Casio TMR-200 User Manual

MA0212-A

USER’S GUIDE TMR-200

Battery compartment cover

5-compartment case

• A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the clock.

• Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the illustration.

ALARM OFF

ALARM ON

Reminder alarm times (Hour, minutes) Reminder alarm number

No.1 ALARM ON (6:00) No.2 ALARM ON (9:30) No.3 ALARM OFF (–:––) No.4 ALARM OFF (–:––) No.5 ALARM ON (PM8:00)

Day of the week

PM indicator

Alarm on indicator

GENERAL GUIDE

1 SNOOZE/LIGHT button

• Press to illuminate the display for a few seconds.

• Press to stop the alarm.

2 HR/MONTH button

Press to advance the hour or month digits during time/date setting.

3 MIN/DATE button

Press to advance the minute or date digits during time/date setting.

4 YEAR/5-AL ON/OFF button

• Press to advance the year digits during date setting.

• Press to turn a reminder alarm on or off.

5 5-AL. SET button

Use this button to start a reminder alarm time setting operation.

6 SET button

Press to cycle through setting screens.

7 RESET button

Press this button to reset the clock after changing batteries.

8 Alarm Mode selector

SET: Alarm time setting ON: Alarm on OFF: Alarm off

9 Alert Mode Selector

BEEP: Beep alert VIB: Vibration alert BEEP & VIB: Both beep and vibration alert

DATE (month - date)

Current time (Hour, minutes, seconds)

Vibration alert ON indicator

Beep alert ON indicator

Daily alarm time (Hour, minutes)

USER’S GUIDE TMR-200

TO SET THE TIME

1. Press the SET button (

2. Select the setting you want to change, and then use the HR/MONTH button (

(

3), and YEAR/5-AL ON/OFF button (

• Holding down any button changes its setting at high speed.

• You can set the year in the range of 2000 to 2039. The day of the week is set automatically in

accordance with the date setting.

• Pressing HR ( count to be reset to 00.

3. After configuring the settings you want, use the SET button ( Screen.

• The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on

the display for about three minutes without performing any operation.

6) to cycle through the setting screens as shown below.

Normal Timekeeping Screen

Time Setting Screen Date Setting Screen

4) to change it.

2) or MIN (

3) while the Time Setting Screen is on the display causes the seconds

6) to display the Normal Timekeeping

2), MIN/DATE button

USING THE ALARM

• This clock has a Daily Alarm and a 5 Reminder Alarms. The following table summarizes the features of

each alarm type.

Alarm Type

Daily Alarm

5 Reminder Alarms

• For the alarm alert, you can set up the clock to use an audible beeper or a silent vibrator, or the beeper

and vibrator in combination.

• When an alarm is set and turned on, it performs the specified alert operation each day at the specified

time. Pressing any clock button stops an ongoing alert operation.

• Note that the Daily Alarm is a snooze alarm. This means that the alert operation is repeated about five

minutes after you stop it. To completely stop the Daily Alarm so it does not sound again, slide the Alarm

Mode selector (

To set the Daily Alarm time

1. Slide the Alarm Mode selector ( the display.

2. Press HR ( either button changes its setting at high speed.

3. After you set the alarm time, slide the Alarm Mode selector (

• An alarm does not sound if its alarm time is reached while an alarm setting screen is on the display.

SNOOZE Alarm

Yes

8) to OFF.

2) to increase the hour setting and MIN (

Alert Duration

1 minute (repeats 7 times every five minutes)

30 seconds

8) to SET. This causes the current daily alarm time setting to flash on

3) to increase the minute setting. Holding down

8) to OFF or ON.

To turn the Daily Alarm on and off

Slide the Alarm Mode selector (

• Turning on the Daily Alarm causes the indicator to appear at the bottom of the display. Also, the Daily Alarm time setting appears in the upper part of the display in place of the current date. While the Daily Alarm is turned on, you can view the current month and day by holding down the HR/MONTH

button (

2), MIN/DATE button (

To set the 5 Reminder Alarms

1. Press the 5-AL.SET button (

• This causes the setting of Reminder Alarm ( ) to flash.

2. Press HR (

3. Press the 5-AL.SET button (

4. Repeat steps 2 and 3 to set the other Reminder Alarm times.

5. When Reminder Alarm ( ) is flashing, press the 5-AL.SET button (

To turn the 5 Reminder Alarms On and Off

1. Press the 5-AL.SET button (

2. Press the 5-AL.SET button (

3. Press the 5-AL ON/OFF button (

4. When Reminder Alarm ( ) is flashing, press the 5-AL.SET button (

Selecting the Alert Mode

• Use the Alert Mode selector ( all of the 5 Reminder Alarms.

For this type of alert:

Beep Vibration Beep + Vibration

2) to increase the hour setting and MIN (

either button changes its setting at high speed.

• This causes the setting of the next Reminder Alarm to flash.

Timekeeping Screen.

• This causes the setting of Reminder Alarm ( ) to flash.

displayed) and off (–:–– displayed).

Timekeeping Screen.

8) to ON to turn the Daily Alarm on, or OFF to turn it off.

3), or YEAR/5-AL ON/OFF button (

5) until the setting of Reminder Alarm ( ) starts to flash.

3) to increase the minute settings. Holding down

5) to move the flashing to the next Reminder Alarm ( ).

5) until the setting of Reminder Alarm ( ) starts to flash.

5) to move the flashing to the Reminder Alarm you want to turn on or off.

4) to toggle the flashing alarm on (current alarm time setting

9) to select the alert mode you want to use for the Daily Alarm and for

Select this setting:

BEEP VIB BEEP&VIB

Which is indicated by the display indicator:

4).

5) to return to the Normal

TO ILLUMINATE THE DISPLAY

Press SNOOZE/LIGHT button (

Important!

• Overuse of the light can shorten battery life.

1) to illuminate the display for about three seconds.

BATTERY REPLACEMENT

Replace batteries whenever the display of the clock becomes dim and difficult to read.

1. Open the battery compartment cover as shown in the illustration.

2. Remove both old batteries.

3. Load new batteries. Make sure that their positive (+) and negative (–) ends face in the correct

directions. If you load batteries incorrectly, they can burst and damage the clock.

4. Replace the battery compartment cover.

5. Press the RESET button (

Battery precautions

• Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your physician immediately.

• Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.

• Never mix old and new batteries, or batteries of different brands.

• Never charge the batteries that come with the clock.

• Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get

onto your skin.

• Replace the batteries at least once a year, even if the current batteries are working properly.

• The batteries that come with the clock lose some of their power during transport and storage.

7). Be sure to press the RESET button (

7) after replacing batteries.