MA0302-A
USER’S GUIDE 2737/2738
|
∑ The operational procedures for Modules 2737 and 2738 |
|
are identical. All of the illustrations in this manual show |
|
Module 2737. |
|
∑ All of the displays in this manual show black-on-white. |
|
∑ Button operations are indicated using the letters shown |
|
in the illustration. |
|
∑ Each section of this manual provides you with the |
Module 2737 |
information you need to perform operations in each |
|
mode. Further details and technical information can be |
|
found in the “Reference” section. |
Module 2738
∑Press Cto change from mode to mode.
∑In any mode, press Bto illuminate the display.
Timekeeping Mode |
World Time Mode |
Countdown Timer Mode |
Stopwatch Mode |
Alarm Mode |
Hand Setting Mode |
Press
C.
This watch features separate digital and analog timekeeping. The procedures for setting the digital time and analog time are different.
∑In the Timekeeping Mode, you can press Dto change the display format as shown below.
Day of the Week |
Month – Day |
Hour : Minutes |
|
|
PM |
|
|
indicator |
Seconds
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and date. When setting the digital time, you can also configure settings for summer time (Daylight Saving time or DST), your Home City code (the code for the city where you normally use the watch), and the 12/24-hour format.
∑This watch is preset with a number of city codes, each of which represents the time zone where that city is located. When setting the digital time, it is important that you select the correct city code for your Home City. If your location is not included in the preset city codes, select the preset city code that is in the same time zone as your location.
∑Note that all of the times for the World Time Mode city codes are displayed in accordance with the digital time and date settings you configure in the Timekeeping Mode.
∑After you correctly set your Home City time and date, you can set the watch up for timekeeping with a different city code simply by changing the Home City code in the Timekeeping Mode.
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting
screen.
2. Press Ctwice to move the flashing to the Home City
code setting (see the illustration below), and then use
B and Dto select the code you want.
∑ Make sure you select your Home City code before changing any other setting.
∑For full information on city codes, see the “City Code Table”.
3.Press Cto move the flashing in the sequence shown below to select the other settings.
|
Seconds |
|
|
|
DST |
|
|
Home City Code |
|
|
|
Hour |
|
|
Minutes |
|||||
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Day |
|
|
|
Month |
|
|
Year |
|
|
|
|
|
12/24-Hour format |
||||||
|
|
|
|
|
|
|
|
4.When the setting you want to change is flashing, use Band Dto change it as described below.
Screen |
To do this: |
Do this: |
|
Reset the seconds to 00 |
Press D. |
|
Toggle between Daylight Saving Time (ON) and |
Press D. |
|
Standard Time (OF) |
|
|
Change the Home City code |
Use D (east) and B(west). |
|
Change the hour or minutes |
Use D (+) and B(–). |
|
Toggle between 12-hour (12H) and 24-hour |
Press D. |
|
(24H) timekeeping |
|
|
Change the year |
Use D (+) and B(–). |
|
Change the month or day |
|
5. Press A to exit the setting screen.
∑See “Digital Time Daylight Saving Time (DST) Setting” below for details about the DST setting.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour from Standard Time. Remember that not all countries or even local areas use Daylight Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down Auntil the seconds start to flash, which indicates the setting screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (ON
displayed) and Standard Time (OF displayed).
4. Press Ato exit the setting screen.
∑ The DST indicator appears on the Hour : Minutes screen only to indicate that Daylight Saving Time is turned on.
∑ The Module 2738 DST indicator is displayed as.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not match the time of the digital display.
To adjust the analog time
1. In the Timekeeping Mode, press C five times to enter the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting screen.
3. Press D to advance the analog time setting by 20 seconds.
∑ Holding down D advances the analog time setting at high speed.
∑If you need to advance the analog time setting a long way, hold down Duntil the time starts advancing at high speed, and then press B. This locks the highspeed hand movement, so you can release the two buttons. High-speed hand movement continues until you press any button. It will also stop automatically after the time advances 12 hours or if an alarm (daily alarm or countdown beeper) starts to sound.
4.Press Ato exit the setting screen.
∑The watch will automatically adjust the minute hand slightly to match its internal second count when you exit the setting screen.
∑To return to the Timekeeping Mode, press C.
1