Cda RC9620 User Manual
Twin cavity
ceramic cooker
RC 9620 ..
Users Operating Instructions
Installation instructions
Before operating this cooker,
please read these instructions carefully
2
Important:
This appliance is designed and manufactured solely for the cooking of domestic
(household) food and is not suitable for any non domestic application and therefore should not be used in a commercial environment.
The appliance guarantee will be void if the appliance is used within a non domestic environment i.e. a semi commercial, commercial or communal environment.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as
urban waste. It must be taken to a special local authority differentiated
waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources. As a
reminder of the need to dispose of household appliances separately,
the product is marked with a crossed-out wheeled dustbin.
Dear Customer
Thank you for choosing one of our appliances, carefully designed and built by
our specialist staff and thoroughly tested to satisfy your cooking requirements.
We suggest that you read this Instruction Booklet so that you will understand
fully how to operate your appliance.
Please keep the booklet handy. You may wish to refer to it at a later date.
CDA
Contents
Model RC 9620 ..
Page Number
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Assembling the backguard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features and technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electronic programmer (main oven only) . . . . . . . . . . . . . . . . . . . . . . . . . 7
How to use the vitroceramic hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
How to use the multifunction main oven . . . . . . . . . . . . . . . . . . . . . . . . 16
How to use the conventional oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Do’s and do not’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
For the installer
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Fitting the adjustable feet and levelling . . . . . . . . . . . . . . . . . . . . . . . 33-34
Stability bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Appliance servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3
4
Assembling the
backguard
Before installing the cooker,
assemble the backguard “V”
(fig. 1).
Please note that :
■ The backguard “V” can
be found packed at the
rear of the cooker.
■ Before assembling
remove any protective
film/adhesive tape.
■ The backguard must be
fixed to the cooktop using
the three supports “B”
supplied with the appliance (see fig. 1).
V
A
B
Fig. 1
Declaration of CE conformity
✓
This cooker has been designed, constructed and marketed in compliance with:
- Safety requirements of EU Directive "Low Voltage" 2006/95/EC;
- Protection requirements of EU Directive "EMC" 89/336/EEC;
- Requirements of EU Directive 93/68/EEC.
Introduction
Congratulations on your purchase of this CDA cooker which has been carefully
designed and produced to give you many years of satisfactory use.
Before using this appliance it is essential that the following instructions are carefully
read and fully understood.
We would emphasise that the installation section must be fully complied with for your
safety to ensure that you obtain the maximum benefits from your appliance.
5
Features and technical data
Fig. 2
2
1
3
5
4
Multifunction main
oven
Conventional
oven
Attention: Detach the
appliance from the
mains if the ceramic hob
is cracked and contact
the After-Sales service.
Vitroceramic cooking hob
1. 3 circuits cooking zoneØ 180 1700 W
2. 3 circuits cooking zoneØ 145 1200 W
3. Oval cooking zone Ø 145 x 250 1800/1000 W
4. Double cooking zone Ø 210/120 2100/700 W
5. 3 circuits cooking zoneØ 145 1200 W
6. Cooking zone residual heat indicators
6
Control panel
Fig. 3
87654 932110
Control panel - Controls description
1. Front right
cooking zone
control knob
2. Rear right
cooking zone
control knob
3. Central
cooking zone
control knob
4. Rear left
cooking zone
control knob
5. Front left
cooking zone
control knob
6. Multifunction main oven switch control knob
7. Multifunction main oven thermostat control knob
8. Electronic programmer (main oven only)
9. Conventional oven thermostat control knob
10.Conventional oven switch control knob
Pilot lamps:
11. Main oven thermostat indicator light
12. Conventional oven thermostat indicator light
13. Cooking hob ON indicator light
11 12
13
Please note: This appliance incorporates a safety cooling fan which you will hear
operating whenever the oven or grill are in use. The cooling fan may also operate
when the oven is switched off.
6
A
U
T
O
Electronic programmer (main oven only)
Fig. 5
Fig. 4
Description of the buttons:
Timer
Cooking time
End of cooking time
Manual position and cancellation
of the inserted cooking
programme
Advancement of the numbers of
all programmes
Turning back of the numbers of all
programmes and changing the
frequency of the audible signal.
Description of the lighted symbols:
AUTO - flashing - Programmer in
automatic position but not
programmed
AUTO - always lighted - Programmer
in automatic position with
programme inserted.
The electronic programmer is a device that groups together the following functions:
– 24 hour clock with illuminated display
–Timer (up to 23 hours and 59 minutes)
–Programme for automatic oven cooking
–Programme for semi-automatic oven cooking.
7
Automatic cooking taking place
Timer in operation
and AUTO - flashing - Programme
error.
(The time of day lies between the
calculated cooking start and end
time).
Note: Select a function by the
respective button and, in 5 seconds, set
the required time with the /
buttons (“one-hand” operation).
A power cut zeroes the clock and
cancels the set programmes.
A
U
T
O
Fig. 6
Fig. 7
Electronic clock (fig. 5)
The programmer is equipped with an
electronic clock with lighted numbers
which indicate hours and minutes.
Upon immediate connection of the
oven or after a blackout, three zeroes
will flash on the programmer panel.
To set the hour it is necessary to push
the button and then the or
button until you have set the exact
hour (fig. 5).
