Casio MONTRE DATA-BANK User Manual
Module No. 2700
Current
digital time
Mode
indicator
2700-1
• Button operations are indicated using the letters shown in the illustration.
• Depending on the model of your watch, display text appears either as dark figures on a light background (positive), or light figures on a dark background
(negative). All sample displays in this manual are shown in positive.
• For the sake of simplicity, the sample displays in this manual do not show the analog hands of the watch.
• Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can be
found in the “REFERENCE” section.
If the digital display of your watch is continuously changing, press any button other than B to stop it. See “Auto Display” for more information.
GENERAL GUIDE
• Press C to change from mode to mode. Changing to another mode causes one of a number of different animations to be performed on the display.
• In any mode, press B to illuminate the display.
ABOUT THIS MANUAL
Timekeeping
Mode
Press .
Use the Timekeeping Mode to set and view the current time and date.
• In the Timekeeping Mode, press A to change the display format as shown below.
World Map Seconds
Hour hand
• The analog screen does not show the alarm on indicator, DST indicator, or any other
digital display information.
• Pressing D while any of the above screens is on the display momentarily displays
the current time and then the current date in the cycle shown below.
Press .
PM indicator
Read This Before You Set the Time and Date !
The digital times displayed in the Timekeeping Mode and World Time Mode are
linked. Because of this, make sure you select a city code for your Home City (the city
where you normally use the watch).
• This watch features separate digital and analog timekeeping. Note that the digital
time and analog time are independent of each other, and must be set separately.
To set the digital time and date
3. When the setting you want to change is flashing, use D and B to change it as
described below.
To change this setting Perform this button operation
Seconds Press D to reset to 00.
DST
12/24-Hour Format
City Code, Hour, Minutes,
Year, Month, Day
• See “CITY CODE TABLE” for a complete list of available codes.
• Pressing D while the second’s count is in the range of 30 to 59 resets the
seconds to 00 and adds 1 to the minutes. In the range of 00 to 29, the minute’s
count is unchanged.
• See “Daylight Saving Time (DST)” for details on DST setting.
4. Press A to exit the setting screen.
World Time
Mode
Data Bank
Mode
TIMEKEEPING
Press .
Analog
Minute hand
Seconds
Hour : Minutes
1. In the Timekeeping Mode, hold down A until the
second’s digits start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
City
Month
DST
Code
Year
Seconds
Day
Press D to toggle between Daylight Saving Time (On)
and standard time (OF).
Press D to toggle between 12-hour (12H) and
24-hour (24H) timekeeping.
Use D (+) and B (–) to change the setting.
Fireworks
Day of week
Month – Day
Hour
12/24-Hour
Format
Minutes
Alarm 1
Mode
Note
• Resetting the seconds only (without changing the hour or minute setting) causes the
analog minute hand setting to be adjusted automatically. If you change the hour or
minute setting, you should also use the procedure under “To adjust the analog time”
to adjust the analog hands accordingly.
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
• The year can be set in the range of 2000 to 2039.
• The watch’s built-in full automatic calendar automatically makes allowances for
different month lengths and leap years. Once you set the date, there should be no
reason to change it except after you have the watch’s batteries replaced.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
Analog Timekeeping
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
When you want to do this:
Move the hand setting forward 20 seconds.
Move the hand setting a short way forward
at high speed.
Move the hand setting a long way forward at
high speed.
4. Press A to exit the setting screen.
• To return to the Timekeeping Mode, press C.
Alarm 2
Mode
1. In the Timekeeping Mode, hold down A until the
second’s digits start to flash, which indicates the setting
screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (On
displayed) and standard time (OF displayed).
4. Press A to exit the setting screen.
• The DST indicator appears on the display to indicate
that daylight saving time is turned on.
1. In the Timekeeping Mode, press C six times to enter
the Analog Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the setting screen.
• Analog timekeeping is suspended while the analog
setting screen is on the display.
3. Use D and B to adjust the analog setting as
described below.
• The hands move clockwise only. They cannot move
counterclockwise.
Stopwatch
Mode
Perform this button operation:
Press D.
• Hold down D.
• Release D when the hands reach the
setting you want.
• While holding down D to move the hands
at high-speed, press B to lock the highspeed hand movement.
• Press any button when the hands are
close to the setting you want.
• Hand movement stops automatically if the
hour hand makes one full (12-hour)
revolution.
Analog Setting
Mode
2700-2
e
r
World Time shows the current time in 50 cities (27 time zones) around the world.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C.
To view the time in another city code
In the World Time Mode, press D to scroll forward through the city codes.
City code
Mode
indicator
• Selecting a city code causes the NOC code screen to appear first, followed a short
time later by the time screen.
• NOC codes are the abbreviations designating the National Olympic Committee for
each geographic area (as of December 2000).
• For full information about city codes, see the “CITY CODE TABLE”.
• If the current time shown for a city is wrong, check your Timekeeping Mode time and
Home City code settings and make the necessary changes.
To toggle World Time Mode times between standard time and Daylight Saving Time
NOC Code Time
NOC code
In the World Time Mode, hold down A for about two
seconds to toggle between Daylight Saving Time (DST
displayed) and standard time (DST not displayed).
