CATEYE USBCU, CY300 User Manual

Page 1

Page 2

ENG-1

Continue

Thank you for purchasing the CATEYE Q3a Multi-Sport Computer. The Q3a is a wristwatch heart rate monitor with additional cyclocomputer features to allow athletes to extensively organize and analyze their training data.

2.4 GHz-frequency digital wireless technology, the same technology used for everyday equipment such as wireless network is used for both the integrated cadence/speed sensor and the heart rate sensor. This technology practically eliminates all interference from external noise and cross-talk with other wireless users, providing you with stress-free riding. Read this instruction manual thoroughly and understand the functions of the wristwatch before using it. Keep this manual in a safe place for future reference.

Important

Always follow the instructions that are marked with “UÊ

Warning!!!”.

No part of this manual may be reproduced or transmitted without the prior written UÊ

permission of CatEye Co., Ltd.

The contents and illustrations in this manual are subject to change without notice.UÊ

If you have any questions or concerns about this manual, please contact CatEye UÊ

at www.cateye.com.

Introduction

Page 3

ENG-2

Before use

See this section for installation of the unit on the bicycle, use of the heart rate sensor, wristwatch set-up, and the basic operation of the product.

Bicycle InstallationUÊ..........................................See page 10-12

Heart rate sensorUÊ.............................................See page 13

Wristwatch set-upUÊ...........................................See page 14-21

Basic wristwatch operationUÊ.............................See page 22-23

Clock mode (CLOCK)

See this section to learn how to operate the Clock mode functions.

Alarm clockUÊ.....................................................See page 24

Sports mode (SPORTS)

See this section to learn how to operate the wristwatch functions.

Display data in Sports modeUÊ...........................See page 28-29

Option mode (OPTION)

See this section to learn how to operate the training functions frequently used in Sports mode (countdown and interval functions), and how to set the HR target zone.

Training functionsUÊ...........................................See page 32-35

Setting the target heart rate zonesUÊ..................See page 37-38

Data mode (DATA)

See this section to review and manage the recorded ﬁles.

Recorded data review (File view)UÊ.....................See page 40-45 “File view”

Download recorded data to PC (PC link)UÊ.........See page 45-47 “PC link”

Setup mode (SETUP)

See this section to change the wristwatch conﬁguration.

Changing the wristwatch conﬁgurationUÊ...........See page 49-60

About the CD-ROM supplied

The CD-ROM supplied contains the following information.

Quick start manual UÊ(PDF ﬁle)

Installing the unit on the bicycle and setting up the wristwatch are described using video.

Download software “e-Train Data™UÊ (Windows version)”

This software is used to transfer the measurement data to your personal computer, and then use various functions on the PC, such as a graph display (The optional “USB communication kit” is required).

Instruction manual UÊ(PDF ﬁle)

This manual can be viewed in PDF ﬁle (7 languages).

Use the CD-ROM in combination with this manual.

About the manuals

Page 4

ENG-3

Continue

Introduction.........................1

About the manuals.................2

Proper use of the CatEye Q3a....5

Important............................6

Description of wristwatch and

its parts..............................8

Wristwatch.................................8

Accessories................................8

Screen display .....................9

Bicycle Installation ..............10

Mount the speed sensor and

magnet.....................................10

Install the wristwatch onto

the handlebar...........................12

Heart rate sensor ................ 13

Before wearing the heart rate

sensor......................................13

Wearing the heart rate sensor

...13

Preparing the wristwatch ....... 14

Removing the insulation sheet

...14

Restarting ................................14

Setting the clock/date ..............15

Switching to the Setup mode... 16

Tire circumference input..........16

Selecting measurement unit ....18

Switching to the Sports mode

...18

Operation test ..........................19

Formatting/Restarting

operation..................................21

Basic operation of the

wristwatch ........................ 22

Switching between modes .......22

Backlight..................................23

Power-saving mode.................23

Transmission sleep mode........23

Saving the power of the

wristwatch ...............................23

Clock mode (CLOCK) ............24

Functions in Clock mode..........24

Display data in Clock mode......24

Alarm clock mode....................24

Sports mode (SPORTS) .........25

Function in Sports mode..........25

Upper and middle display data

...25

Lower display data................... 26

Starting/Stopping

measurement........................... 26

Resetting the measurement

data and saving the ﬁles ..........27

Display data in Sports mode....28

Pace function...........................30

Lap function.............................30

Training function......................32

Target heart rate zone ..............35

Option mode (OPTION).......... 36

Function in Option mode..........36

Setting the training function.....36

Setting the target heart rate

zones .......................................37

Data mode (DATA)............... 39

Function in Data mode.............39

File view...................................40

PC link .....................................45

Past records.............................47

Setup mode (SETUP) ............ 49

Function in Setup mode...........49

Setting the clock/date ..............50

Setting the alarm clock ............51

Setting the tire circumference

...52

Contents

Page 5

ENG-4

Searching for sensor ID...........53

Setting the measurement unit

...55

Setting the record interval........56

Total trip distance/total

elapsed time entry....................57

Setting the auto-mode .............58

Setting sound...........................59

Correcting the sea level altitude

...60

Basic knowledge of the

altitude measurement........... 61

Altitude measurement function

...61 Relation between the altitude

and atmospheric pressure .......62

Knowledge related to weather

and altitude ..............................62

Heart rate training ............... 63

Target heart rate zone ..............63

Training for competition ..........66

Use of the target zone..............67

Trouble shooting ................. 68

Trouble on display ...................68

Trouble on operation................70

Water resistance of the

wristwatch ........................ 71

Before aquatic and outdoor

activities...................................71

Replacing battery ................ 71

Wristwatch...............................72

Heart rate sensor .....................72

Speed sensor...........................72

Maintenance...................... 73

Spare accessories ...............73

Flow of the screen ...............74

Speciﬁcations .................... 76

Registration....................... 78

Limited warranty................. 78

Index............................... 79

Page 6

ENG-5

Continue

Proper use of the CatEye Q3a

Please follow the following instructions for safe usage.

The meaning of icons in this manual:

Warning!!!: Sections marked with these icons are critical for safe use of the

device. Be sure to follow these instructions.

Caution:

Important cautionary notes on the use and operation of the Q3a.

Helpful tips are highlighted with asterisks.*

The meaning of color on the screen in this manual:

Red: Indicates the displayed data is ﬂashing. Black/gray: Indicates the displayed data is on.

Warning!!!:

Pace maker users should never use this device.UÊ

Cycling can be a dangerous sport. Always remember to pay attention to the road, UÊ

trafﬁc, and surroundings.

The altitude data of this unit is for reference only. Do not use this unit as an UÊ

instrument for professional purposes.

Do not leave any battery within the reach of children, and dispose of them cor-UÊ

rectly. If a battery is swallowed, consult a doctor immediately.

Caution:

Regularly check the positions of the magnets and the speed/cadence sensors and UÊ

make sure that they are securely mounted. If loose, tighten ﬁrmly to avoid falling and damage.

Avoid leaving the uni t in dire ct sunlig ht for ex tended periods of time. UÊ

A temperature sensor built inside the wristwatch to calculate the altitude may be affected from excessive heat, causing inaccurate display of temperature.

Do not disassemble the wristwatch, heart rate sensor, or speed sensor.UÊ

Do not subject the wristwatch, heart rate sensor, or speed sensor to strong impact; UÊ

take care also to prevent any of them from falling.

Do not use paint thinner or rubbing alcohol to clean the unit. Use a damp cloth and UÊ

use mild detergent if necessary.

Stop using the unit if you have skin irritation with the HR strap or electrode pad.UÊ

Do not twist or pull strongly the heart rate sensor.UÊ

The heart rate sensor may deteriorate due to long-term use. Replace the heart rate UÊ

sensor if it has frequent measurement errors.

As a nature of liquid crystal displays, sunglasses with polarized lens may block the UÊ

visibility.

Page 7

ENG-6

2.4 GHz digital wireless system

2.4 GHz-frequency digital wireless technology, which is the same technology used for wireless LAN, is used for both the integrated speed/cadence sensor and the heart rate sensor. This technology practically eliminates interference from external noise and cross-talk with other wireless computer users, and enables you to store highly reliable data. However, in a very rare occasions, objects and places may generate strong electromagnetic waves and interference, which may result in incorrect measurement. The following are potential sources of interference:

Should be especially careful while synchronizing the sensor ID.*

TV, PC, radios, motors/engines, or in cars and trains.UÊ

Railroad crossings and near railway tracks, around television transmitting stations UÊ

and radar bases.

Other wireless computers or digitally controlled lights.UÊ

Altitude measurement

The altitude is determined by detecting the change in atmospheric pressure using a pressure sensor built in the wristwatch, which is then converted into elevation. For this reason, the measurements may change even at the same location depending on the change in atmospheric pressure caused by weather conditions. In addition, note that there is a change of about 30 to 40 m during the early morning through the evening even in stable weather. This unit may indicate incorrect measurements in the following locations and/or environments.

When the atmospheric pressure and/or temperature change(s) signiﬁcantly due to UÊ

rapid weather change.

In a location where pressure is controlled, such as in an airplane.UÊ

The altitude measurement may change temporarily when the temperature changes UÊ

suddenly, such as in cases of going outside from an indoor room. It will return to the normal value after a while.

Important

Page 8

ENG-7

Continue

Automatic recognition of the speed sensor ID

The speed sensor has its own ID, and the wristwatch measures in synchronization with the ID. Two speed sensor IDs can be registered to one wristwatch, which can automatically identify the 2 speed sensors once their IDs are registered in advance. As a tire circumference is set to the speed sensor ID, wheel selection by manual operation is no longer required, which was necessary with conventional units.

The speed sensor currently recognized is indicated with a sensor icon (*

or )

on the screen.

Procedure of automatic recognition

When the wristwatch changes to the Clock mode by its power-saving function, and then returns to the Sports mode, automatic recognition of the speed sensor ID is performed through the following procedure.

The wristwatch searches a sensor signal from the speed sensor ID-1.

When the wristwatch receives a sensor signal from ID-1, it displays sensor icon

on the screen, and starts measurement. When the wristwatch cannot receive any sensor signal from ID-1, it searches a sensor signal from ID-2.

When the wristwatch receives a sensor signal from ID-2, it displays sensor icon

on the screen, and starts measurement. When the wristwatch cannot receive any sensor signal from ID-2, it searches a sensor signal from ID-1 again.

The wristwatch repeats synchronization through the procedure described above even if it fails in synchronization for some reason, such as communication failure; in such cases however, it takes time for recognition.

When the wristwatch cannot receive any signal from the speed sensor in 5 * minutes, the power-saving mode is activated, and the wristwatch changes to the Clock mode.

Switching the ID by manual operation

The speed sensor ID can be forcibly switched by manual operation from “Setting the tire circumference” in the Setup mode. Use this operation in the following cases.

When the wristwatch cannot recognize the intended sensor signal, since the 2 UÊ

registered speed sensors are nearby and both are sending a sensor signal.

When you want to switch the speed sensor ID immediately.UÊ

Once you switch the speed sensor ID by manual operation, the wristwatch * continues to search only the speed sensor ID you switched when returning to the Sports mode. When the wristwatch cannot receive any sensor signal in 5 minutes, the power-saving mode is activated, and the wristwatch changes to the Clock mode. The wristwatch searches through the procedure of automatic recognition when it returns to the Sports mode.

Page 9

ENG-8

Wristwatch

Description of wristwatch and its parts

Accessories

Bracket

(for handlebar-mount)

Speed sensor

(SPEED/CADENCE)

Heart rate sensor

HR strap

Wheel magnet

Cadence magnet

Nylon ties (x7)

CD-ROM

Menu/enter button

(MENU)

Start/stop/ select button (SSS)

Mode-1/+ button *

(MODE1)

Mode-2/- button *

(MODE2)

Pressure sensor

Battery cover

Serial number

Belt

Lap button (LAP)

Pressing and holding the * MODE1 or MODE2 button lights up the backlight (Except in Setup mode).

See page 2 for the CD-ROM contents.*

This manual

Page 10

ENG-9

Continue

Screen display

Icon Description



Sensor icon

Displays the speed sensor currently synchronized.

km/h mph

Speed unit

Flashes while the measurement (counting the elapsed time).

ft m

Altitude unit

Flashes while the measurement (counting the elapsed time).

Alarm clock

Lights up when the alarm clock is on.

Speed/Cadence sensor signal

Indicate Speed/Cadence sensor signal status. (page 23)

Heart rate sensor signal

Indicate Heart rate sensor signal status. (page 23)

Target zone

Lights up when the target zone is on, and ﬂashes when it is out of the zone.

Low battery alarm

Flashes when the battery of the wristwatch needs replacing with a new one.

bpm

Heart rate unit

AM PM

AM/PM display (lights up when using the 12-hour system)

LAP

Lap indicator

Lights up while the lap data is displayed.

Auto-mode

Lights up when the auto-mode function is on.

Slope angle, zone, memory point utilization Alarm

Lights up when the HR alarm sound feature is turned on.

SSS

MODE1

MODE2

Button navigation

Indicates the buttons available while setting up the wristwatch, or on the Setup screen.

Speed pace arrow (upper display)

The pace arrows show whether the current speed is faster (

) or slower ( ) than the average speed.

Heart rate pace arrow (middle display)

The pace arrows show whether the current heart rate is faster (

) or slower ( ) than the average heart rate.

Upper data display

Lower data display

Upper selected mode icon

Indicates the measurement data currently displayed in the upper data display.

Lower selected mode icon/unit

Indicates the unit along with the data currently displayed in the lower data display.

Page 11

ENG-10

Before use

Bicycle Installation

Mount the speed sensor and magnet

1-1.Lightly secure the speed sensor

Locate the speed sensor on the left (non-drive side) chain stay as shown above, and loosely secure it with the nylon ties.

Do not tighten the nylon ties completely at * this stage. Once a nylon tie is tightened, it cannot be pulled out.

1-2.Mount the magnet

Loosen the set scre ws both on the

SPEED side and CADENCE side of the

speed sensor, and turn the sensor to the angle as shown on the right.

Temporarily secure the wheel magnet to

the spoke so that it faces the sensor zone on the SPEED side.

Temporarily secure the cadence magnet in-

side the crank with nylon ties, so that it faces the sensor zone on the CADENCE side.

Two magnets maybe stuck together inside * the package, and appear as one magnet.

฀

SPEED

CADENCE

SPEED

฀

SPEED

CADENCE

Wheel magnet

Cadence magnet

Speed sensor

Nylon ties

Speed sensor

Left chain stay

1. Pre-Install the

wheel magnet

Pre-install the cadence magnet

Nylon ties

2. Set screw on the SPEED side

3. Set screw on the CADENCE side

Sensor zone

Page 12

ENG-11

Before use

Continue

When the speed sensor is not positioned properly in respect to the two * magnets (in both Steps 2 and 3), move the speed sensor back and forth so that it is positioned properly. After you move the speed sensor, adjust the position so that the two magnets face the relevant sensor zone.

After adjustment, tighten the nylon ties ﬁrmly to secure the speed sensor.

1-3.Adjust the distance to the magnet

Adjust the distance between the wheel

magnet and the SPEED side of the speed sensor to be about 3 mm. After adjustment, tighten the set screw on the SPEED side.

Adjust the distance between the cadence

magnet and the CADENCE side of the speed sensor to be about 3 mm. After adjustment, tighten the set screw on the CADENCE side.

For steel axle pedals, the cadence magnet can * be installed onto the end face of the pedal axle. Make sure to remove the double-sided tape from the magnet when doing this.

