Casio MO0706-EA User Manual

MO0706-EA

Operation Guide 4766

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully.

••

• This watch does not have a city code that corresponds to the Greenwich

••

Mean Time differential of –3.5 hours. Because of this, the radio-controlled atomic timekeeping function will not display the correct time for Newfoundland, Canada.

Keep the watch exposed to bright light

Bright light

• The watch continues to operate, even when it is not exposed to light. Leaving the watch in the dark can cause the battery to run down, which will cause some watch functions to be disabled. If the battery goes dead, you will have to re-configure watch settings after recharging. To ensure normal watch operation, be sure to keep it exposed to light as much as possible.

Battery charges in the light. Battery discharges in the dark.

Solar cell (Converts light to electrical power.)

Charge

The electricity generated by the solar cell of the watch is

stored by a built-in battery. Leaving or using the watch

where it is not exposed to light causes the battery to run down. Make sure the watch is exposed to light as much as possible.

• When you are not wearing the watch on your wrist,

Solar cell

Rechargeable battery

position the face so it is pointed at a source of bright light.

• You should try to keep the watch outside of your sleeve as much as possible. Even if the face of the watch is blocked only partially from light, charging will be reduced significantly.

Bright light

LEVEL 1

LEVEL 2

LEVEL 3

Electrical energy

All functions enabled.

All functions disabled, except for analog timekeeping and stopwatch .

charge

Dis-

LEVEL 1

LEVEL 2

LEVEL 3

All functions disabled.

• The actual level at which some functions are disabled depends on the watch model.

• Be sure to read “Power Supply” for important information you need to know

when exposing the watch to bright light.

If the analog hands aren’t moving...

If the analog hands aren’t moving, it means that the power saving mode has stopped them to save battery power.

• See “Power Saving” for more information.

• The hands also stop whenever the battery level reaches Level 3.

About This Manual

Stopwatch second hand

Hour hand

24-hour hand

Minute hand

Date

Second hand

• Button operations are indicated using the letters shown in the illustration.

• Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can be found in the “Reference” section.

Day of the week hand

General Guide

Manual Receive Receive Status Check

Hold down A

for about two seconds.

▲

Transmitter Change Time/Date Adjustment

• About 1.5 seconds after you enter the World Time Mode from the Timekeeping Mode, the watch’s hands will start to move to the time setting for the World Time Mode. All button operations are disabled while the hands are moving.

Press any button.

Hold down A for about five seconds.

▲

Press A.

▲

Press A.

Timekeeping Mode

Radio-controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly.

• Supported time calibration signals: Germany (Mainflingen), England (Rugby), United States (Fort Collins), Japan (Fukushima or Fukuoka/Saga).

• See the information under “Signal Reception Troubleshooting” if you experience problems with time calibration signal reception.

Current Time Setting

This watch adjusts its time setting automatically in accordance with a time calibration signal. You also can perform a manual procedure to set the time and date, when necessary.

• The first thing you should do after purchasing this watch is to specify your Home City, which is the city where you will normally use the watch. For more information, see “To specify your Home City”.

• When using the watch outside the areas covered by the time signal transmitters, you will have to adjust the current time setting manually as required. See for more information about manual time settings.

• The U.S. time calibration signal can be picked up by the watch while in North America. The term “North America” in this manual refers to the area that consists of Canada, the continental United States, and Mexico.

To specify your Home City

second hand

City codeStopwatch

1. In the Timekeeping Mode, hold down A for about five

seconds until the stopwatch second hand moves to the city code of the currently selected Home City. This indicates the watch is in the setting mode.

2. Use D to change the Home City setting.

• Each press of D causes the stopwatch second hand

to advance clockwise to the next city code.

• All hands (except for the second hand) and the date display will change automatically to the applicable settings for the currently selected city code. All button operations are disabled while the hands and date display are changing.

• Time calibration signal reception is supported when any one of the city codes shown in the table below is selected as your Home City.

“Timekeeping”

Press

Press D. (When the stopwatch is reset to all zeros.)

City

City Name

Code HNL

Honolulu

ANC

Anchorage Los Angeles

LAX

B or D.

Press C.

▲

City Code HKG TYO

▲

City Name

Hong Kong Tokyo

German/U.K. Signal Japan Signal U.S. Signal

City

City Name

Code LON

London

PAR

Pari s

ATH

Athens

• In addition to the above, you also can select city codes that are outside the ranges of the time calibration signal transmitters supported by this watch.

• Note that this watch does not have a city code that corresponds to Newfoundland.

3. After the Home City setting is the way you want, press A to return to the

Timekeeping Mode.

