CDA RC 9000 User Manual

Dual fuel

cookers

RC 9000 ..

Users Operating Instructions

Installation instructions

GB

Before operating this cooker,

please read these instructions carefully

2

Important:

This appliance is designed and manufactured solely for the cooking of domestic
(household) food and is not suitable for any non domestic application and there­fore should not be used in a commercial environment.

The appliance guarantee will be void if the appliance is used within a non domes­tic environment i.e. a semi commercial, commercial or communal environment.

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.

At the end of its working life, the product must not be disposed of as
urban waste. It must be taken to a special local authority differentiated
waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible nega­tive consequences for the environment and health deriving from inap­propriate disposal and enables the constituent materials to be recov­ered to obtain significant savings in energy and resources. As a
reminder of the need to dispose of household appliances separately,
the product is marked with a crossed-out wheeled dustbin.

Dear Customer
Thank you for choosing one of our appliances, carefully designed and built by

our specialist staff and thoroughly tested to satisfy your cooking requirements.
We suggest that you read this Instruction Booklet so that you will understand

fully how to operate your appliance.
Please keep the booklet handy. You may wish to refer to it at a later date.

CDA

3

Contents

Model RC 9000 ..

Page Number

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features and technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Electronic programmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

How to use the hob burners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

How to use the multifunction oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Do’s and do not’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

For the installer

Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Fitting the adjustable feet and levelling the cooker . . . . . . . . . . . . . . . . . .30

Stability bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Provision for ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Gas installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Gas connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Conversion to Natural Gas or to LPG . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Lubrication of the gas taps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Appliance servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

4

Congratulations on your purchase of this CDA cooker which has been carefully
designed and produced to give you many years of satisfactory use.

Before using this appliance it is essential that the following instructions are carefully
read and fully understood.
We would emphasise that the installation section must be fully complied with for your
safety to ensure that you obtain the maximum benefits from your appliance.

Fig. 1

Assembling the
backguard

■ Remove the two spacers

“A” and the screw “B”
from the rear of the cook­top.

■ Assemble the backguard

as shown in figure 1 and
fix it by screwing the cen­tral screw “B” and the
spacers “A”.

A

B

Declaration of CE conformity

✓

This cooker has been designed, constructed and marketed in compliance with:

- Safety requirements of EU Directive "Gas" 90/396/EEC;

- Safety requirements of EU Directive "Low Voltage" 2006/95/EC;

- Protection requirements of EU Directive "EMC" 89/336/EEC;

- Requirements of EU Directive 93/68/EEC.

Introduction

GB

5

Features and technical data

Fig. 2

2

4

5

1

3

Identification label

When you open the oven
door the indentification label
is at the bottom right hand
side.

Gas burners

1. Auxiliary burner (A) 1,00 kW

2. Semi-rapid burner (SR) 1,75 kW

3. Semi-rapid burner (SR) 1,75 kW

4. Rapid burner (R) 3,00 kW

5. Triple-ring burner (TR) 3,50 kW

6

Control panel

Fig. 3

12345 678

9

CONTROL PANEL - Controls description

1. Electronic programmer

2. Multifunction oven switch knob

3. Multifunction oven thermostat knob

4. Front left burner control knob

5. Rear left burner control knob

6. Central burner control knob

7. Rear right burner control knob

8. Front right burner control knob

Pilot lamp:

9. Oven thermostat indicator light

Please note: This appliance incorporates a safety cooling fan which you will hear
operating whenever the oven or grill are in use. The cooling fan may also operate
when the oven is switched off.

A
U
T
O

7

Electronic programmer

A
U
T
O

Fig. 5

Fig. 4

Description of the buttons:

Timer
Cooking time
End of cooking time
Manual position and cancellation

of the inserted cooking pro­gramme

Advancement of the numbers of
all programmes

Turning back of the numbers of all
programmes and changing the
frequency of the audible signal.

Description of the lighted symbols:
AUTO -

flashing

- Programmer in auto­matic position but not pro­grammed

AUTO -

always lighted

- Programmer in
automatic position with pro­gramme inserted.

Automatic cooking taking place
Timer in operation

and AUTO - flashing - Programme
error.

(The time of day lies between the
calculated cooking start and end
time).

Note: Select a function by the respec­tive button and, in 5 seconds, set the
required time with the

/ buttons

(“one-hand” operation).
A power cut zeroes the clock and can­cels the set programmes.

The electronic programmer is a device that groups together the following functions:
– 24 hour clock with illuminated display
– Timer (up to 23 hours and 59 minutes)
– Programme for automatic oven cooking
– Programme for semi-automatic oven cooking.