• The above operation toggles all World Time city codes
Current time in the zone of the selected city cod
between Daylight Saving Time and standard time. Note
that you cannot make settings for individual city codes.
DATA BANK MODE
WORLD TIME
Name
Mode indicato
Telephone number
Remaining memory
To create a new Data Bank record
Name area
Number area
4. When the character you want is at the cursor position, press C to move the cursor
to the right.
5. Repeat steps 3 and 4 until the name is complete.
• You can input up to eight characters for the name.
6. After you input the name, press C as many times as necessary to move the cursor
to the number area.
• When the cursor is located at the eighth space of the name area, moving the
cursor to the right causes it to jump to the first digit of the number. When the
cursor is at the 16th digit of the number, moving it to the right (by pressing C)
causes it to jump to the first character in the name.
7. Use D and B to change the character (hyphen, number, space, or plus) at the
cursor position in the number area. The character changes in the following
sequence.
Press .
Press .
8. When the character you want is at the cursor position, press C to move the cursor
to the right.
9. Repeat steps 7 and 8 until you complete number input.
• You can input up to 16 digits for the number.
10. Press A to store your data and return to the Data Bank record screen (without
the cursor).
• When you press A to store data, the message “SORT” appears on the display for
a while, indicating that data is being sorted. After the sort operation is complete, the
Data Bank record screen appears.
The Data Bank Mode lets you store up to 30 records,
each containing name and telephone number data.
Records are automatically sorted based on the characters
of the name. You can recall records by scrolling through
them on the display.
• See “CHARACTER LIST” for details on how the watch
sorts records.
• All of the operations in this section are performed in the
Data Bank Mode, which you enter by pressing C.
1. In the Data Bank Mode, press B and D at the same
time to display the remaining memory screen.
• If the message “FULL” appears on the display, it
means that memory is full. To store another record,
you will first have to delete some of the records stored
in memory.
2. Hold down A until the flashing cursor (
the name area of the display, which indicates the
setting screen.
3. Use D and B to change the character at the cursor
position in the name area. The character changes in the
(space)
following sequence.
Press .
A to Z
0 to 9
Press .
(space)
) appears in
0 to 9
To recall Data Bank records
In the Data Bank Mode, press D to scroll forward through Data Bank records on the
display.
• The name and/or telephone number of the selected Data Bank record scrolls on the
Data Bank record screen. The symbol
telephone number follows next.
• Each press of A in the Data Bank Mode changes the scroll operation as shown
below.
Name scrolls
Number scrolls
To edit a Data Bank record
1. In the Data Bank Mode, scroll through the records and display the one you want to
edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use D and B to change the character.
• For details on inputting characters, see “To create a new Data Bank record” (step
3 for name input and 7 for number input).
5. After making the changes that you want, press A to store them and return to the
Data Bank record screen.
To delete a Data Bank record
1. In the Data Bank Mode, scroll through the records and display the one you want to
delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the record.
• The message “CLR” appears to indicate that the record is being deleted. After
the record is deleted, the cursor appears on the display, ready for input.
4. Input data or press A to return to the Data Bank record screen.
indicates the first character of the name or
Name stops
Number scrolls
Name scrolls
Number stops
ALARMS
This watch has two alarms (Alarm 1 and Alarm 2), for
which you can make separate hour, minute, and day of
the week settings.
When an alarm is turned on, the alarm tone sounds when
the alarm time is reached by the Timekeeping Mode
digital time.
• Use the Alarm 1 and Alarm 2 Modes to set alarms. You
can enter an Alarm Mode using C. The setting
Mode indicator
Alarm Types
The alarm type is determined by the settings you make, as described below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
• Weekly Alarm
Set the hour, minutes, and the day of the week for the alarm time. This type of setting
causes the alarm to sound every week at the time you set, on the day of the week you
set.
To set an alarm time
Day of week
Alarm time
(Hour : Minutes)
• To set an alarm that does not include a day of the week (daily alarm), set “– – –”
for the day of the week. Press D or B until the “– – –” mark appears (between
SUN and MON) while the day of the week setting is flashing.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
4. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, or until you stop it by
pressing any button.
To test the alarm
While in the Alarm 1 or Alarm 2 Mode, hold down D to sound the alarm.
To turn an alarm on and off
Alarm 1 on
Alarm 2 on
indicator
indicator
procedure is the same for both of the alarm screens.
1. After enter the Alarm 1 or Alarm 2 Mode, hold down A
until the day of the week setting starts to flash, which
indicates the setting screen.
• This operation automatically turns on the
corresponding alarm.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Day of week MinutesHour
3. While a setting is flashing, use D (+) and B (–) to
change it.
1. Enter the Alarm Mode (Alarm 1 or Alarm 2) you want to
turn on or off.
2. Press D to toggle the alarm on (alarm time displayed)
and off (OFF displayed).
• The Alarm 1 on indicator indicates that Alarm 1 is on,
while the Alarm 2 on indicator indicates Alarm 2 is on.
• Alarm on indicators are displayed in all modes.
Loading...