• Normally, your watch should show the correct time as soon as you specify your Home City code. If it does not, it should adjust automatically after the next auto receive operation. You also can perform manual receive or you can set the time manually.

• Even if the time calibration signal is received correctly, there are some times when the analog hands may not indicate the correct time. If this happens, use the procedures under “Adjusting the Home Positions” to check the home positions of the hands, and make adjustments as required.

• You can also change the Home City setting by swapping the current Home City and the currently selected World Time City. For details, see “Swapping your Home City and World Time City”.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time. Remember that not all countries or even local areas use Daylight Saving Time. The time calibration signals transmitted from Mainflingen (Germany), Rugby (England), or Fort Collins (the United States) include both Standard Time and DST data. When the Auto DST setting is turned on, the watch switches between Standard Time and DST (summer time) automatically in accordance with the signals.

• Though the time calibration signal transmitted by the Fukushima and Fukuoka/Saga, Japan transmitters include summer time data, summer time currently is not implemented in Japan (as of 2007).

• The default DST setting is Auto DST (AUTO/AT) whenever you select LON, PA R, ATH , ANC, LAX, DEN, CHI, NYC, or TYO as your Home City code.

• If you experience problems receiving the time calibration signal in your area, it probably is best to switch between Standard Time and Daylight Saving Time (summer time) manually. For more information, see “To set the time and date manually”.

Stopwatch ModeTimekeeping ModeWorld Time Mode

▲

City Code DEN CHI NYC

City Name

Denver Chicago New York

Operation Guide 4766

Time Calibration Signal Reception

There are two different methods you can use to receive the time calibration signal: auto receive and manual receive.

• Auto Receive

With auto receive, the watch receives the time calibration signal automatically up to six times a day. When any auto receive is successful, the remaining auto receive operations are not performed. For more information, see “About Auto Receive”.

• Manual Receive

Manual receive lets you start a time calibration receive operation with the press of a button. For more information, see “To perform manual receive”.

Important!

• When getting ready to receive the time calibration signal, position the watch as shown in the nearby illustration, with its 12 o’clock side facing towards a window. Make sure there are no metal objects nearby.

12 o’clock

• Make sure the watch is facing the right way.

• Proper signal reception can be difficult or even impossible under the conditions listed

below.

60.0 kHz

77.5 kHz

40.0 kHz

60.0 kHz

Among or behind mountains

2,000 miles (3,000 kilometers)

600 miles (1,000 kilometers)

Fort Collins

Inside or among buildings

• Signal reception normally is better at night than during the day.

• Time calibration signal reception takes from two to seven minutes, but in some

cases it can take as long as 14 minutes. Take care that you do not perform any button operations or move the watch during this time.

• The time calibration signal the watch will attempt to pick up depends on its current Home City code setting as shown below. If you use the watch in Japan or Europe (each of which has two different transmitter locations), it will try to receive the time calibration signal from one of the transmitters in your current location. If it cannot receive the signal, it will then try to receive the time calibration signal from the other transmitter.

Home City Codes and Transmitters

LON, PAR, ATH

HKG*, TYO

HNL*, ANC*, LAX, DEN, CHI, NYC

* The areas covered by the HKG, HNL, and ANC city codes are quite far from the

time calibration signal transmitters, and so certain conditions may cause problems with signal reception.

Reception Ranges

1,500 kilometers

Rugby

500 kilometers

Inside a vehicle

Home City Code

U.K. and German Signals

500 kilometers

Fukuoka/Saga

1,000 kilometers

Transmitter

Mainflingen

Near a construction site, airport, or other sources of electrical noise

Near household appliances, office equipment, or a mobile phone

Rugby (England) Mainflingen (Germany)

Fukushima (Japan) Fukuoka/Saga (Japan)

Fort Collins, Colorado (the United States)

Near hightension power lines

U.S. Signal

500 kilometers

Fukushima

1,000 kilometers

Frequency

Japan Signal

• Signal reception may not be possible at the distances noted below during certain times of the year or day. Radio interference may also cause problems with reception.

Mainflingen (Germany) or Rugby (England) transmitters: 500 kilometers (310 miles) Fort Collins (United States) transmitter: 600 miles (1,000 kilometers) Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

• Even when the watch is within the reception range of the transmitter, signal reception will be impossible if the signal is blocked by mountains or other geological formations between the watch and signal source.

• Signal reception is affected by weather, atmospheric conditions, and seasonal changes.

About Auto Receive

The watch receives the time calibration signal automatically up to six times a day. When any auto receive is successful, the remaining auto receive operations are not performed. The reception schedule (calibration times) depends on your currently selected Home City, and whether standard time or Daylight Saving Time is selected for your Home City.

