CDA RC 9621 Series Manual For Installation, Use And Maintenance

Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY

T : 01949 862 012 F : 01949 862 003 E : [e-mail] W : www.cda.eu

RC 9621 .. Twin Cavity Ceramic Cooker

Manual for Installation, Use and Maintenance

2

Important

This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not
suitable for any non domestic application and therefore should not be used in a commercial environment.

The appliance guarantee will be void if the appliance is used within a non domestic environment i.e. a semi
commercial, commercial or communal environment.

The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of
this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product
following incorrect installation or misuse of the appliance.

Appliance Information:

Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the
event of a fault with your appliance and to register your appliance for guarantee purposes.

Appliance Model

Serial Number

Important Information for Correct Disposal of the Product in Accordance with ECDirective
2002/96/EC.

At the end of its working life, the product must not be disposed of as urban waste.
It must be taken to a special local authority dierentiated waste collection centre
or to a dealer providing this service.
Disposing of a household appliance separately avoids possible negative
consequences for the environment and health deriving from inappropriate
disposal and enables the constituent materials to be recovered to obtain signicant
savings in energy and resources. As a reminder of the need to dispose of household
appliances separately, the product is marked with a crossed-out wheeled dustbin.

Declaration of CE Conformity

This cooker has been designed, constructed and marketed in compliance with:

- Safety requirements of EU Directive “Low Voltage” 2006/95/EC;

- Protection requirements of EU Directive “EMC” 2004/108/EC;

- Requirements of EU Directive 93/68/EEC.

3

IMPORTANT SAFETY PRECAUTIONS AND RECOMMENDATIONS

IMPORTANT: This appliance is designed and manufactured solely
for the cooking of domestic (household) food and is not suitable for
any non domestic application and therefore should not be used in a
commercial environment.
The appliance guarantee will be void if the appliance is used within
a non domestic environment i.e. a semi commercial, commercial or
communal environment.
Read the instructions carefully before installing and using the
appliance.

– After having unpacked the appliance, check to ensure that it is not

damaged and that the oven door closes correctly.

In case of doubt, do not use it and consult your supplier or a professionally

qualied technician.

– Packing elements (i.e. plastic bags, polystyrene foam, nails, packing

straps, etc.) should not be left around within easy reach of children, as
these may cause serious injuries.

– Some appliances are supplied with a protective lm on steel and

aluminium parts. This lm must be removed before using the appliance.

– IMPORTANT: The use of suitable protective clothing/gloves is

recommended when handling or cleaning this appliance.

– Do not attempt to modify the technical characteristics of the appliance

as this may become dangerous to use. The manufacturer declines all
responsibility for any inconvenience resulting from the inobservance of
this condition.

– Do not operate your appliance by means of an external timer or separate

remote-control system.

– Do not carry out cleaning or maintenance operations on the appliance

without having previously disconnected it from the electric power
supply.

– WARNING: Ensure that the appliance is switched o before replacing

the oven lamp to avoid the possibility of electric shock.

4

– Do not use a steam cleaner because the moisture can get into the

appliance thus make it unsafe.
– Do not touch the appliance with wet or damp hands (or feet).
– Do not use the appliance whilst in barefoot.
– If you should decide not to use this appliance any longer (or decide to

substitute another model), before disposing of it, it is recommended

that it be made inoperative in an appropriate manner in accordance to

health and environmental protection regulations, ensuring in particular

that all potentially hazardous parts be made harmless, especially in

relation to children who could play with unused appliances.
– The various components of the appliance are recyclable. Dispose of

them in accordance with the regulations in force in your country. If the

appliance is to be scrapped, remove the power cord.
– After use, ensure that the knobs are in the o position.
– Children less than 8 years of age shall be kept away unless continuously

supervised.
– This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack

of experience and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way and understand

the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without

supervision.
– The manufacturer declines all liability for injury to persons or damage to

property caused by incorrect or improper use of the appliance.

– WARNING: During use the appliance and its accessible parts become

hot; they remain hot for some time after use.

– Care should be taken to avoid touching heating elements (on the hob

and inside the oven).
– The door is hot, use the handle.
– To avoid burns and scalds, young children should be kept away.

5

– Make sure that electrical cables connecting other appliances in the

proximity of the cooker cannot come into contact with the hob or
become entrapped in the oven door.

– WARNING: Unattended cooking on a hob with fat or oil can be

dangerous and may result in re. NEVER try to extinguish a re with
water, but switch o the appliance and then cover ame e.g. with a lid
or a re blanket.

