Casio 1798, 2301, 2301-1 General Manual
1798/2301-1
Module No.1798/2301
GENERAL GUIDE
• Press
CC
CC
C to change from mode to mode.
• Holding down
CC
CC
C for a few seconds in any mode enters the Stopwatch Mode. Holding down
CC
CC
C in the Stopwatch Mode changes to the Timekeeping Mode.
• There are two stopwatches in the Stopwatch Mode. Press
CC
CC
C while in the Stopwatch Mode to toggle between them. See “STOPWATCH MODE” for more information.
• At any time except while making settings, press
DD
DD
D to illuminate the display for about 4 seconds.
TIMEKEEPING MODE
• In the Timekeeping Mode, press
BB
BB
B to switch between the 12-hour and 24-hour
formats.
To set the time and date
1.Hold down
AA
AA
A until the seconds digits start to flash.
2.Press
CC
CC
C to move the selection around the display in
the following sequence.
Seconds Hour
Minutes
Day YearMonth
3. While the seconds digits are selected (flashing), press
DD
DD
D to reset the seconds to
00. If you press
DD
DD
D while the seconds count is in the range of 30 to 59, they are
reset to 00 and 1 is added to the minutes. If the seconds count is in the range of 00
to 29, the minutes count is unchanged.
4. While any other digits (besides seconds), are selected (flashing), press
DD
DD
D to in-
crease the number or
BB
BB
B to decrease it. Holding down either button changes the
digits at high speed.
• The date can be set with the range of January 1,1995 to December 31, 2039.
5.After you are set the time and date, press
AA
AA
A to return to the Timekeeping Mode.
• The day of the week is automatically set in accordance with the date.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
• When the time shown on the display does not match the analog setting, see
“H-SET MODE” to correct the analog setting.
ABOUT THE BACKLIGHT
• Hold down
DD
DD
D to illuminate the display for about 4 seconds. The backlight is dis-
abled while an input screen (with a flashing setting) is on the display.
• The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
• Frequent use of the backlight shortens the battery life.
• The watch emits an audible sound whenever the display is illuminated. This does
not indicate malfunction of the watch.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The backlight automatically turns off whenever an alarm sounds.
STOPWATCH MODE
The Stopwatch Mode automatically saves the best five lap times in memory, along
with lap numbers. You can later recall the saved data using the “RESULT MODE”.
The Stopwatch Mode provides you with the following types of stopwatch capabilities.
Single Stopwatch
This is a standard stopwatch that measures elapsed time and lap times.
Dual Stopwatch
This stopwatch lets you measures the times of two cars or runners at the same
time.
Selecting the Stopwatch Type
While in the Stopwatch Mode, press
CC
CC
C to toggle between the Single Stopwatch and
Dual Stopwatch. Note that the
CC
CC
C button is disabled while a stopwatch timing opera-
tion is in progress.
Depending on your watch model, the stopwatch display indicators may show CAR1
and CAR2 or STW1 and STW2.
Single Stopwatch Dual Stopwatch
Stopwatch type
indicator
Single Stopwatch
The Single Stopwatch is a standard stopwatch that measures elapsed time and lap
times.
Lap time
Total time
Hours
Minutes
Seconds
Minutes
Seconds
1/100 Second
To measure elapsed time with the Single Stopwatch
1.Press
BB
BB
B to start timing.
2.Press
BB
BB
B again to stop timing.
You can repeat steps 1 and 2 as many times as you like.
3.Pressing
AA
AA
A while timing is stopped resets the display to all zeros.
To measure lap times with the Single Stopwatch
1.Press
BB
BB
B to start timing.
2.Pressing
AA
AA
A while an timing operation is in progress displays the lap time in the
upper part of the display and the lap number in the lower part. This information
remains displayed for about four seconds, after which the elapsed time display
returns.
You can repeat step 2 as many times as you like.
3.Press
BB
BB
B to stop timing.
4.Pressing
AA
AA
A while timing is stopped resets the display to all zeros.
• The final time on the display when you press
BB
BB
B to stop timing is not stored into
memory as a lap time. If you want to save the final time, press
AA
AA
A and then
BB
BB
B.
Dual Stopwatch
Use the Dual Stopwatch to measure the times of two cars or runners at the same
time. You can also produce lap times for both and determine the difference between
them.
• The Dual Stopwatch is designed to time two runners or cars starting or passing at
different times. Accurate measurement is not possible when both start or pass at
the same time or close to the same time.
To use the Dual Stopwatch
1.Press
BB
BB
B to start timing of the first starter, which appears in the upper part of the
display.
2. Press
AA
AA
A to start timing of the second starter, which appears in the lower part of the
display.
3.When the first starter passes the timing points, press
BB
BB
B.
4.When the second starter passes the timing points, press
AA
AA
A.
• The difference between the two times appears on the display for about four seconds. After that, each lap time appears for about four seconds.
• If the time of the second starter is faster than that of the first, the time difference is
displayed as a negative value.
• If the time difference is 10 minutes or more, -- -- -- is displayed in place of the time.
• If the times being compared are from different laps, the time difference is shown
without a plus or minus indication.
• Hold down
AA
AA
A or
BB
BB
B to stop timing. The final time on the display when you hold down
AA
AA
A or
BB
BB
B to stop timing is not stored into memory as a lap time. If you want to save
the final time, press
AA
AA
A or
BB
BB
B, and then hold down
AA
AA
A or
BB
BB
B to stop timing.