Your Home City Auto Receive Start Times

LON

PAR

ATH

HKG, TYO

HNL, ANC, LAX, DEN, CHI, NYC

Note

• Auto receive is supported in all modes except while a stopwatch elapsed time operation is in progress.

• Auto receipt of the calibration signal is designed to be performed early in the morning, while you sleep (provided that the Timekeeping Mode time is set correctly). Before going to bed for the night, remove the watch from your wrist, and put it in a location where it can receive the signal easily.

• The watch receives the calibration signal for two to 14 minutes everyday when the time in the Timekeeping Mode reaches each of the calibration times. Do not perform any button operation within 14 minutes before or after any one of the calibration times. Doing so can interfere with correct calibration.

• Remember that reception of the calibration signal depends on the current time in the Timekeeping Mode.

Standard Time

Daylight Saving Time

Standard Time

Daylight Saving Time

Standard Time

Daylight Saving Time

Standard Time

Standard Time Daylight Saving Time

To perform manual receive

W(WORK)

• After signal reception is successful, the watch adjusts its hour, minute, 24-hour hand, and second hand settings, and then returns to the Timekeeping Mode. Next, the stopwatch second hand moves to Y (YES) momentarily to indicate that signal reception was successful. After about five seconds, the stopwatch second hand moves to 12 o’clock.

Note

• To interrupt a receive operation and return to the Timekeeping Mode, press any button.

• If signal reception fails for some reason, the watch returns to normal timekeeping without making any adjustments. Next, the stopwatch second hand moves to N (NO) momentarily to indicate that signal reception failed. After about five seconds, the stopwatch second hand moves to 12 o’clock.

• If the stopwatch second hand is pointing to Y (YES) or N (NO), you can return to the Timekeeping Mode by pressing any button.

Viewing the Latest Signal Reception Results

You can use the procedure below to check whether or not the last signal receive operation was successful.

R(READY)

Y(YES)

N(NO)

To check the latest signal reception results

• The current receive result is cleared when the first auto receive operation is performed on the following day. This means Y (YES) indicates successful signal reception since the start of the current day.

• If you adjust the time or date setting manually, the stopwatch second hand will move to N (NO).

Signal Reception Troubleshooting

Check the following points whenever you experience problems with signal reception.

The stopwatch second hand is pointing at N (NO).

Time setting is incorrect following signal reception.

• For further information, see “Important!” under “Time Calibration Signal Reception” and “Radio-controlled Atomic Timekeeping Precautions”.

• You changed the time setting manually. You performed some button operation

•

during the auto receive operation.

• The stopwatch is performing an elapsed time measurement operation.

• Signal reception results are reset at the first time of the next receive period.

• The Home City setting is not correct for the area where you are using the watch. The home position of the hands is off.

•

123456

1:00 am

2:00 am

3:00 am

4:00 am

5:00 am

Midnight

2:00 am

3:00 am

4:00 am

5:00 am

2:00 am

3:00 am

4:00 am

5:00 am

3:00 am

4:00 am

5:00 am

Midnight

3:00 am

4:00 am

5:00 am

Midnight

1:00 am

Midnight

1:00 am

1. Place the watch on a stable surface so its 12 o’clock side is facing towards a window.

2. In the Timekeeping Mode, hold down A for about two seconds.

3. The stopwatch second hand will move to R (READY) to indicate that the watch is setting up for time calibration reception.

• The stopwatch second hand will move to W (WORK)

and stay there while actual reception is in progress.

• The hour, minute, and 24-hour hands all continue to

keep time normally.

• The second hand will stop at “0”.

Some models show “60” instead of “0”.

• Time calibration signal reception takes from two to

seven minutes, but in some cases it can take up to 14 minutes. Take care that you do not perform any button operations or move the watch during this time.

In the Timekeeping Mode, press A.

• If the watch was able to perform a successful signal

receive operation during the last receive period, the stopwatch second hand will move to Y (YES). If the watch has been unable to receive any signal successfully, the stopwatch second hand will move to N (NO).

• The watch will return to the Timekeeping Mode after five

seconds or when you press A.

next day

5:00 am

Midnight next day

Midnight

1:00 am

next day

2:00 am

3:00 am

2:00 am

3:00 am

What you should doProblem Probable Cause

• Perform manual signal receive or wait until the next auto signal receive operation is performed.

• Stop the stopwatch operation.

• Check to make sure the watch

is in a location where it can receive the signal.

• Select the correct Home City.

•

Enter the Home Position Adjustment Mode and adjust the home position.

Midnight next day

1:00 am next day

2:00 am next day

4:00 am

next day 1:00 am

next day 2:00 am

next day 3:00 am

next day 5:00 am

5:00 am

+ 3 hidden pages