1-4.Securing various parts

Tighten the speed sensor, set screw, and magnet ﬁrmly, and check for any looseness.

Speed/Cadence sensor nylon ties Speed and Cadence sensor screws Wheel magnet screw Cadence magnet

Wheel

magnet

Cadence magnet

SPEED

CADENCE

About 3 mm

Cut extra length of the nylon tie with scissors.

Page 13





ENG-12

Before use

Install the wristwatch onto the handlebar

Install the wristwatch to the handlebar with a bracket.

Check the correct direction of the bracket, and attach it to the handlebar.

Attach the bracket in the correct direction according to the handlebar size, and ﬁx it using nylon ties.

Wrap the wristwatch around the bracket.

Firmly fasten the belt so that the wristwatch will not come off.

Cut extra length of the nylon tie with scissors.

Put the nylon ties through the bracket * before you attach it to the handlebar.

Standard handlebar

Oversize bar

Nylon ties

Handlebar

Bracket

Wristwatch

BeltHandlebar

Front

Page 14

ENG-13

Before use

Continue

Heart rate is measured when the heart rate sensor is worn on the chest.

Before wearing the heart rate sensor

Warning!!!:

This product must NOT be used by those who have a pacemaker.

To avoid measurement errors, it is recommended to moisten the electrode pads UÊ

with water.

If your skin is ultra-sensitive, the electrode pad may be moistened with water and UÊ

worn over a thin undershirt.

Chest hair may interfere with the measurement.UÊ

Wearing the heart rate sensor

Insert the HR strap hook to the hole on the heart rate sensor until it clicks.

Wear the heart rate sensor with the HR strap, and adjust the length of the HR strap

to ﬁt your chest size (under bust). Fastening the strap too tightly may cause discomfort.

Insert the HR strap hook to the other hole on the heart rate sensor

until it clicks.

For removal, hold near the hole on the heart rate sensor and the hook, and twist off.

Ensure that the rubber part of the electrode pad is in direct contact with the body.* Wearing the heart rate sensor when your skin is dry or on top of your undershirt may produce *

measurement errors. To avoid errors, moisten the rubber part of the electrode pad.

Heart rate sensor

Electrode pad

Hook

Heart rate sensor

HR strap

Page 15

ENG-14

Before use

Wristwatch's basic items must be set up before using it.

Removing the insulation sheet

When you use the unit for the ﬁrst time after purchasing, remove the insulation sheet under the battery.

Open the battery cover of the wristwatch

using a coin, etc.

Turn the inner cover to the open position

using a coin, remove this, and remove the insulation sheet under the battery.

Do not turn the inner cover excessively. * Otherwise, the tab may be damaged.

Replace the battery, and turn the inner

cover to the closed position. Check that the cut-out portion of the inner cover faces the pin, and the 2 tabs are ﬁxed.

Press the AC button beside the inner

cover using a tool with a pointed tip.

Check that an o-ring is installed to the

groove on the wristwatch, and firmly close the battery cover.

Preparing the wristwatch

Restarting

When using the unit for the ﬁrst time after purchasing, or after replacing batteries, restart the wristwatch to make it work properly.

The wristwatch and each sensor ID have been checked at the factory.*

Simultaneously press and hold the

MENU, SSS, MODE1, and MODE2 buttons

on the wristwatch for about 4 seconds. “FACTORY DEFAULT” is displayed.

MODE2

MODE1

SSS

(Simultaneously press)

When “* FACTORY DEFAULT” is not displayed on the screen, the button operation has not been completed properly. Simultaneously press and hold the 4 buttons again until the display changes.

Select “NO”. When “NO” is displayed on the screen, conﬁrm with the SSS button. The backlight of the display lights up and a buzzer sounds, then the display is switched to the clock/date setting screen. Proceed to the next set-up item, “Setting the clock/date”.

YES NO :

MODE2

MODE1

(or)

Conﬁrm :

SSS

O-ring

AC button

Battery cover

Inner cover

Tab

Cut-out portion

CR2430

Open position

Closed position

Insulation sheet

Open

Restarting

Page 16

ENG-15

Before use

Continue

* Select “YES” by pressing the MODE1 or MODE2 button for

the formatting operation. As the formatting operation deletes all data, select “NO” for the restarting operation. See “Formatting/Restarting operation” on page 21 for differences between the formatting and restarting operations.

The restarting operation will be cancelled if no button has ben * pushed for 3 minutes and the wristwatch will enter the Clock screen automatically. In this case, press the 4 buttons simultaneously and do the restart operation again.

Setting the clock/date

Set the current time and date.

Press and hold the * MODE1 or MODE2 button to increase/decrease the number quickly.

Select the clock display format. Select “24h (24 hour)” or “12h (12 hour)” pressing the MODE1 or MODE2 buttons, and conﬁrm with the SSS button.

24h 12h :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Enter the “Hour” and “Minute”. Enter the “Hour” pressing the MODE1 to increase, and MODE2 button to decrease the ﬂashing value, conﬁrm with the SSS button, and then enter the “Minute” in the same way.

Edit value :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select the date display format. Select the date display format from YY.MM.DD (Year/ Month/Day), DD.MM.YY (Day/Month/Year) , and

MM.DD.YY (Month/Day/Year) pressing the MODE1 or MODE2 buttons, and conﬁrm with the SSS button.

Switch the display :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Enter the “Year”, “Month” and “Day”. Enter the “Year”, “Month” and “Day” in the display order selected in Step 3 using the MODE1 to increase, and MODE2 button to decrease the ﬂashing value, and conﬁrm with the SSS button. For “Year”, enter the last 2 digits of the year.

Edit value :

MODE2

MODE1

(or)

Conﬁrm :

SSS

After you set the clock/date, press the 5.MENU button to complete the restarting operation, and switch to the Clock mode.

To Clock mode (setup is completed):

Display format

Formatting

YY/MM/DD

Display format

Hour

Minute

Page 17

ENG-16

Before use

Switching to the Setup mode

Switch the wristwatch from the Clock mode to the Setup mode, and set the tire circumference and the measurement unit.

Press and hold the MENU button in the Clock mode to display “SETUP MENU” on the screen. It switches to “CLOCK DATE” automatically.

Switch modes:

(press & hold)

Unless you perform an operation in the Setup mode within 3 minutes, it * returns to the Clock mode. In such cases, any change is not reﬂected.

Tire circumference input

In the Setup mode “Setting the tire circumference”, enter the tire circumference of the bicycle to

(Sensor 1) in millimeters.

See “Tire circumference” on the next page for reference.* Press and hold the * MODE1 or MODE2 button to increase/decrease the number quickly.

Press the MODE1 button twice to switch to “TIRE”, and conﬁrm with the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

When and “S/ID:1” are ﬂashing, conﬁrm with the SSS button. Change the tire circumference of Sensor 1.



MODE2

MODE1

(or)

Conﬁrm :

SSS

Enter the last 2 digits of the tire circumference by pressing the MODE1 or MODE2 button, and move digits by pressing the SSS button. Then enter the ﬁrst 2 digits in the same way.

Increase/decrease:

MODE2

MODE1

(or)

Move digits:

SSS

Pressing the 4.MENU button conﬁrms the tire circumference, and returns to the Setup mode “TIRE”.

Setup is completed:

To use * (Sensor 2), set the tire circumference of Sensor 2 according to the Setup mode “Searching for sensor ID” on page 53, after you complete “Preparing the wristwatch”.

Page 18

ENG-17

Before use

Continue

Tire circumference

You can ﬁnd the tire circumference (L) of your tire size in the tire circumference reference table below, or actually measure the tire circumference (L) of your bicycle.

How to measure the tire circumference (L)

For the most accurate measurement, do a wheel roll out. With the tires under proper pressure, place the valve stem at the bottom. Mark the spot on the ﬂoor and with the rider's weight on the bike, roll exactly one wheel revolution in a straight line (until the valve comes around again to the bottom). Mark where the valve stem is and measure the distance on the ground in millimeters.

For your reference, use the tire circumference table below.*

Tire circumference reference table

L mm

ETRTO

Tire size

(mm)

47-203 12 x 1.75 935 54-203 12 x 1.95 940 40-254 14 x 1.50 1020 47-254 14 x 1.75 1055 40-305 16 x 1.50 1185 47-305 16 x 1.75 1195 54-305 16 x 2.00 1245 28-349 16 x 1-1/8 1290 37-349 16 x 1-3/8 1300

32-369

17 x 1-1/4(369)

1340

40-355 18 x 1.50 1340 47-355 18 x 1.75 1350 32-406 20 x 1.25 1450 35-406 20 x 1.35 1460 40-406 20 x 1.50 1490 47-406 20 x 1.75 1515 50-406 20 x 1.95 1565 28-451 20 x 1-1/8 1545 37-451 20 x 1-3/8 1615 37-501 22 x 1-3/8 1770 40-501 22 x 1-1/2 1785 47-507 24 x 1.75 1890 50-507 24 x 2.00 1925 54-507 24 x 2.125 1965 25-520 24 x 1(520) 1753

24 x 3/4 Tubular

1785

28-540 24 x 1-1/8 1795 32-540 24 x 1-1/4 1905 25-559 26 x 1(559) 1913

ETRTO

Tire size

(mm)

32-559 26 x 1.25 1950 37-559 26 x 1.40 2005 40-559 26 x 1.50 2010 47-559 26 x 1.75 2023

50-559 26 x 1.95 2050

54-559 26 x 2.10 2068 57-559 26 x 2.125 2070 58-559 26 x 2.35 2083 75-559 26 x 3.00 2170 28-590 26 x 1-1/8 1970 37-590 26 x 1-3/8 2068 37-584 26 x 1-1/2 2100

650C Tubular 26 x 7/8

1920

20-571 650 x 20C 1938 23-571 650 x 23C 1944

25-571

650 x 25C 26 x 1(571)

1952

40-590 650 x 38A 2125 40-584 650 x 38B 2105 25-630 27 x 1(630) 2145 28-630 27 x 1-1/8 2155 32-630 27 x 1-1/4 2161 37-630 27 x 1-3/8 2169 18-622 700 x 18C 2070 19-622 700 x 19C 2080 20-622 700 x 20C 2086

23-622 700 x 23C 2096

25-622 700 x 25C 2105 28-622 700 x 28C 2136

ETRTO

Tire size

(mm)

30-622 700 x 30C 2146 32-622 700 x 32C 2155

700C Tubular

2130

35-622 700 x 35C 2168 38-622 700 x 38C 2180 40-622 700 x 40C 2200 42-622 700 x 42C 2224 44-622 700 x 44C 2235 45-622 700 x 45C 2242 47-622 700 x 47C 2268 54-622 29 x 2.1 2288 60-622 29 x 2.3 2326

Page 19

ENG-18

Before use

Selecting measurement unit

Select the speed unit and temperature unit.

Press the MODE1 button twice to switch to “UNITS”, and conﬁrm with the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select the speed unit by pressing the MODE1 or MODE2 button, and conﬁrm with the SSS button.

km/h mph :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select the temperature unit by pressing the MODE1 or MODE2 button in the same way.

°C °F :

MODE2

MODE1

(or)

Pressing the 4.MENU button conﬁrms the measurement unit, and returns to the Setup mode “UNITS”. Now, the wristwatch setup is completed. Press the MENU button again to switch to the Clock mode screen.

To the mode top/switch the mode :

Switching to the Sports mode

Switch the wristwatch from the Clock mode to the Sports mode for the operation test of the speed sensor and heart rate sensor.

Press the MENU button in the Clock mode to display “SPORTS MENU” on the screen. It switches to the measurement screen automatically.

Switch modes:

Speed unit

Temperature unit

Page 20

ENG-19

Before use

Continue

Operation test

It may take up to approximately 2 minutes to display the screen because the * wristwatch checks the sensor when switching to Sports mode. If the signal icon *

or on the measurement screen is turned off, press the

MODE1 or MODE2 button to turn it on.

Speed sensor (SPEED side)

Raise the rear wheel and spin the wheel.

When the speed is displayed on the screen, it is operating normally.

Speed sensor (CADENCE side)

Turn the crank.

When the cadence is displayed on the screen, it is operating normally.

Heart rate sensor

Wear the heart rate sensor (page 13).

When the heart rate is displayed on the screen, it is operating normally.

*Heart rate sensor can also be activated by rubbing both electrode pads with

thumbs. This method cannot be used to measure the heart rate accurately, but is used as a simple method for testing the sensor/wristwatch communication and searching for the sensor ID.

Electrode pad

Page 21

ENG-20

Before use

Important: When the speed, cadence, and/or heart rate are/is not displayed, possible

causes are as follows.

Speed and cadence are not displayed.

Check items Remedy

Is the Speed and Cadence sensor icon on

icon is off, the wristwatch cannot receive any data. Press the

MODE1 or MODE2 button to cancel the transmission sleep mode (page 23).

Check whether the distance between the speed/cadence sensor and the magnet is too large.

Adjust the position of the speed/cadence sensor and that of the magnet correctly. (See “Bicycle Installation” on page 10.)

Is the sensor zone of the speed/cadence sensor aligned the center of the magnet?

Has the power-saving mode been activated, entering Clock mode?

Press the MENU button to switch to Sports mode.

The display may be delayed depending on the wireless transmission condition.

Check whether any speed signal is received by spinning the wheel for a while.

Have you performed the formatting operation?

The sensor ID synchronized at the factory is initialized by formatting. Synchronize the speed sensor ID, according to the Setup mode “Searching for sensor ID” (page 53).

Heart rate is not displayed.

Check items Remedy

Is the Heart rate sensor icon on ? If icon is off, the wristwatch cannot receive any data. Press

the MODE1 or MODE2 button to cancel the transmission sleep mode (page 23).

Has the power-saving mode been activated, entering Clock mode?

Press the MENU button to switch to Sports mode.

Is the heart rate sensor attached securely to your body?

Adjust the electrode pad with its rubber surface to have good contact with the body.

Dry skin (particularly in winter) Slightly moisten the electrode pad of the heart rate sensor.

Is the Heart rate sensor being worn correctly?

To wear the electrode pad correctly, follow the instructions for wearing the heart rate sensor (page 13).

Have you performed the formatting operation?

The sensor ID synchronized at the factory is initialized by formatting. Synchronize the hear t rate sensor ID, accordi ng to the Setup mode “Searching for sensor ID” (page 53).

Page 22

ENG-21

Before use

Continue

Formatting/Restarting operation

There are 2 different wristwatch set-up operations; formatting and restarting operations. Follow the appropriate one depending on the situation.

Formatting :

When you want to delete all data and the setup of the wristwatch.

Restarting : When you use the unit for the ﬁrst time after purchasing, or after replac-

ing batteries, or an error is displayed.

In the restarting operation, the following data are retained.*

SPORTS MENU Date OPTION MENU Setting the target zone

DATA MENU

UÊ->Ûi`ÊwiÊ`>Ì>

UÊ,`iÊ`>Ì>

UÊ}Ê`>Ì>

SETUP MENU

UÊ>ÀÊVVÊÃiÌÌ}

UÊ/ÀiÊVÀVÕviÀiViÊ>`Ê

Sensor currently selected

UÊ-iÃÀÊ

UÊi>ÃÕÀiiÌÊÕÌ

UÊ,iVÀ`ÊÌiÀÛ>

UÊÕÌ`i

UÊ/À>}ÊvÕVÌ

UÊ-Õ`ÊÃiÌÌ}

UÊ-i>ÊiÛiÊ>ÌÌÕ`i

Flows of the formatting and restarting operations

The formatting and restarting procedures are as follows.