RESULT MODE
Use this mode to view the best five lap times and lap numbers. Lap times are stored
by either a Single Stopwatch or Dual Stopwatch operation. Current memory contents
are always the results produced by the last stopwatch operation.
If you know the length of a lap, you can input it and calculate the speed as well. You
can input or change the length either before or after the timing operation.
To input the length of a lap
1.Hold down
AA
AA
A until the kilometers digits start to flash on the display
2. Each press of
CC
CC
C moves the input position between the kilometers digits and the
decimal digits.
3.After inputting the value you want, press
AA
AA
A to save it.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Result Mode automatically.
Result ModeTimekeeping
Mode
H-SET Mode Single
Stopwatch
Dual Time Mode Alarm Mode Dual
Stopwatch
Stopwatch Mode
Month Day Day of
week
Hour
Minutes
Seconds
PM
indicator
Lap time
(second starter)
Start/Lap
(second starter)
Start/Lap
(first starter)
Lap time
(first starter)
Minutes
Seconds
1/100 Second
1798/2301-2
Viewing Result Mode Data
Press
BB
BB
B to cycle through the best five lap times. Pressing
AA
AA
A while a lap time is on
the display shows the average speed for the lap. Press
AA
AA
A again to return to the lap
time.
• Pressing
BB
BB
B while the average speed is on the display advances to the next lap
time.
• If the average speed is 1000 km/h or more, E r r is displayed in place of the average
speed.
Hour
Minutes
Hour
Minutes
Mode indicator
Hour Minutes
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
4.After you set the alarm time, press
AA
AA
A to return to the Alarm Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To stop the alarm
• Press any button to stop the alarm after it starts to sound.
To turn the Daily Alarm and Hourly Time Signal on and off
Press
BB
BB
B while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
To test the alarm
Hold down
BB
BB
B while in the Alarm Mode to sound the alarm.
Note that this operation also changes the Daily Alarm and Hourly Time Signal on/off
setting.
H-SET MODE
When the time shown on the display does not match the analog setting, use this
mode to correct the analog setting.
To set the analog time
1. Hold down
AA
AA
A while in the H-SET Mode until the digital time (hour and minutes)
starts to flash on the display.
• The following step changes the hands of the analog timepiece without changing the flashing digital time.
2.Press
DD
DD
D to advance the hand setting of the analog time-
piece. Holding down
DD
DD
D changes the hand setting at high
speed.
• Pressing
BB
BB
B while holding down
DD
DD
D causes the hand set-
ting to change at high speed. The hands continue to
move even when you release the buttons. Press
DD
DD
D or
BB
BB
B to stop them.
• The analog time setting does not stop automatically when
it reaches the current time. You must stop the hands
manually.
• Note that there is not function for moving the hands back,
so be sure that you stop any high-speed hand setting
operation before the time you want to set is reached.
3.After you set the analog time, press
AA
AA
A to return to the H-SET Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the H-SET Mode automatically.
Both OFF Daily Alarm
Only
Hourly Time
Signal Only
Both ON
Mode indicator
SecondsHour
Minutes
Lap number Order
Mode indicator
Stopwatch type
indicator
Lap time
Total time
Single Stopwatch
Lap number
(first starter)
Order
(first starter)
Stopwatch type
indicator
Lap time
(first starter)
Lap time
(second starter)
Lap number
(second starter)
Order
(second starter)
Dual Stopwatch
Mode indicator
SecondsHour
Minutes
Deleting Result Mode Data
Result Mode data is deleted automatically whenever you perform a new stopwatch
timing operation. To manually delete data, hold down
BB
BB
B and
DD
DD
D in the Result Mode
until the message CLR appears on the display.
DUAL TIME MODE
To set the Dual Time
1. Hold down
AA
AA
A until the hour digits start to flash on the
display. The hour digits flash because they are selected.
2.Press
CC
CC
C to change the selection in the following se-
quence.
3. Press
DD
DD
D to increase the number or
BB
BB
B to decrease it.
Holding down either button changes the current number at high speed.
4. After you set the dual time, press
AA
AA
A to return to the
Dual Time Mode.
• The format (12-hour and 24-hour) of the dual time matches the format you select for normal timekeeping.
• In the Dual Time Mode, the seconds count is synchronized with the seconds count
of the Timekeeping Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Dual Time Mode automatically.
Switching Dual Time and the Current Time
Holding down
BB
BB
B for about two seconds in the Dual Time Mode causes the Dual Time
and current time to be reversed. The hands of the watch move at high speed to the
correct time. To switch back, simply hold down
BB
BB
B again in the Dual Time Mode.
ALARM MODE
When the Daily Alarm is turned on, an alarm sounds for
20 seconds at the preset time each day. When the Hourly
Time Signal is turned on, the watch beeps every hour on
the hour.
1. Hold down
AA
AA
A until the hour digits start to flash on the
display. The hour digits flash because they are selected. At this time the Alarm is automatically switched on.
2.Press
CC
CC
C to change the selection in the following se-
quence.
3. Press
DD
DD
D to increase the number or
BB
BB
B to decrease it.
Holding down either button changes the current number at high speed.
Flashing
Loading...