8

Fig. 6

A
U
T
O

Fig. 7

Electronic clock (fig. 5)

The programmer is equipped with an
electronic clock with lighted numbers
which indicate hours and minutes.
Upon immediate connection of the
oven or after a blackout, three zeroes
will flash on the programmer panel.
To set the hour it is necessary to push
the button and then the or
button until you have set the exact
hour (fig. 5).
Alternatively, simultaneously push the

two buttons and at the same
time push the or button.
Note: Setting the clock deletes any pro­gramme.

Electronic timer

The timer programme consists only of a
buzzer which may be set for a maxi­mum period of 23 hours and 59 min­utes.
If the AUTO is flashing push the
button.
To set the time, push the button
and the or until you obtain the
desired time (fig. 7).
Having finished the setting, the normal
time will appear on the panel and the

symbol will appear.
The countdown will start immediately
and may be seen at any moment on
the panel by simply pressing the button

.

At the end of the time, the symbol
will be switched off and an intermittent
buzzer will go off; this can be stopped
by pressing any one of the buttons.

Altering the audible
signal

By pressing the button you can
choose from three variations.

Normal cooking without
the use of the
programmer

To manually use the oven, that is, without
the aid of the programmer, it is necessary
to cancel the flashing AUTO by pushing
the button (AUTO will be switched off
and the symbol will go on - Fig. 6).

Attention: If the AUTO is not flashing
(which means a cooking programme has
already been inserted), by pushing the
button you have cancelled the pro­gramme and switched to manual.

9

A
U
T
O

A
U
T
O

Fig. 9

Fig. 8

Automatic oven
cooking

To cook food automatically in the oven,
it is necessary to:

1.Set the length of the cooking time

2.Set the end of the cooking time

3.Set the temperature and the oven
cooking programme.

These operations are done in the fol­lowing way:

1. Set the length of the cooking time by
pushing the button and the
button to

advance, or to go back
if you have passed the desired time
(fig. 8). The AUTO and the sym-
bol will be on.

2.Set the end of the cooking time by
pressing the button (the cooking
time already added to the clock time
will appear), and the button (fig.

9); if you pass the desired time you
may get back by pushing the but­ton.
After this setting, the symbol will
go off. If after this setting, the AUTO
flashes on the panel and a buzzer
goes off, it means there was an error
in the programming.
In this case, modify the end of cook­ing time or the cooking time itself by
following the above instructions
again.

3.Set the temperature and the cooking
programme by using the switch and
thermostat knobs of the oven (see
specific chapters).

Now the oven is programmed and
everything will work automatically, that
is the oven will turn on at the right
moment to end the cooking at the
established time.
During cooking, the symbol remains
on.
By pushing the button you can see
the time that remains until the end of
cooking.

The cooking programme may be can­celled in any moment by pushing .

At the end of the cooking time the
oven will turn off automatically, the
symbol will turn off, AUTO will flash

and a buzzer will sound, which can be
turned off by pushing any of the but­tons.

Turn the switch and thermostat knobs
to zero and put the programmer onto
“manual” by pressing the button.

Attention: A power cut makes the
clock go to zero and cancels the set
programmes.
After a power cut three zeroes will flash
on the panel.

10

A
U
T
O

A
U
T
O

Fig. 10

Fig. 11

Semi-automatic cooking

This is used to automatically switch off
the oven after the desired cooking time
has elapsed.
There are two ways to set your oven:

1. Set the length of the cooking time by
pushing the button and the
button to advance, or to go
backwards if you have passed the
desired time (Fig. 10).

or

2. Set the end of the cooking time by
pushing the button and the
button to advance, or to go
backwards if you have passed the
desired time (Fig. 11).
AUTO and the symbol will be on.
Then set the temperature and the
cooking programme using the oven
switch and thermostat knobs (see
specific chapters).
The oven is switched on and it will
be switched off automatically at the
end of the desired time.
During cooking, the symbol
remains on and by pressing the but­ton you can see the time that
remains till the end of the cooking.
The cooking programme can be can­celled at any moment by pushing the

button.

At the end of cooking, the oven and
the symbol will turn off, the AUTO
will flash and a buzzer will sound; that
can be stopped by pushing any of the
buttons.
Turn the switch and thermostat knobs
to zero and put the programmer onto
“manual” by pressing the button.

11

How to use the hob burners

Lighting of the hob burners

To ignite the burner, the following instructions are to be followed:

1) Lightly press and turn the knob anti-clockwise, and position the knob indicator to the
symbol printed on the control panel (fig. 12).

2) Press the knob to operate the electric ignition; or, in the case of a mains failure light
the burner with a match or lighted taper.

3) Adjust the burner according to the setting required.

Fig. 12

Electric ignition

The sparks generated by the electrodes close to the burners will ignite the choosen
burner. Whenever the lighting of the burners is difficult due to peculiar conditions of
the gas features or supply, it is advised to repeat the ignition with the knob on “mini­mum” position.