In the case of the formatting operation, you can set the “tire circumference” * and “measurement unit” sequentially after you set the “clock/date”. Each set-up procedure is described on the page referenced. After you complete the set-up, be sure to synchronize the sensor ID according to the Setup mode “Searching for sensor ID” (page 53).

For restarting:

The date when last executed the restarting * operation will be initially displayed.

Restarting operation (page 14)

Setting the clock/date (page 15)

Clock mode

For formatting:

Formatting operation (page 14)

Setting the clock/date (page 15)

Selecting measurement unit (page 18)

Tire circumference input (page 16)

Page 23

ENG-22

Before use

Switching between modes

The wristwatch has 4 types of mode functions and the Setup mode. “CLOCK MENU”, “SPORTS MENU”, “OPTION MENU”, and “DATA MENU” are alternatively selected in sequence by pressing the MENU button. Select the screen of your choice to proceed to the mode screen automatically.

Basic operation of the wristwatch

Sports mode (page 25)

This measurement screen is used as a cyclocomputer and/or heart rate monitor.

Option mode (page 36) This mode is used to edit option setup values often used while riding bicycle such as zones, and count down.

Data mode (page 39) This mode is used to check the data saved and/or import them to your PC.

Clock mode (page 24) Displays the clock. This mode is used for everyday wristwatch functions displays also altitude, temperature and alarm.

Press and hold the * MENU button in the Clock mode or Sports mode to switch to “SETUP MENU”.

(press & hold)

To the previous mode screen

Setup mode (page 49) This mode is used to edit values and setup for less frequently used items, such as sound and wheel circumference.

Page 24

ENG-23

Before use

Continue

Backlight

Pressing and holding the MODE1 or MODE2 button illuminates the display for about 3 seconds (Except in the Setup mode).

Pressing any button while backlight is still on extends the illu-* mination for another 3 seconds.

Power-saving mode

Transmission sleep mode

When the wristwatch does not receive any data from the speed sensor or heart rate sensor for 5 minutes, each sensor will enter the transmission sleep status to save battery power. No sensor signal can be received in the transmission sleep status. To restart measuring, press the MODE1 or MODE2 button to recover from transmission sleep. The signal transmission status of each sensor can be checked with the relevant signal icon and the numerical value “---” display.

UÊ (ﬂashing) :

Receiving sensor signal (under operation)

UÊ (constant) :

Stand-by for sensor signal (searching for sensors)

UÊ (off) :

Transmission sleep. Displays the symbol “---”.

Transmission sleep is set separately for the speed sensor * and the heart rate sensor. Accordingly, if the bicycle is stopped for over 5 minutes with the heart rate sensor worn, only the speed sensor goes into transmission sleep. When resuming the ride, speed/cadence sensor must be re-activated in order to display necessary data.

When either the speed sensor or the heart rate sensor is in * transmission sleep, the display remains in the Sports mode; however, when both sensors go into transmission sleep, the wristwatch switches to the power-saving mode.

Saving the power of the wristwatch

When the wristwatch does not receive any data from both the speed and heart rate sensors for 5 minutes, it will switch to Clock mode automatically. Press the MENU button to return to Sports mode and continue measuring. For details, see “Switching between modes” on page 22.

Even if the power-saving mode is activated, data not reset * are saved in the wristwatch.

MODE2

MODE1

(or)

(press & hold)

Speed sensor signal icon

The speed sensor is in transmission sleep. Displays the symbol “---”.

The heart rate sensor is in transmission sleep. Displays the symbol “---”.

Clock mode

Heart rate sensor signal icon

Page 25

ENG-24

Clock mode

Switching to Clock mode

Select “CLOCK MENU” by pressing the MENU button until display swithces to Clock mode.

Clock mode is the default screen, so if the power-saving mode is * activated in any other mode display will switch to Clock mode. For details, see “Power-saving mode” on page 23.

Functions in Clock mode

Displays the current time, date, and day of the week. Press the MODE1 button to display the current sea level altitude. Press the MODE2 button to display the current temperature or turn on/off the alarm clock.

Display data in Clock mode

For setting the time and date, see the Setup mode “Setting the clock/date” (page 50).* Altitude may need to be adjusted to the current location. For details, see “Correcting the sea * level altitude” on page 60, and “Basic knowledge of altitude measurement” on page 61. While the current sea level altitude is displayed on the screen, shortcut operation * (press and hold the MODE1 button for 3 sec) moves to the Setup mode “Correcting the sea level altitude” (page 60) for quick altitude correction. This shortcut operation however does not work while the measurement is continuing in the Sports mode.

Alarm clock mode

Indicates with an alarm sound when the current time reaches any pre-set time. When it reaches a predetermined time, the wristwatch switches to Clock mode, and sounds an alarm for 20 seconds regardless of the mode displayed. Press any button on the wristwatch to stop the alarm.

Press and hold the * MODE1 button for 3 sec in the Clock mode (except when the current sea level altitude is displayed) to turn on/off the alarm clock. The icon

appears on the screen when the alarm clock is on. For setting the alarm clock, see the Setup mode “Setting the * alarm clock” (page 51).

Clock mode (CLOCK)

Displays the current time in the 12- or 24-hour format.

Displays the current date.

Displays the current day of the week.

Altitude

Displays the current altitude.

Temperature

Displays the current temperature.

To altitude correction screen (page 60)

Alarm clock on/off

(press & hold for 3 sec)

Alarm clock icon

MODE1

MODE2

MODE1

Shortcut

(press & hold for 3 sec)

When the measurement

is stopped

Page 26

ENG-25

Sports mode

Continue

Switching to Sports mode

Select “SPORTS MENU” by pressing the MENU button until display switches to Sports mode.

Function in Sports mode

The Sports mode is for measurement using the cyclocomputer and heart rate monitor functions. 4 types of data such as the heart rate, altitude, and slope are displayed on the screen. These data can be switched by pressing the MODE1 or MODE2 button. The displayed data are as follows.

Measurement is maintained even if switched to another mode.*

Upper and middle display data (Switch using the MODE1 button)

Upper display : Displays data related to the speed and altitude. Middle display (left) : Displays data related to the heart rate. Middle display (right): Displays data related to the cadence, temperature and slope

angle.

*1 When the measurement is stopped in

the altitude screen, shortcut operation (press and hold the MODE1 button for 3 sec.) moves to the Setup mode “Correcting the sea level altitude” (page 60).

Sports mode (SPORTS)

Switch pressing the MODE1 button

Heart rate/Cadence

Current speed

Average heart rate/ Average cadence

Heart rate / Slope angle

Ascending altitude

Maximum heart rate/ Maximum cadence

Heart rate / Temperature

Altitude

Shortcut

MODE1

Average speed Maximum speed

MODE1

(press & hold

for 3 sec) To altitude correction screen (page 60)

When the

measurement is

stopped

Page 27

ENG-26

Sports mode

Lower display data (Switch using the MODE2 button)

Displays additional ride data.

*1 The training function screen displays one of the following; countdown distance,

countdown time, or interval. For details, see “Training function (countdown function and interval function)” on page 32.

When measurement is stopped in the training function screen, shortcut operation (press and hold the MODE2 button for 3 sec.) moves to the Setup mode “Setting the training function” (page 36).

Starting/Stopping measurement

”km/h [mph]” or “m [ft]” icon ﬂashes during speed measurement. Initially, the auto-mode function which starts or stops measurement automatically in sync with the bicycle motion is ON. Auto measurement is switched to manual measurement and vice versa by ON/OFF operation in the auto-mode. For details, see the Setup mode “Setting the auto-mode” (page 58). The maximum speed, maximum heart rate, and maximum cadence are updated regardless of starting/stopping the measurement.

To use this unit as a heart rate monitor, start/stop the measure-* ment using the SSS butt on in the manual measurement. When the auto-mode is on, you cannot start the measurement.

Auto-mode (automatic measurement)

When the auto-mode is on,

appears on the screen. The wristwatch detects the

wheel spinning, and starts/stops the measurement automatically.

When the transmission is stopped and Sensor signal icons * and are off, the measurement will not start even after the bicycle starts. If a bicycle is stopped for more than 5 minutes or if heart rate sensor is either far from the bicycle or off the body, it will go into sleep. This normally happens when taking a rest during the ride. To recover from the transmission sleep, press the MODE1 or MODE2 button to turn on the sensor signal icons. For details, see “Transmission sleep mode” on page 23.

AT icon

Switch pressing the MODE2 button

Elapsed time

Clock

Trip distance

Calorie Consumption

Training function

Lap timer

MODE2

Shortcut

(press & hold for 3 sec)

To the setting count-down screen in Option mode (page 36)

When the

measurement is

stopped

Page 28

ENG-27

Sports mode

Continue

Manual measurement

When the auto-mode is off ( is off), use the SSS button to start/stop the measurement.

Stop reminder

The stop reminder function Reminds the rider with an alarm incase the stopwatch is forgotten to be stopped after the ride. When any signal is not received from the speed or cadence sensor for 90 seconds while counting the elapsed time, an alarm sounds and “STOP” appears on the screen. This alert display is repeated up to 3 times every 90 seconds. When any sensor signal is detected, the alarm is stopped.

Forgetting to stop the measurement is likely to happen at a rest during a ride or * after a race ﬁnishes. In cases you will start again immediately, such as at trafﬁc signals, or when you use this unit as a heart rate monitor, ignore this. This function cannot be disabled.*

Resetting the measurement data and saving the ﬁles

To reset the measurement data, interval, and lap data to 0, simultaneously press the SSS + MODE1 or SSS + MODE2 buttons on any screen in the Sports mode (except interval on the training function screen). Resetting the measurement data saves the point data, which was recorded at the timing set for the record interval, automatically in a ﬁle. For viewing and deleting the saved data, see the Data mode “File view” (page 40).

The screen will freeze for about 2 seconds after resetting; * however, all measurements are operating normally. After you reset, the countdown distance, countdown time, and interval are returned * to the predetermined value you set. Cannot reset for 5 seconds after pressing the * LAP button. The wristwatch has a limited memory capacity. When the data volume exceeds the * memory capacity, any new data can no longer be saved. For details, see the Data mode “File view” (page 40). Resetting with the interval (* INT) displayed on the training function screen resets the measurement data of the interval only. For details, see “Training function (countdown function and interval function)” on page 32.

MODE1

SSS

MODE2SSS

(Simultaneously press)

Stop reminder

Page 29

ENG-28

Sports mode

Display data in Sports mode (upper and middle display)

Switch pressing the MODE1 button

Current speed

Displays the current speed in real time. Updates every second.

Heart rate

Displays the current heart rate in real time. Updates every second.

Cadence

Displays the current number of pedal rotations per minute. Updated every second.

Average speed

Displays the average speed since the start of measurement.

Average heart rate

*1*2

Displays the average heart rate since the start of measureme nt. The time with no heart rate measured is not reﬂected on the average rate.

Average cadence

*1*3

Displays the average cadence since the start of measurement. Any time with no pedaling is not reﬂected on the average cadence.

Maximum speed

Displays the maximum speed since the start of measurement.

Maximum heart rate

Displays the maximum heart rate since the start of measurement.

Maximum cadence

Displays the maximum cadence since the start of measurement.

Sea Level Altitude

Displays the sea level altitude at the current location point.

Temperature

Displays the current temperature.

Ascending altitude

Displays the accumulated altitude from the point you reset to the current point. * Any descending altitude is not counted.

Slope angle

Displays a ±value on the basis that the slope angle of 45° is 100%.

*1 Each average value is displayed on the screen replaced with the character “E” when the elapsed

time (TM) exceeds 100 hours. Clear the data by resetting (page 27). The average speed is displayed in the same way as above when the trip distance exceeds 10000 km [mile].

*2 This device stops calculating the average when the heart rate sensor is detached, and resumes

the calculation when the heart rate sensor is worn again. This feature produces actual averages with the heart rate sensor worn.

This device calculates the average excluding the time when you stop pedaling. This feature produces actual averages, unlike other models that calculate averages also to include any zero values.

MODE1

(press & hold for 3 sec) (When the measurement is stopped)

Shortcut

Page 30

ENG-29

Sports mode

Continue

Display data in Sports mode (lower display)

Switch pressing the MODE2 button

TM Elapsed time

Displays the elapsed time from the start of measurement to the 1/10 second. When it exceeds 99:59’59”, it repeats from 00’00”0.

DST Trip distance

Displays the trip distance from the start of measurement.

Training function (page 32) Displays any one selected from the countdown distance, countdown time, and interval.

C.D. DST Countdown distance

Count s down the predeterm ined distance, and displays the remaining distance.

C.D. TM Countdown time

Counts down the predetermined time, and displays the remaining time.

INT Interval (interval time/ recovery time)

Counts down the predetermined time (interval time), and then counts up automatically as a recovery time after the time is up. Pressing the LAP button starts the interval time again, which allows you to repeat a high and low intensity exercise.

LAP Lap timer

Displays the elapsed time from the previous point (for

LAP 01: from the start of measurement) in real time.

CAL Calorie Consumption

Displays the estimated calorie consumption from the start of measurement based on the heart rate.

Clock

Displays the current time of day in the 24- or 12-hour system.

*4 Each maximum value is updated regardless of starting or stopping the measurement. *5 When the measurement is stopped, take a shortcut (press and hold the MODE1 button for 3 sec.)

to the Setup mode “Correcting the sea level altitude” (page 60).

*6 The slope angle value is updated every 2 seconds calculated from several changes of altitude

and the trip distance. This may cause some delays in an update. Temporarily abnormal values may also be displayed because of rapid changes of speed or running at a low speed.

*7 When the measurement is stopped, take a shortcut (press and hold the MODE2 button for 3 sec.)

to the Setup mode “Setting the training function” (page 36).

MODE2

Shortcut

(press & hold for 3 sec)

MODE2

(When the measurement is stopped)

Page 31

ENG-30

Sports mode

Pace function

2 types of pace arrows, for speed and heart rate, are displayed in Sports mode. The arrow icons indicate whether the current speed/ heart rate is above or below the average speed/heart rate.

The current value is above the average.

The current value is below the average.

The current value is equal to the average.

No arrows :

The current value is “0”.

Lap function

Pressing the LAP button during measurement in Sports mode records the measurement data between a given set of points (average lap speed/maximum lap speed, average lap heart rate/maximum lap heart rate, lap time/split time) up to 99 points*. Immediately after recording, the lap data is displayed in the order as shown in the ﬁgure below, and then the display returns to the previous screen.

The maximum number of lap records may decrease depending on ﬁle utilization. * For details, see “Wristwatch memory capacity limit” on page 40.

Average lap speed Displays the average lap speed/heart rate from the previous

point (for LAP 01: from the start of measurement) to the current point.

Average lap heart rate

Lap number

Displays the lap number just recorded. *When the total number of laps exceeds 99 points, “--”

appears indicating further lap recording cannot be done.

Lap time

Displays the elapsed time from the previous point (for LAP 01: from the start of measurement).

Split time

Displays the total elapsed time from the start of measurement.

Maximum lap speed

Displays the maximum lap speed/heart rate from the previous point (for LAP 01: from the start of measurement) to the current point.

Maximum lap heart rate

Any screen in Sports mode

Pre vio us screen

Lap data

Current speed

Heart rate

LAP

2.5 sec. 2.5 sec.

Average lap speed

Maximum lap speed

Average lap heart rate

Maximum lap heart rate

Lap time

Split time

Lap number

Page 32

MODE2

ENG-31

Sports mode

Continue

Press the * MODE2 button with the real time lap data to return to the previous Sports mode screen.

Lap time and split time

The lap time displays elapsed time from the last press of the LAP button. The split time displays the elapsed time from the start of measurement to the point LAP button is pressed.

