice of cooking every time.
These are explained below:
Oven Light
This function switches on the oven light without using any
heating elements, to illuminate the oven cavity.
The oven light remains on with every cooking function.
Fanned Grill
This function uses the fan to circulate the heat from the
grill element around the food.
The temperature must be set between 60ºC and Max.
Grill
This function radiates the heat from the grill element.
The temperature must be set between 60ºC and Max.
Page 13
13
For both grill functions please note:
• Always grill with the oven door closed.
• Put the grill pan as close to the grill as possible.
• Do not grill for more than 30 minutes at a time.
• Preheat the grill for approximately five minutes with the oven door
closed.
Conventional Oven
This function uses the upper and lower heating elements
with a temperature between 60ºC and Max.
Natural convection creates a perfect cooking zone in the
centre of the oven, ideal for dark fruit cakes and pastries.
Warming Oven
Using heat produced only by the bottom element, this
natural heat is perfect for dough proving and blindbaking.
Fan Assisted Oven
Using the circular element and the fan with a temperature
between 60ºC and Max, this cooking function blows the
air into and around the oven cavity. Temperatures are
achieved quicker, reducing or even removing the need
for preheating. Both cooking temperatures and cooking
times can be reduced for a more energy ecient cooking
programme.
Page 14
14
Defrost
Using the fan only this oven function circulates the air
around the oven cavity, speeding up the natural defrost
process (1kg takes approximately one hour, depending on
the type of food).
Fan Oven
Using the circular element and the fan with a temperature
between 60ºC and Max, this cooking function blows the
air into and around the oven cavity. Temperatures are
achieved quicker, reducing or even removing the need
for preheating. Both cooking temperatures and cooking
times can be reduced for a more energy ecient cooking
programme.
Perfect for cooking various food types simultaneously as
foods are sealed quickly to prevent flavour transfer.
Temperature knob
• To set the temperature, turn the temperature knob
clockwise to the required temperature.
• Once the oven has reached the required temperature,
the temperature indicator lamp on the control panel will
switch o.
• The temperature indicator lamp will light up when the
oven elements are working.
• Turn the temperature knob fully clockwise for grilling.
Please note: Always ensure that you turn all the control knobs
back to their o positions after cooking.
Page 15
15
Programming the
Main Oven
Please note:
• The semi-automatic and automatic
cooking programmes will only work
with the main oven.
• The alert beep will cut o after
two minutes if it is not switched o
manually.
Setting the clock
The clock is preset to 12:00, and will revert to this after a power
failure.
When the current time indicator is flashing, touch or . When
the correct time is shown on the display, the clock will set after
approximately five seconds’ delay.
To change the clock once it has been set, touch repeatedly until the
current time indicator flashes, then touch or . When the correct
time is shown on the display, the clock will set after approximately five
seconds delay.
The minute minder
The minute minder can be used when the oven is switched on or o.
It can be set for up to 23 hours and 59 minutes.
To set the minute minder:
• Touch repeatedly until the minute minder indicator flashes.
fig. 1
5 6 7
1 Cooking time indicator
2 End of cooking time indicator
3 Minute minder indicator
4 Current time indicator
5 Decrease key
6 Mode key
7 Increase key
1 2 3 4
Page 16
16
• Then touch or to select the required duration for the minute
minder. When the correct duration shows on the display, either
touch or wait for approximately five seconds. The minute minder
indicator will remain lit to confirm the minute minder is on.
• When the countdown is complete, there will be an alert beep which
will continue for two minutes and the minute minder indicator will
flash. To switch o the alert beep, touch any key.
Please note:
At the end of the countdown, the minute minder will not switch o the
oven. Remember to turn o the oven manually.
Semi-automatic cooking
The main oven can be set to switch o automatically at a preset time
up to a maximum of 10 hours.
To set a semi-automatic cooking programme:
• Select the oven function and temperature (the oven will switch on)
• Touch until the cooking time indicator flashes.
