Casio 5134 Owner's Manual

MA1007-EB

Operation Guide 5134

About This Manual

Depending on the model of your watch, its display may have dark ﬁgures on a light • background or light ﬁgures on a dark background. The display also may be with a graphic area or without a graphic area. All samples in this manual show dark ﬁgures on a light background, with a graphic area. Button operations are indicated using the letters shown in the illustration. • For the sake of simplicity, the sample displays in this manual do not show the analog • hands of the watch. Each section of this manual provides you with the information you need to perform • operations in each mode. Further details and technical information can be found in the “Reference” section.

With graphic area Without graphic area

Graphic area

General Guide

Press • C to change from mode to mode. In any mode (except when a setting screen is on the display), press • B to illuminate the display.

Timekeeping Mode World Time Mode Alarm Mode Stopwatch Mode Countdown Timer

Press C.

Mode

Timekeeping

This watch features separate digital and analog timekeeping. The procedures for setting the digital time and analog time are different.

In the Timekeeping Mode, you can press • D to change the display format as shown below.

Day of the Week

and Day

Seconds

Press D.

Digital Time and Date

Use the Timekeeping Mode to set and view a digital display of the current time and date. When setting the digital time, you can also conﬁgure settings for summer time (Daylight Saving Time or DST), your Home City code (the code for the city where you normally use the watch), the 12/24-hour format.

This watch is preset with a number of city codes, each of which represents the time • zone where that city is located. When setting the digital time, it is important that you select the correct city code for your Home City. If your location is not included in the preset city codes, select the preset city code that is in the same time zone as your location. Note that all of the times for the World Time Mode city codes are displayed in • accordance with the digital time and date settings you conﬁgure in the Timekeeping Mode. After you correctly set your Home City time and date, you can set the watch up for • timekeeping with a different city code simply by changing the Home City code in the Timekeeping Mode.

To set the digital time and date

Press 3. C to move the ﬂashing in the sequence shown below to select the other settings.

Seconds DST Home City Code Hour Minutes

In the Timekeeping Mode, hold down 1. A until the seconds start to ﬂash, which indicates the setting screen. Press 2. C twice to move the ﬂashing to the Home City code setting, and then use B and D to select the code you want.

Make sure you select your Home City code before • changing any other setting. For full information on city codes, see the “City Code • Table”.

Hour : Minutes

PM indicator

Hour : MinutesDayDay of week

12/24-Hour FormatYearMonthDay

When the setting you want to change is ﬂashing, use 4. B and D to change it as described below.

Screen To do this: Do this:

Reset the seconds to

Toggle between Daylight Saving Time ( ) and Standard Time ( )

Change the Home City code

Change the hour or minutes

Toggle between 12-hour ( ) and 24-hour ( ) timekeeping

Change the year

Change the month or day

Press 5. A to exit the setting screen.

Resetting the seconds only (without changing the DST, Home City code, hour, or • minute setting) causes the analog minute hand setting to be adjusted automatically. See “Digital Time Daylight Saving Time (DST) Setting” below for details about the • DST setting. The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is • applied in all modes.

Digital Time Daylight Saving Time (DST) Setting

Daylight Saving Time (summer time) advances the digital time setting by one hour from Standard Time. Remember that not all countries or even local areas use Daylight Saving Time.

To toggle the Timekeeping Mode digital time between DST and Standard Time

DST indicator

In the Timekeeping Mode, hold down 1. A until the seconds start to ﬂash, which indicates the setting screen. Press 2. C once to display the DST setting screen. Press 3. D to toggle between Daylight Saving Time

displayed) and Standard Time ( displayed).

( Press 4. A to exit the setting screen.

The DST indicator appears on the Timekeeping Mode • screen to indicate that Daylight Saving Time is turned on.

Press D.

Use D (east) and B (west). Use D (+) and B (–).

Press D.

Use D (+) and B (–).

Analog Time Setting

Perform the procedure below when the time indicated by the analog hands does not match the time of the digital display.

To adjust the analog time

In the Timekeeping Mode, hold down 1. D for about three seconds until the lower right display ﬁrst shows H-SET and then the current digital time. This is the analog hand adjustment mode. Press 2. D to advance the analog time setting by 20 seconds.

Holding down • D advances the analog time setting at high speed. If you need to advance the analog time setting a long • way, hold down D until the time starts advancing at high speed, and then press B. This locks the highspeed hand movement, so you can release the button. High-speed hand movement continues until you press any button. It will also stop automatically after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal, or countdown beeper) starts to sound.

Operation Guide 5134

Press 3. A to exit the setting screen.

The watch will automatically adjust the minute hand slightly to match its internal • second count when you exit the setting screen.

World Time

City code

Current time for the selected city code

To toggle a city code time between Standard Time and Daylight Saving Time

DST indicator

You will not be able to change the DST/Standard Time setting of the city code • currently selected as your Home City. Note that you cannot switch between Standard Time and Daylight Saving Time while •

is selected as the city code.

World Time digitally displays the current time in 48 cities (29 time zones) around the world.