The measured lap data is saved to a ﬁle when * you perform a reset operation (page 27).

Pressing the * LAP button while the total number of laps reaches 99 points displays the lap data, but “--” appears in place of the lap number indicating further recording is impossible.

The lap data can be reviewed in the Data mode “File view”(page 40).*

Real time lap data

Pressing and holding the LAP button on any screen in Sports mode displays the real time lap data in the upper and middle displays. For the real time lap data, the unit starts/stops the measurement in sync with the primary measurement; however, it resets and restarts the data every time you press the LAP button. This independent feature of lap time can be useful also for pace checks in a lap and sectional trials such as hill climb section.

Start of measurement

Lap time 1

Split time 1

Split time 2

Lap time 2

LAP LAP

Previous screen

Real time lap data

Average lap speed

Maximum lap speed

Average lap heart rate

(press &

hold)

Maximum lap heart rate

Lap timer *

Average lap cadence

Lap distance

Maximum lap cadence

Any screen in Sports mode

LAP

MODE1

Page 33

ENG-32

Sports mode

Training function (countdown function and interval function)

This unit has a countdown function that counts down the predetermined time and indicates when the time is up by setting the target trip distance and elapsed time, and an interval function that is used to set the interval time for a given training. The training function includes both these 2 functions.

Either the countdown function or interval function is displayed in the lower display. For display * of the training function, see “Display data in Sports mode (lower display)” on page 29.

Select the training function and enter the respective setting values in “Setting the * training function” (page 36) in Option mode. Display Option mode in the MENU screen or shortcut (press and hold MODE2) to the training function setting screen.

Countdown distance

Displays the countdown distance to a predetermined target trip distance. When it reaches the target trip distance, the unit switches the lower display to the countdown data in any Sports mode display, and notiﬁes by ﬂashing the numerical value/icon and an alarm sound.

Resetting returns the numerical value to the predetermined * value you set.

Example of how the countdown distance is used:

Entering the race event distance

For distance system events such as a road race and century ride, enter the race event distance before the start, and develop your strategy and pace based on the countdown distance during the race.

Entering the destination sign distance

For touring, enter the sign distance whenever you encounter a destination sign along the road, and develop your pace based on the countdown distance.

Entering the periodical target distance

Enter the periodical target distance for a week, month, or year to check your progress.

Countdown time

Displays the countdown time to a predetermined target elapsed time. When it reaches the target elapsed time, the unit switches the lower display to the countdown data in any Sports mode display, and notiﬁes by ﬂashing the numerical value/ icon and an alarm sound.

Resetting returns the numerical value to the predetermined * value you set.

Example how the countdown time is used:

Entering a timed race

For a time endurance race, enter the limit time, and check your pace based on the countdown time.

When the target trip

distance is 20 km

When reached

(displays for 5

seconds)

Beep

When the target

elapsed time is 1 hour

When reached

(displays for 5

seconds)

Beep

Page 34

ENG-33

Sports mode

Continue

Setting the return time limit

Enter the half way time when the ride time is limited, and enjoy your ride without minding the time.

Target time for a Century ride

Enter the target time for big events such as Century ride and Granfondo, and check your pace.

Interval (interval time/recovery time)

Use this function in the interval training.* The interval training is a training method that combines the interval time (high intensity exercise time) and the recovery time (rest time). With this unit, the recovery time is not set for the purpose of simplifying the setup. The recovery time is to be judged by users based on the count-up display of the wristwatch. Judging the recovery time by users enables ﬂexible training menus, in which the recovery time in every repeat is different from the recovery time between the sets (such training that has the recovery time of 3 minutes in every repeat, and 10 minutes between the sets).

You can check recovery progress while riding by viewing the screen.* Depending on the course condition as signals or trafﬁcs, you might not start the *

interval along with the pre-set recovery time.In this case, you can take a training

with smoothness by timing the start on yourself.

Beep

*1 Interval time: Starts countdown from the pre-set time to zero. At zero, switches

to recovery time.

Recovery time: No need to pre-set the recovery time. The wristwatch remains in the recovery period until LAP button is pressed. Press the LAP button at any timing to restart the next interval.

SSS

INT

SSS

REC

LAP

INT

REC

Interval measurement start

Interval restart

In te rval me asurement ﬁnish

An image of interval measurement

Page 35

ENG-34

Sports mode

How to use the interval:

During the interval training, use the interval display to avoid confusing the * start/stop operation with the reset operation.

Setting the interval.

Switch to Sports mode by selecting the interval from the Option mode “Setting the training function”.

Press the MODE2 until “INT” icon displayed in the lower display.

Switch the lower screen :

MODE2

Press the SSS button to start the count down interval measurement. Start a high intensity exercise. The interval time countdown is displayed.

Interval measurement start :

SSS

Use the * SSS button to start/stop the interval even when the auto-mode is on (

lights up). To start the interval measurement, press the SSS

button with the interval displayed in the lower display. Pressing the SSS button with the interval displayed does not affect start/stop of the measurement in the wristwatch. However, the elapsed time measurement in the wristwatch will start just as the interval starts, when the auto-mode is off (

lights off) and measurement is stopped.

When the interval counts down to zero, it will automatically change to recovery

timer, which counts up until next interval is ready. When the interval time reaches the predetermined time, an alarm sounds, various average values and maximum values are displayed in the order as shown in the ﬁgure below, and then the recovery time starts countup. At this point, the wristwatch records the lap data automatically. Measure for any period of time in the recovery time, while relaxing and recovering from fatigue.

Average speed Maximum speed Current speed

Av er age heart rate

Ma xi mu m heart rate

Heart rate

Interval time ﬁnish

Number of intervals

Trip distance in the interval

Recovery time (count-up)

Average cadence

Maximum cadence

Cadence

2.5 sec. 2.5 sec.

Current speed

Heart rate

Cadence

Interval time

Interval time (countdown)

Beep

Page 36

ENG-35

Sports mode

Continue

Press the 5.LAP button to start the next repeat of the interval time again. Start pedaling at your interval intensity. Repeat the steps 4 and 5.

Interval restart :

LAP

When “6.INT” or “REC” is displayed in the lower display, pressing the SSS button stops the interval measurement.

Interval measurement stop :

SSS

To restart the interval measurement, press the * SSS button.

Resetting with the interval displayed resets the interval measurement data only.* The lap data is recorded automatically when the interval measurement starts and *

the interval time is up. When interval measurement is inserted during primary measurement, the lap data is recorded as being continued, like regular lap data.

During the interval measurement, pressing the * LAP button skips the interval time being counted-down, and starts a new countdown.

The interval time stops just as the elapsed time stops in the wristwatch.*

Target heart rate zone

During measurement, the icon “ ” is displayed, which indicates the target heart rate status.

(constant) : The target zone is set to any of HR.ZONE:1 to 5.

(ﬂashing) :

The current heart rate is out of the selected zone.

(off) : The target zone is set to off.

For selecting the zone and setting the zone range, see the Option * mode “Setting the target heart rate zones” (page 37).

Target heart rate zone

Page 37

ENG-36

Option mode

Switching to Option mode

Select “OPTION MENU” by pressing the MENU button until it switches to Option mode.

Function in Option mode

Option mode is used to change the settings of the training function, which is used most frequently in Sports mode, and the target heart rate zone. Switch to various settings as follows.

Setting the training function CD.TIMER

This function is used to select the training function displayed in the lower of the screen, and enter the settings.

Stop the measurement before you change the settings.* In case of shortcutting from Sports mode, proceed to step 2, skipping step 1.* Press and hold only the * MODE1 button to increase the number quickly.

When any other mode screen is displayed, switch to the Option mode “CD.TIMER”. Select “OPTION MENU” by pressing the MENU button several times to switch to “CD.TIMER” automatically. Then, conﬁrm it pressing the SSS button.

Switch the mode :

Conﬁrm :

SSS

Option mode (OPTION)

Setting the training function (countdown/interval)

This function is used to select the countdown or interval, and enter the settings.

Setting the target heart rate zones (page 37) Select the target heart rate zone, and enter the upper and lower limits.

MODE2

MODE1

(or)

Target distance or time currently set

Heart rate zone currently set

Training function currently selected

DST : Countdown distance TIME : Countdown time INT : Interval timer

Page 38

ENG-37

Option mode

Continue

Select the training function displayed in the lower of the screen. Select the “DST (countdown distance)”, “TIME (countdown time)”, or “INT (interval timer)” pressing the MODE1 or MODE2 button, and then conﬁrm it pressing the SSS button.

Select the training function :

MODE2

MODE1

(or)

(DST฀฀TIME



INT)

Conﬁrm :

SSS

Enter the setting. Enter the target value for the function selected in step 2, each digit one by one. Change the value pressing the MODE1 to increase and MODE2 button to decrease the value, and move digits pressing the SSS button.

Increase/decrease :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Press and hold the * MODE2 button for 3 seconds to conﬁrm the changes, and shortcut to the previous Sports mode.

Pressing the

MENU button conﬁrms the change, and returns

to Option mode “CD.TIMER”. To switch to other mode, press the MENU button several times to display the screen of your choice.

To the mode top/switch the mode :

The settings are reﬂected in the lower display in Sports mode. For details, see “Train-* ing function (countdown function and interval function)” on page 32.

Setting the target heart rate zones HR ZONE

Select the registered target heart rate zone (1 to 5) or OFF, change the upper/lower limit of each zone, or set on/off of the zone sound.

Stop measurement and perform the resetting operation (page 27) before you change * the target heart rate zone. If you do not perform the resetting operation, “DATA RESET” appears on the screen and you cannot change the target heart rate zones. For details of the target zone, see “Use of the target zone” (page 67).* The time in the zone measured can be viewed by ﬁle in the Data mode “File view” (page 40).* Press and hold the * MODE1 or MODE2 button to increase/decrease the number quickly.

When any other mode screen is displayed, switch to the Option mode “CD.TIMER”. Select “OPTION MENU” by pressing the MENU button several times to switch to “CD.TIMER” automatically.

Switch the mode :

Target distance or time

Countdown function currently selected

Shortcut from the Sports mode

Page 39

ENG-38

Option mode

Switch to “HR ZONE” pressing the MODE1 or MODE2 button, then conﬁrm it pressing the SSS button.

Switch the screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

The target heart rate zone (* ZONE-1 to 5) or “OFF” currently selected appears on the screen.

Select the target heart rate zone. Select one of “OFF”, “ZONE-1”, “2”, “3”, “4” or “5” pressing the MODE1 or MODE2 buttons. To set the target heart rate zone, select from “1” to “5” and conﬁrm it pressing the SSS button, and then proceed to the step 4. Otherwise, select “OFF” and proceed to step 6.

Select the zone:

MODE2

MODE1

(or)

Conﬁrm :

SSS

Enter the lower limit of the zone currently selected pressing the MODE1 and MODE2 buttons, and conﬁrm it pressing the SSS button. Then, enter the upper limit in the same way, and conﬁrm it pressing the SSS button.

Increase/decrease :

MODE2

MODE1

(or)

Conﬁrm :

SSS

You can enter any upper/lower limit to each zone; however, * the upper limit is adjusted automatically to the lower limit + 1 when the entered lower limit exceeds the upper limit. In case of the upper limit, vice versa, the lower limit is adjusted in the same way. It is no problem even if the upper and lower limit range * overlaps other zones.

Select “ON” or “OFF” of the alarm sound pressing the MODE1 and MODE2 buttons, and conﬁrm it pressing the SSS button.

ON OFF :

MODE2

MODE1

(or)

Conﬁrm :

SSS

When the alarm sound is on, an alarm sounds continuously * as long as the heart rate is outside the target heart rate zone.

Pressing the 6.MENU button conﬁrms the change, and returns to Option mode “HR ZONE”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

Upper limit

Lower limit

Setting the HR alarm zone

He ar t rat e zone currently selected

Page 40

MODE1

MODE2

ENG-39

Data mode

Continue

Switching Data mode

Select “DATA MENU” by pressing the MENU button until it switches to Data mode.

Function in Data mode

The Data mode is used to review and delete the saved ﬁles, download the measurement data to your PC, and review past records.

Data mode (DATA)

Memory point utilization

Number of total laps in all ﬁles Number of total ﬁles saved

File view (page 40) This view is used to review and manage the various data recorded.

PC link (page 45) This is used to send the measurement data to your PC.

The optional “USB communication kit” is required.*

Past records (page 47) Past trip distance and elapsed time can be reviewed by time period.

Page 41

ENG-40

Data mode

File view FILE

The lap and measurement data are saved into a ﬁle automatically each time a ride is reset (Resetting operation on page 27). With the ﬁle view, you can review and delete the ﬁles saved.

Saving and managing the ﬁles

The wristwatch can record up to 30 ﬁles. A new ﬁle is always saved as F01. When the ﬁle volume exceeds the wristwatch memory capacity, the oldest ﬁle is deleted automatically.

F01

F02

F03

F30

Wristwatch memory capacity limit

Data can be saved within the following memory capacity limits.

Number of ﬁles 30 ﬁles Number of laps Laps shall be 99 or less. (* See “Lap data”) Memory for each recording interval Points shall be 36000 or less.

Example At 2 seconds Maximum record of 20 hours

At 3 seconds Maximum record of 30 hours

At 5 seconds Maximum record of 50 hours

At 10 seconds Maximum record of 100 hours

Measurement data to be saved in a ﬁle

Date and time of ﬁle creation (date/time when the measurement started)UÊ

Trip distanceUÊ

Elapsed timeUÊ

Various average values (speed/heart rate/cadence)UÊ

Various maximum values (speed/heart rate/cadence/altitude/temperature/UÊ

slope angle)

Various minimum values (altitude/temperature)UÊ

Ascending altitudeUÊ

Calorie consumptionUÊ

Number of laps usedUÊ

Time distribution to the target zone (time in/above/below the zone) and the UÊ

percentages (%)

Lap data (average lap speed, average lap heart rate, maximum lap speed, UÊ

maximum lap heart rate, lap time, split time, trip lap distance)

Point data at the intervals speciﬁed.UÊ

Old

Date of creation : New

Page 42

ENG-41

Data mode

Continue

Lap dataUÊ

One lap per ﬁle is used even when there is no lap data. Therefore, the total number of laps is the sum of the total number of laps in all ﬁles and the number of ﬁles.

Example) When the following number of laps are recorded in the ﬁles:

Number of laps in a ﬁle Number of ﬁles

F01 : 5 laps

3 ﬁles

F02 : 0 lap F03 : 10 laps

The total number of laps is the sum of the total number of laps in all ﬁles “15”, and the total number of ﬁles “3”, i.e., “18”.

UÊMemory point

This unit has a function to automatically record the data at intervals speciﬁed during measurement (memory point). The recorded data are saved in a ﬁle together with other measurement records and lap data. The memory point can be viewed in “memory point utilization” on the File view. To use such data, you have to send them to your PC (page 46). The automatic record interval can be selected from 4 options in the range of 2 to 10 seconds according to your application. For details, see the Setup mode “Setting the record interval” (page 56).

When the memory point utilization is over 90%, and the remaining memory capacity is low: An alarm sounds during the measurement, “MEMORY” ﬂashes on the screen. This alert is displayed repeatedly every 2 minutes until the data volume exceeds the memory capacity.

When the memory point utilization reaches 100%, and the data volume exceeds the memory capacity: An alarm sounds during the measurement, “MEMORY FULL” ﬂashes on the screen. In this case, the wristwatch automatically saves the data being measured, and creates a ﬁle. Data will be displayed on the screen but now can no longer be saved. The alert is displayed repeatedly every 2 minutes. It is recommended to stop the measurement immediately, and delete the ﬁles in the wristwatch.