Hob burners

Each hob burner is controlled by a sep­arate gas tap operated by a control
knob (fig. 12) which has 3 positions
marked on the control panel, these are:

– Symbol ● : tap closed (burner off)

– Symbol : High (maximum)

– Symbol : Low (minimum)
Push in and turn the knob anti-clock-

wise to the selected position.

To turn the burner off, fully rotate the knob clockwise to the off position: ●.
The maximum setting of the control tap is for boiling, the minimum setting is for slow

cooking and simmering.
All working positions must be choosen between the maximum and minimum setting,

never between the maximum setting and the “OFF” position.

12

Fig. 13

Choice of burner

The burner must be choosen according to the diameter of the pans and energy
required.

Saucepans with handles which are excessively heavy, in relationship to the weight of
the pan, are safer as they are less likely to tip. Pans which are positioned centrally on
burners are more stable than those which are offset.
It is far safer to position the pan handles in such a way that they cannot be accidentally
knocked.
When deep fat frying fill the pan only one third full of oil.
DO NOT cover the pan with a lid and DO NOT leave the pan unattended.
In the unfortunate event of a fire, leave the pan where it is and turn off all controls.
Place a damp cloth or correct fitting lid over the pan to smother the flames.
DO NOT use water on the fire.
Leave the pan to cool for at least 30 minutes.

Fig. 14a

WRONG

Fig. 14b

CORRECT

Correct use of triple-ring burner

The flat-bottomed pans are to be placed directly onto the pan-support.
To use the WOK you need to place the proper stand in order to avoid any faulty
operation of the triple-ring burner (Fig. 14a - 14b).

IMPORTANT:

The wok pan stand (fig. 14b) MUST BE PLACED ONLY over the pan-rest for the triple­ring burner.

Burners Pan diameter

Auxiliary 12 ÷ 14 cm
Semi-rapid 16 ÷ 24 cm
Rapid 24 ÷ 26 cm
Triple-ring 26 ÷ 28 cm
Wok max 36 cm

do not use pans with concave or convex bases

13

How to use the Multifunction oven

Operating principles

Heating and cooking in the MULTI-FUNCTION oven are obtained in the following
ways:
a. by normal convection

The heat is produced by the upper and lower heating elements.

b. by forced convection

A fan sucks in the air contained in the oven muffle, which sends it through the circu­lar heating element and then sends it back through the muffle. Before the hot air is
sucked back again by the fan to repeat the described cycle, it envelops the food in
the oven, provoking a complete and rapid cooking.
It is possible to cook several dishes simultaneously.

c. by semi-forced convection

The heat produced by the upper and lower heating elements is distributed through­out the oven by the fan.

d. by radiation

The heat is radiated by the infra red grill element.

e. by radiation and ventilation

The irradiated heat from the infra red grill element is distributed throughout the oven
by the fan.

f. by ventilation

The food is defrosted by using the fan only function without heat.

General features

As its name indicates, this is an oven that presents particular features from an opera­tional point of view.

In fact, it is possible to insert 7 different programmes to satisfy every cooking need.
The 7 positions, thermostatically controlled, are obtained by 4 heating elements which
are:

– Bottom element 1725 W
– Top element 1725 W
– Grill element 2500 W
– Circular element 2500 W

Note:

Upon first use, it is advisable to operate the oven for 30 minutes in the position and for
another 30 minutes at the maximum temperature (thermostat knob on position 250) in the
positions

and

, to eliminate possible traces of grease on the heating elements.

Clean the oven and accessories with warm water and washing-up liquid.

ATTENTION - MOST IMPORTANT
Pay special attention not to touch
the hot heating element inside the
oven cavity.

WARNING:
The door is hot, use the handle.

14

Fig. 15

Fig. 16

Traditional convection cooking

The upper and lower heating elements come on. The heat is dispersed by natural con­vection and the temperature must be set to between 50° and 250°C via the thermo­stat knob.
The oven must be preheated before cooking.

Recommended for:
Food that requires the same degree of cooking both inside and out, for example
roasts, spare pork ribs, meringues etc.

Oven light

By setting the knob to this position, only the oven light comes on.
It remains on in all the cooking modes.

Function selector knob

(Fig. 15)

Rotate the knob clockwise to set the oven for one of the following functions.

Thermostat knob

(Fig. 16)

This only sets the cooking temperature and does not switch the oven on.
Rotate clockwise until the required temperature is reached (from 50 to 250°C).
The light between the thermostat and the function selector will illuminate when the
oven is switched on and turns off when the oven reaches the correct temperature.
The light will cycle on and off during cooking in line with the oven temperature.