– WARNING: Danger of re: do not store items on the cooking surfaces.
– Do not place or leave empty pans on the glass ceramic hob.
– Do not allow heavy or sharp objects to drop on the glass ceramic hob.
– Do not scratch the hob with sharp objects. Don’t use the hob as a work

surface.

– WARNING: If the hob is cracked or otherwise damaged by falling objects

etc., disconnect the appliance from the electrical power supply to avoid
the possibility of electric shock and call CDA Customer Care.

– WARNING: When correctly installed, your product meets all safety

requirements laid down for this type of product category. However
special care should be taken around the rear or the underneath of the
appliance as these areas are not designed or intended to be touched
and may contain sharp or rough edges, that may cause injury.

– FIRST USE OF THE OVEN - it is advised to follow these instructions:

– Furnish the interior of the oven as described in the chapter “CLEANING

AND MAINTENANCE”.
– Switch on the empty oven on max to eliminate grease from the heating

elements.
– Disconnect the appliance from the electrical power supply, let the

oven cool down and clean the interior of the oven with a cloth soaked

in water and neutral detergent; then dry carefully.

6

– CAUTION: Do not use harsh abrasive cleaners or sharp metal scrapers to

clean the oven door glass since they can scratch the surface, which may
result in shattering of the glass.

– Do not line the oven walls with aluminium foil. Do not place baking trays

or the drip tray on the base of the oven chamber.

– FIRE RISK! Do not store ammable material in the oven or in the storage

compartment.

– Always use oven gloves when removing the shelves and food trays from

the oven whilst hot.

– Do not hang towels, dishcloths or other items on the appliance or its

handle – as this could be a re hazard.

– Clean the oven regularly and do not allow fat or oils to build up in the

oven base or tray. Remove spillages as soon as they occur.

– Do not stand on the cooker or on the open oven door.
– Always stand back from the appliance when opening the oven door to

allow steam and hot air to escape before removing the food.

– SAFE FOOD HANDLING: Leave food in the oven for as short a time as

possible before and after cooking. This is to avoid contamination by
organisms which may cause food poisoning. Take particular care during
warmer weather.

– WARNING: Take care NOT to lift the cooker by the door handle.

7

Features and Technical Data

Vitroceramic Cooking Hob

1. 3 circuits cooking zone Ø 180 mm 1700 W

2. 3 circuits cooking zone Ø 145 mm 1200 W

3. Oval cooking zone Ø 145 x 250 mm 1800/1000 W

4. Double cooking zone Ø 210/120 mm 2100/700 W

5. 3 circuits cooking zone Ø 145 mm 1200 W

6. Cooking zone residual heat indicators

Attention:

Detach the appliance from the mains if the ceramic hob is cracked and contact CDA Customer Care.

2

1

3

5

4

Conventional
oven

Fig. 1

6

Multifunction
main oven

8

Control Panel

Controls Description

1. Front right cooking zone control knob

2. Rear right cooking zone control knob

3. Central cooking zone control knob

4. Rear left cooking zone control knob

5. Front left cooking zone control knob

6. Multifunction main oven switch control knob

7. Multifunction main oven thermostat control knob

8. Electronic programmer (main oven only)

9. Conventional oven thermostat control knob

10. Conventional oven switch control knob

Pilot Lamps:

11. Main oven thermostat indicator light

12. Conventional oven thermostat indicator light

13. Cooking hob ON indicator light

Please note: This appliance incorporates a safety cooling fan which you will hear operating whenever the
oven or grill are in use. The cooling fan may also operate when the oven is switched o. This fan is to reduce the
external temperature of the appliance and cool the internal components.

A
U
T
O

8 7 6 5 4 3 2 1

11

Fig. 2

10

9

13 12

9

Electronic Programmer (Main Oven Only)

The electronic programmer is a device that groups together the following functions:
– 24 hour clock with illuminated display
– Timer (up to 23 hours and 59 minutes)
– Programme for automatic oven cooking
– Programme for semi-automatic oven cooking.

Description of the buttons:

Symbols Description

Timer

Cooking time

End of cooking time

Manual position and cancellation
of the set cooking program

To increase the numbers on the
digital display

To decrease the numbers on the
digital display.

Description of the illuminated symbols:

Symbols Description

AUTO

ashing

Programmer in automatic
position but not programmed.

AUTO

always lit

Programmer in automatic
position with program set.

Automatic cooking taking place.

Timer in operation

and

AUTO

ashing

Program error.
(The time of day lies between the
calculated cooking start and end
time).

Note:

Select a function by the respective button and, in 5 seconds, set the required time with the

/ buttons
(“one-hand” operation).
After a power cut the display resets to zero and cancels the set programs.