When using the optional “USB communication kit”, delete the ﬁles after you * send the saved ﬁles to your PC.

Page 43

ENG-42

Data mode

Viewing the contents in a ﬁle

View the measurement data in a ﬁle saved in the wristwatch.

Switch to the Data mode “FILE”, when any other mode screen is displayed. Select “DATA MENU” by pressing the MENU button several times to switch to “FILE” automatically. Then, conﬁrm it pressing the SSS button.

Switch the mode :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select the ﬁle number you want to view. Select the ﬁle number pressing the MODE1 or MODE2 button, and conﬁrm it pressing the SSS button.

Switching the ﬁle number :

MODE2

MODE1

(or)

Conﬁrm :

SSS

The ﬁle number starts with the latest ﬁle (* F01).

Scroll through the data saved in each ﬁle by pressing the

SSS button.

The display items are as follows on the next page. Pressing the 4.MENU button returns to the Data mode “FILE”.

Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

When the target heart rate zone is set to OFF during measurement, no data re-* lated to the target heart rate zone saved is displayed.

Pressing the * LAP button while viewing data switches to viewing the lap data. For details, see “Viewing the lap data” (page 44).

File number

Number of laps in a ﬁle

Date of ﬁle creation

Time of the start

(Displayed alternately)

Memory point utilization

Number of total laps in all ﬁles

Number of total ﬁles saved

Page 44

ENG-43

Data mode

Continue

Flow of ﬁle view

SSS

Trip time

(hour/minute/second)

Trip distance

(km [mile])

Average speed

Average heart rate

Average cadence

Calorie consumption (kcal)

Maximum speed

Maximum heart rate

Maximum cadence

Time above the zone,

and the percentage

Time below the zone,

and the percentage

Heart rate zone number

Upper zone limit

Lower zone limit

Time in zone, and percentage

Maximum altitude Minimum altitude

Maximum temperature

Minimum temperature

Ascending altitude

Maximum s lo pe angle

Data mode “FILE”

(Displayed alternately)

*1: The zone percentage is displayed as

a guide only, and the total percentage of 3 zones does not come to 100%.

MODE2SSS

MODE1

SSS

Delete ﬁle view screen

(or)

Return

Delete all ﬁles

(to the top screen

of the File view)

Page 45

ENG-44

Data mode

Viewing the lap data

View the lap data in a ﬁle saved in the wristwatch.

Select the ﬁle number you want to view from the Data mode “FILE” (page 42). Select the ﬁle number pressing the MODE1 or MODE2 button, and conﬁrm it pressing the SSS button.

Switching the ﬁle number :

MODE2

MODE1

(or)

Conﬁrm :

SSS

The ﬁle number starts with the latest ﬁle (* F01).

Press the

LAP button to view the lap data contained in the

ﬁle selected. Switch the average value to maximum value display pressing the SSS button. Press the LAP button again to return from the lap data.

Viewing/exiting lap data :

LAP

When no lap data is contained in the ﬁle, it cannot be * viewed.

Switch the laps, if applicable, pressing the

MODE1 and

MODE2 buttons.

Switching the lap number :

MODE2

MODE1

(or)

Pressing the 4.MENU button returns to the Data mode “FILE”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

SSS

Average values Maximum values

Lap number

Lap time

Trip lap distance

Average lap

heart rate

Maximum lap

heart rate

Average lap speed

Maximum lap speed

Split time

File number

Date of ﬁle creation

Time of start

(Displayed alternately)

Number of laps in a ﬁle

Page 46

ENG-45

Data mode

Continue

Deleting ﬁles

You can manually delete the ﬁles saved in the wristwatch. When the data volume exceeds the memory capacity, the wristwatch automatically deletes the oldest ﬁle, and creates a new ﬁle. You can manually delete all ﬁles at once.

Before deleting ﬁles, perform the resetting operation (page 27) in the Sports * mode to save all measurement data. Unless you perform the resetting operation, you can not delete ﬁles. “DATA RESET” appears on the screen for 5 seconds, and then the display returns to the File View screen.

Switch to the Data mode “

FILE” (page 42), and conﬁrm

with the SSS button.

Simultaneously press the SSS button and the MODE1 or MODE2 button to switch to the delete screen.

Switch to Delete:

MODE1

SSS

(or)

MODE2SSS

Pressing the 3.SSS button deletes all ﬁles, and returns to the Data mode “FILE”. Press the MENU button repeatedly to switch to another mode.

Delete all ﬁles :

SSS

Cancel deleting ﬁles :

To the mode top/switch the mode :

Pressing the * MENU button on the delete screen cancels deleting ﬁles, and returns to the previous screen.

When the wristwatch has no ﬁles (* F00) the delete ﬁle operation is not operable. Once any ﬁle is deleted, all lap data contained in the ﬁle are also deleted.* Once a ﬁle is deleted, it cannot be restored.*

PC link PC LINK

The PC link is used for two-way communication with your PC to which download software “e-Train Data™ ver.4” is installed. You can send the data measured with this unit to your PC, and change various settings in the wristwatch from your PC. The optional “USB communication kit” and installation of the “e-Train Data™ ver.4 (Windows version)” contained in the CD-ROM supplied are required to use this function.

For using the ﬁles sent, refer to the e-Train Data™ ver.4 instruction manual contained * in the CD-ROM supplied.

Delete ﬁle view screen

Page 47

ENG-46

Data mode

Communication between your PC and this unit

Send the ﬁles saved in the wristwatch to your PC, or reﬂect the settings changed from your PC in the wristwatch.

Boot your PC, and connect the USB communication unit to the your PC.

Start e-Train Data™ ver.4, and click the “

Communication”

button on your PC screen. Prepare for sending the data according to the instructions displayed on your PC screen.

Switch to the Data mode “FILE”, when any other mode screen is displayed. Select “DATA MENU” by pressing the MENU button repeat- edly to switch to “FILE” automatically.

Switch modes :

Switch to “PC LINK” pressing the MODE1 or MODE2 but- ton, and then press the SSS button. “LINK-TO PC” appears on the screen, and the wristwatch automatically starts searching for your PC. Once the communication is established, it switches to “SEND FILE”, and starts sending the data.

Switch the screen :

MODE2

MODE1

(or)

Search PC / Send the data :

SSS

When communication with your PC cannot be established, * “LINK-TO PC FAIL” appears. Press the SSS button to return to “PC LINK”, and check the condition of your PC. Pressing the SSS button again restarts searching for your PC.

Pressing the * MENU button while sending the data displays “LINK-TO PC FAIL”, and stops sending the data. Pressing the SSS button returns to “PC LINK”.

Depending on the number of ﬁles saved, it takes up to 5 * minutes to send the data.

Searching for your PC

SSS

USB communication unit

Sending data

Page 48

ENG-47

Data mode

Continue

Once sending data is completed, “SEND FILE END” appears. Press the SSS button and return to the data mode “PC LINK”.

To the mode top :

SSS

Press the 6.MENU button repeatedly to switch to another mode.

To switch modes :

Data to be sent from this unit to your PC

The data to be sent to your PC are as follows.

File numberUÊ

Date/time of ﬁle creation (date/time when the measurement started)UÊ

Measured values of the speed, heart rate, cadence, trip distance, elapsed time, UÊ

and sea level altitude, at the record intervals speciﬁed

Lap data (lap number, average lap speed, average lap heart rate, Average lap UÊ

cadence, maximum lap speed, maximum lap heart rate, maximum lap cadence, lap time, split time, and lap distance), Time in the heart rate zone (over / within the range / under)

The wristwatch has a limited memory capacity. It is recommended to transfer * the measurement data periodically to your PC, and delete the ﬁles in the wristwatch (page 45).

Settings to be changed from your PC

The date, clock, on/off and time of the alarm, tire circumference, speed unit, record interval, total trip distance/total elapsed time, auto-mode setting, sound setting, and sea level altitude HOME setting.

Past records VIEW LOG

The past records allow you to view the trip distance and elapsed time by time period, which are essential for your training management.

Total trip distance (UÊODO) and total elapsed time (TTM) since beginning use of this unit

Weekly trip distance and time since MondayUÊ

Monthly trip distance and time since the 1stUÊ

Yearly trip distance and time since January 1stUÊ

You can adjust effectively the training menu by receiving and analyzing the actual training volume of each period of time.

Completion of sending

Page 49

ENG-48

Data mode

Switch to the Data mode “FILE”, when any other mode screen is displayed. Select “DATA MENU” by pressing the MENU button several times to switch to “FILE” automatically.

Switch modes :

Switch to “VIEW LOG” pressing the MODE1 or MODE2 buttons, and conﬁrm pressing the SSS button.

Switch the screen :

MODE2

MODE1

(or)

Conﬁrm:

SSS

The total trip distance and total elapsed time since ﬁrst use of

the wristwatch are displayed. The weekly, monthly, and yearly trip distance and elapsed time are displayed in sequence by pressing the SSS button.

Press the 4.MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

Once you change any date in the past according to the Setup mode “Setting the clock/* date” (page 50), some integrated values for the year, month, or week are deleted according to the relevant changes.

Total elapsed

time and total

trip distance

Elapsed time

and trip distance

for the week

Elapsed time

and trip distance

for the month

Elapsed time

and trip distance

for the year

When the year is changed

Retained Deleted Deleted Deleted

When the month is changed

Retained Deleted Deleted Retained

When the day is changed Retained Deleted Retained Retained

The trip distance of “Past records” in the data mode is integrated regardless of start-* ing or stopping of the measurement. Therefore, the trip distance may differ from that in the sports mode which is interlocked with the start/stop of the measurement. The measurement time is integrated into the elapsed time.* Once “* MEMORY FULL” appears on the screen, the elapsed time is no longer added. It will resume when the wristwatch attains an available capacity.

Total trip distance Weekly trip distance Monthly trip distance Yearly trip distance

Total elapsed time Weekly elapsed time Monthly elapsed time

SSS

Yearly elapsed time

Page 50

MODE1

MODE2

ENG-49

Setup mode

Continue

Setup mode (SETUP)

Switching to Setup mode

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen, then the wristwatch switches to the Setup mode automatically.

Function in Setup mode

Setup mode is used to change various settings of the wristwatch. Switch the setup items pressing the MODE1 or MODE2 button.

Once any setting is changed, conﬁrm it pressing the * MENU button. Unless you perform an operation within 3 minutes, it returns to Clock mode. In such cases, * any change is not reﬂected. Shortcut from Clock mode or Sports mode does not display the altitude adjusting screen * as shown in the ﬁgure below. It directly switches to the setting entry screen.

Setting the

clock/date

Correcting the sea

level altitude

(page 50)

(page 60)

Setting the

alarm clock

Setting sound

(page 51)

(page 59)

Setting the tire

circumference

Setting the auto-mode

(page 52)

(page 58)

Searching for

sensor ID

Total trip distance/total

elapsed time entry

(page 53)

(page 57)

Setting the

measurement unit

Setting the

record interval

(page 55)

(page 56)

(press & hold)

Page 51

ENG-50

Setup mode

Setting the clock/date CLOCK DATE

Set the “Clock display format”, “Hour”, “Minute”, “Date display format”, “Year”, “Month” and “Day”.

Once you change any date in the past, some integrated values for the year, month, * or week in the Data mode “Past records” (page 47) are deleted according to the relevant changes.

Press and hold the * MODE1 or MODE2 button to increase/decrease the number quickly.

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen. The wristwatch switches to “CLOCK DATE” automatically. Then, conﬁrm it with the SSS button.

Switch the mode :

(press & hold)

Conﬁrm :

SSS

Select the clock display format. Select “24h (24 hour)” or “12h (12 hour)” pressing the MODE1 and MODE2 buttons, and conﬁrm with the SSS button.

24h 12h :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Enter the “Hour” or “Minute”. Enter the “Hour” pressing the MODE1 and MODE2 buttons, conﬁrm with the SSS button, and then enter the “Minute” in the same way.

Increase/decrease :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select the date display format. Select the date display format from “YY.MM.DD”, “DD.MM.YY”, and “MM.DD.YY” pressing the MODE1 and MODE2 buttons, and conﬁrm with the SSS button.

Switch the display :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Enter the “Year”, “Month” and “Day”. Enter the “Year”, “Month” and “Day” in the display order selected in Step 4 pressing the MODE1 and MODE2 buttons, and conﬁrm with the SSS button. Enter only the last 2 digits of the year.

Increase/decrease :

MODE2

MODE1

(or)

Conﬁrm :

SSS

YY/MM/DD

Display format

Hour

Minute

Page 52

ENG-51

Setup mode

Continue

Pressing the 6.MENU button conﬁrms the change, and returns to the Setup mode “CLOCK DATE”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

Setting the alarm clock ALARM

Set the alarm in Clock mode.

Press and hold the * MODE1 or MODE2 button to increase/decrease the number quickly.

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen. It switches to “CLOCK DATE” automatically.

Switch modes:

(press & hold)

Switch to “ALARM” pressing the MODE1 or MODE2 button, and then conﬁrm it pressing the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select “ON” or “OFF” pressing the MODE1 or MODE2 button. To use the alarm clock, select “ON” and press the SSS button to proceed to Step 4. Otherwise, select “OFF” to proceed to Step 5.

ON OFF:

MODE2

MODE1

(or)

Conﬁrm :

SSS

You can set on/off of the alarm clock also in Clock mode. * When it is on,

icon appears.

Enter “Hour” and “Minute”. Enter “Hour” pressing the MODE1 and MODE2 buttons, and conﬁrm it pressing the SSS button. Then, enter “Minute” in the same way.

Increase/decrease:

MODE2

MODE1

(or)

Conﬁrm :

SSS

MinuteHour

Page 53

ENG-52

Setup mode

Pressing the 5.MENU button conﬁrms the change, and returns to the Setup mode “ALARM”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

Setting the tire circumference TIRE

Set the tire circumference (peripheral length) to SP1 (Speed sensor 1) and SP2 (Speed sensor 2) synchronized according to “Searching for sensor ID” (page 53).

For the tire circumference, see “Tire circumference” (page 17).* Press and hold the * MODE1 or MODE2 button to increase/decrease the number

quickly.

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen. It switches to “CLOCK DATE” automatically.

Switch modes:

(press & hold)

Switch to “TIRE” pressing the MODE1 or MODE2 button, and then conﬁrm it pressing the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select (Sensor 1) or (Sensor 2) by pressing the MODE1 or MODE2 button.



MODE2

MODE1

(or)

Conﬁrm :

SSS

When using a wristwatch for a single bicycle, set the tire * circumference to

(Sensor 1) only. When using a wristwatch commonly for two bicycles, sets the tire circumference of the second bicycle to

(Sensor 2).

Sensor currently selected

Tire circumference set to the sensor currently selected

Page 54

ENG-53

Setup mode

Continue

Enter the last 2 digits for the tire circumference of the sensor selected in Step 3 using the MODE1 and MODE2 buttons, and move digits using the SSS button. Then, enter the ﬁrst 2 digits in the same way.

Increase/decrease:

MODE2

MODE1

(or)

Move digits:

SSS

Pressing the 5.MENU button conﬁrms the change, and returns to the Setup mode “TIRE”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

Switching to the Sports mode displays the sensor icon (* or ) selected. Even when a wristwatch is commonly used for 2 bicycles, the speed sensor is recognized automanically; accordingly, the measurement can be started appropriately (it may take time to recognize it automatically depending on the situation). For details, see “Automatic recognition of the speed sensor ID” on page 7.