Alternatively, simultaneously push the
two buttons and at the same
time push the or button.
Note: Setting the clock deletes any
programme.
8
Normal cooking without
the use of the
programmer
To manually use the oven, that is, without
the aid of the programmer, it is necessary
to cancel the flashing AUTO by pushing
the button (AUTO will be switched off
and the symbol will go on - Fig. 6).
Attention: If the AUTO is not flashing
(which means a cooking programme has
already been inserted), by pushing the
button you have cancelled the
programme and switched to manual.
Electronic timer
The timer programme consists only of a
buzzer which may be set for a
maximum period of 23 hours and 59
minutes.
If the AUTO is flashing push the
button.
To set the time, push the button
and the or until you obtain the
desired time (fig. 7).
Having finished the setting, the normal
time will appear on the panel and the
symbol will appear.
The countdown will start immediately
and may be seen at any moment on
the panel by simply pressing the button
.
At the end of the time, the symbol
will be switched off and an intermittent
buzzer will go off; this can be stopped
by pressing any one of the buttons.
Altering the audible
signal
By pressing the button you can
choose from three variations.
A
U
T
O
Fig. 9
Fig. 8
9
Automatic oven
cooking
To cook food automatically in the oven,
it is necessary to:
1.Set the length of the cooking time
2.Set the end of the cooking time
3.Set the temperature and the oven
cooking programme.
These operations are done in the
following way:
1. Set the length of the cooking time by
pushing the button and the
button to
advance, or to go back
if you have passed the desired time
(fig. 8). The AUTO and the
symbol will be on.
2.Set the end of the cooking time by
pressing the button (the cooking
time already added to the clock time
will appear), and the button (fig.
9); if you pass the desired time you
may get back by pushing the
button.
After this setting, the symbol will
go off. If after this setting, the AUTO
flashes on the panel and a buzzer
goes off, it means there was an error
in the programming.
In this case, modify the end of
cooking time or the cooking time
itself by following the above
instructions again.
3.Set the temperature and the cooking
programme by using the switch and
thermostat knobs of the oven (see
specific chapters).
Now the oven is programmed and
everything will work automatically, that
is the oven will turn on at the right
moment to end the cooking at the
established time.
During cooking, the symbol remains
on.
By pushing the button you can see
the time that remains until the end of
cooking.
The cooking programme may be
cancelled in any moment by pushing .
At the end of the cooking time the
oven will turn off automatically, the
symbol will turn off, AUTO will flash
and a buzzer will sound, which can be
turned off by pushing any of the buttons.
Turn the switch and thermostat knobs
to zero and put the programmer onto
“manual” by pressing the button.
Attention: A power cut makes the
clock go to zero and cancels the set
programmes.
After a power cut three zeroes will flash
on the panel.
A
U
T
O
A
U
T
O
Fig. 10
Fig. 11
10
Semi-automatic cooking
This is used to automatically switch off
the oven after the desired cooking time
has elapsed.
There are two ways to set your oven:
1. Set the length of the cooking time by
pushing the button and the
button to advance, or to go
backwards if you have passed the
desired time (Fig. 10).
or
2. Set the end of the cooking time by
pushing the button and the
button to advance, or to go
backwards if you have passed the
desired time (Fig. 11).
AUTO and the symbol will be on.
Then set the temperature and the
cooking programme using the oven
switch and thermostat knobs (see
specific chapters).
The oven is switched on and it will
be switched off automatically at the
end of the desired time.
During cooking, the symbol
remains on and by pressing the
button you can see the time that
remains till the end of the cooking.
The cooking programme can be
cancelled at any moment by pushing
the button.
At the end of cooking, the oven and
the symbol will turn off, the AUTO
will flash and a buzzer will sound; that
can be stopped by pushing any of the
buttons.
Turn the switch and thermostat knobs
to zero and put the programmer onto
“manual” by pressing the button.
A
U
T
O
A
U
T
O
How to use the vitroceramic hob
Fig. 13
Fig. 12
The ceramic surface of the hob allows a
fast transmission of heat in the vertical
direction, from the heating elements
underneath the ceramic glass to the
pans sat on it.
The heat does not spread in the horizontal direction, so that the glass stays
“cool” at only a few centimeters from
the cooking plate.
The 5 cooking plates are shown by
painted disks on the ceramic surface.
3 circuit radiant zones
Incorporating 3 heating elements (fig.
13) you can control and light up all 3
together or separately by selecting from
the 6 positions on the control knob (fig.
12).
The working temperature required is
reached in a very short time.
11
Important note:
The heating elements incorporate a
thermolimiter that switches the element
ON/OFF during all the settings to protect the ceramic glass from overheating.
The use of incorrect pans and/or
wrong pan positioning will cause the
temperature limiter to operate more frequently, resulting in a reduction of
cooking performance.
Fig. 16
Fig. 15
Second element
Second element
Fig. 14
Double and oval radiant
zones
The heating element is formed of a coil
of resistant material which reaches the
working temperature quickly.
Operation of the cooking zone is controlled by a continuous energy regulator
from “1” to “12” (maximum temperature)
(fig. 14).
By switching on the second element (fig.
15 and 16), the surface area of the rear
right and central radiant zones can be
extended.
For this purpose, turn the control knob
(fig. 14)
fully to the right (position
).
12
Loading...