• Then touch or to select the required duration for the semi-
automatic cooking programme. When the correct duration
shows on the display, wait for approximately five seconds. The
cooking time indicator will remain lit to confirm the semi-automatic
programme is on.
• When the cooking time is complete, there will be an alert beep
which will continue for two minutes and the cooking time indicator
will flash. To switch o the alert beep, touch any key.
Page 17
17
Please note:
At the end of the cooking programme, remember to turn o the oven
manually.
Automatic cooking
The main oven can be set to switch on and o automatically at preset
times up to a maximum of 10 hours.
To set an automatic cooking programme, follow the steps for setting a
semi-automatic programme above, and then:
• Touch until the end of cooking time indicator flashes.
• Then touch or to select the required end of cooking time.
When the correct time shows on the display, wait for approximately
five seconds. The cooking time and end of cooking time indicators
will remain lit to confirm the automatic programme is on.
• The oven will switch o until the automatic programme starts. When
the programme starts, the cooking time indicator will switch o
• When the cooking time is complete, there will be an alert beep
which will continue for two minutes and the end of cooking time
indicator will flash and the oven will switch o. To switch o the alert
beep, touch any key.
Please note:
At the end of the cooking programme, remember to turn the oven
controls to the o position manually.
Page 18
18
Using Your Second Oven
Control Knob
Important: The control knob does not rotate through a full 360°.
Rotate it clockwise from the “O” position to turn the oven on, then
rotate it anticlockwise back to the “O” position to turn the oven o.
Do not try to force the knob past the position.
To set the temperature of the second oven (conventional cooking
only), or to select the other functions, turn the control knob to the
required function.
Each of the oven functions uses dierent elements within the oven to
oer you the best choice of cooking every time. These are explained
below:
Conventional Oven
Turning the control knob clockwise to any of the temperature settings
around the dial switches on the conventional oven.
This function uses the upper and lower heating elements with a
temperature between 60°C and Max.
Natural convection creates a perfect cooking zone in the centre of the
oven, ideal for dark fruit cakes and pastries.
Warming Oven
This setting uses heat produced only by the bottom
element and is pre-set to 250°C.
This gives an ideal setting for cooking pizza.
Page 19
19
Browning Oven
Using only the top oven element pre-set at 250°C, this
uses convection heat for browning and crisping.
Ideal for cauliflower or macaroni cheese.
Grill
This function radiates the heat from the grill element.
The temperature is pre-set to maximum , for ecient
grilling.
When grilling please note:
• Always grill with the oven door closed.
• Put the grill pan as close to the grill as possible.
• Do not grill for more than 30 minutes at a time.
• Preheat the grill for approximately five minutes with the oven door
closed.
Temperature Control
Once the oven has reached the required temperature, the
temperature indicator lamp on the control panel will switch o.
The temperature indicator lamp will light up when the elements are
working.
Please note: Always ensure that you turn the control knob to its
o position after you nish cooking.
Page 20
20
Cleaning The Cooker
IMPORTANT:
Always disconnect the appliance from the power supply before
undertaking any cleaning or maintenance.
You should always allow the cooker to cool fully after use before
undertaking any cleaning or maintenance.
• Steam cleaners must not be used when cleaning this appliance
• Clean the cooker regularly and remove spills as soon as they occur.
• Do not allow fat or oils to build up on the hob or in the oven.
• Do not place hot enamel parts (e.g. grill pan) in water. Leave them
to cool first.
• Do not allow vinegar, coee, milk, saltwater, lemon or tomato juice
to remain in contact with enamel parts.
• Do not use abrasive or corrosive cleaners (including scouring
pads) as these could scratch the appliance, remove control panel
markings or damage the cooker.
• Do not clean the removable parts of the cooker in a dishwasher,
these must be washed by hand.