Searching for sensor ID SYNC ID

Pairing the wristwatch with the heart rate and speed/cadence sensors.

This unit requires checking of the sensor ID in order for the wristwatch to receive signals * from the sensors. Once you format the wristwatch, or when you use a new sensor, synchronize the sensor ID according to the following procedure.

When you use the unit for the ﬁrst time (at factory default setting), each sensor * ID has been synchronized to the wristwatch in the package; accordingly, the following procedure is not required.

To synchronize the sensor ID, each sensor must be near the wristwatch.* Check that there is not any other sensor of the same type nearby. *

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen. It switches to “CLOCK DATE” automatically.

Switch modes:

(press & hold)

Switch to “SYNC ID” pressing the MODE1 or MODE2 button, and then conﬁrm it pressing the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Page 55

ENG-54

Setup mode

Select the sensor ID to be checked. Select from “HR (heart rate sensor)”, “SP1 (speed sensor 1)”, and “SP2 (speed sensor 2)” pressing the MODE1 and MODE2 buttons, and then conﬁrm it pressing the SSS button.

HR SP1  SP2:

MODE2

MODE1

(or)

Conﬁrm :

SSS

SP2* is used when a wristwatch is commonly used for 2 bicycles. Once you synchronize the ID of the second bicycle equipped with a sensor with SP2 in advance, the wristwatch can identify the second bicycle automatically.

Press the SSS button to start searching for the ID. When you select “SP1” or “SP2”, press the RESET button on the speed sensor. When you selected “HR”, wear the heart rate sensor (page 13), or transmit a sensor signal according to the following simple method below. When the heart rate or speed/cadence is displayed with “ID-OK” on the screen, synchronization is completed.

Start searching :

SSS

This unit enters the search mode for 5 minutes after starting * the ID sync. Press the SSS button in the search mode to cancel the ID synch, and “ID-SKIP” is displayed. If any sensor signal is not received in 5 minutes, “ID-ERROR” is displayed. When “ID-SKIP” or “ID-ERROR” is displayed, the ID has not been synchronized properly.

*Even when the heart rate sensor is not worn,

it transmits a heart rate signal by rubbing both electrode pads with your thumbs.

Pressing the

MENU button conﬁrms the change, and returns

to the Setup mode “SYNC ID”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode:

When you use * SP2, set the tire circumference of (Sensor 2) according to “Setting the tire circumference” (page 52).

Electrode pad

Page 56

ENG-55

Setup mode

Continue

Setting the measurement unit UNITS

Change the speed unit and temperature unit.

Stop measurement and perform the resetting operation (page 27) before you change * the unit. Unless you perform the resetting operation, “DATA RESET” appears on the screen, preventing change of the unit.

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen. It switches to “CLOCK DATE” automatically.

Switch modes :

(press & hold)

Switch to “UNITS” pressing the MODE1 or MODE2 button, and then conﬁrm it pressing the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select the speed unit pressing the MODE1 or MODE2 button. To switch the speed unit only, proceed to Step 5. To change the temperature unit afterwards, press the SSS button, and then proceed to Step 4.

km/h mph :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select the temperature unit using the MODE1 and MODE2 buttons.

˚C ˚F :

MODE2

MODE1

(or)

Pressing the 5.MENU button conﬁrms the change, and returns to the Setup mode “UNITS”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

After the measurement unit is switched, the total distance measured in the past is * automatically converted to the new unit.

Current speed unit

Current

temperature unit

Page 57

ENG-56

Setup mode

Setting the record interval SAMPLE RATE

In primary measurement, the measurement data is recorded in the selected intervals (seconds).

Stop the measurement and perform the resetting operation (page 27) before you * change the record interval. Unless you perform the resetting operation, “DATA RESET” appears on the screen, preventing change of the record interval.

You cannot set the record interval to off.*

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen. It switches to “CLOCK DATE” automatically.

Switch modes :

(press & hold)

Switch to “SAMPLE RATE” pressing the MODE1 or MODE2 button, and then conﬁrm it pressing the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select “T-10s (10 seconds)”, “T-5s (5 seconds)”, “T-3s (3 seconds)” or “T-2s (2 seconds)” pressing the MODE1 or

MODE2 buttons.

T-10s  T-5s  T-3s  T-2s :

MODE2

MODE1

(or)

Pressing the 4.MENU button conﬁrms the change, and returns to the Setup mode “SAMPLE RATE”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

The wristwatch stores up to 36000 points of data, and the maximum record time * (maximum time up to the memory point utilization of 100%) depends on the intervals of the seconds selected. The following time lengths can be used as a guideline.

T-10s (at intervals of 10 seconds) : up to 100 hours T-5s (at intervals of 5 seconds) : up to 50 hours T-3s (at intervals of 3 seconds) : up to 30 hours T-2s (at intervals of 2 seconds) : up to 20 hours

The current memory point utilization can be viewed in the Data mode “File view” * (page 40).

Current record interval

Page 58

ENG-57

Setup mode

Continue

Total trip distance/total elapsed time entry TOTAL DATA

You can enter any values to the total trip distance and total elapsed time in the Data mode “Past records” (page 47), then you can start with the values entered. The total trip distance and total elapsed time can be retained even after formatting the wristwatch or replacing the wristwatch.

Press and hold the * MODE1 or MODE2 button to increase/decrease the number quickly.

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen. It switches to “CLOCK DATE” automatically.

Switch modes:

(press & hold)

Switch to “TOTAL DATA” pressing the MODE1 or MODE2 button, and then conﬁrm it pressing the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

For entry, change each digit one by one for the total trip distance

by pressing the MODE1 or MODE2 button, and move digits by pressing the SSS button. (6-digit integer number) To enter the total trip distance only, proceed to Step 5 after the entry. To enter the total elapsed time at the same time, move digits to the far left, and then proceed to Step 4 by pressing the SSS button.

Increase/decrease:

MODE2

MODE1

(or)

Move digits:

SSS

For entry, change each digit for the total elapsed time by pressing the MODE1 or MODE2 button, and move digits by pressing the SSS button.

Increase/decrease:

MODE2

MODE1

(or)

Move digits:

SSS

Pressing the 5.MENU button conﬁrms the change, and returns to the Setup mode “TOTAL DATA”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

Total trip distance

Total elapsed time

Page 59

ENG-58

Setup mode

Setting the auto-mode AUTO MODE

Switch on/off of the auto-mode (page 26).

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen. It switches to “CLOCK DATE” automatically.

Switch modes :

(press & hold)

Switch to “AUTO MODE” pressing the MODE1 or MODE2 button, and then conﬁrm it pressing the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select “ON” or “OFF” pressing the MODE1 or MODE2 button.

ON OFF:

MODE2

MODE1

(or)

Pressing the 4.MENU button conﬁrms the change, and returns to the Setup mode “AUTO MODE”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

Current setting

Page 60

ENG-59

Setup mode

Continue

Setting sound SOUND

Switch on/off of the button operation sound and target heart rate zone alarm sound.

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen. It switches to “CLOCK DATE” automatically.

Switch modes :

(press & hold)

Switch to “SOUND” pressing the MODE1 or MODE2 button, and then conﬁrm it pressing the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select “ON” or “OFF” of the button operation sound pressing the MODE1 or MODE2 button. To switch the button operation sound only, proceed to Step

5. To change also the target heart rate zone alarm sound, press the SSS button, and then proceed to Step 4.

ON OFF:

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select “ON” or “OFF” of the target heart rate zone alarm sound pressing the MODE1 or MODE2 button.

ON OFF:

MODE2

MODE1

(or)

Pressing the 5.MENU button conﬁrms the change, and returns to the Setup mode “SOUND”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

Page 61

ENG-60

Setup mode

Correcting the sea level altitude ALT

Correct the sea level altitude.

Stop the measurement before you change the settings.* In case of shortcutting from Clock mode or Sports mode, proceed to the step 2 * skipping the step 1. For details of the altitude, see “Basic knowledge of the altitude measurement” on page 61.* Press and hold the * MODE1 or MODE2 button to increase/decrease the number quickly.

Press and hold the MENU button in the Clock mode or Sports mode until “SETUP MENU” appears on the screen. It switches to “CLOCK DATE” automatically.

Switch modes :

(press & hold)

Switch to “ALT” using the MODE1 or MODE2 button, and then conﬁrm it using the SSS button.

Switch screen :

MODE2

MODE1

(or)

Conﬁrm :

SSS

Select “REF (correcting the sea level altitude)” or “HOME (home altitude)” with the MODE1 and MODE2 buttons, and then conﬁrm it with the SSS buttons.

There are 2 ways to correct the sea level altitude with this unit. One * is REF (correcting the sea level altitude), and HOME (home altitude), the other. For details, “Sea level altitude correction” on page 61.

Select “+” or “-“ of the sea level altitude. Then, change each digit one by one for the value using the MODE1 and MODE2 buttons, and move digits using the SSS button.

Increase/decrease:

MODE2

MODE1

(or)

Move digits:

SSS

The altitude is entered in 4 digits in the unit of meter, 5 * digits in the unit of feet, both in integer numbers. Pressing and holding the * MODE1 button for 3 seconds conﬁrm the changes, and shortcuts to the previous Clock mode or Sports mode.

Pressing the 5.MENU button conﬁrms the change, and returns to the Setup mode “ALT”. Press the MENU button repeatedly to switch to another mode.

To the mode top/switch the mode :

Current sea level altitude

Shortcut from the Clock mode or Sports mode

Page 62

ENG-61

Continue

Altitude measurement function

This unit measures the atmospheric pressure using a built-in pressure sensor and determines the altitude. It estimates the altitude using the relation between the altitude and pressure of ISO 2533 (Standard atmosphere), which was developed based on the international standard atmosphere speciﬁed by the International Civil Aviation Organization (ICAO). Generally, a conventional pressure sensor is affected by temperature and can cause a large margin of error, but this unit is temperature-compensated and records 1 meter resolution. This unit is designed not to reﬂect the change in atmospheric pressure to the altitude measurement except during a ride; therefore, the altitude is less prone to weather changes, so while not in motion, value shift is minimal.

The altitude measurement may change temporarily when going outside from an indoor * room. This is due to a rapid temperature change, and is not a malfunction. It will return to the normal value after a while.

Sea level altitude correction

There are 2 ways to correct the sea level altitude with this unit. It is recommended to correct the sea level altitude just before measurement, taking either following methods.

The sea level altitude correction screen is displayed in Setup mode in the * MENU, or is shortcut to from the orthrometric height screen in Clock mode or in Sports mode.

UÊREF (sea level altitude correction): Enter the altitude at the current point.

Enter the actual value at the point where the sea level altitude is well known, such as along the seashore, or at a sign on the mountain, etc.

Press and hold * MODE1 and SSS, or MODE2 and SSS, simultaneously on the setting screen to reset the corrected value to the default value (a value according to ISO2533).

UÊHOME (home altitude setting): Apply the altitude set beforehand.

Preset the sea level altitude at your home in advance. Move to the ALT HOME screen, and then return to Clock mode or Sports mode by

pressing MENU or the relevant shortcut. Then, the sea level altitude changes to the preset value. You can start with the correct sea level altitude by setting home altitude before starting from your home.

Timing for updating the sea level altitude, ascending altitude, and temperature

The timing for updating the sea level altitude, ascending altitude, and temperature data differs depending on whether the Sports mode is in measurement or is stopped.

Condition Timing for updating

When the Sports mode is in measurement, and a speed sensor signal is received

5 seconds

When the Sports mode is stopped, or no speed sensor signal is received

5 minutes

This is also valid in Clock mode.*

Basic knowledge of the altitude measurement

Page 63

ENG-62

Relation between the altitude and atmospheric pressure

The higher the altitude, the lower the atmospheric pressure. At an altitude of 500 m or less, the pressure changes by 12 hPa per 100 m of altitude.

Knowledge related to weather and altitude

The change in atmospheric pressure when the weather changes from a good condition such as clear and sunny, to a bad condition such as rainy and cloudy is equivalent to the ascending altitude of about 100 m. Thunder storms will be result in even larger changes. Furthermore, the atmospheric pressure measurements may change more than 30 m in altitude change from sunrise to sunset even under stable clear weather conditions.

2 3

Page 64

ENG-63

Continue

This section is just a general overview of training with heart rate data. For more complete information, there are books and websites with more in-depth information. Generally, the heart rate increases during exercise, getting higher in conjunction with the intensity of the workout. The measurement of your heart beat is a good indicator of the intensity of your workout. By setting target HR (heart rate) zones and sticking to pre-set exercises, you will be able to work out more efﬁciently. Before beginning a training program, be sure to ﬁrst consult a medical specialist or sports trainer.

Target heart rate zone

Bicycling is one of the best activities to improve your general ﬁtness. To improve your overall ﬁtness through bicycling, set a target heart rate zone from between 30% and 70% of your maximum HR, depending on your physical strength. For best results, exercise consistently in this zone for periods of at least 20-30 minutes, 3 or more times a week. Obtain your target heart rate zone from either of the 2 ways below.

Training level for improving general ﬁtness

Check the training level according to your age using the graph below. For beginners, it is recommended to start with the level of 30% of your max. From this point, gradually increase the level according to your ﬁtness level and experience. Training at levels over 70% of your HR max will focus more on anaerobic exercise, and less on aerobic exercise. Weight loss usually occurs through longer rides (over 1 hour) at lower HR levels.

Heart rate training

PULSE RATE (bpm)

AGE

200

180

160

140

120

100

20 30 4 0 50 60 70

TARGET

ZONE

TARGET

ZONE

30%

40%

50%

60%

70%

80%

Exercise Level

30%

40%

50%

60%

70%

80%

MAXIMUM HEART RATE (204 – 0.69 x AGE)MAXIMUM HEART RATE (204 – 0.69 x AGE)

190 – AGE

180 – AGE

190 – AGE

180 – AGE

Page 65

ENG-64

Obtaining individual heart rate zone for building up power

Athletic ability is different from person to person. The effective and reasonable target heart rate zone has to be obtained from the actual ride data. A time trial for 20 minutes or 5 km (hereinafter abbreviated as TT) is required to measure the actual data. Perform the TT under the following conditions, according to the speciﬁed procedure.

TT is a training item, in which riders bicycle a speciﬁed distance at full speed. * The last half is especially a very physically demanding workout. Maintain the pace so that you can ride the speciﬁed distance at a stable speed.

Conditions for time trials

For the TT measurement, a continuous ride for 20 minutes is ideal. When such a course that you can ride continuously for 20 minutes is not available, use a 5 km course that you can ride continuously. Measure the course distance in advance, and specify the start and goal points. Repeat the TT twice, and calculate the average of the average heart rates in the 2 sessions, which will be used as an average level for setting the zone.

Procedures for time trial measurements Caution:

Maintain a good physical condition. If you have any worries, consult with UÊ

a doctor before you attempt any time trial.

Do not perform any TT on a road where many signals are located and the UÊ

trafﬁc is heavy.

Be sure to pay attention to the road ahead during a TT.UÊ

Perform a TT in a week which is scheduled with relatively mild training.* Warm up sufﬁciently at least for 30 minutes before you attempt any TT.* Select the manual measurement (on page 27).*

Stop your bicycle at the start point, and reset the wristwatch.

Press the 2.SSS button to start the TT. Gradually accelerate up to a stable speed in the ﬁrst 1-minute. Keep up the intensity level that you feel is moderately difﬁcult. Set a pace so that you do not slow down in the last half, and maintain the pace to the ﬁnish.

Once you reach the goal, stop the measurement by pressing the 3.SSS button.

Cool down for 30 minutes while drinking some water.