All of the operations in this section are performed in the • World Time Mode, which you enter by pressing C.

To view the time in another city

In the World Time Mode, press D to scroll eastwardly through city codes.

For full information about city codes, see the “City Code • Table”. If the current time shown for a city is wrong, it probably • means there is a problem with your Timekeeping Mode time and/or Home City code settings. Go to the Timekeeping Mode and make the necessary adjustments.

In the World Time Mode, use 1. D to display the city code whose Standard Time/Daylight Saving Time setting you want to change. Hold down 2. A for about one second to toggle between Daylight Saving Time (DST indicator displayed) and

Standard Time (DST indicator not displayed). The DST indicator is on the display whenever you display • a city code for which Daylight Saving Time is turned on. Note that the DST/Standard Time setting affects only • the currently displayed city code. Other city codes are not affected.

Alarm

Alarm time (Hour : Minutes)

Alarm on indicator

Hourly time signal on indicator

To set an alarm time

When setting the alarm time using the 12-hour format, take care to set the time • correctly as a.m. (no indicator) or p.m. (P indicator).

Press 4. A to exit the setting screen.

Alarm Operation

The alarm sounds at the preset time for about 20 seconds, regardless of the mode the watch is in.

Alarm and Hourly Time Signal operations are performed in accordance with the • Timekeeping Mode digital time. To stop the alarm tone after it starts to sound, press any button. •

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn the alarm and the hourly time signal on and off

You can set one Daily Alarm. When the alarm is turned on, the alarm tone sounds when the alarm time is reached. You can turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour.

Pressing • D cycles through the available alarm and hourly time signal combinations. All of the operations in this section are performed in the • Alarm Mode, which you enter by pressing C.

In the Alarm Mode, hold down 1. A until the hour setting

of the alarm time starts to ﬂash, which indicates the

setting screen.

This operation automatically turns on the alarm. •

Press 2. C to move the ﬂashing between the hour and

minute settings.

While a setting is ﬂashing, use 3. D (+) and B (–) to

change it.

In the Alarm Mode, you can use 1. D to cycle through the

available alarm and hourly time signal combinations as

shown below.

Stopwatch

1/100 second

Minutes

SPL indicator

To measure times with the stopwatch

Elapsed Time

D D

Start Stop Re-start Stop Clear

Split Time

D A

Start Split

Two Finishes

D A

Start Split

The stopwatch lets you measure elapsed time, split times, and two ﬁnishes.

The display range of the stopwatch is 59 minutes, 59.99 • seconds. The stopwatch continues to run, restarting from zero after • it reaches its limit, until you stop it. The stopwatch measurement operation continues even if • you exit the Stopwatch Mode. Exiting the Stopwatch Mode while a split time is frozen • on the display clears the split time and returns to elapsed time measurement. All of the operations in this section are performed in the •

Seconds

Stopwatch Mode, which you enter by pressing C.

D D

A D

(SPL indicator displayed)

First runner ﬁnishes. Display time of ﬁrst runner.

Split release Stop Clear

D A

Stop

Second runner ﬁnishes.

Split release

Display time of second runner.

Clear

Countdown Timer

The countdown timer can be set within a range of one

Seconds

Hours : Minutes

To conﬁgure the countdown timer

When the setting you want to change is ﬂashing, use 3. B and D to change it as described.

Setting Screen Button Operation

Start Time

Press 4. A to exit the setting screen.

To use the countdown timer

minute to 24 hours. An alarm sounds when the countdown reaches zero.

All of the operations in this section are performed in the • Countdown Timer Mode, which you enter by pressing C.

While the countdown start time is on the display in the 1. Countdown Timer Mode, hold down A until the current countdown start time starts to ﬂash, which indicates the setting screen.

If the countdown start time is not displayed, use the • procedure under “To use the countdown timer” to display it.

Press 2. C to move the ﬂashing between the hours and minutes digits.

Hours Minutes

Use D (+) and B (–) to change the setting.

• You can set a start time in the range of 1 minute to 24 hours in 1-minute increments.

Press D while in the Countdown Timer Mode to start the countdown timer.

The countdown timer operation continues even if you exit • the Countdown Timer Mode. Press • D while a countdown operation is in progress to pause it. Press D again to resume the countdown. To completely stop a countdown operation, ﬁrst pause • it (by pressing D), and then press A. This returns the countdown time to its starting value.

Illumination

An LED (light-emitting diode) illuminates the display for easy reading in the dark.

Alarm on indicator

Hourly time signal on indicator

Alarm On Signal On

The alarm on indicator and hourly time signal on indicator are shown in all modes. • The alarm on indicator ﬂashes while the alarm is sounding. •

Alarm Off Signal Off

Alarm On Signal Off

Alarm Off Signal On

Illumination Precautions

The illumination provided by the light may be hard to see when viewed under direct • sunlight. Illumination automatically turns off whenever an alarm sounds. • Frequent use of illumination runs down the batteries. •

To turn on illumination

In any mode (except when a setting screen is on the display), press B to turn on illumination.

+ 1 hidden pages