For the glass and stainless steel surfaces, you should use a
nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch
the surface and could erase the control panel markings. Stainless
steel can be eectively cleaned by simply using a dilute solution of
water and mild detergent and drying to a shine with a clean cloth.
Page 21
21
Over time with use, the stainless steel surface may discolour; this is
normal and does not constitute a fault with this appliance. Proprietary
stainless steel cleaners are available.
Cleaning the Hob
You should use a non-abrasive cleaner to clean the hob top. Any
abrasive cleaner (including Cif) will scratch the surface and could
erase the markings.
Do not use steel wool, abrasive sponges or sharp utensils such as
knives to clean the hob as these could damage the hob. The hob
surface and the pans must be clean.
Carefully remove any food remains (especially those containing sugar),
dirt etc. as soon as is possible after spillage - using a ceramic hob
scraper if necessary whilst the zone is still hot.
Sugar/syrup mixtures could permanently pit the hob surface if left
to burn on. Once they have cooled and hardened they become
increasingly dicult to remove.
All cleaner residues should be removed with a damp cloth.
Types of residues Clean with Cleaning advice
Light
Cleaning sponge and
soft cloth
Wipe over the zone to be cleaned with a sponge and hot
water, and then wipe o with a soft dry cloth.
Accumulated baked-on stains/
dirt, sugar spills or melted
plastics
Cleaning sponge or
glass scraper and soft
cloth
Wipe over the zone to be cleaned with a sponge and hot
water, using a ceramic scraper to remove any large marks
or stains and then wipe o with a soft dry cloth.
Rings and hard water residues
White vinegar and soft
cloth
Pour a small amount of warm white vinegar onto the stain,
leave it to stand, and then wipe o with a soft dry cloth.
fast frying steaks
Page 22
22
Cleaning The Oven
Interiors
To clean the oven interior, suitable
proprietary chemical cleaners may
be used after first consulting with the
manufacturer’s recommendations and
testing a small sample on the oven
cavity.
Do not use metal scrapers or harsh
cleaners on the oven door glass.
These could cause scratches, which
may result in the glass shattering.
To remove the side racks, press down
on the top bar of the side rack to free
the rack from the top securing pin,
then remove the side rack by lowering
it out so that the hooks on the lower
edge are freed from the oven cavity (as
shown in fig. 8 and 9).
To replace the side racks, locate the
lower hooks in the oven cavity, then
pivot the side rack back into position,
pressing the top bar down to relocate it
against the securing pin.
fig. 9
fig. 7
fig. 8
Page 23
23
Removing The Oven
Doors
The oven door can easily be removed
as follows:
• Open the door to the full extent
(fig. 10).
• Open the lever A completely on the
left and right hinge (fig. 11).
• Hold the door as shown in fig. 14.
• Gently close the door (fig. 13) until left
and right hinge levers A are hooked
to part B of the door (fig. 12).
• Withdraw the hinge hooks from their
location following arrow C (fig. 13)
• Rest the door on a surface.
To replace the door, repeat the above
steps in reverse order.
fig.10
fig.11
fig.14
fig.13
fig.12
Page 24
24
Changing The Oven Lights
1. Disconnect the electrical power supply (for example, by switching
o the main isolator switch).
2. Unscrew the light cover.
3. Fit a new bulb.
4. Refit the cover.
Note:
Use only bulbs designed to resist up to 300°C with the following
characteristics: 230 V, type E14 and same power of the
replaced bulb (check watt power as stamped on the bulb itself).
If your cooker is not working
1. Check that the mains supply has not been switched o.
2. Check that the fuse in the spur has not blown.
Page 25
25
Installation
The manufacturer will not be held responsible for any damage
to property or injury to persons/animals resulting from incorrect
installation of this appliance.
We recommend you seek the help of another individual when
installing this appliance to prevent damage or injury.
Installation requirements
This range cooker is designed to be
installed flush with adjacent worktops
however in situations where the hob
top will be lower than the worktop
then a distance of 200mm should be
observed.