Repeat the TT once more.

Repeat Steps 1 to 3. Check the measurement data.

Record the average heart rate of two TT data from the Data mode “File view” (page 40). Record the other data (time, average cadence, average speed, etc.) for your reference.

Page 66

ENG-65

Continue

Obtain your target heart rate zone from the table below according to the

average heart rate recorded.

e.g.) Average heart rate at 20 minutes time trial is 100%.

Heart rate zone level Lower limit Upper limit 1 (Active Recovery) 0 % 64 % 2 (Endurance) 65 % 79 % 3 (Tempo) 80 % 90 % 4 (Lactate Threshold) 91 % 101 % 5 (VO2 Max) 102 % 112 %

An elite ride should set the value 4% lower than those values above.*

For example, when the average heart rate at 20 minutes time trial is 175 bpm, the zone is categorized as the table shown below.

Heart rate zone level Lower limit Upper limit 1 (Active Recovery) 0 112 2 (Endurance) 114 138 3 (Tempo) 139 158 4 (Lactate Threshold) 159 177 5 (VO2 Max) 178 196

Set the calculated value to the heart rate target zone.

For details of setting the heart rate target zone, see “Setting the target heart * rate zones” in Option mode (page 37).

Page 67

ENG-66

Training for competition

Measure your resting heart rate just after waking in the morning and your maximum heart rate (perhaps during competition). Then set your target zone according to your goal:

A) For recovery, endurance training, and weight loss :

60% - 70% (aerobic exercise)

B) For quality endurance and tempo training :

70% - 80% (aerobic exercise)

C) For increasing TT and race ability, and VO2 max :

85% + (anaerobic exercise)

D) For anaerobic capacity and sprinting :

92.5% + (anaerobic exercise)

Training level (%) = x 100

Target heart rate = (Maximum heart rate - Resting heart rate) x

+ Resting heart rate

Resting heart rate

Your resting heart rate is usually the lowest recorded rate soon after waking up in the morning.

Maximum heart rate

The following calculations are generally used: (220 - age) or (204 - 0.69 x age). For more precise ﬁgure, consult a training specialist.

(Target heart rate) - (Resting heart rate)

(Maximum heart rate) - (Resting heart rate)

Training level (%)

100

Page 68

ENG-67

Continue

Use of the target zone

When the heart rate is out of the zone during the measurement, the wristwatch sounds an alarm and notiﬁes the rider by ﬂashing  . The heart rate zone is selected from 5 predetermined zones. For a training aiming at a heart rate of 140 to 160 bpm, select HR.ZONE:3 as shown below. Then, the wristwatch sounds an alarm when the heart rate falls below 140 bpm, or rises above 160 bpm. Once the target zone is set to On, the relevant data are recorded and the time in the zone, time above the zone, and time below the zone and their percentages can be viewed in the ﬁle view (page 40).

The alarm sound is interlocked with the start/stop of the measurement.* You can enter any upper/lower limit to each zone.* Select “OFF” of the target heart rate zone, select Zones 1 to 5, change the upper *

and lower limits, and select “ON” or “OFF” of the zone sound in the Option mode “Setting the target heart rate zones” (page 37). You can select “ON” or “OFF” of the zone sound also in the Setup mode “Setting sound” (page 59).

60 200

bpm

Heart rate

HR.ZONE :1

100 - 120 bpm

HR.ZONE :2

120 - 140 bpm

HR.ZONE :3

140 - 160 bpm

HR.ZONE :4

160 - 180 bpm

HR.ZONE :5

180 - 200 bpm

Default zone

80 100 120 140 160 180

Target training zone

Heart rate zone

ZONE:1

ZONE:2

ZONE:3

ZONE:4

ZONE:5

Alarm Alarm

Page 69

ENG-68

If a malfunction occurs, check the following before contacting CatEye or your retailer for repair or service.

Trouble on display

Trouble Check Items Remedy

Display motion become s slower.

Is the surrounding temperature low (below zero degree Celsius or 32 degrees Fahrenheit)?

Tempera tures below free zing may result in slower screen response. Data is not affected.

icon appears.

The remaining battery capacity for the wristwatch is low.

Replace it with a new battery (CR2430). After replacement, be sure to perform the restarting operation (page 14).

“STOP” appears. The stop reminder function

(page 27) is activated.

Once any sensor signal is received, the st op reminder is canceled. Ignore this during measurement.

“MEMORY” icon ﬂashes on the sc reen eve ry 2 minutes.

The rem aining wr istwat ch memory capacity is low.

It is recommen ded to delet e the files (page

45). When using the optional “USB communication *

kit”, delete the ﬁles after you send the saved ﬁles to your PC.

“M EMOR Y FU LL” i con ﬂashes on the screen every 2 minutes.

The data volume exceeded the wristwatch memory capacity during measurement.

Measurement data can no longer be recorded. Delete the ﬁles (page 45).

When using the optional “USB communication * kit”, delete the ﬁles after you send the saved ﬁles to your PC.

No displays appear. Is the battery for the wrist-

watch empty?

Replace it with a new battery (CR2430). After replacement, be sure to perform the restarting operation (page 14).

Meaningless display appears.

Perform the restarting operation (page 14).

Cannot measure the current speed or cadence.

Is the Speed and Caden ce sensor icon on

icon is off, the wristwatch cannot receive

any data. Press the MODE1 or MODE2 button to cancel the transmission sleep (page 23).

Check whether the distance between the speed/cadence sensor and the magnet is too large.

Adjust the position of the speed/cadence sensor and that of the magnet correctly. (See “Bicycle Installation” on page 10).

Is the se nsor zone of th e speed/cadence sensor off the center of the magnet?

Has the power-saving mode been activated, entering Clock mode?

Press the MENU button to switch to Sp orts mode.

The display may be delayed depending on the wireless transmission condition. Check whether any speed signal i s re ceived by spinning the wheel for a while.

For details, see “Automatic recognition of the * speed sensor ID” on page 7.

Is the battery for the speed sensor empty?

Replace it with a new battery (CR2032).

Did you perform the formatting operation?

The sensor ID was deleted by formatting. Synchronize the speed sensor ID again (page 53).

Trouble shooting

Page 70

ENG-69

Continue

Trouble Check Items Remedy

Measure the current speed, but cannot measure the cadence.

Is the connection on the cadence side of the speed sensor dirty?

The continuity on the cadence side of the speed sensor is bad. Loosen the set screw on the cadence side to remove the cadence sensor. Clean the pins with a dry cloth and replace the sensor. After cleaning, adjust the distance to t he magne t, and then ﬁrmly secure the sensor.

Heart rate signals are not received.

Is the Heart rate sensor icon on

icon is off, the wristwatch cannot receive

any data. Press the MODE1 or MODE2 button to cancel the transmission sleep (page 23).

Has the power-saving mode been activated, entering Clock mode?

Press the MENU button to switch to Sp orts mode.

Is the heart rate sensor atta che d sec ure ly to you r body?

Adjust the electrode pad with its rubber surface to have a good contact with the body.

Dry skin (particularly in winter)

Slightly moisten the electrode pad of the heart rate sensor.

Is the battery for the heart rate sensor used up?

Replace it with a new battery (CR2032).

Check whether

lights up

on the wristwatch screen.

The remaining battery capacity of the wristwatch is low. Replace it with a new battery (CR2430). After replacement, be sure to perform the restarting operation (page 14).

Is the e lectrode pad overly worn and damaged after long use?

Replace it with a new heart rate sensor.

Did you perform the formatting operation?

The sensor ID was deleted by formatting. Synchronize the heart rate sensor ID again (page 53).

Fluctuation in the heart rate indicator, for example it returns to zero and then the he art rat e is m eas ured again.

Is the electro de pad being worn correctly?

To wear the electrode pad correctly, follow the instructions for wearing the heart rate sensor (page 13).

Moving the main unit away from your body will prevent measurement of the heart rate.

Check whether

lights up

on the wristwatch screen.

The remaining battery capacity of the wristwatch is low. Replace it with a new battery (CR2430). After replacement, be sure to perform the restarting operation (page 14).

Is the battery for the heart rate sensor used up?

Replace it with a new battery (CR2032).

The sea level altitude display is wrong.

Have you corrected the sea level altitude?

The sea level altitude may have errors due to the change in atmospheric pressure. Correct the sea level altitude before use (page 60).

Some va lues in the Data mode “Past records” have been reset.

Did you change any date in the past according to “Setting the clock/date”?

Some values for the year, month, or week are deleted according to the relevant changes. For details, see page 48.

Page 71

ENG-70

Trouble on operation

Trouble Check Items Remedy

Press ing and holding the MODE1 or MODE2 bu tton does not turn on a light.

Che ck whe ther th e Setu p mode is displayed (page 49).

The backlight does not turn on in the Setup mode.

Check whether

lights up

on the wristwatch screen.

The remaining battery capacity of the wristwatch is low. Replace it with a new battery (CR2430). After replacement, be sure to perform the restarting operation (page 14).

Pres sing the SSS butt on does not sta rt/stop measurement.

Check whether the auto-mode is turned on (with

illumi-

nating).

When the auto-mode is on (

icon appears), you cannot start or stop the measurement by pressing the button. To start/stop measurement by pressing the SSS button, switch the automode to off (page 58).

The heart rate sensor (speed sensor) ID check failed.

The battery for th e h eart rate sensor (speed sensor) is possibly depleted. After replacing the battery with a new one (CR2032), check the sensor ID again (page 53).

Lap data cannot be stored. Check whether “--” appears

for the Lap No. screen.

The data volume exceeds the wristwatch memory capacity. Delete the ﬁles (page 45).

When using the optional “USB communication * kit”, delete the ﬁles after you send the saved ﬁles to your PC.

Does the lap time exceed 100 hours (or the interval distance exceed 9999.99 km/mile) ?

Laps cannot be measured, if recordable range described on the left is exceeded. Reset the data (page 27), and then perform measurement again.

Is it immediately after pressing the LAP button?

Recording laps needs at least 5 seconds of interval.

Abnormal values appear.

Are there any objects emitting electromagnetic waves (railway tracks, transmitting stations for television, etc.) nearby?

Keep the unit away from any object that may be causing interference, and reset the data (page

27).

Any setting cannot be changed in Option mode or Setup mode.

Is it during measurement? Settings can be only viewed during the measure-

ment.

Check whether the auto-mode is on (

lights up).

When the auto-mode is on (

lights up), the wristwatch may enter measurement mode due to electromagnetic waves. Keep the unit away from any object that may be causing interference with electromagnetic waves.

Check whether “DATA RESET” is displayed.

To change the target heart rate zone, measurement unit, and record interval, the resetting operation is required. Stop the measurement, and perform the resetting operation (page 27).

The record data in the File view cannot be viewed to the end.

Check whether “MEMORY FULL” is displayed on the screen during measurement.

The data volume exceeds the wristwatch memory capacity. The data was saved automatically during measurement, and any subsequent data was no longer recorded. D elete t he ﬁles for subsequent measurement (page 45).

When using the optional “USB communication * kit”, delete the ﬁles after you send the saved ﬁles to your PC.

Page 72

ENG-71

Continue

Water resistance of the wristwatch

The wristwatch is water-resistant up to 100 feet (30 meters). Refer to the following for proper use.

Before aquatic and outdoor activities

Caution:

The heart rate sensor and speed sensor are waterproof, but should not be used for UÊ

underwater activities.

Wash with pure water and wipe off any salt and dirt, after using in seawater or outdoors.UÊ

Do not press any button when wet.UÊ

Waterproof Capability

Rain, splash, etc.

Shower (hot water, and cold water)

Mild swimming (water depth: shallow)

Diving, surﬁng, and other marine sports (water depth: shallow)

NO!

Snorkeling (water depth: deep)

NO!

Replacing battery

The Q3a comes with factory-installed batteries. When a battery is empty, replace it with a new one according to the following instructions.

Warning!!!:

Safely dispose of the old batteries, and do not place them within reach of children. If a battery is swallowed, consult a doctor immediately.

When any battery for the wristwatch, heart rate sensor, or speed sensor is depleted, * we recommend replacing all batteries at the same time. The battery life shown in this manual is not deﬁnitive and it varies depending on the * use environment. The battery cover sealing is critical to maintain the waterproof feature. When the battery * cover and the o-ring are dirty, wipe off carefully and check that it is installed properly.

Page 73

ENG-72

Wristwatch

Battery life: Approx. 1 year when used for 1 hour per day.

When the remaining battery capacity is low, *

lights up.

Open the battery cover of the wristwatch using a coin, etc.

Turn the inner cover to the open position using

a coin, remove this, and insert a new lithium battery (CR2430) with the (+) side up.

Do not turn the inner cover excessively. * Otherwise, the tab may be damaged.

Turn the inner cover to the closed position.

Check that the cut-out portion of the inner cover faces the pin, and the 2 tabs are ﬁxed.

Press the AC button beside the inner cover using a tool with a pointed tip.

Check that an o-ring is installed to the

groove on the wristwatch, and ﬁrmly close the battery cover.

After replacement, be sure to perform the

restarting operation (page 14) to set the current time and date.

Heart rate sensor

Battery life: Approx. 1 year when worn for 1 hour per day.

Remove the battery cover on the back of the heart rate sensor using a coin, or the equivalent.

Insert new lithium batteries (CR2032) with the (+) sign

upward, and close the battery cover ﬁrmly.

The heart rate sensor consumes power when worn. Remove the * heart rate sensor whenever measurement is not performed.

Speed sensor

Battery life: Approx. 1 year when used for 1 hour per day.

Remove the battery cover on the speed sensor using a coin, or the equivalent.

Insert new lithium batteries (CR2032) with the (+) sign

upward, and close the battery cover ﬁrmly. After replacing batteries, be sure to check that the posi-

tions of the magnet and sensor are correct and they are secured ﬁrmly.

CR2032

Open

CR2032

Open

O-ring

AC button

Battery cover

Inner cover

Tab

Cut-out portion

CR2430

Open position

Closed position

Open

Page 74

ENG-73

Continue

Regularly perform the following instructions to prolong the life of your Q3a.

Regularly check that the positions of the magnets and sensors are correct, and they UÊ

are secured ﬁrmly.

When the wristwatch, heart rate sensor, and speed sensor are dirty, wash them with UÊ

water or wipe them with a soft cloth dampened with diluted neutral detergent, then wipe with dry cloth. Do not use solvents such as benzine or rubbing alcohol as they may damage the surfaces.

The heart rate strap absorbs sweat easily, and leaving it as such is unsanitary. Wash UÊ

with neutral detergent and keep it clean.

