Casio ID-15S Owner's Manual

MA1205-EA

2012 CASIO COMPUTER CO., LTD.

Operation Guide ID-15S

ILLUSTRATION

ALM/SNZ DEMO

MAX/MIN

ALM/SNZ DEMO

C/ F

ALM/SNZ DEMO

SNZ

OFF

RESETSET

MAX/MIN

OFF

RESET SET

1cm

• A sticker is affixed to the glass of the clock when you purchase it. Be sure to remove the sticker before using the clock.

• Depending on the clock model, its configuration may differ somewhat from that shown in the illustration.

PM indicator

Date (month - day)

Alarm Off Snooze Alarm On

Current time (Hour, minutes, seconds)

Day of the week

Current temperature

Alarm time

SNZ

OFF

RESET SET

C/ F

SNZ

Z N

S N O

Z N

D L A

F F O

T E

S T E

S E R

F / C

I M

/ X A M

Snooze on indicator

Alarm on indicator

GENERAL GUIDE

1 ALM/SNZ button

Pressing this button while the alarm is sounding stops the alarm.

2 DEMO button

Press this button to test the alarm sound.

3 Alarm Mode selector

SNZ: Snooze alarm on ON: Alarm on OFF: Alarm off

4 MAX/MIN button

Press this button to display the high and low temperature values.

°C/°F button

Press this button to toggle the temperature units between Celsius and Fahrenheit.

6 + / – buttons

Use these buttons to change the alarm time or the setting that is flashing on the display.

7 RESET button

Press this button to reset the clock after replacing its batteries.

8 SET button

Use this button when setting the current time.

USING THE CLOCK

1. Press the SET button (8) to cycle through the setting screens as shown below.

Normal Timekeeping Screen Contrast Setting Screen

Year Setting Screen

2. While the screen you want is displayed, use the + and

– buttons (6) to change the flashing digits.

• Holding down + or – changes the flashing digits at

high speed.

• You can set the year in the range of 2000 to 2099. The day of the week is set automatically in accordance with the date setting.

• Pressing + or – while the Time Setting Screen is on the display causes the seconds count to be reset to

00.

• Each press of + or – while the 12-hour/24-hour Setting Screen is on the display toggles between 12-hour and 24-hour timekeeping.

• You can set the contrast level in the range of 1 to 10.

3. After making the settings you want, use the SET button (8) to display the Normal Timekeeping Screen.

• The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display for about three minutes without performing any operation.

Setting Screen

Press + to increase the flashing digits.

12-hour/24-hour

Setting Screen

Time Setting ScreenMonth and Day

ALM/SNZ DEMO

MAX/MIN

C/ F

SNZ

OFF

RESETSET

Press – to decrease the flashing digits.

Operation Guide ID-15S

USING THE ALARM

The alarm sounds when the alarm time you set is reached. You can also use the Alarm Mode selector (3) to select the snooze alarm feature.

Setting the Alarm Time

Use the + and – buttons (6) to set the alarm time. Pressing the + and – buttons (6) causes the alarm time to appear in place of the date on the display.

• Holding down + or – changes the digits at high speed.

Turning the Alarm On and Off

Use the Alarm Mode selector (3) on the back of the clock to turn the alarm on and off, and to select the snooze feature.

Alarm Mode selector

SNZ

OFF

• The alarm time appears in place of the date on the display whenever the Alarm Mode selector (3) is set to ON

or SNZ.

• The volume of the alarm sound cycles through five levels as it sounds.

Stopping the Alarm

• When alarm is sounding, press the ALM/SNZ button (1) to stop it. When the snooze feature is turned on, the

alarm will sound again in about five minutes.

• To turn off the snooze feature, slide the Alarm Mode selector (3) to OFF.

The alarm sounds at the preset time for one minute, and up to seven more times every five minutes thereafter. Even if you stop the alarm by pressing the ALM/SNZ button (1), the alarm sounds again about five minutes later.

• The indicator activated.

flashes on the display to indicate that the snooze feature is

The alarm sounds at the preset time for one minute.

The alarm does not sound.

Press + to change the alarm time setting.

Description

ALM/SNZ DEMO

SNZ

OFF

RESETSET

MAX/MIN

C/ F

Press – to change the alarm time setting.

THERMOMETER FUNCTIONS

• A built-in sensor measures temperature and shows the measured value on the display.

• The temperature display shows “LO” for temperatures below –19.9°C (–3.8°F) and “HI” for temperatures above

49.9°C (121.8°F).

• Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such

readings are actually outside the guaranteed temperature range of this clock.

Switching between Celsius and Fahrenheit

• Push the °C/°F button (5) to select either Celsius (°C) or Fahrenheit (°F).

• Switching between Celsius and Fahrenheit causes current high temperature and low temperature memory

contents to be cleared.

Celsius ( C) Fahrenheit ( F)

C/ F button (5)

High Temperature and Low Temperature Memory

• The clock remembers the highest and lowest temperature readings for the current 24-hour day. Daily high and low values are cleared each day at midnight.

Changing the Temperature Display Screen

• Each press of the MAX/MIN button (4) cycles between screens as illustrated below.

Current temperature

MAX/NIN button (4) MAX/NIN button (4)

High temperature Low temperature

Turning On Temperature Screen Auto Cycling

• Hold down the MAX/MIN button (4) for about one second. This will turn on temperature screen auto cycling, which causes the screen contents to cycle as illustrated below at regular intervals.

MAX/NIN button (4)

Current temperature

High temperature Low temperature

• To turn off temperature screen auto cycling, press the MAX/MIN button (4).

+ 1 hidden pages