A distance of 500mm between the
range cooker and any adjacent
combustible materials (e.g. curtains)
should be observed.
A distance of 200mm between the
range cooker and adjacent vertical
surfaces should be observed.
This appliance is class 2/1 and is
suitable for installation adjacent to
furniture cabinets.
fig. 15
200min
900min
600
900
900
Page 26
26
If Fitting a Cooker Hood Above the
Range Cooker:
If a cooker hood is to be installed above the range cooker, the
height of the hood above the hob must be at least 650mm. If the
instructions supplied with the hood dictate that the hood must be
installed at a height greater than 650mm, then that height is the
minimum required.
Wall furniture requirements:
The minimum height of any cabinet immediately above the hob is
900mm. The minimum height of any adjacent
units (including light pelmets) is 450mm, unless they are manufactured
from a material resistant to fire (steel, for example)
Notes:
• Do not position this appliance adjacent to a refrigeration unit. The
heat generated may cause the refrigeration unit to fail.
• This appliance is designed to be installed adjacent to cabinet units
capable of withstanding temperatures of 65°C or greater above
ambient temperature.
Page 27
27
Anti-tilt bracket/chain
This appliance is supplied fitted with safety chains and wall mounted
brackets to prevent it tilting forwards. These should be fitted as part
of the installation.
You must ensure that the fixings are suitable for the wall type. Those
included may not be suitable in all situations.
Height adjustable feet
The adjustable feet must be fitted to the base of the range cooker
before use.
Rest the rear of the appliance on the packaging exposing the base to
fit the feet.
Fit the four legs by screwing them hand tight into the support base.
To prevent damage, lift the range cooker into position. Do not push it
across the floor unnecessarily.
Page 28
28
fig.17
Mains Electricity
Connection
Warning! This appliance must be
earthed
To connect this appliance to a UK
standard mains supply, connect the
bridging links between 1-2-3 for the live
feed and 4-5 for the neutral feed
We recommend that the appliance is
connected by a qualified electrician,
who is a member of the N.I.C.E.I.C. and
who will comply with the I.E.T. and local
regulations.
This appliance is intended to be
connected to xed wiring and is not
suitable for connection to a 13A plug
or 13A supply.
This appliance is intended to be
connected to fixed wiring by a double
pole switch, having a contact separation
of at least 3mm in all poles. The switch
must be positioned no further than 2m
from the appliance.
fig. 16
Green/yellow
Blue
Brown
1
2 3
4
Green and Yellow = Earth
(PE)
Blue = Neutral
Brown = Live
Page 29
29
Release the two locks located at either side of the connector cover at
the rear of the appliance.
Feed the mains lead through the cable clamp to prevent accidental
disconnection.
Tighten the cable clamp securely and close the connector cover.
Please note:
• The mains cable must only be replaced by a qualied electrician
or service engineer and must be of equivalent or better rating (i.e.
6.0mm², HO5RR-F or twin and earth).
• This appliance is intended to be connected to the mains supply with
a cable of cross section area 6.0mm². A larger cable will not fit the
terminal connections.
• The marking of the current rating of the fuse or circuit breaker
protecting this appliance should be marked on the socket outlet.
• Assembly and electrical connection should be carried out by
specialised personnel.
• When installing this product we recommend you seek the help of
another individual.
1. The wire which is coloured green and yellow must be connected to
the terminal marked E (Earth) or coloured Green.
2. The wire which is coloured blue must be connected to the terminal
marked N (Neutral) or coloured Black.
3. The wire which is coloured brown must be connected to the
terminal marked L (Live) or coloured Red.
Mains electrical voltage: 220 – 240Vac, 50 / 60 Hz
Total rated electrical consumption: 11.7 - 13.86 kW
Page 30
30
Page 31
31
E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the
right to change specifications without prior notice.
Page 32
Please contact our Customer Care Department for Service on the details below
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu
Loading...