Casio GQ-200-1, GQ-200 User Manual
GQ-100/200
GQ-100/200-1
BEFORE USING THE UNIT FOR THE FIRST TIME…
1. Use a phillips head screwdriver to open the
battery compartment cover on the back of the
unit.
2.Remove the insulating paper from between the
batteries and contacts.
3.Replace the battery compartment cover.
GENERAL GUIDE
• The configuration of your clock may differ somewhat from that shown in the
illustration.
• Hold down the Snooze/Light button to illuminate the display. The display
remains illuminated for a few seconds after you release the button.
GQ-100 GQ-200
Snooze/Light button
Current time
- TIME SET +
Alarm time
Control buttons
[Back] [Back]
Alarm On/Off switch
All reset button
ALARM
ON
RESET
OFF
Battery
compartment
cover
RESET
ALARM SET
+-
TIME SET
[Bottom]
Control buttons
SETTING THE TIME
[Control buttons]
GQ-100: on the front
–
TIME-SET
1. Hold down TIME-SET until the time starts to
flash on the display.
2.Each press of the
+
one minute, and pressing
+ button increases the time by
– decreases it by one
minute.
USING THE ALARM
The alarm of this clock features a Snooze Function, which lets you catch a few
more minutes sleep in the morning. For full details on how to use this function,
see “To use the alarm”.
To set the alarm
[Control buttons]
GQ-100: on the front
–+
Each press of the
one minute, and pressing
minute.
• Holding down either button changes the time
setting at high speed.
• The hour setting is changed automatically
GQ-200: on the bottom
+–
ALARM SET
+-
TIME SET
whenever a change in the minutes increases
past 59 minutes or decreases past 00 minutes.
• The time display uses a 12-hour format, so
evening is indicated by “PM”.
GQ-100
Current time
Alarm time
To switch the alarm on and off
Slide the Alarm On/Off switch to the ON position to switch the alarm on, or to
the OFF position to switch it off.
• When you switch the alarm on, the alarm on indicator “
display.
Alarm on/off switch
(GQ-100: on the back
GQ-200: on the side)
ALARM
ON
RESET
OFF
GQ-100
ON
+ button increases the time by
– decreases it by one
GQ-200
” appears on the
GQ-200
ON
GQ-200: on the bottom
TIME-SET
+–
ALARM SET
+-
TIME SET
• Holding down either button changes the time
setting at high speed.
• The hour setting is changed automatically
whenever a change in the minutes increases
past 59 minutes or decreases past 00 minutes.
• The seconds are reset to “00” whenever you
change the minutes setting.
• The time display uses a 12-hour format, so
evening is indicated by “PM”.
GQ-100
GQ-200
Current time
Alarm time
3.After you finish setting the time press TIME-SET to return to the Normal
Display.
• If you do not operate any button for a few minutes while the time is flashing,
the flashing stops and the clock goes back to the Normal Display automatically.
OFF
On
OFF
Off
To use the alarm
1. Set the alarm time and switch the alarm on.
2. When the alarm time you set is reached, the alarm starts to sound. It
continues for about one minute or until you stop it by pressing the Snooze/
Light button.
Snooze/Light button
GQ-100 GQ-200
• When the alarm starts to sound, the alarm on indicator “
” flashes on the
display. This indicates that the Snooze function is activated.
3.About four minutes after you press the Snooze/Light button, the alarm starts
to sound again.
4.The above repeats up to seven times, or until you switch the alarm off (by
sliding the Alarm On/Off switch to the OFF position).
• You can stop the repeating alarm at any time by sliding the Alarm On/Off
Switch to the OFF position.
• The beep pattern of the alarm changes (becomes faster) as the alarm
sounds. The pattern changes up to five times.
BATTERY REPLACEMENT
Replace the batteries whenever the display of the clock becomes dim and
difficult to read, or when the display light fails.
To replace batteries
1.Use phillips head screwdriver to open the battery compartment cover on the
back of the unit.
2.Remove both old batteries.
3.Load two new AA-size batteries. Make sure that their positive (+) and negative
(-) ends face in the correct directions. If you load batteries incorrectly they can
leak and cause damage to the clock.
4.Replace the battery compartment cover.
5.Press the all reset button to reset the digital display information.
6.Set the current time and alarm time.
[Back]
GQ-100 GQ-200
ALARM
ON
OFF
RESET
All reset button
RESET
GQ-100/200-2
Battery
compartment
cover
ALARM SET
+-
TIME SET
Battery
compartment
Loading...