A
U
T
O

Fig. 3 Fig. 4

10

Electronic Clock (g. 4)

The programmer is equipped with an electronic clock with illuminated numbers which indicates hours
and minutes. Upon immediate connection of the oven or after a power cut, three zeros will ash on the
programmer display.
To set the correct time of day it is necessary to push the

button and then the or button until you
have set the correct time. In another way push simul tane ously the two buttons and at the same time
push the or button.

Note: If the clock is reset it deletes any previously set programs.

Normal Cooking without the Use of the Programmer

To manually use the oven, that is, without the aid of the programmer, it is necessary to cancel the ashing
AUTO by pushing the button

(AUTO will be switched o and the symbol will go on - Fig. 5).
Attention: If the AUTO is steadily lit (which means a cooking program has already been set), the program can
be cancelled and switched to manual by pushing the button .
If the oven is switched on, you must switch o manually.

Electronic Timer

The timer program consists only of a buzzer which may be set for a maximum period of 23 hours and 59
minutes. If the AUTO is ashing push the button.
To set the time, push the button and the or until you obtain the desired time in the panel (g. 6).
Having nished the setting, the clock hour will appear on the panel and the symbol will be illuminated.
The countdown will start immediately and may be seen at any moment on the panel by simply pressing the
button .
At the end of the time, the symbol will disappear and the buzzer will sound and continue for approximately
7 minutes or until a button is pressed (not the / buttons).
After a short time the display will revert back to the time of day.

Setting the Frequency of the Audible Signal

The buzzer has 3 dierent tones and can be changed by pressing the button, but only when the time of
day is displayed.

Fig. 5 Fig. 6

11

Automatic Oven Cooking

To cook food automatically in the oven, it is necessary to:

1. Set the length of the cooking time

2. Set the end of the cooking time

3. Set the temperature and the oven cooking program.

These operations are done in the following way:

1. Set the length of the cooking period by pushing the

button and the button to increase, or to

decrease if you have passed the desired time (g. 7). The AUTO and the symbol will illuminate.

2. Set the end of the cooking time by pressing the

button (the cooking time already added to the clock

time will appear), and the button (g. 8); if you pass the desired time you may get back by pushing the

button.
After this setting, the symbol will disappear. If after this setting, the AUTO ashes on the display and
a buzzer sounds, it means there was an error in the programming, that is that the cooking cycle has been
superimposed on the clock. In this case, modify the end of cooking time or the cooking period itself by
following again the above mentioned instructions.

3. Set the temperature and the cooking program by using the switch and thermostat knobs of the oven (see
specic chapters).

Now the oven is programmed and every thing will work automatically, that is the oven will turn on at the right
moment to end the cooking at the established hour.
During cooking, the

symbol remains illuminated.

By pushing the button you can see the time that remains until the end of cooking.

The cooking program may be cancelled at any time by pushing

.

At the end of the cooking time the oven will turn o automatically, the

symbol will turn o, AUTO will ash
and a buz zer will be sound, which can be turned o by pushing any of the but tons except the / buttons.
Turn the switch and thermostat knobs to zero and put the programmer onto “manual” by pressing the
button.

Attention: After a power cut the clock resets to zero and cancels the set programs. After a power cut, three
zeros will ash on the display.

A
U
T
O

A
U
T
O

Fig. 7 Fig. 8

12

Semi - Automatic Cooking

This is used to switch the oven o automatically after the desired cooking time has elapsed.
There are two ways to set the semi-automatic cooking function:

1. Set the length of time you need to cook the food by pushing the

button and the button to advance,
or to go backwards (Fig. 9).
This sets the desired “stop” time.
AUTO and the symbol will be on.

or

2. Set the time you need the food to stop cooking by pushing the button and the button to advance, or
to go backwards if you have passed the desired time (Fig. 10).

AUTO and the symbol will be on.

Then set the temperature and the cooking program (see the relevant sections).
The oven is switched on and it will switch o automatically at the end of the desired time.
During cooking, the symbol remains on and by pressing the button you can see the time that remains
until the end of the cooking.

The cooking program can be cancelled at any moment by pushing the

button.

At the end of the cooking period, the oven and the

symbol will disappear, AUTO will ash and a buzzer will

sound and can be stopped by pushing any of the buttons except the / buttons.

Turn the function selector switch and thermostat knobs to zero and put the programmer onto “manual” by
pressing the button.

Attention: After a power cut the clock resets to zero and cancels the set programs. After a power cut, three
zeros will ash on the display.

A
U
T
O

A
U
T
O

Fig. 9 Fig. 10