Casio ID-17 Operating Manual
MA1508-EA
© 2015 CASIO COMPUTER CO., LTD.
Wall hang hole
Operation Guide ID-17
OK
Not OK
• A sticker is affi xed to the glass of the clock when you purchase it. Be sure to remove the sticker before using
the clock.
• Depending on the clock model, its confi guration may differ somewhat from that shown in the illustration.
PM indicator
Current time
(Hour, minutes, seconds)
1342
DATE (month - day)
Day of the week
Current Humidity
Current Temperature
OPERATING PRECAUTIONS
• Do not use or store this clock in areas exposed to temperature extremes, strong magnetism, strong vibration, or
strong impact.
• Heat can shorten battery life and cause malfunction. Keep the clock away from heaters and direct sunlight when
using it.
• Never use the clock in a bathroom or any other area subject to high humidity.
• Never try to take the clock apart. Doing so can cause malfunction.
• To clean the clock, use a soft, dry cloth or a cloth moistened in a solution of water and a mild neutral detergent.
Wring out all excess moisture from the cloth. Never use thinner, benzene, alcohol or other similar agents.
• The LCD may become diffi cult to read at temperatures outside of the operating temperature range (0 to 40°C).
• Display fi gures may be diffi cult to read when viewed from an angle.
• Be sure to keep all user documentation handy for future reference.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss suffered by you or
any third party arising through the use of this product or its malfunction.
1
Operation Guide ID-17
1
2
3
4
3
GENERAL GUIDE
°C/°F button
Press this button to toggle the temperature units between Celsius and Fahrenheit.
+ / – buttons
Use these buttons to change the setting that is fl ashing on the display.
SET button
Use this button when setting the current time.
RESET button
Press this button to reset the clock after replacing its batteries.
USING THE CLOCK
1. Press the SET button (3) to cycle through the setting screens as shown below.
Normal Timekeeping Screen Year Setting Screen
Contrast Setting Screen Month and Day Setting Screen
12-hour/24-hour Setting Screen Time Setting Screen
2. While the screen you want is displayed, use the + and – buttons (2) to change the fl ashing digits.
Press + to increase
• Holding down + or – changes the fl ashing digits at high speed.
• You can set the year in the range of 2000 to 2099. The day of the week is set automatically in accordance
with the date setting.
• Pressing + or – while the Time Setting Screen is on the display causes the seconds count to be reset to 00.
• Each press of + or – while the 12-hour/24-hour Setting Screen is on the display toggles between 12-hour and
24-hour timekeeping.
• You can set the contrast level in the range of 1 to 10.
3. After making the settings you want, use the SET button (
• The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display
for about three minutes without performing any operation.
the fl ashing digits.
Press – to decrease
the fl ashing digits.
) to display the Normal Timekeeping Screen.
THERMOMETER FUNCTIONS
• A built-in sensor measures temperature and shows the measured value on the display.
• The temperature display shows “LO” for temperatures below –19.9°C (–3.8°F) and “HI” for temperatures above
49.9°C (121.8°F).
• Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such
readings are actually outside the guaranteed temperature range of this clock.
Switching between Celsius and Fahrenheit
• Push the °C/°F button (1) to select either Celsius (°C) or Fahrenheit (°F).
Celsius (°C) Fahrenheit (°F)
°C/°F button (1)
°C °F
HYGROMETER FUNCTIONS
A built-in sensor measures humidity and shows the measured value on the display.
• The humidity display shows “LO” for humidity below 10% and “HI” for humidity above 90%.
• Whenever the current temperature is outside the range of 0°C to 49.9°C, the humidity display will show “– –”.
2
Loading...