
VEGA9300
User’s Manual
V0.3
Version: 0.3
Date: July 20,2005
Castles Technology Co., LTD.
Tel: 886 (2) 8913-1771
Fax: 886 (2) 8913-1772
E-Mail: casauto@casauto.com.tw
Web: www.casauto.com.tw
© Castles Technology Co., LTD. 2004
All rights reserved

VEGA9300 User's Manual V0.3
WARNING
Information in this document is subject to change without prior notice.
No part of this publication may be reproduced, transmitted, stored in a retrieval
system, nor translated into any human or computer language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise, without the prior written permission of Castles Technology Co., LTD.
All trademarks mentioned are proprietary of their respective owners.
Note:
1. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
2. This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are desi gned to provide
reasonable protection against harmful interference in a residential inst allation. This
equipment generates, uses and can radiate radio frequency energy and, if not inst alled and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause ha rmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures
a. Reorient or relocate the receiving antenna.
b. Increase the separation between the equipment and receive r.
c. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
d. Consult the dealer or an experienced radio/TV technician for help.
e. Reorient or relocate the receiving antenna.
f. Increase the separation between the equipment and receiver.
g. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
h. Consult the dealer or an experienced radio/TV technician for help.
Castles Automation Co., Ltd. All rights reserved. 2/11

VEGA9300 User's Manual V0.3
Table Of Contents
WARNING........................................................................................................2
1. Introduction .................................................................................................4
1.1 Front View..................................................................................4
1.2 Side View ...................................................................................5
1.3 Head View..................................................................................5
1.4 Back View...................................................................................6
1.5 Magnetic Stripe Card Reader & Smart Card Introduction...........7
1.6 Handset and the Base Connection.............................................8
1.6.1 Pull Out ...............................................................................8
1.6.2 Pull Back.............................................................................8
1.7 Rechargeable Battery Installation...............................................8
1.8 SAM Card Installation.................................................................9
1.9 Paper Roll Installation...............................................................10
1.10 Power.......................................................................................11
Castles Technology Co., Ltd. All rights reserved.
3/11

1. Introduction
1.1 Front View
Paper Roll Box
VEGA9300 User's Manual V0.3
Power Key
F1 Key
LED (Green)
LED (Orange)
LED (Red)
1. Power Key:Power On- Press Power Key 3 Second To Start.
Press Off- Press Power Key To Turn Off
2. F1 Key:Press F1 To The Download Main Menu To Enter The Download
Mode Under The Program Manager Screen. Press Cancel Key Will Go
Back To The Program Manger Screen.
3. F2 Key、F3 K ey:Press F2 or F3 Key To Select The Program When There
F2 Key
F3 Key
F4 Key
Cancel Key
Clear Key
Enter Key
Are Many Applications In The Program Manager Screen.
4. F4 Key:Press F4 To Execute The Selected Program.
Castles Technology Co., Ltd. All rights reserved. 4/11