Maintenance

Spare accessories

Standard accessories

Optional accessories

#240-0570

Parts kit

#160-2385N

Speed sensor kit

#160-2395

HR Strap

#169-9691

Wheel magnet

#240-0590

USB communication kit (included with the Windows version of e-Train Data™)

#169-9766

Cadence magnet

#166-5150

Lithium-battery (CR2032) for sensors

#240-0580

Lithium-batter y (CR2430) for wristwatches

#160-2390N

Heart rate sensor kit

#240-0575

Bracket Handlebar-mount

Page 75

ENG-74

Flow of the screen

Average speed

Average

heart rate

Average

cadence

Elapsed time

ALARM

Setting the alarm clock

Current speed

Heart rate Cadence

Training function*

SOUND

Setting sound

Current speed

Heart rate Cadence

Elapsed time

CLOCK DATE

Setting the clock/date

SPORTS MENU

SETUP MENU

PC LINK

PC link

HR ZONE

Setting the target

heart rate zone

FILE

File view

CD.TIMER

Setting the training

function

DATA MENU

OPTION MENU

CLOCK MENU

Day of the week

Clock

Date

Altitude

Temperature

Current speed

Heart rate Cadence

Trip distance

ALT

Correcting the sea level

altitude

Clock mode

Sports mode

Setup mode

Option mode

Data mode





Page 76

ENG-75

Continue

MODE2

MODE1



Maximum speed

Maximum

heart rate

Maximum

cadence

Elapsed time

TIRE

Setting the tire

circumference

Current speed

Heart rate Cadence

Lap timer

AUTO MODE

Setting the auto-mode

Altitude

Heart rate Temperature

Elapsed time

SYNC ID

Setting the sensor ID

Ascending altitude

Heart rate Slope angle

Elapsed time

Current speed

Heart rate Cadence

Calorie Consumption

TOTAL DATA

Total trip distance/total

elapsed time entry

Current speed

Heart rate Cadence

Clock

UNITS

Setting the measurement unit

SAMPLE RATE

Setting the

record interval

VIEW LOG

Log data

(press & hold)

MODE1

MODE2

MENU MENU M1 M1 M2 M2

Training function: Displays one of the following: countdown distance, countdown time, and * interval.

Page 77

ENG-76

Measurement function

Upper display

Current speed

0.0 (4.0) – 150.0 km/h

0.0 (3.0) – 93.0 mph] (For 27-inch tire size) Average speed 0.0 – 150.0 km/h [0.0 – 93.0 mph] Maximum speed 0.0 (4.0) – 150.0 km/h [0.0 (3.0) – 93.0 mph] Altitude -500 – 9000 m [-1640 – 29600 ft] Ascending altitude 0 – 99999 m [ft] Average lap speed 0.0 – 150.0 km/h [0.0 – 93.0 mph] Maximum lap speed 0.0 (4.0) – 150.0 km/h [0.0 (3.0) – 93.0 mph] Middle display Heart rate 0 (30) – 240 bpm Average heart rate 0 – 240 bpm Maximum heart rate 0 (30) – 240 bpm Average lap heart rate 0 – 240 bpm Maximum lap heart rate

0 (30) – 240 bpm Cadence 0 (20) – 199 rpm Average cadence 0 – 199 rpm Maximum cadence 0 (20) – 199 rpm Average lap cadence 0 – 199 rpm Maximum lap cadence

0 (20) – 199 rpm Temperature -10 – +50 ˚C [+14 – +122 ˚F ] Slope angle 0 – ±99 % (100 % = 45°) Lap number 01 – 99 Lower display Elapsed time 0:00’00”0 – 0:59’59”9 / 1:00’00” – 99:59’59” Trip distance 0.00 – 9999.99 km [mile] Countdown distance 9999.90 – 0.00 km [mile] (setting range : 9999.9 – 0.0 km [mile]) Countdown time 99:59’00” – 0:00’00” (setting range : 99:59’ – 0:00’)

Interval timer

99:59’59” – 1:00’00” / 0:59’59”9 – 0:00’00”0

(setting range : 99:59’59” – 0:00’00”) Recovery time 0:00’00”0 – 0:59’59”9 / 1:00’00” – 99:59’59” Lap timer 00’00”0 – 0:59’59”9 / 1:00’00” – 99:59’59” Calorie consumption 0 – 999999 kcal (calculation-based estimation only)

Clock

0:00’00” – 23:59’59” [AM 1:00’00” – PM 12:59’59”]

(Both 12 and 24-hour modes can be selected) Date 00.01.01 – 99.12.31 (display format can be switched) Lap time 00’00”0 – 0:59’59”9 / 1:00’00” – 99:59’59” Split time 00’00”0 – 0:59’59”9 / 1:00’00” – 99:59’59” Lap (With the real time lap function) Lap display:

Upper display (average lap speed, maximum lap speed) Middle display (average lap heart rate, lap number, maximum lap heart rate) Lower display (lap time, split time)

Real time lap display:

Upper display (average lap speed, maximum lap speed) Middle display (average lap heart rate, maximum lap heart rate, cadence) Lower display (lap timer, lap distance)

Speciﬁcations

Page 78

ENG-77

Continue

Interval Upper display (current speed, average speed, and maximum speed) Middle display (current heart rate, average heart rate, maximum heart rate, current cadence,

average cadence, and maximum cadence)

Lower display

(interval time, number of intervals, trip distance in an interval, and recovery time)

Saving the data

Saves the data at the time of resetting (The oldest ﬁle will be deleted automatically when exceeding 30 ﬁles) (The oldest ﬁle will be deleted and the data during the measurement will be saved automatically when “MEMORY FULL” is displayed.)

Control system

8 bit one-chip microcomputer, crystal oscillator

Display system

Liquid crystal display (EL backlight)

Speed/Cadence sensor signal detection system

Noncontact magnetic sensor

Sensor signal transmission and reception

2.4 GHz ISM Band (With ID. Two IDs of SP1 and SP2 can be set for the speed sensor.)

Sensor coverage distance

5 m (above 5 m, transmission distance may vary due to environmental conditions)

Operating temperature range

32 °F – 104 °F [0 °C – 40 °C] (This product will not function appropriately when exceeding the working temperature range. Slow response or black LCD at lower or higher temperature may happen respectively.)

Storage temperature range

-4 °F – 122 °F [-20 °C – 50 °C]

Wheel circumference set range

0100 to 3999 mm: 1 size for each speed sensor ID (default setting: SP1 = 2096, SP2 = 2050)

Power supply/battery life

Wristwatch : CR2430 x 1 / Approx. 1 year (When using 1 hour/day) Heart rate sensor : CR2032 x 1 / Approx. 1 year (When worn about 1 hour per day) Speed sensor : CR2032 x 1 / Approx. 1 year (When using 1 hour/day)

Dimensions/Weight

Wristwatch : 55.0 x 46.5 x 15.0 mm (excluding the projection and belt) / 56.4 g (With

batteries)

Heart rate sensor : 12-13/16” x 1-1/4” x 1/2” (325.0 x 31.4 x 12.2 mm) / 1.41 oz (40 g) (With

batteries)

Speed sensor : 2-9/16” x 3-9/16” x 9/16” (65.0 x 90.5 x 14.4 mm) / 1.25 oz (36 g)

(With batteries)

When the elapsed time exceeds 100 hours, or the trip distance exceeds 9999.99 km/h, “* E” appears in place of the average speed.

When the elapsed time exceeds 100 hours, “* E” appears in place of the average heart rate and average cadence. Designs and speciﬁcations are subject to change without notice, due to modiﬁcations or improvements.*

Page 79

ENG-78

CATEYE Web Site (http://www.cateye.com)

For warranty service you must register your product. Please register your Q3a as soon as possible. CATEYE provides regular technical support and new product information as much as possible. Please register on-line through the “Support” page on our web site. You will need the product’s 7 -digit number (marked on the battery cover) to register your product.

Limited warranty

2-Year: wristwatch, heart rate sensor and speed sensor (Not including depletion of batteries)

CatEye products are warranted to be free of defects from materials and workmanship for a period of two years from original purchase. If the product fails to work during normal use, CatEye will repair or replace the defect at no charge. Service must be performed by CatEye or an authorized retailer. To return the product, pack it carefully and enclose the warranty certiﬁcate (proof or purchase) with instruction for repair. Please write or type your name and address clearly on the warranty certiﬁcate. Insurance, handling and transportation charges to CatEye shall be borne by person desiring service. For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory rights.

Registration

.,LTD.

Service & Research Address for USA: CatEye North America

2300 Central Ave Suite L Boulder, CO 80301 Phone: 303.443.4595 Fax: 303.473.0006 Toll Free: 800.5CATEYE E-mail: service@cateye.com URL: http://www.cateye.com

Japan Ofﬁce:

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn: CATEYE Customer Service Section

Page 80

ENG-79

Continue

Index

2.4 GHz digital wireless system .........6

Accessories........................................ 8

Alarm clock mode ............................ 24

Altitude measurement........................6

Automatic recognition of the

speed sensor ID.................................7

Auto-mode

(automatic measurement)................ 26

Backlight .......................................... 23

Basic knowledge of the altitude

measurement...................................61

Bicycle Installation ........................... 10

Clock mode (CLOCK) .......................24

Communication between your PC

and this unit.....................................46

Correcting the sea level altitude

(ALT)................................................ 60

Countdown distance ........................32

Countdown time............................... 32

Data mode (DATA)...........................39

Data to be sent from this unit to

your PC............................................47

Deleting ﬁles ....................................45

Display data in Sports mode ...... 28, 29

File view (FILE) ................................40

Flow of the screen............................ 74

Formatting .................................14, 21

Heart rate sensor .............................13

Heart rate training ............................ 63

HOME (home altitude setting).......... 61

Interval............................................. 33

Interval time..................................... 33

Lap function..................................... 30

Lap time........................................... 31

Limited warranty..............................78

Maintenance..................................... 73

Manual measurement ......................27

Memory point ..................................41

Operation test ..................................19

Option mode (OPTION).................... 36

Pace function ................................... 30

Past records (VIEW LOG) ................47

PC link (PC LINK)............................. 45

Power-saving mode ......................... 23

Preparing the wristwatch .................14

Real time lap data ............................31

Recovery time..................................33

REF (sea level altitude correction) ...61

Registration .....................................78

Replacing battery ............................. 71

Resetting.......................................... 27

Page 81

ENG-80

Restarting ..................................14, 21

Saving and managing the ﬁles .........40

Screen display.................................... 9

Searching for sensor ID (SYNC ID)

... 53

Setting sound (SOUND)...................59

Settings to be changed from your PC

... 47

Setting the alarm clock (ALARM)..... 51

Setting the auto-mode

(AUTO MODE).................................. 58

Setting the clock/date

(CLOCK DATE) ................................. 50

Setting the measurement unit

(UNITS)............................................ 55

Setting the record interval

(SAMPLE RATE) ..............................56

Setting the target heart rate zones

(HR ZONE) ....................................... 37

Setting the tire circumference (TIRE)...

Setting the training function

(CD.TIMER) .....................................36

Setup mode (SETUP).......................49

Spare accessories............................ 73

Speciﬁcations................................... 76

Split time.......................................... 31

Sports mode (SPORTS)...................25

Starting/Stopping measurement ......26

Stop reminder..................................27

Switching between modes ...............22

Target heart rate zone ................35, 63

Tire circumference ........................... 17

Tire circumference reference table... 17 Total trip distance/total elapsed

time entry (TOTAL DATA) ................57

Training for competition................... 66

Training function.............................. 32

Transmission sleep mode ................ 23

Trouble shooting.............................. 68

Use of the target zone ...................... 67

Viewing the contents in a ﬁle ...........42

Viewing the lap data......................... 44

Water resistance ..............................71

Wristwatch memory capacity limit... 40

Page 82

Please fill with 7-digits numbers marked on the battery cover of main unit.

リストウォッチ裏面のバッテリーカバーに記載の7桁の数字をご記入ください。

Veuillez indiquer le numéro à 7 chiffres indiqué sur le couvercle de la pile de l’unité principale.

Geben Sie bitte die siebenstellige Nummer an, die auf der Batterieabdeckung der Haupteinheit steht.

Vul de 7-cijferige nummers in die op de batterijendeksel van de computer staan.

Por favor, complete el número de 7 dígitos mostrado en la tapa de las pilas de la unidad principal).

Inserire il codice di 7 cifre indicato sul coperchio del vano batterie dell’unità principale.

請填入手錶後蓋上刻印的7位數字。

请填入手表后盖上刻印的7位数字。

INTERNATIONAL WARRANTY CERTIFICATE

CERTIFICAT DE GARANTIE INTERNATIONALE INTERNATIONALES GARANTIEZERTIFIKAT

INTERNATIONAAL GARANTIECERTIFICAAT CERTIFICATO DI GARANZIA INTERNAZIONALE CERTIFICADO DE GARANTÍA INTERNACIONAL

保証書

国际保固证明书國際保固證明書

Your name address or e-mail address will not be sold or shared with any other company.

ご送信いただいた情報や内容の管理には万全を期し、新製品情報やテクニカルサポート提供以外に使用することは一切ありません。

Votre adresse postale et votre adresse e-mail ne seront pas vendues ou transmises à d’autres entreprises. Ihr Name oder Ihre E-Mail-Adresse wird weder weiterverkauft noch an eine andere Firma weitergegeben. Uw naam, adres of e-mailadres zullen niet beschikbaar worden gesteld aan derden. Su nombre, dirección o correo electrónico no serán vendidos o compartidos con otras empresas. IIl vostro nome, indirizzo o indirizzo e-mail non saranno venduti o condivisi con altre società.

顧客情報內容將被妥善管理，只會使用在提供新產品信息及技術支援上。

顾客情报内容将被妥善管理，只会使用在提供新产品信息及技术支援上。

Serial No

シリアルNo

No. de série Seriennr Serienummer Nº de serie

Numero di matricola

產品編號

产品编号

Name

お名前(フリガナ)

Nom Name Naam Nombre

Nome

姓名

Address

ご住所

Adresse Adresse Adres Dirección

Indirizzo

地址

E-mail address

Eメールアドレス

Adresse e-mail E-mail-Adresse E-mailadres Dirección de correo electrónico

Indirizzo e-mail

郵箱地址

邮箱地址

Phone

電話番号

Téléphone Telefon Telefoon Teléfono

Numero di telefono

電話號碼

电话号码

Dealer or Shop name

ご購入店名

Nom du magasin ou du revendeur Name des Händlers oder des Geschäfts Dealer of Naam van winkel Nombre del proveedor o de la tienda

Nome del punto vendita

經銷商名

经销商名

Dealer or Shop address

所在地

Adresse du magasin ou du revendeur Adresse des Händlers oder des Geschäfts Dealer of Adres van winkel Dirección del proveedor o de la tienda

Indirizzo del punto vendita

經銷商地址

经销商地址

The date of purchase

ご購入日

Date d’achat Kaufdatum Datum van aankoop Fecha de compra

Data di acquisto

購入日期

购入日期

REGISTRATION CARD

ユーザー登録カード

Fiche d’enregistrement Registrierungskarte

Registratiekaart Tarjeta de registro

Scheda di registrazione

用戶登記卡用户登记卡

PURCHASER'S NAME/ADDRESS

NOMBRE/DIRECCIÓN DEL COMPRADOR NOME/INDIRIZZO DEL COMPRATORE

NAAM/ADRES KOPER

NAME UND ANSCHRIFT DES KÄUFERS

NOM/ADRESSE DU CLIENT

DEALER'S NAME/ADDRESS

NOMBRE/DIRECCIÓN DEL DISTRIBUIDOR NOME/INDIRIZZO DEL VENDITORE

NAAM/ADRES VERKOPER

NAME UND ANSCHRIFT DES HÄNDLERS

NOM/ADRESSE DU DISTRIBUTEUR

DATE OF PURCHASE

FECHA DE COMPRA DATA DELL’ ACQUISTO

AANKOOPDATUM

VERKAUFSDATUM

DATE D’ACHAT

ご住所・お名前

购买者的姓名／地址購買者的姓名地址

販売店名・住所

经销商的姓名／地址經銷商的姓名地址

お買い求め年月日

购买日期購買日期

U.S. Pat. Nos. and Design Pat. Pending

MSCCY3-100816

Page 83

066600810 CY300ENG 1

CATEYE C 0., LTD 2-8-25 , KU WAZU, HIGASHI SUMIYOSHI-KU, OSAKA, JAPAN 546-0041

www.cateye.com www.cateye.co.jp

Page 84

CATEYE USBCU, CY300 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual